B-K lighting PS, PSL Installation Instructions Manual

PS™ / PSL™

TECHNOLOGY

with

TECHNOLOGY

& Low Voltage

Installation Instructions

Warning Flammable Hot Surface

High Voltage

TOOLS

NEEDED:

By Others

1/8” Allen Wrench

Waterproof Wire Connectors

Mounting Hardware

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY

INSTRUCTIONS

WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before replacing lamp.

Lamp gets HOT quickly! Contact only switch/plug when

Do not touch hot lens, guard, or enclosure (see diagram/

Do no touch the lamp at any time. Use a soft cloth. Oil

Do not operate the luminaire fitting with a missing or

Lighted lamp is HOT!

turning on.

Keep lamp away from materials that may burn.

picture).

from skin may damage lamp.

damaged shield.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY

AND INSTALLATION INSTRUCTIONS

• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel must perform all servicing or relamping of
this product.

• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.

• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.

• Replace lamp only with correct wattage and type of lamp
marked on fixture label.

• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.

IMPORTANT LISTINGS AND CERTIFICATIONS

· Suitable for wet locations • Suitable for mounting within 4 ft. of the ground.

Proper soil preparation is recommended before installation. See the DIG-IT guide at www.bklighting.com/dig-it for more information.

This set of instructions works for:

PS - Path Star™

PSL - Louvered Path Star™

PSL

Anchor Base

on Power Pipe

TM

Stability Flange

18 Gauge Wire

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX [phone]

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

www.bklighting.com • [e-mail]

RELEASE DATE

11-30-16

REFERENCE NUMBER

INS000733.1

PS

Finished grade

Concrete

Finished grade

Finished grade

Optional

Stability Flange

Pea gravel
or sand

Finished grade

Pea gravel
or sand

Concrete

Finished grade

Finished grade

Optional

Stability Flange

Pea gravel
or sand

Finished grade

Pea gravel
or sand

Concrete

Finished grade

Pea gravel
or sand

Finished grade

Pea gravel
or sand

Concrete

Finished grade

Pea gravel
or sand

TECHNOLOGY

with

TECHNOLOGY

& Low Voltage

PS™ / PSL™

Installation Instructions

TRANSFORMER HOUSING MUST BE INSTALLED ABOVE GRADE. POWER PIPE™ IS LABELED AT GRADE LEVEL.

TRANSFORMER HOUSING INSTALLED BELOW GRADE WILL VOID WARRANTY

Soil Prep

Excavated

Conduit
trench

for Housing

Conduit
Trench

A. Determine Soil Type by referencing DIG-IT Guide.

Prep soil according to DIG-IT Guide.

B. Dig hole 10” wide and 24” deep.

Power Pipe with Anchor Base Mounting Option

1. Excavate trench according to designed lighting
plan. Dig hole a minimum of 18” deep and 10”
wide to accommodate Power Pipe™ at desired
fixture locations.

2. Slide optional Stability Flange onto Power
Pipe™. Use optional Stability Flange to aid in
installation of Power Pipe™.

C. Prep soil according to DIG-IT Guide.

3. Pull branch circuit wiring necessary for
installation (By Others) to Power Pipe™. Place
Power Pipe™ in hole.

Allow for additional cable to make connections

to fixture leads and future service. Do not cut
PVC.

Remote
Transformer

4. Back fill with pea gravel or sand prior to pour.

5. Pour concrete (By Others).

Label on Power Pipe™ indicates installation

depth with finished grade.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

40429 Brickyard Drive • Madera, CA 93636 • USA

B-K LIGHTING

559.438.5800 • FAX [phone]

www.bklighting.com • [e-mail]

Remote Transformer

6. Make watertight connections from remote 12V
transformer to LED source leads (18 gauge wire)
using waterproof wire connectors (By Others).

See wiring diagram.

RELEASE DATE

11-30-16

REFERENCE NUMBER

INS000733.1

TECHNOLOGY

with

TECHNOLOGY

120V 12V

Fixture

COM

Remote

Transformer

COM

120V 12V

Fixture

COM

GROUND

Integral

Transformer

COM

GROUND IN HOUSING

Integral
Transformer

& Low Voltage

Installation Instructions

PS™ / PSL™

Integral Transformer

7. Pull branch circuit wires necessary for
installation (By Others) through Power Pipe™.
Use waterproof wire connectors (By Others) to
connect transformer primary leads to branch
circuit wires. Connect incoming ground to
ground wire provided in fixture body. See

wiring diagram.

WIRING DIAGRAM

8. Place fixture on anchor base and tighten four (4)
#10-32 stainless steel button head cap screws
using a 1/8” Allen wrench.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

B-K LIGHTING

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX [phone]

www.bklighting.com • [e-mail]

RELEASE DATE

11-30-16

REFERENCE NUMBER

INS000733.1