BKI FKM-F Installation Manual
SS-OM-015.05 Revised 09/21/2018
Electric Pressure Fryer
MODELS FKM-F & FKM-FC
Installation and Operation Manual
Serial Numbers 811000 and higher
BKI LIMITED WARRANTY
2812 Grandview Dr. • Simpsonville, SC 29680 • USA
(864) 963-3471 • Toll Free: (800) 927-6887 • Fax: (864) 963-5316
WHAT IS COVERED This warranty covers defects in material and workmanship under normal use, and applies only to the
original purchaser providing that:
The equipment has not been accidentally or intentionally damaged, altered or misused;
The equipment is properly installed, adjusted, operated and maintained in accordance with national
and local codes, and in accordance with the installation and operating instructions provided with this
product.
The serial number rating plate affixed to the equipment has not been defaced or removed.
WHO IS COVERED This
warranty
is
extended
to the original
purchaser
and applies only to
equipment purchased
for use in the U.S.A.
COVERAGE PERIOD
Warranty claims must be received in writing by BKI within one (1) year from date of
installation or within one (1) year and three (3) months from data of shipment from the
factory, whichever comes first.
COB Models: One (1) Year limited parts and labor.
COM Models: Two (2) Year limited parts and labor. COM convection ovens also have a two (2)
year door warranty.
CO1 Models: Two (2) Year limited parts and labor. Five (5) Year limited door warranty.
BevLes Products: Two (2) Year limited parts and labor.
Warranty period begins the date of dealer invoice to customer or ninety (90) days after
shipment date from BKI, whichever comes first.
WARRANTY COVERAGE This
warranty
covers on-site labor, parts and
reasonable
travel
time
and travel e
xpenses
of the
authorized
service
representative
up to (100) miles
round
trip and (2)
hours
travel time and
performed during regular, weekday business hours.
EXCEPTIONS Any exceptions must be pre-approved in advance and in writing by BKI. The extended door warranty
on convection ovens years 3 through 5 is a parts only warranty and does not include labor, travel,
mileage or any other charges.
EXCLUSIONS
Negligence
or acts of
God,
Thermostat calibrations
after (30) days
from equipment installation date,
Air and gas
adjustments,
Light
bulbs,
Glass doors and
door adjustments,
Fuses,
Adjustments
to
burner
flames and
cleaning of
pilot
burners,
Tightening
of screws or
fasteners,
Failures
caused
by erratic
voltages
or gas
suppliers,
Unauthorized
repair by
anyone other than
a BKI F
actory Authorized
Service Center,
Damage
in
shipment,
Alteration,
misuse or
improper installation,
Thermostats
and safety valves with
broken
capillary tubes,
Freight –
other than normal UPS charges,
Ordinary
wear and
tear,
Failure to follow
installation and/or operating instructions,
Events
beyond control
of the
company.
INSTALLATION Leveling, as well as
proper installation
and check out of all
new equipment -
per
appropriate
installation
and use materials – is the responsibility of the
dealer
or installer, not the
manufacturer.
REPLACEMENT PARTS
BKI genuine
Factory OEM parts receive a (90) day
materials warranty
effective from the date of
installation
by a BKI F
actory Authorized
Service
Center.
Warranty
is in lieu of all
other warranties, expressed
or implied, and all
other obligations
or
liabilities on the
manufacturer’s
part. BKI shall in no
event
be liable for any
special, indirect
or
consequential damages,
or in any
event
for
damages
in excess of the
purchase
price of the
unit. The repair or
replacement
of
proven defective
parts shall
constitute a
fulfillment of all
obligations under
the terms of this
warranty
Electric Pressure Fryer Table of Contents
1
Table of Contents
Table of Contents ........................................................................................................................................ 1
Introduction ................................................................................................................................................. 2
Safety Precautions .................................................................................................................................... 2
Safety Signs and Messages ................................................................................................................. 2
Specific Precautions ............................................................................................................................. 3
Equipotential ground plane .............................................................................................................. 3
Full Disconnection ............................................................................................................................ 3
Safe Work Practices ............................................................................................................................. 4
Safety Labels ........................................................................................................................................ 8
Installation ................................................................................................................................................. 10
Unpacking and Handling ......................................................................................................................... 10
Installation Procedure ............................................................................................................................. 10
Wiring ...................................................................................................................................................... 11
Initial Test and Adjustment ..................................................................................................................... 12
Operation ................................................................................................................................................... 13
Controls and Indicators ........................................................................................................................... 13
Care of the Shortening ............................................................................................................................ 15
FKM-F Operation .................................................................................................................................... 16
System Programming ......................................................................................................................... 16
Product Programming ........................................................................................................................ 18
Start-Up (FKM-F) ................................................................................................................................ 19
Cooking (FKM-F) ................................................................................................................................ 20
FKM-FC Operation ................................................................................................................................. 22
System Programming ......................................................................................................................... 22
Product Programming ........................................................................................................................ 25
Start-Up (FKM-FC) ............................................................................................................................. 28
Cooking (FKM-FC) ............................................................................................................................. 29
Maintenance .............................................................................................................................................. 31
Scheduled Maintenance ......................................................................................................................... 31
Safety Pop Valve Procedure .............................................................................................................. 32
Filtering Procedure ............................................................................................................................. 33
Boil-Out Procedure ............................................................................................................................. 35
Filter Pad Replacement ...................................................................................................................... 37
Troubleshooting ...................................................................................................................................... 38
Notes .......................................................................................................................................................... 40
BKI Worldwide is a wholly owned subsidiary of Standex International Corporation
Electric Pressure Fryer Introduction
2
Introduction
The FKM Pressure Fryer is compact, attractive and functional in design. It is constructed of a stainless
steel fryer pot for cleaning ease. Exclusive BKI patented features and safety devices offer flexibility,
efficiency and reliability plus PERFECTION IN PRESSURE FRYING!
The BKI name and trademark on this unit assures you of the finest in design and engineering -- that it has
been built with care and dedication -- using the best materials available. Attention to the operating
instructions regarding proper installation, operation, and maintenance will result in long lasting
dependability to insure the highest profitable return on your investment.
PLEASE READ THIS ENTIRE MANUAL BEFORE OPERATING THE UNIT. If
you have any questions, please contact your BKI Distributor. If they are unable to
answer your questions, contact the BKI Technical Service Department, toll free:
1-800-927-6887. Outside the U.S., call 1-864-963-3471.
Safety Precautions
Always follow recommended safety precautions listed in this manual. Below is the safety alert symbol.
When you see this symbol on your equipment, be alert to the potential for personal injury or property
damage.
Safety Signs and Messages
The following Safety signs and messages are placed in this manual to provide instructions and identify
specific areas where potential hazards exist and special precautions should be taken. Know and
understand the meaning of these instructions, signs, and messages. Damage to the equipment, death or
serious injury to you or other persons may result if these messages are not followed.
This message indicates an imminently hazardous situation which, if not avoided,
will result in death or serious injury.
This message indicates a potentially hazardous situation, which, if not avoided,
could result in death or serious injury.
This message indicates a potentially hazardous situation, which, if not avoided,
may result in minor or moderate injury. It may also be used to alert against
unsafe practices.
This message is used when special information, instructions or identification are
required relating to procedures, equipment, tools, capacities and other special
data.
Electric Pressure Fryer Introduction
3
Specific Precautions
Risk of fire exists if the oil level drops below 5mm of the maximum oil level.
Use of oil/shortening older than the manufacturers recommendations for life of the
oil is prone to surge boiling and flash fires. Follow the oil manufacturers
guidelines for the life cycle of oil/shortening.
Do not open the drain valve or the fill valve while the fryer is under pressure.
Serious burns may result.
California Residents Only
This product can expose you to chemicals including chromium, and lead which
are known to the State of California to cause cancer and birth defects or other
reproductive harm. For more information go to www.P65Warnings.ca.gov.
Follow instructions regarding effects of surge boiling of over-wet foods and proper
load size.
This unit incorporates components that contain Mercury. The use of Mercury
relays is an industry standard.
Equipotential ground plane
When a high current flows through a conductor, differences in potential appear
between the conductor and nearby metallic surfaces near the appliance. As a
result, sparks may be produced between the appliance and surrounding metal
surfaces. These sparks could cause serious injury, damage, or fire.
BKI provides an Equipotential ground terminal for the connection of a bonding
conductor after the installation of the appliance per lEC60417-1. This terminal is
located on the inside of the Power Entry Supply box near the Earth connection
and is marked with this symbol.
Full Disconnection
In accordance with Local and/or National wiring codes, the installer must provide
a means of full disconnection under over voltage Category III conditions. An IEC
approved cord and plug combination will meet this requirement.
Units not provided with a cord and plug do not meet this requirement. In
accordance with Local and/or National wiring codes, the installer must provide the
means of full disconnection.
The fryer is designed to hold a maximum of 75lbs (34KG) of oil/shortening.
Electric Pressure Fryer Introduction
4
Safe Work Practices
Noncombustible Floors Only
Make sure your floor is noncombustible. Do not operate your fryer
on floors that are wood, carpeted or have rubber mats.
• Placing your fryer on a combustible floor could cause a
fire. Serious injury could result.
• Examples of noncombustible floors where you can safely
place your fryer are concrete, tile, and ceramic.
Keep The Area Around Your Fryer Uncluttered
Make sure to keep the area around your fryer clear of any
obstacles.
Serious injury can occur if you trip or fall near the fryer. You could
be burned by hot shortening that splashes out of the fryer or by
falling against the hot metal of the fryer.
Keep The Floor Around Your Fryer Clean Of Shortening
Make sure to keep the floor around your fryer clean of shortening
and other liquids.
Serious injury can occur if you slip near your fryer. You could be
burned by hot shortening that splashes out of the fryer or by
falling against the hot metal of the fryer.
Keep The Lid Closed When The Fryer Is Not In Use
Hot shortening can splash if someone moves the fryer or bumps
into it. Serious injury can occur if hot shortening splashes out of
the fryer.
Do not lean, sit or stand on the fryer or perform any maintenance
or cleaning duties while the fryer or the shortening is hot. You
could be burned.
Keep The Casters Locked
To avoid spilling shortening, keep the casters locked. If any
shortening spills near your fryer, clean it up immediately.
Electric Pressure Fryer Introduction
5
Do Not Overfill The Fryer With Shortening
Hot shortening and steam may escape and burn you if you put
too much shortening in the fryer. Fill the fryer to approximately
one inch below the fill marks that are inside the fryer pot. Heat the
shortening. If needed, carefully add more shortening to bring the
level to the fill marks.
Do Not Let Any Water Get Into The Fryer
Always remove excess moisture from food before placing it into
the fryer basket. Water will cause the hot shortening to spatter.
You could be burned.
Do Not Overload The Basket With Food
Hot shortening and steam may escape and burn you if you place
too much food in the basket.
Always Make Sure The Lid Hook Is Latched When Closing
The Fryer
To make sure the lid hook is latched properly, press down the lid
until the hook snaps shut. Hot shortening and steam can escape
if the lid hook is not latched properly. You could be burned.
Keep Away From The Vent
Hot steam escapes from the vent continuously when you are
using your fryer. You could be burned if you get too close to the
vent.
Seal The Safety Valve Properly
To seal the safety valve, lift the arm on the side of the valve. Then
release it. The valve should snap closed. Hot steam can escape
from the valve and you could be burned if you do not seal the
valve properly.
Always Tighten The Spin Handle When Closing The Fryer
Hot shortening and steam can escape if you do not tighten the
spin handle properly. You could be burned. Line up the orange
knobs on the fryer lid handle and the front hook when tightening.
Do Not Over-Tighten The Spin Handle
You could damage the fryer.
Electric Pressure Fryer Introduction
6
Wear Safe Clothing Appropriate To Your Job
Always wear your insulated mitts when handling the fryer basket
or touch any hot metal surfaces. You received a pair of insulated
mitts with your fryer. If you lose or damage your mitts, you can
buy new ones at your local restaurant equipment supply store or
from your local BKI Distributor.
Always wear non-skid shoes when working around the fryer or
any other equipment that uses shortening. Never wear loose
clothing such as neckties or scarves while operating your fryer.
Keep loose hair tied back or in a hair net while operating your
fryer.
Always wear appropriate personal protection equipment during
the filtering process to guard against possible injury from hot oil.
Always wear appropriate personal protection equipment during
the boil-out process to guard against possible injury from hot
cleaning solution.
Never Loosen The Spin Handle Until The Pressure Gauge Is
At Zero
Steam may escape suddenly if you loosen the spin handle before
the gauge is at zero. If steam escapes suddenly, you could be
burned.
After the pressure gauge is at zero, wait 5 seconds. Then loosen
the spin handle slowly to open the lid of the fryer. By doing this,
the steam will escape slowly and there is less change of being
burned. Always use extreme caution when working around the
fryer with the lid open.
Keep this manual with the Equipment
This manual is an important part of your equipment. Always keep
it near for easy access.
If you need to replace this manual, contact:
BKI
Technical Services Department
2812 Grandview Drive
Simpsonville, S.C. 29680
Or call toll free: 1-800-927-6887
Outside the U.S., call 864-963-3471
Protect Children
Keep children away from this equipment. Children may not
understand that this equipment is dangerous for them and others.
NEVER allow children to play near or operate your equipment.
Electric Pressure Fryer Introduction
7
Keep Safety Labels Clean and in Good Condition
Do not remove or cover any safety labels on your equipment.
Keep all safety labels clean and in good condition. Replace any
damaged or missing safety labels. Refer to the Safety Labels
section for illustration and location of safety labels on this unit.
If you need a new safety label, obtain the number of the specific
label illustrated on page 8, then contact:
BKI
Technical Services Department
2812 Grandview Drive
Simpsonville, S.C. 29680
Or call toll free: 1-800-927-6887
Outside the U.S., call 864-963-3471
Be Prepared for Emergencies
Be prepared for fires, injuries, or other emergencies.
Keep a first aid kit and a fire extinguisher near the equipment.
You must use a 40-pound Type BC fire extinguisher and keep it
within 25 feet of your equipment.
Keep emergency numbers for doctors, ambulance services,
hospitals, and the fire department near your telephone.
Know your responsibilities as an Employer
• Make certain your employees know how to operate the
equipment.
• Make certain your employees are aware of the safety
precautions on the equipment and in this manual.
• Make certain that you have thoroughly trained your employees
about operating the equipment safely.
• Make certain the equipment is in proper working condition. If
you make unauthorized modifications to the equipment, you
will reduce the function and safety of the equipment.
Electric Pressure Fryer Introduction
8
Safety Labels
Electric Pressure Fryer Introduction
9
Electric Pressure Fryer Installation
10
Installation
Serious injury, equipment damage or death could result if attempting to install
this fryer yourself. Ensure that an authorized BKI service agent installs the fryer.
Unpacking and Handling
It is the owners’ responsibility to file all freight claims with the delivering truck line. Inspect all cartons and
crates for damage as soon as they arrive. If damage to cartons or crates is found, or if a shortage is
found, note this on the bill of lading (all copies) prior to signing.
If damage is found when the equipment is opened, immediately call the delivering truck line and follow up
the call with a written report indicating concealed damage to your shipment. Ask for an immediate
inspection of your concealed damage item. Packaging material MUST be retained to show the inspector
from the truck line.
Installation Procedure
1. Remove all packing materials from the interior and exterior of the fryer.
2. Remove the shipping packing clip from underneath the dead weight cap and discard.
3. Replace the dead weight and cover.
Risk of electric shock – Fryer must be secured to building structure. Follow
restraining device instructions for proper installation.
4. Install an ANSI Z83.11/CGA 1.8 compliant restraining device (such as BKI part number FT0279)
per the instructions below:
• Mount the wall attachment according the restraining device manufacturer instructions.
• Attach the spring-loaded hook on the restraining device to the eye-bolt mounted to the fryer
then attach the other spring-loaded hook to the wall attachment.
Electric Pressure Fryer Installation
11
5. Lock the casters so the fryer does not move. Every time the fryer is used, make sure the casters
are locked so the fryer cannot move.
6. Clean the fryer pot before filling with shortening.
7. Place the DRAIN handle in the CLOSED position.
Wiring
Electrocution, equipment failure or property damage could result if an unlicensed
electrician performs the electrical installation. Ensure that a licensed electrician
performs the electrical installation in accordance with local codes, or in the
absence of local codes, with the National Electrical Code, ANSI NFPA 70-20XX.
This unit, when installed by an authorized BKI service agent, must be wired for use in accordance with all
applicable local, state, and federal codes. For specific electrical requirements and connections refer to the
wiring diagram attached to the unit or provided in the Service Manual.
Loading...