Black Box JPMT1024-ANG User Manual

45° Side-Exiting Multmedia Panel

Direction of

IDC slot

Black Box Tech
Support: FREE! Live.
24 / 7. Tech support
the way it should be.

JPMT1024-ANG

45° Side-Exiting Multimedia Panel

Angles ports
to the sides.

Figure 5. IDC slot position.

6. Secure the back cables with the supplied cable ties.

NOTE: Do not overtighten the cables.

7. Figure 6 shows a completed installation.

Figure 6. Completed patch panel installation.

Great tech support is just 30 seconds
away at 724-746-5500 or blackbox.com.

Customer

Support

Information

© Copyright 2011. Black Box Corporation. All rights reser ved.
Black Box and the Double Diamond logo are registered trademarks of
BB Technologies, Inc. Any other trademarks mentioned in this manual
are acknowledged to be the property of the trademark owners.

Order toll-free in the U.S.:
Call 877-877-BBOX
(outside U.S. call 1-724-746-5500)

FREE technical support
24 hours a day, 7 days a week:
Call 724-746-5500 or
fax [phone]

Mailing address:
Black Box Corporation
1000 Park Drive
Lawrence, PA 15055-1018

Web site: www.blackbox.com

E-mail: [e-mail]

Helps to reduce stress on the ports.
Horizontal cable management is not required.

1. Specifications

Size: Without rear base installed: 1.75”H (1U) x

19”W x 0.625”D (4.5 x 48.3 x 1.6 cm);
With rear base installed: 1.75”H (1U) x 19”W x
5”D (4.5 x 48.3 x 12.7 cm)

Weight: 1.5 lb. (0.7 kg)

2. Overview

2.1 Introduction

The 24-Port 45° Side-Exiting Multimedia Panel
angles ports to the sides, which helps reduce
stress on the ports and eliminates the need for
horizontal cable management. The rear of the
panel has an optional cable support bar that
provides support to horizontal cables accessing
the panel.

JPMT1024-ANG

JPMT1024-ANG, rev. 1

Page 5 Page 6

724-746-5500 | blackbox.com724-746-5500 | blackbox.com 724-746-5500 | blackbox.com

45° Side-Exiting Multmedia Panel 45° Side-Exiting Multmedia Panel45° Side-Exiting Multmedia Panel

2.2 What’s Included

Your package should include the following items.
If anything is missing or damaged, contact Black Box
Technical Support at 724-746-5500 or
[e-mail].

• (1) 45° Side-Exiting Multimedia Patch Panel

• (2) side brackets

• (1) rear cable bar

• (24) cable ties

• (4) 10-32 screws

• (4) 12-24 screws

• This user’s manual

3. Installation Steps

1. Mount the panel on a 19-inch rack, as shown
in Figure 1.

2. Attach each side bracket to the matching end of the
bar accordiing to the same marking. See Figure 2.

mark “R”

Slide in

Slide in

mark “L”

Figure 2. Attaching the side bracket.

3. Snap the rear cable bar into the patch panel, as
shown in Figure 3.

4. Load the wired keystone jack into the patch panel.
Make sure the locking knob is locked first before
sliding in the keystone jack or support fitting. See
Figure 4.

NOTE: Ports 1–6 and 13–18 share the same orienta-

tion, while ports 7–12 and 19–24 are placed
in opposite positions. Be sure to follow the
directions during installation.

NOTE: For best connector loading sequences, start

from the sides and install toward the center.

locking knob

latch

Figure 1. Mounting the panel on a rack.

Figure 3. Attaching the rear wire manager.

JPMT1024-ANG JPMT1024-ANGJPMT1024-ANG

Figure 4. Loading the keystone jack or support fitting.

5. Make sure the IDC slot of the keystone jack faces
toward the center of the patch panel, as shown in
Figure 5.

Page 3Page 2 Page 4

724-746-5500 | blackbox.com724-746-5500 | blackbox.com 724-746-5500 | blackbox.com