Page 1
LH3000
LH3001
PCI-E Network Adapter, 2-Port, 10-GbE
Quick Installation Guide
Has (2) RJ-45 10-GbE ports or (2) SFP+ 10-GbE ports.
To download the most recent drivers for the adapter, go to
blackbox.com, enter LH3000 or LH3001 in the search box, click on
the “Resources” tab, then select the item you wish to download.
Customer
Support
Information
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S.
call 724-746-5500) • FREE technical support 24 hours a day, 7 days
a week: Call 724-746-5500 or fax 724-746-0746 • Mailing address:
Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Web site: www.blackbox.com • E-mail: info@blackbox.com
Page 2
PCI-E Network Adapter Quick Installation Guide
Quick Installation Guide
CAUTION: Turn off and unplug the power before removing the computer’s cover.
Failure to do so could endanger you and may damage the adapter or
computer.
STEP 1.
Turn off the computer and unplug the power cord. For hot-plug servers, see your
server documentation first.
STEP 2.
Remove the cover bracket from a PCI-Express slot (v1.0a or newer) or a PCI (2.2 or
later) slot. If you have configuration problems, see your computer's documentation
to determine if the PCI-Express or PCI slots are bus master-enabled.
STEP 3.
NOTE: This is an optional step for low-profile-capable models:
If you need to install the adapter in a low profile PCI-Express or PCI chassis, first
replace the adapter standard bracket with the supplied low-profile bracket. To
remove the existing bracket, unscrew the two screws as shown in the diagram on
the next page and then pull the bracket off. Reverse the process to attach the low
profile bracket.
Page 2
724-746-5500 | blackbox.com
Page 3
PCI-E Network Adapter Quick Installation Guide
STEP 4.
Firmly insert the adapter into the selected slot. Push down to ensure the adapter
is fully seated. If you install the adapter in a PCI-Express or PCI slot, make sure
the exposed end of the connector does not touch any part of the motherboard.
Secure the bracket to the chassis.
STEP 5.
Replace the computer cover and plug in the power cord.
724-746-5500 | blackbox.com Page 3
Page 4
PCI-E Network Adapter Quick Installation Guide
STEP 6.
Connect the network cable. The copper model (LH3000) is shown below. The fiber
model (LH3001) installs in a similar way, but it has fiber SFP+ slots that accept an
SFP+ module and attaches to fiber cable via the module’s fiber connectors.
LH3000 (copper model):
• For 10-Gbps operation (10GBASE-T), use category 6 or better cable with 4-pair
wiring, different pitches).
• Insert the twisted-pair, RJ-45 network connector as shown.
• For 1000-Mbps operation (100BASE-T), use Category 5 or better cable with 4-pair
wiring.
• For 100-Mbps operation (100BASE-TX), use Category 5 or better cable.s
NOTES:
1. Maximum length is 328 feet (100 meters).
2. The adapter must be connected to a compatible link partner that has the same
configuration.
Page 4
724-746-5500 | blackbox.com
Page 5
PCI-E Network Adapter Quick Installation Guide
LH3001 (fiber model):
• For the SFP+ slot, remove and save the fiber optic connector cover. Insert a
matching fiber optic connector module into the SFP+ slot on the adapter.
The table below lists the compatible SFP+ modules:
Compatible SFP+ modules
Product Code Description
LSP422 10GBASE-SR SFP+, 1310-nm Single-Mode, 10 km, LC
LSP421 10GBASE-SR SFP+, 850-nm Multimode, 300 m, LC
NOTE: For LC adapters, converter patch cables are available to allow plugging into
an SC type connector.
• Most connectors and ports are keyed for proper orientation. If the cable you are
using is not keyed, check to be sure the connector is oriented properly.
STEP 7.
Install the adapter drivers.
• Start the computer.
NOTE: You must have administrative rights to the operating system to install the
drivers.
• For Windows
®
2000, XP, Windows 7, Vista®, Server 2003, and Server 2008, the
adapter is detected and Windows either installs a resident driver or starts the
“Found New Hardware” wizard. If a resident driver installs (wizard does not
appear), update the driver by inserting the cover-mounted CD.
®
• For Windows NT 4.0, Linux, NetWare
, UnixWare, FreeBSD, and other operating
systems: Refer to the driver link on the “Resources” tab (described on the next
page)
724-746-5500 | blackbox.com Page 5
Page 6
PCI-E Network Adapter Quick Installation Guide
To download the latest software drivers or this quick installation guide from
the Web site:
1. Go to www.blackbox.com
2. Enter LH3000 or LH3001 in the search box:
3. Click on the “Resources” tab on the product page, and select the drivers and/or
documents you wish to download.
Ethernet Address
The Port A Ethernet address is printed on the bar code label on the adapter. Add
one hexadecimal to this value to obtain the next port address. For example, Port B
would be 0002B3002B51, Port C would be 0002B3002B52, and Port D would be
0002B3002B53.
Page 6
724-746-5500 | blackbox.com
Page 7
PCI-E Network Adapter Quick Installation Guide
LEDs on the Adapter
ACT/LNK
10/100/1000
ACT/LNK
10/100/1000
724-746-5500 | blackbox.com Page 7
Page 8
Chapter
Black Box Tech Support: FREE! Live. 24/7.
Tech support the
way it should be.
Great tech support is just 60 seconds away
at 724-746-5500 or blackbox.com.
About Black Box
Black Box provides an extensive range of networking and infrastructure products.
You’ll find everything from cabinets and racks and power and surge protection
products to media converters and Ethernet switches all supported by free, live 24/7
Tech support available in 60 seconds or less.
© Copyright 2014. Black Box Corporation. All rights reserved. Black Box® and the Double Diamond
logo are registered trademarks of BB Technologies, Inc. Any third-party trademarks appearing in
this manual are acknowledged to be the property of their respective owners.
LH3000, Quick Start Guide, version 1
Page 900
724-746-5500 | blackbox.com
Loading...