by Bkav
MODEL: SH - CTxRZW
USER GUIDE
TOUCH SWITCH
SH - CTxRZW
Bkav SmartHome technology company limited
Usage notice
Thank you for choosing touch switch SH – CTxRZW of Bkav
SmartHome. By selecting Bkav SmartHome’s products, you
will get the best warranty service and installation support
from our technicians.
This document gives useful information during installation
and usage time. You should read and keep the manual
carefully in case of need.
Electric shock may cause injuries or threats to
life. Before installing, repairing or cleaning the
device, you should check whether the device’s
power is disconnected.
This work should be done by technicians or
Warning
Customer Contact Center to avoid electric
related accidents.
Environmental regulations must be complied when
discarding or recycling the device or its wrapping.
1
2
The touch switch SH - CTxRZW is the product of Bkav
SmartHome and has been registered regarding design,
utility solutions and quality certification. All violations such as
copies of design and product idea are subject to the current
copyright law of the Socialist Republic of Vietnam.
Copyright © 2015 Bkav SmartHome Co., Ltd. All rights reserved.
Table of contents
3
Usage notice
Table of contents
Safety instruction
Introduction
General introduction
Product package
Specifications
Wiring diagram
Installation instruction
Device usage
Function of direct control
Function of advanced features
How to restore default mode
Software installation
Contact
1
3
4
5
5
6
7
8
9
12
13
13
14
15
16
4
Safety instruction
Do not use voltage which is different from the one
stated in the device’s specifications.
Disconnect device’s power prior to any installation,
disassembly or repair.
Do not leave the device in high-temperature
environment.
Do not disassemble the device if not necessary.
Do not clean the device with corrosive chemicals.
Safety instruction should be complied during the
device usage.
Warning
Introduction
General introduction
The touch switch SH - CTxRZW (*) is used to turn on/off
from 1 to 4 on/off channels. With the design of the
capacitive touch technology, anti-scratch Gorilla Glass,
unibody aluminum, the device will make your house convenient
and luxurious.
Besides, Wi-Fi or ZigBee connection makes it easier to install
the device in existing houses or brand new ones without
re-arranging electric lines or changing their infrastructure.
The device is suitable to control home appliances such as
night lamps, fans, televisions, curtains, blinds, etc.
(*) Model SH - CTxR: X is the quantity of controlled
channels of the device
(from 1 to 4 channels)
(*) Model SH - CTxRZ: The device uses ZigBee technology.
Notice
(*) Model SH - CTxRW: The device uses Wi-Fi technology.
5
6
Product package
Touch-screen
control panel
Power circuit box
by Bkav
Receptacle box
Connecting
cable
User guide (book) Set of screws
MODEL: SH - CTxRZW
Specifications
Operating voltage
7
100-240V 50/60Hz
Wi-Fi band
ZigBee frequency 2.4GHz
Operating temperature
Power rating
Dimensions (L x W x H)
Weight
2.4GHz - 802.11b/g/n
60ºC max
5A max/1 channel
97 x 93 x 43 mm
240 gram
8
N
100-240V 50/60Hz
L
* The quantity of channel depends on the product type of 1, 2, 3 or 4 buttons
(refer to page 05)
Wiring diagram
Made by SmartHome
Made in Vietnam
by Bkav
Smart touch switch
Model: SH - CT4RZW-P
Disconnect device’s power prior to installation.
100-240
VAC
N
L
Voltage:
Power rating:
Operating temperature:
100-240V 50/60Hz
OUT
OUT
OUT
OUT
1.2
1.1
COMCOM
2.2
2.1
4321
5A max
60ºC max
Installation instruction
Step 1: Connect the unconnected wires (2) from Receptacle
box (1) to Power circuit box (3) as in Figure 1 based on the
wiring diagram at page 8.
3
Power circuit box
2
Unconnected wire
1
Receptacle box
1
9
10
Step 2: Insert Power circuit box (3) into Receptacle box (1)
following the direction of the arrow, tighten 4 M4 screws (4)
to fix as shown in Figure 2.
Notice: Wire connector is always installed upwards.
Receptacle box
1
Wire connector
3
Power circuit box
4
M4 screw
2
Step 3: Connect the connecting cable (5) to Power circuit
box (3), then connect another cable’s head with the
Touch-screen control panel (6). Push the Touch-screen
control panel (6) towards the Power circuit box (3).
The green part of the connecting cable’s head is
Notice
always in an upward direction on connecting
1
Receptacle box
Power circuit box
3
5
Connecting cable
Touch-screen
6
control panel
3
11
12
Device usage
Touch control button (*)
Status indicator light
(*) The quantity of channel depends on the product type of 1, 2, 3 or 4 buttons
(refer to page 05)
Function of direct control
SH - CTxRZW uses the capacitive touch technology to turn
on/off electric devices just by gently tapping on the
corresponding icon on the glass. The indicator below the
icon is on, the corresponding status of the device is on. The
indicator below the icon is off, the corresponding status of
the device is off.
Function of advanced features
With control via Wi-Fi or ZigBee, SH – CTxRZW can get
commands from control interfaces which are set up in the
devices such as mobiles, tablets.
Besides, SH - CTxRZW can operate automatically based on
scenarios, schedules which are set up via software or operate
based on smart room system when connecting to other
devices.
13
14
How to restore default mode
To restore the default mode of the device, please follow ether
of the following ways:
Press and hold button 1 on the device for 15 seconds.
Use the function of default mode restoration of the device
on the control software.
Notice
Button 1:
The button on the left or the button on top
left of the device.
Software installation
You can download Bkav SmartDevice software to control the
device at: http://www.smarthome.bkav.com/SmartDevice
or scan QR Code below to download the application.
15
16
If there is any problem related to the product, please contact
Customer Contact Center:
Customer Contact Center: (+1) 202 386 6779
Email: GlobalProject@bkav.com
Contact
The new home standard !
www.smarthome.bkav.com
Copyright © 2015 Bkav SmartHome Co., Ltd. All rights reserved.
Mfr Code: 893604393HDCTxRZW
UGCTxRZW/V1.0/0115
Loading...