B-K lighting NITE STAR Installation Instruction

NITE STAR SERIES™

Bluetooth® Wireless Technology

TOOLS

NEEDED:

3/16” & 5/32” Allen Wrench

Waterproof Wire Connectors

Inspiration Control System on iOS Device

Warning Low Voltage Hot Surface

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY TO

PERSONS IMPORTANT SAFETY

INSTRUCTIONS

Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before replacing LED.
Fixture gets HOT quickly! Contact only switch/plug when
turning on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield

a soft cloth or gloves. Oil from skin may cause damage.

. Do not touch the source at any time. Use

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY

• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.

• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.

By Others

AND INSTALLATION INSTRUCTIONS

• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.

• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.

• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.

IMPORTANT LISTINGS AND CERTIFICATIONS

· Suitable for wet locations

Please refer to the low voltage design guide at www.bklighting.com/lvguide before installation for proper wire selection.

Device Requirements

iOS device with installed Inspiration Control System
App is required for Bluetooth® Wireless Control.

Bluetooth® version 4.0 or higher required.

iOS Devices:

iPhone - iPhone 4s or newer

iPad - 3rd Gen iPad or newer
iPad Mini
iPad Air

iPod Touch 5th Gen or newer

iPod -

Optional 360SL™

Knuckle Mounting
System

1/2” NPS Threaded Hub

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

Locknut

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX [phone]

www.bklighting.com • [e-mail]

RELEASED

4-8-16

REFERENCE NUMBER

INS-2407-00

LINE

MODULE

COM

Remote

Transformer

Red

Black

LCT

wireless (0-10v dimming, continuous cct, sat. and hue by LCT)

LINE

MODULE

COM

GROUND

Remote

Transformer

10V

0V

Gray (Common)

Violet (0-10V)

Red

Black

Dimming

hybrid (0-10v dimming wired, /continuous cct, sat. and hue by iOS)

LCT

iOS

Bluetooth®

GROUND

LINE

MODULE

COM

GROUND

Remote

Driver

10V

0V

Gray (Common)

Violet (0-10V)

Red

Black

LCT

Dimming

hybrid (0-10v dimming wired, /continuous cct, sat. and hue by LCT)

iOS

Bluetooth®

DE WIRING CHECK

iOS device (Not Included) with installed B-K Lighting Inspiration Application required for use.

Wireless Bluetooth® Controls with Inspiration Application

NITE STAR SERIES™

Bluetooth® Wireless Technology

1. Mount fixture onto suitable enclosure according
to designed lighting plan.

2. Secure ½” NPS stem to mounting option. Secure
with provided locknut if applicable.

3. Pull remote wiring through mounting plate.
Make connections from remote transformer to
fixture leads using waterproof wire connectors
(By Others). See wiring diagram.

LED - For use with 12VAC
transformer or magnetic transformers only.
B-K Lighting cannot guarantee performance
with third party manufacturers’ transformers.

remote

LINE

Remote

Transformer

COM

GROUND

WIRING DIAGRAM - Wireless Bluetooth® Controls

with Inspiration Application on iOS device

iOS device controls dynamic lumen output using

Bluetooth® wireless controls and the application.

iOS device (iPad, iPod, iPhone) with installed

B-K Lighting Inspiration application is
required.

iOS device must be within signal range of

fixture for wireless operation.

12V

COM

MODULE

iOS

Bluetooth®

4. Use 5/32” Allen wrench to slightly loosen #10-32
stainless steel black oxide socket head cap screw
at the knuckle for aiming purposes. Tighten to
secure desired location.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

B-K LIGHTING

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX [phone]

www.bklighting.com • [e-mail]

RELEASED

4-8-16

REFERENCE NUMBER

INS-2407-00

Standard Adjustment

Warning Hot Surface

360SL™ Mounting System

TOOLS

NEEDED:

By Others

5/32” & 5/64” Allen wrench

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY TO

PERSONS IMPORTANT SAFETY

INSTRUCTIONS

WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before replacing lamp.

Lamp gets HOT quickly! Contact only switch/plug when

Do not touch hot lens, guard, or enclosure (see diagram/

Do no touch the lamp at any time. Use a soft cloth. Oil

Do not operate the luminaire fitting with a missing or

Lighted lamp is HOT!

turning on.

Keep lamp away from materials that may burn.

picture).

from skin may damage lamp.

damaged shield.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY

AND INSTALLATION INSTRUCTIONS

• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel must perform all servicing or relamping of
this product.

• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.

• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.

• Replace lamp only with correct wattage and type of lamp
marked on fixture label.

• All gaskets, O-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.

IMPORTANT LISTINGS AND CERTIFICATIONS

· Suitable for wet locations · Additionally suitable for mounting within 4 ft. of the ground

360SL™ Knuckle

1. Use 5/64” Allen wrench to slightly loosen two (2)
#8-32 stainless steel set screws on the stem for 360°
aiming purpose.

2. Rotate fixture at base and aim fixture to desired
horizontal location.

3. Use 5/32” Allen wrench to loosen #10-32 stainless
steel black oxide socket head cap screw at the
knuckle for vertical aiming purpose.

4. Tighten two (2) #8-32 stainless steel set screws on
stem to secure horizontal aiming position.

Tighten #10-32 stainless steel black oxide socket

head cap screw to 15” minimum to 30” maximum
pounds to secure vertical aiming position.

Warning: Do not over tighten set screw. Doing
so will compromise O-ring seal and will void
warranty.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX [phone]

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

www.bklighting.com • [e-mail]

RELEASED

1-31-14

REFERENCE NUMBER

INS-2097-00

with

TECHNOLOGY

TECHNOLOGY

Standard Installation/Replacement

LED BOARD/DRIVER/OPTICS

2 1/4” Body Size

TOOLS

NEEDED:

5/64” & 9/64” Allen Wrench

Small Flat Head Screw Driver

Warning Low Voltage Hot Surface

INSTRUCTIONS PERTAINING TO

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY

A RISK OF FIRE, OR INJURY TO

PERSONS IMPORTANT SAFETY

INSTRUCTIONS

WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before replacing lamp.

Lamp gets HOT quickly! Contact only switch/plug when

Do not touch hot lens, guard, or enclosure (see diagram/

Do no touch the lamp at any time. Use a soft cloth. Oil

Do not operate the luminaire fitting with a missing or

Lighted lamp is HOT!

turning on.

Keep lamp away from materials that may burn.

picture).

from skin may damage lamp.

damaged shield.

SAVE THESE INSTRUCTIONS

• Product must be installed by a qualified person in a manner

consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.

• Followproductlabelinformationandinstructions.

• Qualified Personnel mustperform all servicing orrelamping of

this product.

• Beforewiringtopowersupplyandduringservicingorrelamping,

turn off power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the

manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.

IMPORTANT LISTINGS AND CERTIFICATIONS

This product is available with Adjust-e-Lume® (Patent Pend.) for DynamicLLumen Output Control

Warning! The light output of this product may be dynamically adjusted as desired to raise and lower light levels. Please ensure the xture is set to the
appropriate light level desired during installation.

Re-placing LED Board/Driver and Optics

By Others

AND INSTALLATION INSTRUCTIONS

• Do notblock light emanatingfrom productin wholeor part,

as this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot

lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.

• Replace lamp only with correct wattage and type of lamp

marked on fixture label.

• All gaskets, o-rings and sealing surfacesmust be keptclean

during installation and service; failure to do this may cause an
unsafe condition and void product warranty.

1. Use 5/64” Allen wrench to loosen #8-32 stainless
set screw and remove cap.

4. Disengage LED board and driver assembly. Replace
with new board and driver assembly.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

2. Space three fingers evenly around the optic and
gently rock optic to remove.

5. Reverse install LED board and driver by carefully
engaging quick disconnects and inserting into
fixture body. Secure LED board in place with
stainless steel screws. Snap optics in place.

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX [phone]

www.bklighting.com • [e-mail]

3. Use 5/64” Allen wrench to remove two (2) #2-56
socket head cap screws on LED board, grasp
LED board and gently pull up to expose quick
disconnect.

6. With flat head screw driver rotate dial to desired
lumen output. Replace cap by securing #8-32
set screw with 5/64” Allen wrench. Do not over

tighten set screw.

RELEASED

2-24-16

REFERENCE NUMBER

INS000001

with

TECHNOLOGY

TECHNOLOGY

Standard Installation/Replacement

7. Place cap on fixture and tighten set screw. Tighten
screw to 1/2 inch pounds. Top of screw should sit
flush with fixture cap.

Warning: Do not over tighten set screw.
Doing so will compromise O-Ring seal and
will void warranty.

This product is available with Adjust-e-Lume® (Patent Pend.) for DynamicLLumen Output Control

Warning! The light output of this product may be dynamically adjusted as desired to raise and lower light levels. Please ensure the xture is set
to the appropriate light level desired during installation.

To Change Lumen Output (when required).

LED BOARD/DRIVER/OPTICS

2 1/4” Body Size

1. Use 5/64” Allen wrench to loosen #8-32
stainless set screw and remove cap.

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING
IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

2. With flat head screw driver rotate dial to
desired lumen output.

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX [phone]

www.bklighting.com • [e-mail]

3. Place cap on fixture and tighten set screw.
Tighten screw to 1/2 inch pounds. Top of
screw should sit flush with fixture cap.

Warning: Do not over tighten set screw.

Doing so will compromise O Ring seal and
will void warranty.

RELEASED

2-24-16

REFERENCE NUMBER

INS000001