CUSTOMER
SUPPORT
INFORMATION
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Web site: www.blackbox.com • E-mail: info@blackbox.com
AUGUST 2002
IS290A
Autosensing ISDN Matrix Switch
1
FCC AND IC RFI STATEMENTS
FEDERAL COMMUNICATIONS COMMISSION
AND
INDUSTRY CANADA
RADIO FREQUENCY INTERFERENCE STATEMENTS
This equipment generates, uses, and can radiate radio-frequency energy, and if not
installed and used properly, that is, in strict accordance with the manufacturer’s
instructions, may cause interference to radio communication. It has been tested
and found to comply with the limits for a Class A computing device in accordance
with the specifications in Subpart B of Part 15 of FCC rules, which are designed to
provide reasonable protection against such interference when the equipment is
operated in a commercial environment. Operation of this equipment in a
residential area is likely to cause interference, in which case the user at his own
expense will be required to take whatever measures may be necessary to correct
the interference.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emission from
digital apparatus set out in the Radio Interference Regulation of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le
brouillage radioélectrique publié par Industrie Canada.
2
AUTOSENSING ISDN MATRIX SWITCH
FCC Requirements for
Telephone-Line Equipment
1. The Federal Communications Commission (FCC) has established rules which
permit this device to be directly connected to the telephone network with
standardized jacks. This equipment should not be used on party lines or coin
lines.
2. If this device is malfunctioning, it may also be causing harm to the telephone
network; this device should be disconnected until the source of the problem
can be determined and until the repair has been made. If this is not done, the
telephone company may temporarily disconnect service.
3. If you have problems with your telephone equipment after installing this
device, disconnect this device from the line to see if it is causing the problem.
If it is, contact your supplier or an authorized agent.
4. The telephone company may make changes in its technical operations and
procedures. If any such changes affect the compatibility or use of this device,
the telephone company is required to give adequate notice of the changes.
5. If the telephone company requests information on what equipment is
connected to their lines, inform them of:
a. The telephone number that this unit is connected to.
b. The ringer equivalence number.
c. The USOC jack required: RJ-11C.
d. The FCC registration number.
Items (b) and (d) can be found on the unit’s FCC label. The ringer
equivalence number (REN) is used to determine how many devices can be
connected to your telephone line. In most areas, the sum of the RENs of all
devices on any one line should not exceed five (5.0). If too many devices are
attached, they may not ring properly.
6. In the event of an equipment malfunction, all repairs should be performed by
your supplier or an authorized agent. It is the responsibility of users requiring
service to report the need for service to the supplier or to an authorized
agent.
3
CERTIFICATION NOTICE FOR EQUIPMENT USED IN CANADA
Certification Notice for
Equipment Used in Canada
The Industry Canada label identifies certified equipment. This certification means
that the equipment meets certain telecommunications-network protective,
operation, and safety requirements. Industry Canada does not guarantee the
equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be
connected to the facilities of the local telecommunications company. The
equipment must also be installed using an acceptable method of connection. In
some cases, the company’s inside wiring associated with a single-line individual
service may be extended by means of a certified connector assembly (extension
cord). The customer should be aware that compliance with the above conditions
may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized maintenance
facility—in this case, Black Box. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines, and internal metallic water pipe
system, if present, are connected together. This precaution may be particularly
important in rural areas.
CAUTION
Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or
electrician, as appropriate.
The LOAD NUMBER (LN) assigned to each terminal device denotes the
percentage of the total load to be connected to a telephone loop which is used by
the device, to prevent overloading. The termination on a loop may consist of any
combination of devices, subject only to the requirement that the total of the load
numbers of all the devices does not exceed 100.
4
AUTOSENSING ISDN MATRIX SWITCH
NORMAS OFICIALES MEXICANAS (NOM)
ELECTRICAL SAFETY STATEMENT
INSTRUCCIONES DE SEGURIDAD
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de
que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para
referencia futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de
operación deben ser respetadas.
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca
de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc..
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que
sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea
recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá
a lo descrito en las instrucciones de operación. Todo otro servicio deberá ser
referido a personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no
interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá,
alfombra o superficie similar puede bloquea la ventilación, no se debe colocar
en libreros o gabinetes que impidan el flujo de aire por los orificios de
ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor
como radiadores, registros de calor, estufas u otros aparatos (incluyendo
amplificadores) que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del
tipo descrito en el instructivo de operación, o como se indique en el aparato.
5
NOM STATEMENT
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización
del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no
sean pisados ni pellizcados por objetos colocados sobre o contra ellos,
poniendo particular atención a los contactos y receptáculos donde salen del
aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las
recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas
de energia.
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea
usado por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean
derramados sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en su
desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
6
AUTOSENSING ISDN MATRIX SWITCH
TRADEMARKS USED IN THIS MANUAL
UL is a registered trademark of Underwriters Laboratories Incorporated.
Any other trademarks mentioned in this manual are acknowledged to be the property of the
trademark owners.
7
CONTENTS
Contents
Chapter Page
1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2. Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.2 What the Package Includes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.3 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.4 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3. Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4. Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.1 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.2 User Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3 Manual Mode Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5. RS-232 Interface Program. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.2 Communication Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.3 Setup Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.3.1 Mode of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.3.2 Selection Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.3.3 Current Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.3.4 Exiting the Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Appendix. Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
A.1 Calling Black Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
A.2 Shipping and Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8
AUTOSENSING ISDN MATRIX SWITCH
1. Specifications
Compliance: FCC Class A, CE, UL
®
Connectors: Input: (3) 8-pin RJ-45 female; Output: (12) 8-pin RJ-45 female;
RS-232 Input: (1) DB9 connector for serial communication (manual mode only);
(1) power connector
Interface: Input: (3) BRI (Basic Rate Interface) ISDN T interfaces to be connected
to NT1s (Network Terminal 1); Output: (12) BRI (Basic Rate Interface) ISDN S
interfaces to be connected to TEs (Terminal Equipment)
User Controls: Keypad: 13 front-panel keys; Computer: RS-232 serial
communication, DB9 female connector (RS-232 input has first priority; when the
RS-232 input is used, the keypad on the ISDN Matrix Switch is disabled for the
duration of the PC command)
Display: (1) Front-panel 16-character LCD display
Indicators: (1) LED: Power
Enclosure: Aluminum, dark gray, medium-texture finish
Power: 110 VAC/60 Hz or 220 VAC/50 Hz
Size: 1.6"H x 17"W x 8.5"D (4.1 x 43.2 x 21.6 cm)
Weight: 4.5 lb. (2 kg)
9
CHAPTER 2: Introduction
2. Introduction
Use the Autosensing ISDN Matrix Switch for switching and routing BRI (Basic Rate
Interface) ISDN lines.
2.1 Features
• Simple and quick switching of ISDN BRI lines.
• Instantly “move” BRI lines.
• Routes three ISDN lines to twelve possible outputs.
• Three modes of operation for manual, 128-kbps automatic, or 384-kbps
automatic switching.
• RS-232 controllable.
• Front-panel keypad control.
• On-demand automatic line routing and re-routing (user-selectable).
• LCD readout of active line pairing reflects current input and output
assignments.
• Active Data Lock—The ISDN Matrix Switch locks any routing command that
involves an active line until the call has been disconnected.
2.2 What the Package Includes
You should have received the following items:
• (1) Autosensing ISDN Matrix Switch
• (1) Power cord
• (1) 3.5" diskette containing RS-232 interface software
• This users’ manual
10
AUTOSENSING ISDN MATRIX SWITCH
2.3 Front Panel
Figure 2-1. The front panel.
Power: The red LED lights when the switch is powered.
Keypad: Use the 13 keys to change the switch’s settings.
LCD panel: The 16-character display shows the current input and output
assignments, line busy status, keypad entries, and error messages.
2.4 Rear Panel
Figure 2-2. The rear panel.
AC In: AC power input module. It contains the AC inlet connector, fuse,
and line-voltage selector. The line-voltage selector allows the switch to operate
on either 110-VAC or 220-VAC power.
RS-232 input: The DB9 female connector is used for serial communication
(manual mode only).
Outputs: Twelve 8-pin RJ-45 female connectors to be connected to TEs
(Terminal Equipment) via twisted-pair cable.
Inputs: Three 8-pin RJ-45 female connectors to be connected to NT1s
(Network Terminal 1) via twisted-pair cable.
❼
❻
❺
❹
❸
❷
❶
❹
❺
❼
❻
❶
❷
❸
11
CHAPTER 3: Setup
3. Setup
1. Make sure the line-voltage selector is set to match the AC power available in
your area. The LCD display indicates the current setting. To change the
voltage setting, pry open the cover of the AC inlet using a small flat-head
screwdriver. Take the voltage selector out and re-insert it in the appropriate
direction. The desired VAC label on the voltage-selector switch should be
pointing toward the cover. Do not try turning the voltage-selector switch while
it is in the module.
2. Connect the necessary inputs to the NT1s using straight-through twisted-pair
cable.
3. Connect the necessary outputs to the videoconferencing equipment using
straight-through twisted-pair cable.
4. If you want to control the switch using a computer, the RS-232 port on the
Autosensing ISDN Matrix Switch must be connected to the serial port of the
PC via a serial cable (not included).
5. Plug in the AC power cord and check for the Power LED.
6. The LCD module should display OUTPUT:00 00 00.
7. The unit is now operational. Make the appropriate connections using either
the keypad or the computer.
Figure 3-1. Typical setup configuration.
Termnation 384
kbps
384
kbps
384
kbps
384
kbps
12
AUTOSENSING ISDN MATRIX SWITCH
4. Operation
4.1 Modes of Operation
The Autosensing ISDN Matrix Switch has three modes of operation: Mode 0,
Mode 1, and Mode 3.
M
ODE
0—M
ANUAL
• Upon powerup, it’s the default mode.
• The keypad and RS-232 are fully functional. Consult Section 4.3 for more
information.
M
ODE
1—128
KBPSAUTOSENSE
(1 BRI L
INE
)
• Only Input 1 is used; Input 2 and Input 3 are ignored.
• Limited keypad and RS-232 control.
• Every two seconds the switch scans the outputs in ascending order (this is also
the output priority*):
Output 1➔Output 2➔…Output 11➔Output 12
*Unless there’s a line busy indication on the current output, in which case it
has the highest priority and cannot be switched away.
• Under no line busy conditions, if an activation signal is detected on one of the
outputs, the switch stops scanning the rest of the outputs. If the detected
output is not the same as the current output, the switch makes the appropriate
connection. However, if a signal is not detected on any of the 12 outputs, the
switch returns to its default configuration.
M
ODE
3—384
KBPSAUTOSENSE
(3 BRI L
INES
)
• Limited keypad and RS-232 control.
• Every two seconds the switch scans the outputs in ascending order:
Output 1➔Output 2➔…Output 11➔Output 12
13
CHAPTER 4: Operation
• Under no line busy conditions, if an activation signal is detected on one of the
outputs, the switch stops scanning the rest of the outputs. It determines the
group number, and if it is different than the current group number, the switch
makes the appropriate connections. However, if a signal is not detected on any
of the 12 outputs, the switch returns to its default configuration.
• The 12 outputs are divided into four groups in the following manner:
Group 1: Outputs 1, 2, and 3
Group 2: Outputs 4, 5, and 6
Group 3: Outputs 7, 8, and 9
Group 4: Outputs 10, 11, and 12
• Group priority is defined in the following way*:
Group 1➔Group 2➔…Group 3➔Group 4
*Unless there’s a line busy indication in one of the groups, in which case that
group has the highest priority and cannot be switched away.
4.2 User Instructions
When the Autosensing ISDN Matrix Switch is powered, the LCD displays the
following:
OUTPUT:00 00 00
This indicates that all of the inputs are disconnected (none of the three inputs are
connected to any of the outputs).
To select a mode, press the appropriate number key ( , , or ) on the
keypad. Pressing the key displays the current mode setting.
By pressing the key, the LCD displays: MANUAL MODE?
By pressing the key, the LCD displays: 1LINE AUTO MODE?
By pressing the key, the LCD displays: 3LINE AUTO MODE?
14
AUTOSENSING ISDN MATRIX SWITCH
To acknowledge the request, press the key; otherwise, to cancel the request, press the
key. Pressing any other key will result in FORMAT ERROR. However, if there is
videoconferencing in progress (indicated by a star in front of the lines being used)
then you can’t change the switch’s operating mode. Attempting to do so will result
in the LCD displaying LINE BUSY and the request will be ignored.
When the switch is not in manual mode, control of the keypad and RS-232 is
severely disabled. The only functioning keys on the keypad are the following: ,
, , , and . These keys are used to switch modes when there’s no
line busy indication. can also be used to check the current mode setting.
Pressing any other key will display the warning IN AUTO MODE!. Similar
limitations exist for the RS-232 control. See Section 5.3 for more information.
4.3 Manual Mode Instructions
Making or changing connections in manual mode (using the keypad) is quite easy.
Follow the five steps listed below.
• Step 1: Press the key. The LCD displays IN.
• Step 2: Press the input number key. The only valid keys are , , or .
The input number must be entered as a single digit. The LCD displays
IN (#).
• Step 3: Press the key. The LCD displays IN (#) OUT.
• Step 4: Press the output number key(s). The only valid keys are through
. Numbers that are less than ten can be entered directly as a single digit
(for example, 8) or as a double digit, where the number is preceded by a zero
(for example, 08). To select outputs 10 through 12, the key should be
pressed followed by the , , or key. The LCD displays either IN (#)
OUT (#) or IN (#) OUT(##).
• Step 5: Press . This will execute the command. The LCD displays either IN
(#) OUT (#) ENTER or IN (#) OUT (##) ENTER.
15
CHAPTER 4: Operation
NOTES
1. Unless you press a key on the keypad, the LCD displays the current
status: OUTPUT: ## ## ##.
2. If a valid key is pressed, the LCD displays the keypad entry for two
seconds. If the next valid key is not pressed within this time duration,
the LCD switches back to displaying the current status. However, the
previously entered information is not lost. The switch will save the
current partial valid keypad entry for 30 seconds. If more than 30
seconds have elapsed since a valid key was pressed, the switch erases
the partial entry from memory. As a result, you must start all over again.
3. The key also functions as a clear key. When the key is
pressed, the partial entry is erased from memory and the LCD is cleared
for two seconds. However, if the key is pressed while the entry
memory is blank, the LCD will display In, meaning that it’s the
beginning of a new valid entry.
4. Error messages are displayed for only two seconds.
5. If an invalid key is pressed, the LCD displays FORMAT ERROR and the
partial entry is erased from memory. Format Error is a syntax error that
occurs when the user deviates from the two valid keypad entry formats
( # # or # ## ). Either the entry sequence is
wrong or the numbers are out of range. It can also occur for invalid
mode selection.
6. Only one input can be connected to each output. If you try to connect
an input to an output that is already taken, the LCD displays OUTPUT
TAKEN and ignores the request. The only valid output that all three
inputs can share is 0, the disconnect state. Entering 0 or 00 as the
output number for any of the three inputs disconnects the input.
7. The Autosensing ISDN Matrix Switch is safeguarded to ensure no
disruption of video transmission. Data Lock eliminates any chance of
call disconnection by “locking” active lines so that no command can
interrupt current calls. If you try to disconnect or re-route an input on
which a call is in progress, the LCD displays LINE BUSY and disregards
the request. In addition, if a particular line is busy, the LCD displays a
star in front of the corresponding output when showing the current
status. The line busy status indicator on the LCD is updated every two
seconds.
16
AUTOSENSING ISDN MATRIX SWITCH
5. RS-232 Interface Program
5.1 Description
The RS-232 port on the Autosensing ISDN Matrix Switch is a DB9 female
connector. The RS-232 port must be connected to the serial port of the PC via a
straight-through serial cable (not included). You will need a PC—not a dumb
terminal—to use the RS-232 Interface software with the serial port. This product
will not work with terminal emulation software such as HyperTerminal or other
common terminal emulation software.
5.2 Communication Parameters
Before you install the software, make sure that your communication parameters
are set as follows: asynchronous, serial, 9600 baud rate, no parity bit, 1 start bit, 8
data bits, and 1 stop bit.
To access the ISDN Matrix Switch Controller 1.1 program, simply put the floppy
diskette into the disk drive and select ISDNBLACKBOX.EXE. This brings up the
screen shown in Figure 5-1.
Figure 5-1. ISDN Matrix Switch Controller 1.1 screen.
17
CHAPTER 5: RS-232 Interface Program
5.3 Setup Menu
You have four options that you can select from the Setup pull-down menu. These
options include Ports, Connect, Disconnect, and Exit.
When you select Ports, a screen appears that has the options COM 1, COM 2,
COM 3, and COM 4. Select the desired COM port.
5.3.1 M
ODE OFOPERATION
From the Setup menu, select Connect. Click on the items in the Mode Box to
change the operating mode of the Autosensing ISDN Matrix Switch. Select from
manual mode, 128 kbps automatic mode, or 384 kbps automatic mode.
5.3.2 S
ELECTIONBOX
Click on the options in the Selection Box to make/change a connection on the
Autosensing ISDN Matrix Switch.
From this screen, you can select which input ports are connected to the output
ports. For example, in the selection box shown on the screen, if you choose Input
1, then Output 3 and click the Connect button, input port 1 will connect to output
port 3. Continue selecting input and output port connections until all of the
desired port connections are made.
To disconnect ports, select the Disconnect option and click on the Disconnect
button.
Continue selecting port connections until you have connected or disconnected all
of the desired ports.
Click on the Clear button to clear the options from the screen.
Click on the Status button to check the status of the connected ports.
5.3.3 C
URRENTSTATUS
Items in the Current Status box display the current status of the Autosensing ISDN
Matrix Switch. It will reveal the current connections and the current operating
mode (manual, 128, or 384).
5.3.4 E
XITING THESETUPMENU
From the Setup menu, select Disconnect. This disconnects the switch’s RS-232
port. To exit the Setup menu, select Exit from the pull-down menu.
18
AUTOSENSING ISDN MATRIX SWITCH
Appendix. Troubleshooting
A.1 Calling Black Box
If you determine that your Autosensing ISDN Matrix Switch is malfunctioning, do
not attempt to alter or repair the unit. It contains no user-serviceable parts.
Contact Black Box at 724-746-5500.
Before you do, make a record of the history of the problem. We will be able to
provide more efficient and accurate assistance if you have a complete description,
including:
• the nature and duration of the problem.
• when the problem occurs.
• the components involved in the problem.
• any particular application that, when used, appears to create the problem or
make it worse.
A.2 Shipping and Packaging
If you need to transport or ship your Autosensing ISDN Matrix Switch:
• Package it carefully. We recommend that you use the original container.
• If you are shipping the Autosensing ISDN Matrix Switch for repair, make sure
you include everything that came in the original package. Before you ship,
contact Black Box to get a Return Authorization (RA) number.
1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746
© Copyright 2002. Black Box Corporation. All rights reserved.
Loading...