B-K lighting HP2 Installation Instructions Manual

HP2 SERIES™

12W-24W Integral Driver - Solid State LED

Installation Instructions

NEEDED

FOR

INSTALLATION:

1/8” Allen Wrench

Waterproof Wire Connectors

Level

Phillips Screwdriver

Warning High Voltage Hot Surface

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY TO

PERSONS IMPORTANT SAFETY

INSTRUCTIONS

WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before replacing lamp.

Lamp gets HOT quickly! Contact only switch/plug when

Do not touch hot lens, guard, or enclosure (see diagram/

Do no touch the lamp at any time. Use a soft cloth. Oil

Do not operate the luminaire fitting with a missing or

Lighted lamp is HOT!

turning on.

Keep lamp away from materials that may burn.

picture).

from skin may damage lamp.

damaged shield.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY

• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel must perform all servicing or relamping of
this product.

• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.

By Others

AND INSTALLATION INSTRUCTIONS

• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.

• Replace lamp only with correct wattage and type of lamp
marked on fixture label.

• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.

IMPORTANT LISTINGS AND CERTIFICATIONS

· Suitable for wet locations · Suitable for recessed in ground locations

Proper soil preparation is recommended before installation. See the DIG-IT guide at www.bklighting.com/dig-it for more information.

Faceplate

Quick
Disconnect

Patented

Hydro-

Lock™ Plate

Specify

Fixture
Separately

Driver Tray

Concrete Pour

Waterproof Wire

Connectors

Collar

Patented

Stability

Flange™

Silicone ‘O’ Ring

HP2 Housing

Soil Prep

Conduit
trench

A. Determine Soil Type by referencing

DIG-IT Guide.

B. Dig hole 18” wide and 20” deep.

Excavated
for Housing

C. Prep soil according to DIG-IT Guide.

Conduit
Trench

18”

Dia.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX [phone]

www.bklighting.com • [e-mail]

RELEASE DATE

12-19-16

REFERENCE NUMBER

INS-2388-00

HP2 SERIES™

12W-24W Integral Driver - Solid State LED

Installation Instructions

Housing Installation

Side Flats

Threaded Entry

1. Connect branch conduit connectors (By Others)
to the junction box using either the threaded
conduit entries on the bottom of the junction
box or through holes drilled into the sides of the
junction box.

Flush with finished grade

PROJECT:

TYPE:

2. Place housing in hole. Align junction box in the
path of the conduit trench.

3. Insert (4) pieces of ½” EMT conduit through the
Stability Flange™. Hammer into substrate until
secure.

Leave sufficient clearance to elevate housing

to finished grade.

4. Raise housing on EMT so concrete pour collar is
flush with finished grade. Use a level to aid in
housing installation.

7. Per DIG-IT Guide, backfill the gap between the
bottom of housing and bottom of hole with
sand for drainage.

5. When housing is level, tighten screws on
Stability Flange™ to secure housing to EMT.
Remove excess EMT as needed.

8. For soil installation: Fill and tamp soil to
the appropriate height leaving room for sod,
pavers, etc. to be level with the top of the
temporary cover.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

6. Connect the conduit to the conduit connectors.

9. For concrete installation: Fill the hole around
the fixture housing to 12” below the finished
grade with clean fill dirt and tamp carefully to
prevent settling of fixture. Pour concrete and
finish as required flush with the top surface of
the temporary cover.

B-K LIGHTING

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX [phone]

www.bklighting.com • [e-mail]

RELEASE DATE

12-19-16

REFERENCE NUMBER

INS-2388-00

HP2 SERIES™

12W-24W Integral Driver - Solid State LED

Installation Instructions

Installation

1. Remove temporary cover.

2. Pull primary branch circuit wiring and dimmer
wiring into junction box.

PROJECT:

TYPE:

3. Make connections using silicone filled wire nuts
(provided) to leads on the bottom of Patented
HydroLock® Barrier Plate Assembly. See wiring

diagram.

LINE

GROUND

COM

WIRING DIAGRAM

For use with 12-24 watt dimming driver.

LINE

GROUND

COM

HYDRO-LOCK®

PLATE

4. Wipe inside of housing where HydroLock® plate
will sit clean of debris before inserting patented
HydroLock® plate on to junction box. Align
HydroLock® plate with pins in housing and seat
it firmly in place.

7. Lower driver assembly into HP2 housing.

5. Turn HydroLock® Barrier Plate clockwise ¼” to
lock.

Patented HydroLock® Barrier Plate must be

completely seated to ensure proper seal or
water may intrude. This step must be done
as stated or you will void your warranty.

8. Attach driver assembly to housing by aligning
keyhole notch under one (1) of three (3) #8
screw heads.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

6. Connect driver assembly to Patented
HydroLock® Barrier plate with quick disconnect.

9. Tighten the Phillips screws to secure driver
plate to housing.

B-K LIGHTING

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX [phone]

www.bklighting.com • [e-mail]

RELEASE DATE

12-19-16

REFERENCE NUMBER

INS-2388-00

HP2 SERIES™

12W-24W Integral Driver - Solid State LED

Installation Instructions

10. Remove any dirt or debris in O-ring groove near
top of housing. Place O-Ring inside of groove.

Failure to clean groove of debris will cause
fixture to fail and void product warranty.

PROJECT:

TYPE:

11. Attach fixture to installed driver assembly with
quick disconnect.

12. Install faceplate using 1/8” Allen wrench and
hand-tighten the faceplate screws in a star
pattern to 30 in-lbs. min.

Do not use a power tool to install screws. Do

not exceed 40 in-lbs.

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

B-K LIGHTING

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX [phone]

www.bklighting.com • [e-mail]

RELEASE DATE

12-19-16

REFERENCE NUMBER

INS-2388-00

Standard Adjustment

Warning Hot Surface

360HD™ Knuckle Mounting System

TOOLS

NEEDED:

By Others

3/16” Allen wrench

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY TO

PERSONS IMPORTANT SAFETY

INSTRUCTIONS

WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before replacing lamp.

Lamp gets HOT quickly! Contact only switch/plug when

Do not touch hot lens, guard, or enclosure (see diagram/

Do no touch the lamp at any time. Use a soft cloth. Oil

Do not operate the luminaire fitting with a missing or

Lighted lamp is HOT!

turning on.

Keep lamp away from materials that may burn.

picture).

from skin may damage lamp.

damaged shield.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY

AND INSTALLATION INSTRUCTIONS

• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel must perform all servicing or relamping of
this product.

• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.

• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.

• Replace lamp only with correct wattage and type of lamp
marked on fixture label.

• All gaskets, O-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.

IMPORTANT LISTINGS AND CERTIFICATIONS

· Suitable for wet locations · Additionally suitable for mounting within 4 ft. of the ground

360HD™ Knuckle Mounting System

1. Use 3/16” Allen wrench to slightly loosen
(1) 3/8”-16 x 3/8” stainless steel black oxide set screw
on the stem for 360° aiming purpose.

2. Rotate fixture at base and aim fixture to desired
horizontal location.

3. Use 3/16” Allen wrench to loosen (1) 1/4”-28 x 1-1/4”
stainless steel black oxide socket head cap screw at
the knuckle for vertical aiming purpose.

4. Tighten (1) 3/8”-16 x 3/8” stainless steel black oxide
set screw on the stem to secure horizontal aiming
position.

Tighten (1) 1/4”-28 x 1-1/4” stainless steel black

oxide socket head cap screw to 24” minimum to 48”
maximum pounds to secure vertical aiming position

Warning: Do not over tighten set screw. Doing
so will compromise O-ring seal and will void
warranty.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX [phone]

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

www.bklighting.com • [e-mail]

RELEASED

1-31-14

REFERENCE NUMBER

INS-2096-00

Standard Installation Replacement

Warning

INSTRUCTIONS PERTAINING TO

A RISK OF FIRE, OR INJURY TO

PERSONS IMPORTANT SAFETY

INSTRUCTIONS

Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before replacing LED.
Fixture gets HOT quickly! Contact only switch/plug when
turning on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time. Use

a soft cloth or gloves. Oil from skin may cause damage.

SAVE THESE INSTRUCTIONS

· Suitable for wet locations

Hot Surface

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY

• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.

• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.

IMPORTANT LISTINGS AND CERTIFICATIONS

LED BOARD / OPTICS

Power of X (x58-x63)

TOOLS

NEEDED:

By Others

AND INSTALLATION INSTRUCTIONS

.050” & 5/64” Allen Wrench

• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.

• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.

• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.

This product is available with field replaceable components. Exclusive interchangeable OPTIKITS and modular
LED components with quick disconnects simplifies upgrades and maintenance when necessary.

1. Use 5/64” Allen wrench to slightly loosen
three (3) #8-32 stainless steel set screws to remove
cap.

2. Remove optic by pulling gently and lift up.

3. Use .050” Allen wrench to loosen three (3) set
screws holding optic holder and LED module.

4. Gently lift LED module and disconnect from fixture.
Install new LED module. Secure set screws through
LED module and optic holder using .050” Allen
wrench.

Do not pull on connector or wiring. Handle with

care.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

5. Replace optic by lining tabs with optic holder, then
pressing down gently until secured into place.

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX [phone]

www.bklighting.com • [e-mail]

6. Place cap on fixture and tighten set
screws. Tighten screw to 1/2 in-lbs. Top
of screws should sit flush with fixture cap.

Warning: Do not over tighten set screws. Doing
so will compromise O-Ring seal and will void
warranty.

RELEASED

8-17-18

REFERENCE NUMBER

INS000010

Standard Installation Replacement

TOOLS

NEEDED:

LED BOARD / OPTICS

Power of X (x64-x66)

.050” & 5/64” Allen Wrench

Warning Hot Surface

INSTRUCTIONS PERTAINING TO

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY

A RISK OF FIRE, OR INJURY TO

PERSONS IMPORTANT SAFETY

INSTRUCTIONS

Lighted fixture is HOT!
WARNING - To reduce the risk of
FIRE OR INJURY TO PERSONS:

Turn off/unplug and allow to cool before replacing LED.
Fixture gets HOT quickly! Contact only switch/plug when
turning on. Do not touch hot lens, guard, or enclosure.
Keep fixture away from materials that may burn.
Do not operate the luminaire fitting with a missing or
damaged shield. Do not touch the source at any time. Use

a soft cloth or gloves. Oil from skin may cause damage.

SAVE THESE INSTRUCTIONS

· Suitable for wet locations

This product is available with field replaceable components. Exclusive interchangeable OPTIKITS and modular
LED components with quick disconnects simplifies upgrades and maintenance when necessary.

• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local and
Provincial Codes.

• Follow product label information and instructions.

• Qualified Personnel with appropriate personal protective
equipment must perform all servicing of this product.

• Before wiring to power supply and during servicing, turn off and
lock out power at fuse or circuit breaker before service.

• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause an
unsafe condition and void product warranty.

IMPORTANT LISTINGS AND CERTIFICATIONS

By Others

AND INSTALLATION INSTRUCTIONS

• Do not block light emanating from product in whole or part, as
this may cause an unsafe condition.

• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.

• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body.

• Replace LED assembly only with correct wattage and type of
power supply appropriate for LED assembly.

• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.

1. Use 5/64” Allen wrench to slightly loosen
three (3) #8-32 stainless steel set screws to remove
cap.

4. Gently lift LED module and disconnect from fixture.
Install new LED module. Secure set screws using
.050” Allen wrench.

Do not pull on connector or wiring. Handle with

care.

IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS

B-K LIGHTING

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.

2. Remove optic by pulling gently and lift up.

5. Replace optic by lining notches with optic holder,
then pressing down gently until secured into place.

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX [phone]

www.bklighting.com • [e-mail]

3. Use .050” Allen wrench to loosen three (3) set
screws holding LED module. Gently lift from fixture.

6. Place cap on fixture and tighten set
screws. Tighten screw to 1/2 in-lbs. Top
of screws should sit flush with fixture cap.

Warning: Do not over tighten set screws. Doing
so will compromise O-Ring seal and will void
warranty.

RELEASED

8-17-18

REFERENCE NUMBER

INS000011