Blackbox ACU5000A, ACU5003, ACU5004 User Manual

1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax [phone]

© Copyright 2002. Black Box Corporation. All rights reserved.

SERVSWITCH™ WIZARD EXTENDER CHASSIS AND BLANK CHASSIS PANELS

To mount a module in an Extender Chassis, take these steps, referring to the

figure below:

1. Slide the module into the chassis with the protruding tip of its endplate
pointing upwards.

2. Screw the M3 pan-head screw included with the module through the hole at
the top of the module’s endplate and the matching hole in the front flange of
the chassis in order to secure the module to the chassis.

Attach a Single Blank Panel to the vhassis with the panel’s included screw in the
same way you’d mount a module. Attach a Quad Blank Panel to the chassis with
one of the panel’s included screws in the panel’s upper left corner and the other
in the upper right corner.

To mount the chassis in your rack, hold its side flanges against the vertical rails
of your rack, then use four of your own screws, bolts, cage nuts, etc., to secure the
flanges to the rails.

Mounting a module and panels in an Extender Chassis.

ServSwitch Wizard

Extender Chassis

(ACU5000A)

Extender

module

Single Panel

(ACU5003)

Quad Panel

(ACU5004)

Modules and Single Panels come with one

M3 pan-head screw for chassis attachment;

Quad Panels come with two such screws

CUSTOMER

SUPPORT

INFORMATION

Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax [phone]
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Web site: www.blackbox.com • E-mail: [e-mail]

SEPTEMBER 2002

ACU5000A

ACU5003
ACU5004

ServSwitch™ Wizard Extender Chassis

and Blank Chassis Panels

The ServSwitch™ Wizard Extender Chassis (ACU5000A) is designed to hold
modules for the ServSwitch Wizard Extender system and be mounted in 2U of
vertical space in a standard 19" equipment rack. If you don’t completely fill the
chassis with modules, the ServSwitch Wizard Extender Single (ACU5003) and
Quad (ACU5004) Blank Chassis Panels can be installed over any empty slots.

The chassis is steel, measures

3.4"H x 19"W x 9"D (8.7 x 48.3 x 22.8 cm), and
weighs 4.4 lb. (2 kg). It comes with this installation sheet. At the time of this
writing, it can hold these modules: ServSwitch Wizard Extender transmitters
and receivers (ACU5010A and ACU5011A), ServSwitch Wizard Skew
Compensators (ACU5100A), and ServSwitch™ Wizard Extender Chassis Power

Supplies (PS5000).

The Blank Chassis Panels are also steel. The Single Panel covers one empty

chassis slot; it measures

3.3"H x 1"W x 1.5"D (8.3 x 2.6 x 3.9 cm), weighs 1.3 oz.
(37 g), and comes with this installation sheet and a single M3 pan-head screw
for mounting it in the chassis. The Quad Panel covers four empty slots; it
measures 3.3"H x 4.6"W x 1.5"D (8.3 x 11.6 x 3.9 cm), weighs 5.2 oz. (147 g),
and comes with this sheet and two M3 pan-head screws.