Economically extend and distribute VGA video,
stereo audio, and serial signals over CATx.
Customer
Support
Information
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S.
call 724-746-5500) • FREE technical support 24 hours a day, 7 days
a week: Call 724-746-5500 or fax 724-746-0746 • Mailing address:
Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Web site: www.blackbox.com • E-mail: info@blackbox.com
Page 2
Trademarks Used in this Manual
Trademarks Used in this Manual
Black Box and the Double Diamond logo are registered trademarks, and
MediaCento is a trademark, of BB Technologies, Inc.
Any other trademarks mentioned in this manual are acknowledged to be
the property of the trademark owners.
Page 2
724-746-5500 | blackbox.com
Page 3
FCC and IC RFI Statements/NOM Statement
FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY
CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS
This equipment generates, uses, and can radiate radio-frequency energy, and if
not installed and used properly, that is, in strict accordance with the manufacturer’s
instructions, may cause inter ference to radio communication. It has been tested
and found to comply with the limits for a Class A computing device in accordance
with the specifications in Subpart B of Part 15 of FCC rules, which are designed
to provide reasonable protection against such interference when the equipment
is operated in a commercial environment. Operation of this equipment in a
residential area is likely to cause interference, in which case the user at his own
expense will be required to take whatever measures may be necessary to correct
the interference.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This digital apparatus does not exceed the Class A limits for radio noise emis sion
from digital apparatus set out in the Radio Interference Regulation of Industry
Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant
les limites applicables aux appareils numériques de classe A prescrites dans le
Règlement sur le brouillage radioélectrique publié par Industrie Canada.
1. Todas las instrucciones de seguridad y operación deberán ser leídas antes
de que el aparato eléctrico sea operado.
2. Las instrucciones de seguridad y operación deberán ser guardadas para
referencia futura.
3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de
operación deben ser respetadas.
724-746-5500 | blackbox.com Page 3
Page 4
NOM Statement
4. Todas las instrucciones de operación y uso deben ser seguidas.
5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo, cerca
de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc.
6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que
sean recomendados por el fabricante.
7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea
recomendado por el fabricante.
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá
a lo descrito en las instrucciones de operación. Todo otro servicio deberá ser
referido a personal de servicio calificado.
9. El aparato eléctrico debe ser situado de tal manera que su posición no
interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá,
alfombra o superficie similar puede bloquea la ventilación, no se debe colocar
en libreros o gabinetes que impidan el flujo de aire por los orificios de
ventilación.
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor
como radiadores, registros de calor, estufas u otros aparatos (incluyendo
amplificadores) que producen calor.
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del
tipo descrito en el instructivo de operación, o como se indique en el aparato.
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización
del equipo no sea eliminada.
13. Los cables de la fuente de poder deben ser guiados de tal manera que no
sean pisados ni pellizcados por objetos colocados sobre o contra ellos,
poniendo particular atención a los contactos y receptáculos donde salen del
aparato.
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las
recomendaciones del fabricante.
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas
de energia.
Page 4
724-746-5500 | blackbox.com
Page 5
NOM Statement
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea
usado por un largo periodo de tiempo.
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean
derramados sobre la cubierta u orificios de ventilación.
18. Servicio por personal calificado deberá ser provisto cuando:
A: El cable de poder o el contacto ha sido dañado; u
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o
C: El aparato ha sido expuesto a la lluvia; o
D: El aparato parece no operar normalmente o muestra un cambio en su
desempeño; o
E: El aparato ha sido tirado o su cubierta ha sido dañada.
4.2.2 Use (Load) Default Setting .....................................................31
4.3 Factory Default Setting on Transmitters and Receivers .....................32
4.3.1 Factory Default Setting on the Transmitter ............................32
4.3.2 Factory Default Setting on the Receiver .................................32
5. LED Indicators ............................................................................................33
Page 6
724-746-5500 | blackbox.com
Page 7
Table of Contents
6. Serial Interface ...........................................................................................36
Appendix A. CAT5 Cables................................................................................37
Appendix B. Control Cable RJ-11/DB9F Pinout ................................................38
Appendix C. Text-Based RS-232 Protocol of MediaCento VX .........................39
724-746-5500 | blackbox.com Page 7
Page 8
Chapter 1: Specifications
1. Specifications
Distance (Maximum) —
AVX-VGA-TP-TX, AVX-VGA-TP-TX-4, AVX-VGA-TP-TX-8:
When used with AVX-VGA-TP-SRX receiver: 492 ft. (150 m);
When used with AVX-VGA-TP-LRX or AVX-VGA-TP-CSRX receiver:
1000 ft. (300 m);
When used with AVX-VGA-TP-LRX and AVX-VGA-TP-CSRX receivers:
1475 ft. (450 m);
AVX-VGA-TP-SRX: 492 ft. (150 m);
AVX-VGA-TP-LRX: 1000 ft. (300 m)
NOTE: 1475 feet has been tested and recommended as the maximum distance,
however, with a good quality cable and environment, distances beyond
2000 feet can be achieved.
MTBF — 90,000 hours
Resolution (Maximum) — 1920 x 1200 at maximum distance
User Controls — AVX-VGA-TP-TX: (1) EDID copy button;
AVX-VGA-TP-TX-4, AVX-VGA-TP-TX-8: (1) EDID copy button; (1) master/slave
switch; (1) cascade on/off switch;
AVX-VGA-TP-SRX, AVX-VGA-TP-LRX, AVX-VGA-TP-CSRX: (3) push buttons:
(1) for entering/exiting video adjustment mode; (1) to increase video
adjustment one level; (1) to decrease video adjustment one level
Approvals — CE, RoHS
Connectors —
AVX-VGA-TP-TX, AVX-VGA-TP-TX-4, AVX-VGA-TP-TX-8:
Video input: (1) HD15 F (VGA);
Audio input: (1) 3.5-mm jack (stereo);
Serial input: (1) DB9 F (RS-232 TX/GND signals);
System configuration: (1) RJ-11 (connects to a host’s serial port via included
control cable and RJ-11/DB9 converter);
Power: (1) 2.1-mm barrel jack;
Ground: (1) ground connector;
AVX-VGA-TP-TX also has: Local video output: (1) HD15 F (VGA);
Interconnect: (1) RJ-45;
Page 8
724-746-5500 | blackbox.com
Page 9
Chapter 1: Specifications
Connectors (Continued)—
AVX-VGA-TP-TX-4 also has:
Cascade output: (1) HD15 F (VGA) for video and RS-232;
Interconnect: (4) RJ-45;
AVX-VGA-TP-TX-8 also has:
Cascade output: (1) HD15 F (VGA) for video and RS-232;
Interconnect: (8) RJ-45;
AVX-VGA-TP-SRX, AVX-VGA-TP-LRX, AVX-VGA-TP-CSRX:
Audio output: (1) 3.5-mm jack (stereo);
Interconnect: (1) RJ-45;
Serial output: (1) DB9 M (RS-232 TX/GND signals);
Power: (1) 2.1-mm barrel jack;
Ground: (1) ground connector;
AVX-VGA-TP-SRX, AVX-VGA-TP-LRX also have:
Video output: (1) HD15 F (VGA);
AVX-VGA-TP-CSRX also has:
Video output/cascade: (1) HD15 F (VGA) for video and RS-232;
Repeater/daisychain: (1) RJ-45 (CATx out)
Indicators — (2) LEDs: (1) Power/Source Input, (1) Link
Size — AVX-VGA-TP-TX: 1.6"H x 5"W x 4"D (4.1 x 12.7 x 10.2 cm);
AVX-VGA-TP-TX-4, AVX-VGA-TP-TX-8: 1.6"H x 6.75"W x 4"D
(4.1 x 17.1 x 10.2 cm);
AVX-VGA-TP-SRX, AVX-VGA-TP-LRX, VX-VGA-TP-CSRX:
The MediaCento VX Extender pair (Tx + Rx) transmits VGA + Audio + Serial signals
via CATx cable(s). With one Cascadable Receiver and one Long-Range Receiver, it
extends up to and over 450 meters away with WUXGA (1920 x 1200)/Full HD (1920
x 1080) resolution. Via cascading, up to 32 threads and more than 1000 display
units broadcast audio/video signals simultaneously to expand system capability.
Each audio or video port can be independently turned on/off. To ensure video
quality, users may manually adjust video signal on Gain (Brightness), Equalizer
(Sharpness), and RGB skew on all receivers (and cascadable receiver).
However, in some cases display problems may occur because of incorrect EDID
communication between the display monitor and the unit or inappropriate EDID
data programmed by display manufacturers. The EDID Copy function enables the
system to either read the necessary EDID information from the unit or copy EDID
from EDID-compliant displays.
The Graphical User Interface (GUI) is easy to use. You can not only enable or disable
audio/video output simply by clicking the icons, but you can also sort the units by
grouping, which makes management easy. Using the GUI does not need complex
commands. You can portray or rename display icons. The system is ideal for public
broadcasting, exhibits, retail stores, courtrooms, stock tickers, bus stations, etc.
2.2 Features
• Transmit VGA + Audio + Serial signals via CATx technology up to and beyond
1440 feet (450 meters) away with repeaters in between.
• Cascade units to broadcast up to 32 threads to more than 1000 display units;
expand system capability.
• Unique Equalizer (sharpness)/Gain (brightness)/RGB Skew adjustment via push
buttons provides optimal video quality.
• Independently turn ON/OFF the audio and video of the remote ports.
• Automatically detects and indicates the source video signal.
• EDID Copy function.
• Supports surge protection.
• Audible confirmation beeps make operation and cross-checking easier.
• LED indicators monitor status.
Page 10
724-746-5500 | blackbox.com
Page 11
Chapter 2: Overview
User-defined icon available: Name and use your own images for every source and
display icon.
• GUI function makes control easier and more effective.
2.3 What’s Included
Your package should include the following items. If anything is missing or damaged,
contact Black Box Technical Support at 724-746-5500 or info@blackbox.com.
AVX-VGA-TP-TX:
• (1) 1-Port Transmitter
• (1) power supply and U.S. power cord
• (1) control cable RJ-11/DB9 F
• (1) ground cable
• (1) set of four rubber feet
• This user manual
AVX-VGA-TP-TX-4:
• (1) 4-Port Transmitter
• (1) power supply and U.S. power cord
• (1) control cable RJ-11/DB9 F
• (1) ground cable
• (1) set of four rubber feet
• This user manual
• Support group monitoring: sort your screens by group and manage them easily.
• Compatible with most popular screen resolutions, including WUXGA
(1920 x 1200)/Full HD (1920 x 1080)/UXGA (1600 X 1200).
• Ideal for public broadcasting, exhibits, retail stores, courtrooms, stock tickers,
bus stations, etc.
Exclusive GUI Features
• Graphically describes connection status.
• Duplicates most commonly used menu items as icons on the top.
•
724-746-5500 | blackbox.com Page 11
Page 12
Chapter 2: Overview
AVX-VGA-TP-TX-8:
• (1) 8-Port Transmitter
• (1) power supply and U.S. power cord
• (1) control cable RJ-11/DB9 F
• (1) ground cable
• (1) set of four rubber feet
• This user manual
AVX-VGA-TP-SRX:
• (1) Standard Receiver, 492 ft. (150 m)
• (1) power supply and U.S. power cord
• (1) ground cable
• (1) set of four rubber feet
• This user manual
AVX-VGA-TP-LRX:
• (1) Long-Range Receiver, 984 ft. (300 m)
• (1) power supply and U.S. power cord
• (1) ground cable
• (1) set of four rubber feet
• This user manual
AVX-VGA-TP-CSRX:
• (1) Long-Range Cascadable Receiver, 984 ft. (300 m)
• (1) power supply and U.S. power cord
• (1) ground cable
• (1) set of four rubber feet
• This user manual
Page 12
724-746-5500 | blackbox.com
Page 13
Chapter 2: Overview
2.4 Hardware Description
Figures 2-1 through 2-5 show the front and back panels of the extenders. Tables 2-1
through 2-5 describe their components.
2.4.1 1-Port Transmitter (AVX-VGA-TP-TX)
11 9 6 3 1 7
12 10 8 4 2 5
Figure 2-1. AVX-VGA-TP-TX front and back panels.
724-746-5500 | blackbox.com Page 13
Page 14
Chapter 2: Overview
Table 2-1. AVX-VGA-TP-TX components.
NumberComponentDescription
1
2
3
4
5
6
7
8
HD15 connectorConnect to a VGA source.
HD15 connectorConnect to a VGA monitor.
Audio jackConnect to an audio source.
Audio jackConnect to a speaker.
RJ-45 jackConnect to a receiver.
Green: Directly connect to an active receiver.
Link LED
Off: No active receiver directly connected.
Green: Power on (without source input).
Status LED
Blue: Source input.
Push buttonEDID setting (see EDID Setting, Section 4.2).
9
10
11
12
Page 14
Serial portConnect to a serial port for serial extension.
R J-11 jack
Barrel connectorLinks to power supply.
Ground terminalConnect to common ground.
Connect to a host’s serial port for system
configuration.
724-746-5500 | blackbox.com
Page 15
Chapter 2: Overview
2.4.2 4-Port Transmitter (AVX-VGA-TP-TX-4)
13 11 8 6 3 1 7
14 12 10 9 4 2 5
Figure 2-2. AVX-VGA-TP-TX-4 front and back panels.
724-746-5500 | blackbox.com Page 15
Page 16
Chapter 2: Overview
Table 2-2. AVX-VGA-TP-TX-4 components.
NumberComponentDescription
1
2
3
4
5
6
7
8
HD15 connectorConnect to a VGA source.
HD15 connectorConnect to a VGA monitor.
Audio jackConnect to an audio source.
Audio jackConnect to a speaker.
(4) RJ-45 jacksConnect to a receiver.
Off: Master mode.
Link LED
Red: Slave mode without source input.
Green: Slave mode with source input.
Status LEDGreen: Power on (without source input).
Blue: Source input.
Master/Slave slide
switch
See Section 2.4.6, Slide Switch.
9
10
11Serial port
12R J-11 jack
13
14
Cascade slide
switch
Push buttonEDID setting (see EDID Setting, Section 4.2).
Barrel connectorConnect power supply.
Ground terminalConnect to common ground.
Page 16
See Section 2.4.6, Slide Switch.
Connect to a serial port for serial extension.
Connect to a host’s serial port for system
configuration.
724-746-5500 | blackbox.com
Page 17
Chapter 2: Overview
2.4.3 8-Port Transmitter (AVX-VGA-TP-TX-8)
13 11 8 6 3 1 5 7
14 12 10 9 4 2 5
Figure 2-3. AVX-VGA-TP-TX-8 front and back panels.
724-746-5500 | blackbox.com Page 17
Page 18
Chapter 2: Overview
Table 2-3. AVX-VGA-TP-TX-8 components.
NumberComponentDescription
1
2
3
4
5
6
7
8
HD15 connectorConnect to a VGA source.
HD15 connectorConnect to a VGA monitor.
Audio jackConnect to an audio source.
Audio jackConnect to a speaker.
(8) RJ-45 jacksConnect to a receiver.
Off: Master mode.
Link LED
Status LED
Master/Slave slide
switch
Red: Slave mode without source input.
Green: Slave mode with source input.
Green: Power on (without source input).
Blue: Source input.
See Section 2.4.6, Slide Switches.
9
10
11DB9 serial port
12R J-11 jack
13
14
Cascade slide
switch
Push buttonEDID setting (see EDID Setting, Section 4.2).
Barrel connectorLinks to power supply.
Ground terminalConnect to common ground.
Page 18
See Section 2.4.6, Slide Switches.
Connect to a serial port for serial extension.
Connect to a host’s serial port for system
configuration.
724-746-5500 | blackbox.com
Page 19
Chapter 2: Overview
2.4.4 Standard Receiver (AVX-VGA-TP-SRX) and Long-Range
Receiver (AVX-VGA-TP-LRX)
1 2 11 13 12
10
8
3 4 5 6 9 7
Figure 2-4. AVX-VGA-TP-SRX or AVX-VGA-TP-LRX front, top, and back panels.
724-746-5500 | blackbox.com Page 19
Page 20
Chapter 2: Overview
Table 2-4. AVX-VGA-TP-SRX or AVX-VGA-TP-LRX components.
NumberComponentDescription
1
2
3
4
5
6
7
HD15 connectorConnect to a VGA monitor.
Audio jackConnect to a speaker.
RJ-45 jackConnect to a transmitter/cascadable receiver.
Push button: - MinusPress once to decrease one level.
Push button: + PlusPress once to increase one level.
Push button: Mode
Status LED
Press the button for two seconds to enter/exit
video adjustment mode.
NOTE: The Master/Slave slide switch is on 4- and 8-port transmitters
(AVX-VGA-TP-TX-4, AVX-VGA-TP-TX-8) only. The Cascade slide switch is on
4- and 8-port transmitters (AVX-VGA-TP-TX-4, AVX-VGA-TP-TX-8) and the
cascadable receiver (AVX-VGA-TP-CRX).
Table 2-6. Slide switches on the 4-/8-Port Transmitter.
SwitchDescription
Master: Unit is set as a source provider.
Master/Slave slide
switch
Cascade slide
switch
Slave: When this unit is a source duplicator, it
accepts an RS-232 signal from an HD15 connector.
Off: The video connector on a transmitter
connects to a VGA monitor.
On: When the video connector on a transmitter
connects to a downstream transmitter, it sends
RS-232 through an HD15 connection.
Table 2-7. Slide switch on the Cascadable Receiver (AVX-VGA-TP-CRX).
SwitchDescription
Off: The video connector on a receiver connects to a
Cascade slide
switch
VGA monitor.
On: When the video connector on a receiver connects
to a downstream transmitter, it sends RS-232 through
an HD15 connection.
Page 24
724-746-5500 | blackbox.com
Page 25
Chapter 3: Installation
3. Installation
WARNING:
• Before installation, power off all devices that will be connected to this system.
• Make sure that all devices you will connect are properly grounded.
• Place cables away from fluorescent lights, air conditioners, and machines that are
likely to generate electrical noise.
Grounding
To prevent any damage to the product or any connecting devices, make sure that
the extender systems are properly grounded.
Connection Pattern
The following figures show typical applications of the MediaCento VX transmitters
and receivers.
3.1 1-Port Transmitter + Receiver
DB9
Transmitter
R J-11
Laptop with
control software
(DTE RS-232)
HD15
CAT5
communication
Receiver
Serial port
2-way
Figure 3-1. Connection pattern for 1-Port Transmitter + Receiver.
4.1 Video Adjustment on Receiver/Cascadable Receiver Unit
To optimize the video signal associated with various cable lengths, users may adjust
the video compensation on the Receiver/Cascadable Receiver Unit. It follows the
order in sequence of: EQ—>Gain—>Skew (Red—>Green—>Blue) —>EQ—>
Gain…
STEP 1: Press and hold the “Mode” button for two seconds. When the “EQ” LED
flashes yellow with one beep, the receiver enters video adjustment mode.
STEP 2: Press the “+” or “-” button once (you will hear a clicking sound) to increase
or decrease one level of video adjustment. You will hear a long buzzer
when the receiver reaches its limit.
STEP 3: Press the “Mode” button to go to the next phase (Gain). The “Gain” LED
flashes yellow with one beep sound. Follow STEP 2 above for adjustment.
STEP 4: Press the “Mode” button to go to the next phase (Skew). The “Skew” LED
flashes red/green/blue with one beep sound. Follow STEP 2 above for
adjustment. The “Skew” LED flashes red, green, or blue to indicate which
color is being adjusted. You will hear a long buzzer sound when the
receiver reaches its limit.
STEP 5: Press and hold the “Mode” button for two seconds. You will hear one beep
when the receiver exits Video Adjustment mode.
NOTE: The timeout is set around 20 seconds.
Table 4-1. LED indicators in Video Adjustment Mode.
LEDStatus
EQFlashing Yellow: Adjust EQ
GainFlashing Yellow: Adjust Gain (brightness)
Flashing Red: Adjust Skew (Red)
Status (Skew)
Flashing Green: Adjust Skew (Green)
Page 30
Flashing Blue: Adjust Skew (Blue)
724-746-5500 | blackbox.com
Page 31
Chapter 4: Operation
4.2 EDID Setting on a Transmitter
In some cases, display problems may occur because of incorrect EDID
communication between the display monitor and the unit or inappropriate EDID
data programmed by display manufacturers. The EDID Copy function enables the
system to either read the necessary EDID information from the unit or copy EDID
from EDID-compliant displays.
NOTE: Before starting EDID Setting, ensure the Cascade Switch is in the “OFF”
position.
4.2.1 EDID Copy
If the transmitter EDID does not match the EDID of the attached displays, copy the
EDID from the displays.
STEP 1: Apply power to the unit.
STEP 2: Connect the display to the Video Out connector on the transmitter and
power on the display.
STEP 3: Press the “EDID Copy” button and release the button RIGHT AFTER the LED
flashes green.
STEP 4: The LED flashes red and green alternately and returns to normal status,
indicating that the copy is successful.
Otherwise, if the LED flashes RED:
a. The monitor is not properly connected.
b. The monitor is not powered on.
c. EDID data of the monitor is not applicable.
Repeat STEPS 2 and 3.
4.2.2 Use (Load) Default Setting
When using a monitor that is NOT EDID compliant, the transmitter will automatically
select viable EDID data from the transmitter’s EDID profile to set up the EDID
information.
STEP 1: Apply power to the transmitter.
STEP 2: Press the “EDID Copy” button and release the button RIGHT AFTER the LED
flashes red.
STEP 3: The LED flashes red and green alternately and returns to normal status
when the copy is successful.
724-746-5500 | blackbox.com Page 31
Page 32
Chapter 4: Operation
4.3 Factory Default Settings on Transmitters and Receivers
To restore the transmitters and receivers to the default settings, follow these steps.
4.3.1 Factory Default Setting on the Transmitter
STEP 1: Press and hold the “EDID Copy” button.
STEP 2: Apply power to the transmitter.
STEP 3: Release the button RIGHT AFTER two LEDs flash.
NOTE: A two-beep sound is used to confirm power supply.
STEP 4: Power cycle the unit.
4.3.2 Factory Default Setting on the Receiver
STEP 1: Press and hold the “+” button.
STEP 2: Apply power to the receiver.
STEP 3: Release the button RIGHT AFTER two LEDs flash.
NOTE: A two-beep sound is used to confirm power supply.
STEP 4: Power cycle the unit.
Page 32
724-746-5500 | blackbox.com
Page 33
5. LED Indicators
Table 5-1. 1-Port Transmitter LEDs.
LEDStatusDescription
Chapter 5: LED Indicators
Link
Status
LEDStatusDescription
Link
Green
Green
Blue
OffSwitch: Master
RedSwitch: Slave (no source input)
Lights when the transmitter is connected to an
active receiver
Power on (no video source input)
Power on and video source detected (source input
detected); LED turns green six seconds after
unplugging the source
Power on and video source detected
(source input detected); LED turns
green six seconds after unplugging
the source
Source detected (local audio output
is off)
Source detected (local video output
is off)
Source detected (local audio and
video output are off)
No source input (local audio output
is off)
Emits green with blue
flashing twice
Emits green with blue
flashing three times
Page 34
No source input (local video output
is off)
No source input (local audio and
video outputs are off)
724-746-5500 | blackbox.com
Page 35
Chapter 5: LED Indicators
Table 5-3. Receiver LEDs.
LEDStatusStatus
RedPower on
Link
GreenCAT5 connection detected
Status
Green
Blue
Emits blue with green
flashing once
Emits blue with green
flashing twice
Emits blue with green
flashing three times
Emits green with blue
flashing once
Power on (no video source input)
Power on and video source detected
(source input detected); LED turns
green six seconds after unplugging
the source
Source detected (local audio output
is off)
Source detected (local video output
is off)
Source detected (local audio and
video output are off)
No source input (local audio output
is off)
Emits green with blue
flashing twice
Emits green with blue
flashing three times
Flashing yellowRS-232 off
EQ
OffRS-232 on
724-746-5500 | blackbox.com Page 35
No source input (local video output
is off)
No source input (local audio and
video outputs are off)
Page 36
Chapter 6: Serial Interface
6. Serial Interface
NOTE: The MediaCento VX management software can be found on the Black Box
Web site (www.blackbox.com). Navigate to one of the product pages by
entering “MediaCento VX” into the search text box. You will find the
software user manual and software download link under “Resources” in each
product of the family. For further questions, contact Black Box Technical
Support at 724-746-5500 or info@blackbox.com
Page 36
724-746-5500 | blackbox.com
Page 37
Appendix A: CAT5 Cables
Appendix A. CAT5 Cables
The extender pair requires a piece of unshielded twisted-pair (UTP) CAT5 cable.
The cable should be wired according to the TIA/EIA 568B standard shown below.
Table A-1. RJ-45 pinout.
PinWire ColorPair
1
2
3
4
5
6
7
8
White/Orange2
Orange2
White/Green3
Blue1
White/Blue1
Green3
White/Brown4
Brown4
NOTE: Use CAT5, CAT5e, or CAT6 cables to connect the extender pair.
The diagram above shows the RJ-45 connector of a CAT5 cable with its metal
contacts facing up.
724-746-5500 | blackbox.com Page 37
Page 38
Appendix B: Control Cable RJ-11/DB9F Pinout
Appendix B. Control Cable RJ-11/DB9F Pinout
Table B-1. RJ-11/DB9F control cable pinout.
RJ-11MDB9F
1
2
3
4
5
6
4
3
5
1
2
6
Page 38
724-746-5500 | blackbox.com
Page 39
Appendix C: Text-Based RS-232 Protocol
Appendix C: Text-based RS-232 Protocol of MediaCento™ VX
RS-232 Communication setting:
Baud rate: 38400
Data bit: 8
Parity bit: 0
Stop bit: 1
Flow control: none
Letter case: none
The command set has the following format (Command is ASCII format).
(a1.a2.a3.a4.a5.a6)XXX=n,m[CR]
a1.a2.a3.a4.a5.a6
(Optional) The Address packet of the destination device node, variable length, with
a maximum length of 6. This is required when sending a command to destination
node.
When command line doesn’t include an Address packet that indicates this, the
command will be broadcasted to all nodes.
Each byte of an address packet is hexadecimal-text, low nibble is the TX port index
(zero-based), high nibble is Expanded port index (1-based).
The device tree has to follow the rules listed below:
• The first layer only can expand to four splitters.
• You can only can extend to four layers of Repeaters in the device tree.
• You can only can expand one Splitter on a Repeater’s expanded port.
For example, (see the device tree listed below):
(00) – root node, a Splitter
(10) – the node on the expanded port of node (00), a Splitter
(20) – the node on the expanded port of node (10), a Splitter
(30) – the node on the expanded port of node (20), a Splitter
(30.00), a Repeater — The node on the TX port 1 of node (30)
(30.10), a Splitter — The node on the expanded port of node (30.00)
724-746-5500 | blackbox.com Page 39
Page 40
Appendix C: Text-Based RS-232 Protocol
(30.10.00), a Repeater — The node on the TX port 1 of node (30.10)
(30.10.00.00), a Receiver — The node on the TX port 1 of node (30.10.00)
[CR] carriage return ASCII code (hex value = 0x0D), the end of command packet
[LF] line feed ASCII code ( hex = 0x0A )
[ESC] Escape ASCII code
For example,
If you want to set all video on, you can send a command like this:
VEN[CR]
If you want to set the video on node (30.10.00.00), you can send a command like
this:
(30.10.00.00)VEN[CR]
If you want to set the audio on node (30.10.00.00) and all branches, you can send a
command like this:
(30.10.00.00)BS_AEN[CR]
If you want to enable the public audio on node (30.10.00.00) and all branches, you
can send a command like this,
(30.10.00.00)TEMP_AEN[CR]
When the “first” transmitter, which is directly connected to a PC, receives the
command, it will reply with a code:
Correct [CR][LF] (this means the command is correct) or
Incorrect [CR][LF] (this means the command is incorrect)
Set EQ, Gain, Red de-skew,
Green de-skew, Blue de-skew
Set EQ, Gain, Red de-skew,
Green de-skew, Blue de-skew,
Video, Audio, RS-232, Buzzer
Reset EQ, Gain, Red de-skew,
Green de-skew, Blue de-skew, Video,
Audio, RS-232, Buzzer
Reset local with branch EQ, Gain,
Red de-skew, Green de-skew, Blue
de-skew, Video, Audio, RS-232,
Buzzer
(refer to Error
Code List in
Table C-4)
Page 42
724-746-5500 | blackbox.com
Page 43
Appendix C: Text-Based RS-232 Protocol
Table C-2. Node with Branch Broadcast Set Command List.
Command SetDescriptionStatus Returned
BS_VEN [CR] Branch control video on
BS_VDIS[CR] Disable video
BS_AEN[CR] Enable audio
BS_ADIS[CR] Disable audio
BS_REN[CR] Enable RS-232
BS_RDIS[CR] Disable RS-232
BS_BEN[CR] Enable Buzzer output
BS_BDIS[CR] Disable Buzzer output
BS_ AVEN [CR] Enable audio & video
BS_ AVDIS[CR] Disable audio & video
BS_XEN [CR]
BS_XDIS[CR]
BS_X=0000[CR]
Enable audio, video, RS-232,
Buzzer
Disable audio, video, RS-232,
Buzzer
Set Video, Audio, RS-232,
Buzzer
(refer to Error Code List
in Table C-4)
724-746-5500 | blackbox.com Page 43
Page 44
Appendix C: Text-Based RS-232 Protocol
Table C-3. Node with Branch Temporarily Control Command List.
Command SetDescription
TEMP_VEN [CR] Temporarily control video on
TEMP_VDIS[CR] Temporarily control video off
TEMP_V_OFF[CR] Temporarily control video cancel
TEMP_AEN[CR] Temporarily control audio on
TEMP_ ADIS [CR] Temporarily control audio off
Status
Returned
TEMP_A_OFF[CR] Temporarily control audio cancel
TEMP_ REN [CR] Temporarily control RS-232 enable
TEMP_RDIS[CR] Temporarily control RS-232 disable
TEMP_R_OFF[CR] Temporarily control RS-232 cancel
TEMP_ BEN [CR] Temporarily control Buzzer enable
TEMP_ BDIS [CR]Temporarily control Buzzer disable
TEMP_B_OFF[CR] Temporarily control Buzzer cancel
TEMP_ AV EN [CR] Temporarily control audio & video on
TEMP_ AV DIS [CR] Temporarily control audio & video off
TEMP_AV_OFF[CR] Temporarily control audio & video cancel
(refer to Error
Code List in
Table C-4)
TEMP_ XEN [CR]
Page 44
Temporarily control audio, video, RS-232,
Buzzer on
724-746-5500 | blackbox.com
Page 45
Appendix C: Text-Based RS-232 Protocol
Table C-3 (Continued). Node with Branch Temporarily Controlling Command List.
Command SetDescriptionStatus Returned
TEMP_ XDIS [CR]
TEMP_X_OFF[CR]
TEMP_X=0000[CR]
Error Code (ASCII)Description
Correct [CR][LF] Command correct
Incorrect command [CR][LF] Command fail
Temporarily control audio, video,
RS-232, Buzzer off
Temporarily control audio, video,
RS-232, Buzzer cancel
Temporarily control Video, Audio,
RS-232, Buzzer
Table C-4. Error Code List.
Refer to error list
in Table C-4.
Refer to error list
in Table C-4.
Refer to error list
in Table C-4.
Incorrect parameter [CR][LF] Parameter fail
Control Logic = ((Temporarily set) || ( Branch set && Local set ))
724-746-5500 | blackbox.com Page 45
Page 46
NOTES
Page 46
724-746-5500 | blackbox.com
Page 47
NOTES
724-746-5500 | blackbox.com Page 47
Page 48
Chapter
Black Box Tech Support: FREE! Live. 24/7.
Tech support the
way it should be.
Great tech support is just 30 seconds away
at 724-746-5500 or blackbox.com.
About Black Box
Black Box provides an extensive range of networking and infrastructure products.
You’ll find everything from cabinets and racks and power and surge protection
products to media converters and Ethernet switches all supported by free, live 24/7
Tech support available in 30 seconds or less.