Black & Decker 1101 User Manual
DRILLING
To prevent the drill bit from slipping when starting a hole, make an indentation with a centerpunch and hammer at the point to be drilled. Place the point of the bit in the Indentation and
start drilling.
CARE m DRILLING
Twist drills are brittle and will
break if enough bending stress
it applied. To avoid stress on
the drill bit, try extending your
index finger along the side of
the drill-housing with your mid
dle finger on the trigger. Re
member— guide, the tool, don't
force it! Should the tool be
come overheated, run it with
no load. Because of the drill's
construction, it will cool faster
running than by stopping it.
TO REMOVE CHUCK for using a threaded shank acces
sory, first insert key into chuck key hole. Then strike the
key sharply with a piece of wood in the direction the
chuck rotates when the Drill is turned "ON." This will
loosen the chuck shank threads and the chuck may be
unscrewed from the Drill.
DRILLING IN METAL
Use a cutting lubricant when
drilling metals. The excep
tions are iron and brass which
should be drilled dry. The
cutting lubricants that work
best are sulphurized cutting
oil or lard oil; bacon grease
will also serve the purpose.
Aluminum is best drilled with
turpentine or kerosene.
DRILLING IN WOOD
Holes in wood can be made
with the same twist drills used
for metal. These bits may over
heat unless pulled out fre
quently to clear chips from the
flutes. For larger holes, use
Power Drill Wood Bits with a
shank size that will fit your
drill's chuck. Work that is apt
to splinter should be backed up
with a block of wood. Let up on
the pressure Just before the tip
cuts through, this will give a
good clean hole. Always leave
the drill running when pulling
it back out of a drilled hole,
this prevents Jamming.
LUBRICATION
Seif lubricating bearings are used in the tool and periodic relubrication Is not required.
However, it is recommended that, at least once a year, you take or send the too! to a
B&D Service Center for a thorough cleaning, inspection and lubrication of the gear case.
GUARANTEE
Black & Decker guarantees, for one year from date of purchase, to correct by
repair or parts replacement without charge any defect due to faulty material
or workmanship. Simply return the complete unit, transportation prepaid, to
any Black & Decker Service Center or Authorized Service Station. Naturally,
we assume no responsibility for damage caused by misuse, careless handling
or where repairs have been made or attempted by others. No other guarantee,
written or verbal, is authorized by us.
OWNER’S MANUAL
\
iWi
CEftiEi
OHUOIC
mmm switch^
SWITCH
LOCKINO
BOTTOI
IMPORTANT!
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjust
ment should be performed by BLACK & DECKER Service Centers or other
qualified service organizations, always using BLACK & DECKER replacement
parts.
See'Tools-Electric'
—Yellow Pages—
for Service l< Sales
THE BLACK & DECKER MFC. CO., TOWSON, MD. 21204, U.S.A.
Form No. 97142 (B5-AL) Printed in U.S.A.
'/<" DR IL L #1 00 0
Vt
D RI LL *1 10 1
Capacity: 14" holes in steel; In hard
wood. 115 Volts A.C. 1.9 Amps. 1/7 H.P.
2250 R.P.M.
Capacity: %" holes in steel; in hard
wood. 115 Volts A.C. 2.0 Amps. 1/7 H.P.
1000 R.P.M.
Blacks. Decken, NOS. 1000 AND 1101 DRILLS
P.T.L SAFETY RULES
FOR POWER TOOLS
1. KNOW YOUR POWER TOOL--Read owner's manual care
fully. Learn its applications and limitations as well as the
specific potential hazards peculiar to this tool.
GROUND ALL TOOLS ~ UNLESS DOUBLE-INSULATED. If
2.
tool is equipped with three-prong plug, it should be plugged
into a three-hole electrical receptable. If adapter is used to
accommodate two-prong receptacle, the adapter wire must
be attached to a known ground. Never remove third prong.
KEEP GUARDS IN PLACE and in working order.
3.
KEEP WORK AREA CLEAN. Cluttered areas and benches
4.
invite accidents.
AVOID DANGEROUS ENVIRONMENT. Don't use power tool
in damp or wet locations. And keep work area well lit.
KEEP CHILDREN AWAY. All visitors should be kept safe dis
6.
tance from work area.
7. STORE IDLE TOOLS. When not in use, tools should be
stored in dry, high or locked-up place — out of reach of
children.
8. DON'T FORCE TOOL. It will do the job better and safer at
the rate for which it was designed.
9. USE RIGHT TOOL. Don't force small tool or attachment to
do the job of a heavy duty tool.
10. WEAR PROPER APPAREL. No loose clothing or jewelry to
get caught in moving parts. Rubber gloves and footwear are
recommended when working outdoors.
11. USE SAFETY GLASSES with most tools. Also face or dust
mask if cutting operation is dusty.
12. DON'T ABUSE CORD. Never carry tool by cord or yank it to
disconnect from receptacle. Keep cord from heat, oil and
sharp edges.
13. SECURE WORK. Use clamps or a vise to hold work. It's
safer than using your hand and it frees both hands to
operate tool.
14. DON'T OVERREACH. Keep proper footing and balance at all
times.
15. MAINTAIN TOOLS WITH CARE. Keep tools sharp at all
times, and clean for best and safest performance. Follow
Instructions for lubricating and changing accessories.
16. DISCONNECT TOOLS. When not In use, before servicing,
when changing accessories such as blades, bits, cutters, etc.
17. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit
of checking to see that keys and adjusting wrenches are
removed from tool before turning it on.
18. AVOID ACCIDENTAL STARTING. Don't carry plugged-in tool
with finger on switch.
GROUNDING (Continued)
If the unit requires from 150 to 250 volts, it has a plug like
Fig. “C". No adapter is available and the plug must be used in
the proper 3-wire grounding receptacle.
If you use an extension cord, be sure that it is a 3-conductor,
grounding type cord. Grounding must be continuous from the
tool plug to the grounded receptacle.
GROUNDED OUTLET BOX
/
GROUNDING
PRONG IS
LONGEST OF
THE 3 PRONGS
GROUNDED
OUTLET BOX
ADAPTER
GREEN
GROUNDING
WIRE
GROUNDED OUTLET BOX^
©
GROUNDING
PRONG IS
LONGEST OF
THE 3 PRONGS
m
©
EXTENSION CORD
When using the tool at a considerable distance from power
source, a 3-conductor, grounding-type extension cord of ade
quate size must be used for safety, and to prevent loss of power
and over-heating. Use the table below for 120-volt tools. For
220-volt tools, see same chart but use a wire size corresponding
to an extension cord length shown which is V2 the length of
extension to be used.
P.T.I. Safety Rule #12 applies to Extension Cords as well as the
Tool Power Cord. Before using cords, inspect them for loose or
exposed wires and damaged insulation. Make any needed repairs
or replacement before using your power tool.
Ext. Cord Length in feet . .
Required Wire Size (A.W.G.)
.25 50 75 100 150 200
.18 18 18 18 16 16
SWiTCH
To start drill, depress trigger switch; to stop drill, release trigger.
To lock trigger in "ON" position for continuous operation, or
when using Drill In a Vertical or Horizontal Stand, depress
trigger and push in locking button (located behind the trigger),
then gently release trigger. To release locking mechanism, de
press trigger fully, then release it.
C
GROUNDING
These units are equipped with approved 3-conductor power cord
and 3-prong grounding type attachment plug to be used with the
proper grounding type receptacle. In accordance with the
National Electrical Code, Canadian Electrical Code, and
Underwriters' Laboratories specifications. The green colored
conductor in the cord is the grounding wire. Never connect the
green wire to a "live" terminal.
If your unit requires less than 150 volts it has a plug that looks
like Fig. “A". It will fit directly into the proper type of 3-wire
grounding receptacle. The unit is then grounded automatically
each time it is plugged in.
Shown in Fig. '‘B" is a special grounding adapter (not allowed
in Canada by the Canadian Electrical Code) which is available
from your dealer and will permit using a 2-wire receptacle.
The green grounding wire extending from the side of the adapter
must be connected to a Permanent Ground.
Form No. 97142
CHUCK
Turn collar to open chuck jaws. Place bit in chuck so that end
rests on chuck bottom. Tighten chuck collar by hand. Place
chuck key in each of the three holes, and tighten in clockwise
direction. It's Important to tighten chuck with all three holes.
This is a safety feature that prevents bit slippage and motor
damage. To release bit, turn chuck key counterclockwise in just
one hole, then loosen chuck by hand.
Loading...