Black Box TS870A, TS875A, TS155-R3 Specifications
1
Black Box Corporation • 1000 Park Drive • Lawrence, PA 15055-1018 • Tech Support: 724-746-5500 • www.blackbox.com • e-mail: info@blackbox.com
© 2005. All rights reserved.
Black Box Corporation.
1/18/2005 #26365
Test for shorts, opens,
miswires, reversals,
and split pairs.
Cable test results are
displayed in wire map
format with a message
line for shorts and split
pairs.
Automatic start-up
and shutdown: just
plug both ends of the
cable into the tester.
Two-line by
16-character
alphanumeric LCD
with icons shows
clear results.
T
est new or installed premise
wiring for networks and data
systems with the LANTest or
LANTest Pro Kit. It checks
shielded and unshielded UTP and
STP CAT3, CAT4, CAT5, and CAT6,
and also coax cables. (Adapters
for coax are included with the
LANTest Pro Kit.)
Use the tester three ways:
without the remote, with the
remote, or with the Network
Probe (TS155-R3).
To check for shorts, opens,
and split pairs, you won’t need the
remote. But to test for miswires
and reversals, you’ll need the
remote.
You can also use the tester
with the Network Probe to
generate a tone for testing.
The LANTest Pro CAT5e
Tester/Analyzer Kit includes eight
remotes for testing cable runs to
more than one endpoint. The
length range is 6 to 320 feet (1.8 to
Measure cable lengths and
find faults quickly for up to
eight cable endpoints.
Key Features
LANTEST AND LANTEST PRO CAT 5E TESTER/ANALYZERS
97.5 m) for both the LANTest and
LANTest Pro.
The tester includes a 9-V
alkaline battery and operates in
four modes:
• Cable testing mode. With no
remote attached, the
LANTest checks for shorts,
opens, and split pairs. When
the remote is attached, the
LANTest also checks for
miswires and reversals.
• Length measurement mode.
Measure the length of a
cable in auto select, or
choose each pair to
measure length individually.
Adjust the cable parameter
by the capacitance per unit
length value, or by a known
length of cable.
• Setup mode. Select either
shielded twisted-pair (STP)
cable or unshielded twistedpair (UTP) cable. Beeper
on/off and units of measure
are also selectable
variables.
• Tone generator mode.
Select individual wires and
pairs to carry a tone. To
trace tones, you’ll also need
to order the Network Probe.
Here’s how it works:
Suppose you have a jumble
of cables in a wiring closet.
One of these cables runs to
a nearby office. To find the
other end of the office cable
in the closet, you can use
the tester to generate a tone.
Then, when you wave the
Network Probe near the
bundle of cables, the probe
will beep when it locates the
desired cable.
When you need to find cable
length, test for shorts, opens,
miswires, reversals, and split
pairs, or trace cable, choose the
LANTest CAT5e Tester/Analyzer.
If you need additional remotes to
test multiple cable runs, select the
LANTest Pro CAT5e Tester/
Analyzer Kit.
2
LANTest CAT5e Tester/Analyzer (TS870A)
• (1) LANTest main unit
• (1) remote unit
• (2) 1-ft. (0.3-m) jumper cables
• (1) 9-V alkaline battery
• (1) carrying case
• (1) users’ manual
LANTest Pro CAT5e Tester/Analyzer Kit (TS875A)
• (1) LANTest main unit
• (8) remote units
• (2) 1-ft. (0.3-m) jumper cables
• (1) RJ-45 to (2) alligator clips cable
• (2) RJ-45 to F coax adapters
• (1) 9-V alkaline battery
• (1) carrying case
• (1) users’ manual
Cable Test Lengths:
Maximum: 320 ft. (97.5 m);
Minimum: 6 ft. (1.8 m)
Cable Types: Shielded or
unshielded CAT3, CAT4, CAT5,
CAT5e; coax (with adapters
attached)
Switch: To prevent the
20-second
“no activity” power off,
periodically press the “fault
check/tone” switch
Typical Alkaline Battery Life:
Cable Testing: 120 hours (times
are for the full capacity of the
battery used continuously in
cable testing mode)
Connectors: TS870A, TS875A:
(1) RJ-45 female
Temperature: Operating: 32 to 122°F
(0 to 50°C);
Storage: -4 to +158°F (-20 to
+70°C)
Humidity: 10 to 90%,
noncondensing
Power: (1) 9-V alkaline battery
Size: 5.7"H x 2.9"W x 1.2"D (14.5 x
7.4 x 3 cm)
Weight (with battery installed):
0.4 lb. (0.2 kg)
What’s Included
Specifications
Ordering Information
ITEM CODE
For testing cable to a single point, order…
LANTest CAT5e Tester/Analyzer (1 Remote).........TS870A
For multipoint testing, order…
LANTest Pro CAT5e Tester/Analyzer Kit
(8 Remotes) ...............................................................TS875A
For tracing tones, order…
Network Probe..........................................................TS155-R3
Recognize any of these
situations?
• You wait more than 30
minutes to get through to a
vendor’s tech support.
• The so-called “tech” can’t
help you or gives you the
wrong answer.
• You don’t have a purchase
order number and the tech
refuses to help you.
• It’s 9 p. m. and you need help,
but your vendor’s tech
support line is closed.
According to a survey by Data
Communications magazine, 90%
of network managers surveyed
say that getting the technical
support they need is extremely
important when choosing a
vendor. But even though network
managers pay anywhere from 10
to 20% of their overall purchase
price for a basic service and
support contract, the technical
support and service they receive
falls far short of their
expectations—and certainly isn’t
worth what they paid.
At Black Box, we guarantee
the best value and the best
support. You can even consult our
Technical Support Experts before
you buy if you need help selecting
just the right component for your
application.
Don’t waste time and
money—call Black Box today.
Why Buy From Black Box? Exceptional Value.Exceptional Tech Support.Period.
Loading...