Black Box LGH1006A Quick Start Manual

Page 1
724-746-5500 | blackbox.com724-746-5500 | blackbox.com 724-746-5500 | blackbox.com
Page 5 Page 6
© Copyright 2016. Black Box Corporation. A ll rights reserved. Black Box and the Double Diamond log o are registered trademarks of BB Technologies, I nc. Any other trademarks mention ed in this manual are acknowledged to be the property of the tra demark owner s.
lgh1006a_qsg_rev1
Quick Start Guide
LGH1006A Industrial Ethernet Switch
LGH10 06A
Black Box Tech Support: FREE! Live. 24 /7. Tec h supp ort the way it should be.
Great tech support is just 60 seconds away at 724-746-5500 or blackbox.com.
Order toll-free in the U.S.: Call 877- 877-BBOX (outside U.S. call 1-724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746 - 0746
Web site: www.blackbox.com
E-mail: info@blackbox.com
Customer
Support
Information
LGH1006A Quick Start Guide
What’s Included
Your package should include the following items. If anything is missing or damaged, contact Black Box Technical Support at 724-746-5500 or info@blackbox.com.
• (1) LGH1000 Series Industrial Ethernet Switch ­(4) 10/100/1000-Mbps, (2) GE SFP
• (1) 6-pin terminal block
• (4) RJ-45 dust covers
• (2) SFP slot dust covers
• (3) M3 round screws
• (2) wall mount brackets and hardware
• (1) DIN rail
• This Quick Start Guide
Specifications
Approvals
Ethernet Standards IEEE 802.3 for 10BA SE-T
IEEE 802.3u for 100 BASE-TX and 100BASE -FX IEEE 802.3ab for 10 00BA SE-T IEEE 802.3z for 100 0BASE-X IEEE 802.3x for F low control
EMI FCC Part 15, CISPR (EN 55022) class A
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS),
EN61000-4 -4 (EFT ), EN61000-4 -5 (Surge), EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
Shock IEC60 068-2-27
Free Fall IEC60 068-2-32
Vibration IEC60 068-2- 6
Safety EN60950-1
Environmental
Operating Temperature -40 to +158° F (- 40 to +70° C)
Storage Temperature -40 to +185° F (- 40 to +85° C)
Operating Humidity 5 to 95%, noncon densing
Performance
MAC Table 1K MAC addresses
Processing Store-and-Forward
Physical
Connectors (4) 10/ 100 /1000BA SE-T(X ) RJ -45,
auto-MDI/ MDI-X ports, (2) 100/1000BASE-X SFP ports
Enclosure IP-30
Dimensions 5.68"H x 1.03"W x 3.74"D
(14.43 x 2.61 x 9.49 cm)
Weight 0.9 lb. (0.41 kg)
Indicators (2) Power LE Ds:,
(1) Fault LED, (4) 10/10 0/100 0BASE-T (X) RJ -45 Port LEDs, (2) 100/ 1000BA SE-X SFP por t LEDs
User Controls
SFP Speed D IP switche s 1 and 2 (for por ts 5 and 6)
DIP Switch O N: SFP spe ed is set to 100 Mb ps, DIP Switch O FF: SFP spee d is set to 1000 Mbps
Relay Output DIP switches 1 and 2 (for Power 1 an d Power 2 por ts)
DIP Switch 1: Pow er 1 failed warni ng, DIP Switch 2: P ower 2 failed war ning
Specifications (continued)
Power
Input (2) 12–48 VD C inputs on 6 -pin terminal block
Consumption 6.4 W (power ed device not in cluded)
Overload Current Protection Present
Reverse Polarity Protection Present
Fault Contact Relay Output 1 A at 24 VDC
Page 2
724-746-5500 | blackbox.com724-746-5500 | blackbox.com 724-746-5500 | blackbox.com
LGH1006A Quick Start Guide
Table 3. Power DIP switches
for PWR-1 and PWR-2.
Power DIP Sw itch
Settings
Description
PWR 1 PWR 2
OFF OFF Power failure relay alarm disabled
ON OFF PWR-1 failure, relay alarm e nabled
OFF ON PWR-2 failure, re lay alarm enabl ed
ON ON PWR-1 or PWR -2 failure, relay alarm
enabled
Installation
Install the DIN rail or wallmount brackets on the switch as shown below.
Figure 3. DIN Rail or Wallmount brackets installation.
LGH1006A Quick Start Guide
Page 3Page 2 Page 4
Overview
The LGH1006A Industrial Ethernet Switch is an unmanaged Ethernet switch, with four 10/100/ 1000BASE-T(X) ports and two 100/1000BASE-X SFP ports. To set the optical network speed SFP port, change the settings of the DIP switch as described in Table 3-1. The operating temperature ranges from
-40 to +158° F (-40 to +70° C).
Features
• Provides four 10/100/1000BASE-T(X) ports.
• SFP port supports 100BASE-FX and 1000BASE-X dual speed.
• Switch supports auto-negotiation and auto-MDI / MDI-X.
• Uses store-and-forward transmission and flow control.
• Has IP-30 housing.
• Mounts on a DIN rail or on a wall.
Hardware Description
Figure 1. Front panel.
Table 1. Front panel components.
Component Description
(2) LEDs: P WR1, PWR2 Lights whe n correspon ding power por t is
adtive
(1) Power Fault LED Lights when the power fails
(2) SFP Link /Act LEDs Lights whe n there is act ibiy on the
corresponding port
(2) 100/1000BASE-T(X) SFP port
Lights whe n the port is o perating at 100 0 Mbps
(4) Gigab it LAN po rts Lights w hen the por t is operating a t 1000
Mbps
(4) Por t Link/ Act. LEDs Lights gr een when ther e is activit y on the port
(4) 100 -Mbps LE Ds Li ghts amber w hen the corres ponding por t is
operating at 10 0 Mbps
Table 2. SFP speed selection DIP switches
(for Ports 5 and 6.
SFP Spee d Selec tion DIP Switch Pos itions 1 and 2
Description
Both OFF 1000 Mbps
Both ON 100 Mbps
Power Connection Guide
Figure 2. Power connections.
LGH1006A Quick Start Guide
Attaching the
DIN rail brackets
Attaching the
wallmount brackets
Loading...