Blackbox LIG1014A, LIG1082A, LIG1080A Quick Start Manual

STEP X - Name of Step

24/7 TECHNICAL SUPPORT AT 877.877.2269 OR VISIT BLACKBOX.COM

LIG1014A, LIG1080A, LIG1082A

INDUSTRIAL
SWITCH

QUICK START GUIDE

STEP 1 - Hardware Description

LIG 1014 A

TABLE 1. COMPONENTS

COMPONENT LIG1014A LIG1080A LIG1082A

RJ-45 ports 10 8 6

SFP cages 4 None 2

P1 LED 1 1 1

P2 LED 1 1 1

ALM LED 1 1 1

Ethernet Port Link LED 10 8 6

Ethernet Port Speed LED 10 8 6

SFP Port Link LED 4 None 2

SFP Port Speed LED 4 None 2

LIG1082A

LIG 108 0A

STEP 2 - What's Included

WHAT'S INCLUDED

• (1) INDUSTRIAL MANAGED GIGABIT
ETHERNET SWITCH

• (2) WALLMOUNT PLATES

• (1) DIN RAIL CLIP

• (1) DC POWER TERMINAL BLOCK

• RJ-45 PORT DUST COVERS

• SFP PORT DUST COVERS

• THIS QUICK START GUIDE

TABLE 2. LED STATUS INDICATORS

LED NAME STATUS DESCRIPTION

P1/P2

ON Green P1/P2 power line has power

OFF P1/P2 power line is disconnected or does not have power

Alarm

ON Red Ethernet link fails, alarm or power failure alarm occurs

OFF No Ethernet link fails and no power failure alarm

Copper port Link/Act

ON Green Ethernet link up but no traffic is detected

Flashing Green Ethernet link up and traffic is detected

OFF Ethernet link down

Copper port Speed

ON Yellow A 1000-Mbps connection is detected

OFF No 1000-Mbps link, a 10-Mbps or 100-Mbps connection is detected

SFP port Link/Act

ON Green Ethernet link up

OFF Ethernet link down

SFP port Speed

ON Yellow SFP port speed 1000-Mbps connection is detected

OFF No link or an SFP port speed 100-Mbps connection is detected

STEP 3A - Install on DIN Rail

INSTALL THE UNIT ON A DIN RAIL

1. Attach the screws to the DIN clip.

2. Hook the unit onto the DIN rail.

3. Push the bottom of the unti towards the DIN
rail until it locks into place.

+

+

+

+

+

+

+

+

+

+

+

+

+

+

+

+

STEP 3B - Mount on a Wall

INSTALL THE UNIT ON A WALL

1. Attach the screws to the wallmount brackets.

2. Using M4 screws, attach the unit and bracket
assembly to the wall.

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

1

P1

P2

ALM

2

3

4

5

6

7

8

9 10

–

–

–

–

–

–

–

–

–

–

–

–

–

–

STEP 4A - Connect the RJ-45 Ethernet Interface

CONNECT THE SWITCH TO PC OR DEVICE

1. To connect the switch to a PC, use a straight­through Ethernet or crossover cable.

2. To connect the switch to an Ethernet device,
use unshielded twisted-pair (UTP) or shielded
twisted-pair (STP) Ethernet cables.

NOTE: The pin assignments of the 10BASE-T,
100BASE-TX and 1000BASE-T connector
(RJ-45) are shown in the diagram at right
and the table below.

TABLE 3. 10/100/1000 PORT PINOUTS

PIN REGULAR PORTS

1 TP0+

2 TP0 -

3 TP1 +

4 TP2 +

5 TP2 -

6 TP1 - -

7 TP3 +

8 TP3 -

8 7 6 5 4 3 2 1

STEP 4B - Connect the Fiber SFP Ethernet Interface

1001000BASE-FX CONNECTIONS

For both 100/1000 Mbps fiber speed
connections, the SFP slots are available.
The SFP slot accepts the SFP transceivers
shown in the table below.

DANGER! Never look directly at optical
connectors that might be emitting optical
energy. YOUR EYES MIGHT BE DAMAGED!

TABLE 4. COMPATIBLE SFPS

PART NUMBER DESCRIPTION

LFP411 SFP/1250 Extended Diagnostics, LC multimode, 850 nm, 550 m

LFP412 SFP/1250 Extended Diagnostics, LC multimode, 1310 nm, 2 km

LFP413 SFP/1250 Extended Diagnostics, LC single-mode, 1310 nm, 10 km

LFP414 SFP/1250 Extended Diagnostics, LC single-mode, 1310 nm, 40 km

LFP401 SFP/155 Extended Diagnostics, LC multimode, 850 nm, 2 km

LFP403 SFP/155 Extended Diagnostics, LC single-mode, 1310 nm, 30 km

LFP404 SFP/155 Extended Diagnostics, LC single-mode, 1310 nm, 60 km

LFP402 SFP/155 Extended Diagnostics, LC multimode, 1310 nm, 2 km

LFP418 SFP/1250 Extended Diagnostics, LC single-mode, 1550 nm, 80 km

LFP420 Simplex SFP/1250, Extended Diagnostics, single-mode, 1550 nm TX, 1310 nm RX

STEP 5 - Connect the Power

ALARM RELAY AND GROUND

The alarm relay output contacts are in the
middle of the DC terminal block connector
as shown in the diagram below.

The alarm relay out is “Normal Open” and will
close when it detects a power or Ethernet
link failure.

The relay has a current carrying capacity
of 0.5 A at 24 VDC.

CONNECTING POWER TERMINAL BLOCK

The switch can be powered from two DC power
supplies (input range 12 VDC to 58 VDC).

1. Insert the positive and negative wires into
the V+ and V- contacts on the terminal block.

2. Tighten the wire clamp screws to prevent
the wires from becoming loose.

PWR1

CONSOLE

RESET

+ – – +

+

ALM PWR2

12–48 VDC POWER INPUT

GROUND

1

1

2

3 (RD)

4 (TD)

5

6 (DGND)

7

8

6

7

4

8

9

3

TD

2

RD

5

DGND

STEP 6 - Connect the Console Port

CONSOLE CONNECTION

Use the console port to manage the switch
locally via a terminal emulator or a computer
with terminal emulation software.

Connect the switch's DB9 connector to a
computer's COM port with the following
properties:

• Baud rate: 115200 bps

• 8 data bits

• 1 stop bit

• No Priority

• No Flow Control

To connect the host PC to the console port,
you need an RJ-45 male to RS-232 DB9 female
connector cable.

1. Connect the RJ-45 end of the cable to the
switch‘s console port.

2. Connect the DB9 end of the cable to the
PC's COM port.

STEP 7 - Connect and Login to the Switch

CONNECT TO THE ETHERNET PORT

1. Connect to the Ethernet port of the

managed switch.

Factory Default IP: 192.0.2.1

2. Log in with the default username
and password:

Username: admin

Password: (blank) (Just press the Enter key.)

OPTIONAL: DOWNLOAD USER MANUAL

For product specifications and regulatory
information, refer to the User Manual. You can
download this document from our web site.

1. Go to www.blackbox.com

2. Enter the part number (LIG1014A, LIG1080A
or LIG1082A) in the search box.

3. Click on the product in the “Product
Results” page.

4. Click on the “Support” tab on the product page,
and select the document you wish to download.

If you have any trouble accessing the Black Box
site to download the manual, you can contact
our Technical Support at 877-877-2269
or [e-mail].

STEP 8 - CLI Initialization and Configuration (Optional)

COMMAND-LINE INTERFACE (CLI)

1. Connect to the Ethernet port of the

managed switch.

2. Type in the command: telnet 192.0.2.1

3. Log in with the default username
and password:

Username: admin

Password: (none) (Just press the Enter key.)

4. Change the IP with the commands
listed below.

CLI command:

enable
configure terminal
interface vlan 1
ip address xxx.xxx.xxx.xxx.xxx.xxx.xxx.xxx
exit

STEP X - Name of Step

COPYRIGHT 2018 BLACK BOX CORPORATION. ALL RIGHTS RESERVED.