BIXOLON SLP-D420E, SLP-D423, SLP-D423E Programming Manual

Programming Manual

SLCS

Rev. 1.02

SLP-D420 / D420E
SLP-D423 / D423E

http://www.bixolon.com

SLCS Programming Manual

Rev. 1.02

- 2 -

■ Table of Contents

1. Foreword ........................................................................................................................ 4

1-1 Image Buffer Configuration ..................................................................................... 5

1-2 Information for calculating position on image buffer ............................................ 6

1-3 Command List ........................................................................................................... 8

1-4 Programming Considerations ............................................................................... 10

2. Detail Description ........................................................................................................ 11

2-1 Commands for Designing a Label ......................................................................... 11

2-1-1 T (Text String) ..................................................................................................... 12

2-1-2 V (Text String Vector Font) .................................................................................. 15

2-1-3 B1 (1 Dimensional bar code) .............................................................................. 18

2-1-4 B2 (2 Dimensional bar code) .............................................................................. 21

2-1-5 B3 (Special Barcode) .......................................................................................... 25

2-1-6 BD (Block Draw) ................................................................................................. 26

2-1-7 CD (Circle Draw) ................................................................................................ 29

2-1-8 CS (Character Set selection) .............................................................................. 30

2-1-9 P (Print) .............................................................................................................. 33

2-2 Media & Buffer Related Commands ...................................................................... 35

2-2-1 ST (Set Printing Type) ........................................................................................ 36

2-2-2 SM (Set Margin) ................................................................................................. 36

2-2-3 SF (Set Back-Feed Option) ................................................................................ 38

2-2-4 SL (Set Length) .................................................................................................. 39

2-2-5 SW (Set Width) ................................................................................................... 42

2-2-6 SB (Set Buffer mode) ......................................................................................... 43

2-2-7 CB (Clear Buffer) ................................................................................................ 43

2-3 Printer Setting Commands..................................................................................... 44

2-3-1 SS (Set Speed) ................................................................................................... 45

2-3-2 SD (Set Density) ................................................................................................. 45

2-3-3 SO (Set Orientation) ........................................................................................... 46

2-3-4 SP (Set Port) ...................................................................................................... 47

2-3-5 SA (Set Offset) .................................................................................................... 48

2-3-6 TA (Tear-off/Cutter Position Setting) ................................................................... 48

2-4 Variable Related Commands ................................................................................. 49

2-4-1 SC (Set Counter) ................................................................................................ 50

2-4-2 AC (Auto Counter) .............................................................................................. 51

2-4-3 SV (Set Variable) ................................................................................................ 52

2-4-4 ? (Get Variables) ................................................................................................. 53

2-4-5 PV (Print with Variables) ..................................................................................... 54

2-5 Template Related Commands ................................................................................ 55

2-5-1 TS (Template store Start) .................................................................................... 56

2-5-2 TE (Template store End) ..................................................................................... 56

2-5-3 TR (Template Recall) .......................................................................................... 57

2-5-4 TD (Template Delete) ......................................................................................... 58

2-5-5 TI (Template Information).................................................................................... 58

SLCS Programming Manual

Rev. 1.02

- 3 -

2-6 Image Related Commands ..................................................................................... 59

2-6-1 IS (Image Store) ................................................................................................. 60

2-6-2 IR (Image Recall) ................................................................................................ 60

2-6-3 ID (Image Delete) ............................................................................................... 61

2-6-4 II (Image Information) ......................................................................................... 61

2-6-5 LD ................................ ................................ ................................ ....................... 62

2-6-6 LC ................................ ................................ ................................ ....................... 64

2-6-7 BMP .................................................................................................................... 66

2-7 Downloadable font Related Commands ............................................................... 67

2-7-1 DT (Download True Type Font) .......................................................................... 68

2-7-2 DD (Downloaded font Delete) ............................................................................. 69

2-7-3 DI (Downloaded font Information) ....................................................................... 70

2-8 The Others ............................................................................................................... 71

2-8-1 @ (Initialize Printer) ............................................................................................ 72

2-8-2 PI (Printer Information) ....................................................................................... 72

2-8-3 CUT (Auto-cutter Enable/Disable) ...................................................................... 73

2-8-4 ^cp (Check Printer Status and Report 2 bytes) ................................................... 74

2-8-5 ^cu (Check Printer Status and Report 1 byte) ..................................................... 75

2-8-6 ^PI (Send Printer information to host) ................................................................. 76

2-8-7 ^MBZ (Power Save mode setting) ...................................................................... 77

2-8-8 ^MBP (Send power Save mode information to host) .......................................... 77

3. Programming Example ................................................................ ................................ 78

3-1 Example) T_resident ............................................................................................... 78

3-2 Example) T_Rotate4................................................................................................ 79

3-3 Example) V_resident .............................................................................................. 80

3-4 Example) V_Rotate4 ............................................................................................... 81

3-5 Example) Code39 .................................................................................................... 82

3-6 Example) BD1.......................................................................................................... 83

3-7 Example) BD3.......................................................................................................... 84

3-8 Example) BD4.......................................................................................................... 86

3-9 Example) BD5.......................................................................................................... 87

3-10 Example) Slope ..................................................................................................... 88

3-11 Example) SW&SL ................................................................................................ .. 89

3-12 Example) TEST00_TS ........................................................................................... 91

3-13 Example) TEST00_TR ........................................................................................... 92

3-14 Example) TEST04_TS ........................................................................................... 93

3-15 Example) TEST04_TR ........................................................................................... 94

3-16 Example) IR1 ......................................................................................................... 94

3-17 Example) TEST10_TS ........................................................................................... 95

3-18 Example) TEST10_TR ........................................................................................... 95

3-19 Example) TEST11_TS ........................................................................................... 96

3-20 Example) TEST11_TR ........................................................................................... 96

3-21 Example) SLCS_BIXOLON ................................................................................... 97

SLCS Programming Manual

Rev. 1.02

- 4 -

1. Foreword

In this chapter, the basic concept of SLCS and some information necessary for the
programmer to use SLCS will be explained. Please read this part before starting
programming for efficient and easy use of BIXOLON Label Printers..

We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and
quality of all our products. In following, product specifications and/or user manual content
may be changed without prior notice.

SLCS Programming Manual

Rev. 1.02

- 5 -

1-1 Image Buffer Configuration

1) Maximum size

A) When using Double Buffering Function

832dots × 1216dots (104mm × 152mm) = 4 inch × 6 inch
B) When using Single Buffering Function
832dots × 2432dots (104mm × 304mm) = 4 inch × 12 inch

2) Dot size : 0.125mm(W) × 0.125mm(H) (203dpi)

…

.
.
.

.
…
.

.
.
.

…

832 dots(104mm = 4inch)

1216 dots(152mm = 6inch)

Image Buffer

SLCS Programming Manual

Rev. 1.02

- 6 -

1-2 Information for calculating position on image buffer

1) Relation between position and number of dots

2) Font Information

Inch

mm

dots

Resolution

0.04 1 8

203 dpi

0.40

10.00

80

1.00

25.40

203

1.25

31.75

254

1.50

38.10

305

1.75

44.45

355

2.00

50.80

406

2.25

57.15

457

2.50

63.50

508

2.75

69.85

556

3.00

76.20

610

4.00

101.6

813

Font name

Width × Height (dots)

0

09 ×15

1

12 × 20

2

16 × 25

3

19 × 30

4

24 × 38

5

32 × 50

6

48 × 76

7

22 × 34

8

28 × 44

9

37 × 58

Korean a

16 × 16(ascii:9×15)

Korean b

24 × 24(ascii:12×24)

Korean c

20 × 20(ascii:12×20)

Korean d

26 × 26(ascii:16×30)

Korean e

20 × 26(ascii:16×30)

Korean f

38 × 38(ascii:22×34)

GB2312 m

24 × 24(ascii:12×24)

BIG5 n

24 × 24(ascii:12×24)

Vector

Scalable

SLCS Programming Manual

Rev. 1.02

- 7 -

3) Example of text and barcode

4) Example of rotation

BIXONOL

SLPD420

(0.0)

Direction of x axis

Direction of y axis

(124 , 160)

(503 , 160)

(124 , 356)

(0.0)

Direction of x axis

ＡＢＣＤ

ＡＢＣＤ

ＡＢＣＤ

Start Position

0°

Start Position

270°

Start Position

90°

Start Position

180°

SLCS Programming Manual

Rev. 1.02

- 8 -

1-3 Command List

Command

Description

Remarks

Page

1. Commands for Designing Label

T

Text

Draw text string on the image buffer

V

Text (Vector Font)

Draw text string on the image buffer

B1

1d barcode

Draw 1D Barcode on the image buffer

B2

2d barcode

Draw 2D Barcode on the image buffer

B3

Special barcode

Draw special barcode on the image buffer

BD

Block Draw

Draw line or box on the image buffer

CD

Circle Draw

Draw circle on the image buffer

CS

Character Set selection

Select international code table

P

Print

Start printing the content of image buffer

2. Media & Buffer related Commands

ST

Set Print Type

Select Thermal Direct / Transfer printing

SM

Set Margin

Set the marginal value of the image buffer

SF

Set Back-feed Option

Set back-feeding option

SL

Set Label Length

Set length of label

SW

Set Label Width

Set length of label

SB

Set Buffer mode

Enable or Disable double buffering
function

CB

Clear Buffer

Clear image buffer

3. Printer Setting Commands

SS

Set Speed

Set printing speed

SD

Set Density

Set printing density from level 0 to 20

SO

Set Orientation

Set printing direction

SP

Set serial Port

Set serial port configurations

SA

Set Offset

Set offset value

TA

Set Tear-off/Cut

Set Tear-off/Cut value

4. Variable related Commands

SC

Set Counter

Used in Template sequence

AC

Set Counter

Used in normal mode

SV

Set Variable

Used in Template sequence

?

Get variables

Get content of variables and counters

PV

Print with Variable

Use this command in Template

SLCS Programming Manual

Rev. 1.02

- 9 -

Command

Description

Remarks

Page

5. Template Related Commands

TS

Template store Start

All contents between these commands are
saved in printer memory

TE

Template store End

TR

Template Recall

Load and reuse the stored Template

TD

Template Delete

Delete stored Template from printer
memory

TI

Template Information

Print the list of currently stored Templates

6. Image Data Related Commands

IS

Image Store

PCX format image file can be stored

IR

Image Recall

Load and reuse the stored image

ID

Image Delete

Delete stored image

II

Image Information

Print the list of currently stored images

LD

Bitmap data draw

Draw bitmap image data on the image
buffer

LC

Compression bitmap data

draw

Draw compression bitmap image data on
specific position of image buffer

BMP

BMP format file draw

Draw BMP format file on the image buffer

7. Downloadable Font Related Commands

DS

Download Bitmap font

User made Bitmap font

DT

Download True Type font

Windows system font used

DD

Downloadable font Delete

Delete downloaded font

DI

Downloadable font
Information

Print the list of currently stored images

8. The Others

@

Reset printer

Initialize the printer

PI

Printer Information

Print current setting of printer

CUT

Enable/Disable Cutter option

Cutting is executed after Printing is finished
if cutting option is enabled by this
command

^cp

Check Printer Status

Return 2 bytes status values to host

^cu

Check Printer Status

Return 1 byte status value to host

^PI

Send Printer information

Send various information to host

^MBZ

Power save mode setting

To set the power save mode

^MBP

Transmit power save mode
setting information

To send the power save mode setting
values to the host

SLCS Programming Manual

Rev. 1.02

- 10 -

1-4 Programming Considerations

1) All commands are case-sensitive and some commands require one or more parameters

and „Data‟.

2) Command Conventions

Tp1,p2,p3,p4,p5,p6,p7,p8,p9,‟TEXT DATA‟

Parameters Command Specific Data

Command

3) Each command line must be terminated with a „CR‟(0Dh, 13) + „LF‟(0Ah,10).

4) The commands which draw text, barcode, lines… just draw on the image buffer, they do

not start printing. The printer will start printing when the P command comes.

! Caution

The „P‟ command must be terminated by „CR‟(0x0d). If not, the printer will not start

printing until „CR‟ comes.

SLCS Programming Manual

Rev. 1.02

- 11 -

2. Detail Description

2-1 Commands for Designing a Label

These commands are used to design a label by providing text, barcode, line, box… and to
print content of image buffer on media.

1) T

Draw Text String on the image buffer.

2) V

Draw Text (Vector Font) String on the image buffer.

3) B1

Draw 1D Barcode on the image buffer.

4) B2

Draw 2D Barcode on the image buffer.

5) B3
Draw Special Barcode on the image buffer.

6) BD

Draw Line, Block, Box & Slope on the image buffer.

7) CD

Draw Circle on the image buffer.

8) CS

Set Code page and ICS(International Character Set).

9) P

Start printing the content of the image buffer.

SLCS Programming Manual

Rev. 1.02

- 12 -

2-1-1 T (Text String)

Description

Draw text string on the image buffer

Syntax

Tp1,p2,p3,p4,p5,p6,p7,p8,p9(,p10),‟DATA‟

Parameters

p1 : Horizontal position (X) [dot]
p2 : Vertical position (Y) [dot]
p3 : Font selection

Value

Font Size(pt)

Width  Height(dots)

0

6

9  15

1

8

12  20

2

10

16  25

3

12

19  30

4

15

24  38

5

20

32  50

6

30

48  76

7

14

22  34

8

18

28  44

9

24

37  58

a

KOREAN 1

16  16 (ascii 915)

b

KOREAN 2

24  24 (ascii 1224)

c

KOREAN 3

20  20 (ascii 1220)

d

KOREAN 4

26  26 (ascii 1630)

e

KOREAN 5

20  26 (ascii 1630)

f

KOREAN 6

38  38 (ascii 2234)

m

GB2312

24  24 (ascii 1224)

n

BIG5

24  24 (ascii 1224)

j

Shift JIS

24  24 (ascii 1224)

 A to Z are assigned to Downloadable font. Refer to DS command.

p4 : Horizontal multiplier : 1 ~ 4
p5 : Vertical multiplier : 1 ~ 4
p6 : Right-side character spacing [dot]

Plus(+)/Minus(-) option can be used. Ex) 5, +3, -10…

p7 : Rotation

Value

Rotation

0

No Rotation

1

90 degrees

2

180 degrees

3

270 degrees

p8 : Reverse printing

N : Normal printing R : Reverse printing

SLCS Programming Manual

Rev. 1.02

- 13 -

p9 : Bold

N : Normal B : Bold

p10 : Text Alignment(Optional)

F : p1 means the position of the first character in text string - Left alignment

L : p1 means the position of the last character in text string - Right alignment

R: Write text sting form right to left.

(BIXOLON → NOLOXIB)

 This parameter is for alignment of text lines.

„DATA‟ : The various data types can be used in the data field as followings.

1) Fixed text string : „ Text String‟

2) Variables declared in template by SV command : Vnn

3) Counters declared by the SC command : Cn

 1) , 2) and 3) can be mixed together

Example

T50,100,3,1,1,0,0,N,N,‟ BIXOLON Label Printer‟
T50,100,3,1,1,0,0,N,N,‟Manufacturer :‟V00

T50,100,3,1,1,0,0,N,N,V00
T50,100,3,1,1,0,0,N,N,‟Manufacturer :‟C0
T50,100,3,1,1,0,0,N,N,C0

 If you want to print ‟ or \ then you must type like \‟ or \\ .

SLCS Programming Manual

Rev. 1.02

- 14 -

Example

SM20,20

T26,20,0,0,0,0,0,N,N,‟Font- 6 pt‟
T26,49,1,0,0,0,0,N,N,‟Font - 8 pt‟
T26,81,2,0,0,0,0,N,N,‟Font - 10 pt‟
T26,117,3,0,0,0,0,N,N,‟Font - 12 pt‟
T26,156,4,0,0,0,0,N,N,‟Font - 15 pt‟
T26,200,5,0,0,0,0,N,N,‟Font - 20 pt‟
T26,252,6,0,0,0,0,N,N,‟Font - 30 pt‟

P1

Result

Font – 6 pt

Font – 8 pt

Font – 10 pt

Font – 12 pt

Font – 15 pt

Font – 20 pt

Font – 30 pt

SLCS Programming Manual

Rev. 1.02

- 15 -

2-1-2 V (Text String Vector Font)

Description

Draw text (Vector Font) string on the image buffer

Syntax

Vp1,p2,p3,p4,p5,p6,p7,p8,p9,p10,p11,p12, ‟DATA‟

Parameters

p1 : Horizontal position (X) [dot]
p2 : Vertical position (Y) [dot]
p3 : Font selection

U: ASCII (1Byte code)

K: KS5601 (2Byte code)
B: BIG5 (2Byte code)
G: GB2312 (2Byte code)
J: Shift-JIS (2Byte code)

a: OCR-A (1Byte code)

b: OCR-B (1Byte code)

p4 : Font width (W)[dot]
p5 : Font height (H)[dot]
p6 : Right-side character spacing [dot]

Plus (+)/Minus (-) option can be used. Ex) 5, +3, -10…
P7 : Bold

N : Normal B : Bold

p8 : Reverse printing

N: Normal printing R: Reverse printing

P9 : Text style

N: Normal I: Italic

P10 : Rotation

Value

Rotation

0

No Rotation

1

90 degrees

2

180 degrees

3

270 degrees

p11: Text Alignment (Optional)

L: p1 means the position of the first character in the text string - Left alignment
R: p1 means the position of the last character in the text string - Right alignment
C: p1 means the position of the center character in the text string - Center alignment

SLCS Programming Manual

Rev. 1.02

- 16 -

p12: Text string write direction

0: Write text string form left to right (BIXOLON)

1: Write text string form right to left (NOLOXIB)

„DATA‟: The various data types can be used in the data field as follows.

1) Fixed text string: „Text String‟

2) Variables declared in template by SV command: Vnn

3) Counters declared by the SC command: Cn

 1), 2), and 3) can be mixed together.

Example

V50,100,U,25,25,+1,N,N,N,0,L,0,'BIXOLON Label Printer'
V50,200,U,35,35,-1,N,N,N,0,L,0, ‟Manufacturer :‟V00
V50,300,U,35,35,+1,B,R,I,0,L,0, V00

V50,400,U,45,25,+1,N,N,N,0,L,0,'Vector Font Test' C0
V50,500,U,25,45,+1,N,N,N,0,L,0, C0

V50,600,a,25,45,+1,N,N,N,0,L,0, ‘OCR-A font test’

 To print ‟ or \, \‟ or \\ must be typed.

SLCS Programming Manual

Rev. 1.02

- 17 -

Example

V50,100,U,25,25,+1,N,N,N,0,L,0,'Vector Font Test'
V50,200,U,35,35,-1,N,N,N,0,L,0,'Vector Font Test'
V50,300,U,35,35,+1,B,R,I,0,L,0,'Vector Font Test '
V50,400,U,45,25,+1,N,N,N,0,L,0,'Vector Font Test'
V50,500,U,25,45,+1,N,N,N,0,L,0,'Vector Font Test'
V50,700,U,65,65,+1,N,N,N,0,L,0,'ABCDEFGHIJKLMNO'
V50,900,U,65,65,+1,N,N,N,0,L,0,'abcdefghijklmno'
P1

Result

SLCS Programming Manual

Rev. 1.02

- 18 -

2-1-3 B1 (1 Dimensional bar code)

Description

Draw 1D Barcode on the image buffer

Syntax

B1p1,p2,p3,p4,p5,p6,p7,p8(,p9),‟DATA‟

Parameters

p1 : Horizontal position (X) [dot]
p2 : Vertical position (Y) [dot]
p3 : Barcode selection

p3

Barcode

p3

Barcode

0

Code39

5

UPC-A

1

Code128

6

UPC-E

2

I2of5

7

EAN13

3

Codabar

8

EAN8

4

Code93

9

UCC/EAN128

p4 : Narrow bar width [dot]
p5 : Wide bar width [dot]
p6 : Bar code height [dot]
p7 : Rotation

Value

Rotation

0

No Rotation

1

90 degrees

2

180 degrees

3

270 degrees

p8 : HRI (Human Readable Interpretation)

0 : Not printed
1 : Below the bar code(Font Size : 1)
2 : Above the bar code(Font Size : 1)
3 : Below the bar code(Font Size : 2)
4 : Above the bar code(Font Size : 2)
5 : Below the bar code(Font Size : 3)
6 : Above the bar code(Font Size : 3)
7 : Below the bar code(Font Size : 4)
8 : Above the bar code(Font Size : 4)

(p9) : quiet zone width(optional) : 0 ~ 20

SLCS Programming Manual

Rev. 1.02

- 19 -

 Quiet zone is added to the front and end of the barcode for safe scanning.

Because of the quiet zone, the barcode seems to be seen drawn in incorrect
position. If p9 is not used, the printer automatically sets parameter to 0.

Quiet zone with = p9  narrow bar width(p4)

„DATA‟ : The various data types can be used in the data field as followings.

1) Fixed text string : „ Text String‟

2) Variable declared in template by SV command : Vnn

3) Counter declared by the SC command : Cn

4) In the Code 128, when send data to printer if codeset selection commands
(>A,>B,>C) will be used codeset can be selected.

By using >A, Codeset will be set Codeset A.
By using >B, Codeset will be set Codeset B.
By using >C, Codeset will be set Codeset C.

If Codeset select command is not used, automatically set to Auto-mode.

 1) , 2) and 3) can be used together

Example

B178,196,0,2,6,100,0,0,‟1234567890‟
B178,196,0,2,6,100,0,0,V00
B178,196,0,2,6,100,0,0,C0

B178,196,1,2,6,100,0,0,‟>A1234567890‟
B178,196,1,2,6,100,0,0,‟>B1234567890‟
B178,196,1,2,6,100,0,0,‟>C1234567890>A5‟

SLCS Programming Manual

Rev. 1.02

- 20 -

Example

SM20,20

B178,196,0,2,6,100,0,0,‟1234567890‟ //Caution:The position is not (178,196) but (78,196)
B150,468,0,4,10,200,0,0,‟1234567890‟

P1

Result

SLCS Programming Manual

Rev. 1.02

- 21 -

2-1-4 B2 (2 Dimensional bar code)

Description

Draw 2D Barcode on the image buffer

Syntax

B2p1,p2,p3……‟DATA‟

Parameters

p1 : Horizontal position (X) [dot]
p2 : Vertical position (Y) [dot]
p3 : 2D barcode selection

p3

2D Barcode

M

MaxiCode

P

PDF417

Q

QR Code

D

Data Matrix

 Following parameters (p4, p5 …. ,Data) are barcodes-specific.

See the following pages for details of each 2D barcodes.

SLCS Programming Manual

Rev. 1.02

- 22 -

Maxicode(When p3 is M)

p1 : Horizontal position (X) [dot]
p2 : Vertical position (Y) [dot]
p3 : M (means „Maxicode‟)
p4 : Mode selection

p4

Rotation

0

Mode0

2

Mode2

3

Mode3

4

Mode4

„DATA‟ : Data format is dependent on „Mode‟

Mode

Data Format

0

2 or 3

„cl,co,pc,lpm‟

4

„lpm‟

cl : Class Code(3 digits)

co : Country Code(3digits)

Mode2 : Numeric Characters

Mode3 : International Characters
pc : Postal Code
lpm : Low priority message(data)

Example

1)Mode 0

B2200,200,M,0,‟999,840,06810,7317,THIS IS A TEST OF MODE 0 STRUCTURED
CARRIER MESSAGE ENCODING. THIS IS AN 84 CHAR MSG‟

2)Mode 2

B2200,200,M,2,‟999,840,06810,7317,THIS IS A TEST OF BIXOLON LABEL PRINTER
SLPD420. MODE 2 ENCODING. THIS IS AN 84 CHAR.‟

3)Mode3

B2200,200,M,3,‟999,056,B1050,7317,THIS IS A TEST OF BIXOLON LABEL PRINTER
SLPD420. MODE 3 ENCODING. THIS IS AN 84 CHAR.‟

4)Mode4

B2200,200,M,4,‟THIS IS A 93 CHARACTER CODE SET A MESSAGE THAT FILLS A
MODE 4, UNAPPENDED, MAXICODE SYMBOL...‟

SLCS Programming Manual

Rev. 1.02

- 23 -

PDF417(When p3 is P)

p1 : Horizontal position (X) [dot]
p2 : Vertical position (Y) [dot]
p3 : P (means „PDF417‟)
p4 : Maximum Row Count : 3 ~ 90
p5 : Maximum Column Count : 1 ~ 30
p6 : Error Correction level

p6

EC Level

EC Codeword

0

0

2

1

1

4

2

2

8

3

3

16

4

4

32

5

5

64

6

6

128

7

7

256

8

8

512

p7 : Data compression method

p7

Data Type

Compression

0

Text

2 Characters per codeword

1

Numeric

2.93 Characters per codeword

2

Binary

1.2 Bytes per codeword

p8 : HRI

0 : Not Printed
1 : Below the barcode

p9 : Barcode origin point

0 : Center of barcode
1 : Upper left corner of barcode(default)

p10 : Module Width : 2 ~ 9
p11 : Bar Height : 4 ~ 99
p12 : Rotation

Value

Rotation

0

No Rotation

1

90 degrees

2

180 degrees

3

270 degrees

„DATA‟ : ASCII data or Binary data.

Example

B2100,750,P,30,5,0,0,1,1,3,10,0,‟ BIXOLON Label Printer SLPD420‟ // The position is (100,750)

SLCS Programming Manual

Rev. 1.02

- 24 -

QR Code(When p3 is Q)

p1 : Horizontal position (X) [dot]
p2 : Vertical position (Y) [dot]
p3 : Q (means „QR Code‟)
p4 : MODEL selection

1 : MODEL1
2 : MODEL2

p5 : ECC Level

p6

Recovery Rate

L

7%

M

15%

Q

25%

H

30%

p6 : Barcode Size : 1~4
p7 : Rotation

Value

Rotation

0

No Rotation

1

90 degrees

2

180 degrees

3

270 degrees

„DATA‟ : ASCII data or Binary data.

Example

B2200,100,Q,2,M,4,0,'ABCDEFGHIJKLMN1234567890' // The position is (200,100)

Data Matrix(When p3 is D)

p1 : Horizontal position (X) [dot]
p2 : Vertical position (Y) [dot]
p3 : D (the ECC 200 data quality format)
p4 : Barcode Size : 1 ~ 4;
P5 : Reverse

N: Normal
R: Reverse(or Inverse) – Reverse Video or Negative image

(P6) : Rotation

Value

Rotation

0

No Rotation

1

90 degrees

2

180 degrees

3

270 degrees

„DATA‟ : ASCII data or Binary data.

Example

B2200,100,D,2,N,'BIXOLON Label Printer' // The position is (200,100)

SLCS Programming Manual

Rev. 1.02

- 25 -

2-1-5 B3 (Special Barcode)

Description

Draw Special Barcode on the image buffer

Syntax

B3p1,p2,p3……‟DATA‟

Parameters

p1 : Horizontal position (X) [dot]
p2 : Vertical position (Y) [dot]
p3 : Special barcode selection

p3

Special Barcode

I

IMB(Intelligent Mail Barcode)

 Following parameters (p4, p5 …. ,Data) are barcodes-specific.

See the following pages for details of each special barcodes.

IMB (p3 = I)

p1 : Horizontal position (X) [dot]
p2 : Vertical position (Y) [dot]
p3 : I (means „IMB‟)
p4 : Rotation

Value

Rotation

0

No Rotation

1

90 degrees

2

180 degrees

3

270 degrees

P5 : HRI :

0 : Not Printed

1 : Below the barcode

„DATA‟ : ASCII data or Binary data.

Example

B3100,100,I,0,1,'0123456709498765432101234567891' // The position is (100,100)

SLCS Programming Manual

Rev. 1.02

- 26 -

2-1-6 BD (Block Draw)

Description

Draw Line, Block, Box & Slope on the image buffer

Syntax

BDp1,p2,p3,p4,p5(,p6)

Parameters

p1 : Horizontal start position (X) [dot]
p2 : Vertical start position (Y) [dot]
p3 : Horizontal end position (X) [dot]
p4 : Vertical end position (Y) [dot]
p5 : Options

p5

Type

Additional p6

O

Line Overwriting

Not necessary

E

Line Exclusive OR

Not necessary

D

Line Delete

Not necessary

S

Slope(a oblique line)

Thickness

B

Box

Thickness

 If p5 is S or B, then additional p6 must follow p5.

SLCS Programming Manual

Rev. 1.02

- 27 -

Example

1) Start and end position

(p1,p2)

(p3,p4)

2) Overwriting mode(when p5 is O)

3) Exclusive OR mode(when p5 is E)

4) Delete block mode(when p5 is D)

SLCS Programming Manual

Rev. 1.02

- 28 -

5) Slope block mode(when p5 is S)

6) Draw box mode(when p5 is B)

(p1,p2)

(p3,p4)

p6 : Thickness

(p1,p2)

(p3,p4)

p6 : Thickness

SLCS Programming Manual

Rev. 1.02

- 29 -

2-1-7 CD (Circle Draw)

Description

Draw Circle on the image buffer

Syntax

CDp1,p2,p3,p4

Parameters

p1 : Horizontal start position (X) [dot]
p2 : Vertical start position (Y) [dot]
p3 : Circle Size Selection

Value

Diameter (mm)

Width  Height(dots)

1

5

40  40

2

7

56  56

3

9

72  72

4

11

88  88

5

13

104  104

6

21

168  168

p4 : Multiplier : 1 ~ 4

Example

CD100,200,2,1

(100,200)

Circle size(diameter is 7mm)

SLCS Programming Manual

Rev. 1.02

- 30 -

2-1-8 CS (Character Set selection)

Description

To select international character set and code table

Syntax

CSp1,p2

Parameters

p1 : International Character Set

p1

Country

0

U.S.A

1

France

2

Germany

3

U.K

4

Denmark I

5

Sweden

6

Italy

7

Spain I

8

Norway

9

Denmark II

10

Japan

11

Spain II

12

Latin America

13

Korea

14

Slovenia/Croatia

15

China

SLCS Programming Manual

Rev. 1.02

- 31 -

p2 : Code Pages

p2

Code Table

Language

0

CP437

U.S.A

1

CP850

Latin1

2

CP 852

Latin2

3

CP 860

Portuguese

4

CP 863

Canadian French

5

CP 865

Nordic

6

WCP 1252

Latin I

7

CP 865 + WCP 1252

European

Combined

8

CP 857

Turkish

9

CP 737

Greek

10

WCP 1250

Latin 2

11

WCP 1253

Greek

12

WCP 1254

Turkish

13

CP 855

Cyrillic

14

CP 862

Hebrew

15

CP 866

Cyrillic

16

WCP 1251

Cyrillic

17

WCP 1255

Hebrew

18

CP 928

Greek

19

CP 864

Arabic

20

CP 775

Baltic

21

WCP1257

Baltic

22

CP858

Latin 1 + Euro

 Default Setting is U.S.A standard (p1=0 and p2=0).

 European Combined Page

Address

Code Page

0x80

Euro Currency

0x81 ~ 0x9f

PC865

0xA0 ~ 0xff

PC1252

SLCS Programming Manual

Rev. 1.02

- 32 -

Country

International Character Set

Hex

23h

24h

40h

5Bh

5Ch 5D

h

5Eh

60h

7Bh

7Ch 7D

h

7E

Dec

35

36

64

91

92

93

94

96

123

123

125

126

U.S.A



＄ @ [ \ ] ^ ` { | } ~

France



＄ à ° ç § ^ ` é ù è ¨

Germany



＄ § Ä

Ö

Ü ^ ` ä ö ü β

U.K.

￡ ＄ @ [ \ ] ^ ` { | } ~ Denmark I



＄ @ Æ

Ø Å ^ ` æ ø å ~ Sweden



¤ É Ä

Ö Å Ü é ä ö å

ü

Italy



＄ @ ° \ é ^ ù à ò è ì

Spain

₧ ＄ @ і Ñ ¿ ^ ` ¨ ñ }

~

Norway



¤ É Æ

Ø Å Ü é æ ø å ü Denmark II



＄ É Æ

Ø Å Ü é æ ø å

ü

Japan



＄ @ [ ￥ ] ^ ` { | } ~

Spain II



＄ á ¡

Ñ ¿ é ` í ñ ó ú Latin America



＄ á ¡

Ñ ¿ é ü í ñ ó

ú

Korea



＄ @ [ \ ] ^ ` { | } ~

Slovenia/Croatia



＄ Ţ Š Đ Ć Ĉ ţ š Ċ ć ĉ

China



¥ @ [ \ ] ^ ` { | } ~

ASCII

Code

0~31 : Control Code
32~127 : Alphanumeric

0 1 2 3 4 5 6 7 8 9 A B C D E F

0
0

Control Characters

1

16

2

32

! " # ＄ % & ' ( ) * + , - .

/

3

48

0 1 2 3 4 5 6 7 8 9 : ; < = >

?

4

64

@ A B C D E F G H I J K L M N

O

5

80

P Q R S T U V W X Y Z [ ] ^ _

`

6

96

a b c d e f g h i j k l m n o

p

7

112

q r s t u v w x y z { | } ~ ⌂

※ Refer to the “Code Pages Manual” for more extension code pages table.

SLCS Programming Manual

Rev. 1.02

- 33 -

2-1-9 P (Print)

Description

Let the printer start printing the content of image buffer

Syntax

Pp1,[p2]

Parameters

p1 : Number of label sets : 1 ~ 65535
p2 : Number of copies of each label : 1 ~ 65535

 The P command cannot be used in a template sequence. If printing command is needed

in template sequence, then use the PV command(See the example of next page).

! Caution

The „P‟ command should be terminated by „CR‟(0x0d). If not, the printer will not start
to print until „CR‟ comes.

SLCS Programming Manual

Rev. 1.02

- 34 -

Example

(1) In case of Using P ( P is used outside of template sequence)

TS’TPL_TST1’ // Start Template Store

SV00,15,N,‟Model Name :‟ // Declare variable V00
T50,100,3,1,1,0,0,N,N,‟Model Name :‟V00 // T command with variable

TE // End Template Store

TR’TPL_TST1” // Recall stored template „TPL_TST1‟
? // Get content of variable used in recalled template
SLPD420 // Content of variable V00
P3,2 // when using P command, It must not be inside
template,
// but be used after recalling the template and entering
the
// contents of all variables.
// After P command, printer starts printing.

(2) In case of Using PV(PV is used inside of template sequence

TS’TPL_TST1’ // Start Template Store

SV00,15,N,‟Model Name :‟ // Declare variable V00
SV01,2,N,‟# of set :‟ // Declare variable V01
SV02,2,N,‟# of copies : „ // Declare variable V02
T50,100,3,1,1,0,0,N,N,‟Model Name :‟V00 // T command with variable

PVV01,V02 // PV command can be used inside the template

TE // End Template Store

TR’TPL_TST1” // Recall stored template „TPL_TST1‟
? // Get content of variable used in recalled template
SLPD420 // Content of variable V00
3 // Content of variable V00
2 // Content of variable V00

// As soon as all contents of variables are entered‟
// printer will starts printing

SLCS Programming Manual

Rev. 1.02

- 35 -

2-2 Media & Buffer Related Commands

1) ST

Select Thermal Direct/Transfer Printing.

2) SM

Set marginal value in label(Image buffer).

3) SF

Set back-feed option.

4) SL

Set label(Image buffer) length.

5) SW

Set label(Image buffer) width.

6) SB

Set buffer mode(Enable or disable Double Buffering).

7) CB

Clear Image Buffer.

SLCS Programming Manual

Rev. 1.02

- 36 -

2-2-1 ST (Set Printing Type)

Description

Select Thermal Direct Printing or Thermal Transfer Printing

Syntax

STp1

Parameters

p1 : Direct Thermal / Thermal Transfer

- d : Direct Thermal

- t : Thermal Transfer

2-2-2 SM (Set Margin)

Description

Set marginal value of the image buffer
This command moves the origin point (0,0) to (p1,p2) and make (p1,p2) become the new

origin.

Syntax

SMp1,p2

Parameters

p1 : Horizontal margin [dots]
p2 : Vertical margin [dots]

 The origin point is upper-left point of the image buffer

SLCS Programming Manual

Rev. 1.02

- 37 -

** When printing orientation is from top to bottom

** When printing orientation is from bottom to top.

(0,0) : Origin

Image Buffer

New Image Buffer

virtual (0,0)

New Origin : (p1,p2)

(p1,p2) : New Origin
virtual (0,0)

Label Feeding
Direction

Label Feeding
Direction

SLCS Programming Manual

Rev. 1.02

- 38 -

2-2-3 SF (Set Back-Feed Option)

Description

Set back-feed option
This command decides whether printer does back-feed action before starting printing.

Syntax

SFp1(,p2)

Parameters

p1 : Enable/Disable

- 0 : Disable back-feed option.

- 1 : Enable back-feed option(Default)
p2 : Back feeding step quantity.

- This parameter is valid when p1 is 1.

- The step quantity defined by user can‟t exceed printer‟s default feeding quantity.

- 0 means printer‟s default feeding quantity.

 This option is useful for the continuous paper or black mark media with perforation line

away from black mark.

 The printer‟s default back feeding step quantity depends on the printer models and

printer modes such as normal, peeler or cutter.

Examples)

SF0 → Disable Printer‟s back-feeding option.
SF1 → Default quantity of Back feed is executed before printing.
SL1,0 → Default quantity of Back feed is executed before printing.
SL1,100 → 100 step‟s Back feed is executed before printing.
SL0,100 → Back feed is disabled and p2(100) is ignored.

SLCS Programming Manual

Rev. 1.02

- 39 -

2-2-4 SL (Set Length)

Description

Set length of label and gap(or Black Mark) and specify media type

Syntax

SLp1,p2(,p3)(,p4)

Parameters

p1 : Label length [dots] : Maximum 2432 dots(12 inch)

 Double buffering feature can be used only when label length(p1) is less
than 1216(2432/2, 6inch) dots.
 If p1 is over 1216 dots, the double buffering feature will be automatically
released.
 So if you don‟t use double buffering feature, you can design maximum
2432 dots(12 inch) size label.

p2 : Gap length or thickness of black line [dots]
p3 : Media Type

p3

Media type

G

Gap

C

Continuous

B

Black Mark

 If this parameter is not used, automatically set to G(Gap type).
 The default value of label length is 6 inch(1216 dots)
 This command sets the length of image buffer and the printer will print

and form feed as much as the length set by this command.

 When using Continuous type media, the label length must be set.
p4 : Offset Length between Black Mark(or Gap) and perforation line [dots]
 This parameter is valid when p3 parameter is used.

Examples)

SL1200,20 → Gap media,Media length:1200dots,Gap length:20dots
SL1200,20,C → Continuuous media,Media length:1200dots,Gap length:20dots
SL1200,20,G → Gap media,Media length:1200dots,Gap length:20dots
SL1200,20,B → Black Mark media,Media length:1200dots,Gap length:20dots
The perforation line is on the black mark.
SL1200,20,B,200 → Black Mark media,Media length:1200dots,Gap length:20dots
The perforation line is 200 dots behind from black mark.

SLCS Programming Manual

Rev. 1.02

- 40 -

 In the Gap Mode, the printer will form feed until meeting the next gap.
 In the Continuous Mode, the printer will form feed as much as label length set by SL.
 In the B/M Mode, the printer will form feed until meeting the next B/M.

Example – p1 & p2(Length)

SL406,20 // Set label length to 406 dots (2 inch, 50mm) and gap length to 20 dots(2.5mm)

p1
(In this example,406)

P2
(In this example,20)

SLCS Programming Manual

Rev. 1.02

- 41 -

Example – p3(Media Type)

1. Gap Type 2. Continuous Type 3. Black Mark Type

Example – p4(Offset Lenght)

Black Mark

Perforation Line

p4 : Offset Length

SLCS Programming Manual

Rev. 1.02

- 42 -

2-2-5 SW (Set Width)

Description

Set label width
Resize the image buffer to match the label size.

Syntax

SWp1

Parameters

p1 : Label width [dots]

 The default value of label width is 4.1 inch( 832 dots) and that is the

maximum printable width.

 SLP-D420 is the center aligned printer and media is positioned in the

center of the head.

Example

SW406 // Set label width to 2 inch(406 dots)

Printer Head, Max 832dots(4 inch)

CENTER OF HEAD

p1

Maximum

Buffer Width

Maximum

Buffer Width

Set by SL

Printing Area

Set by

SL and SW

SLCS Programming Manual

Rev. 1.02

- 43 -

2-2-6 SB (Set Buffer mode)

Description

Set double buffer mode

Syntax

SBp1

Parameters

p1 : Enable „Double Buffering‟ function.

0 : Disable double buffer mode

1 : Enable double buffer mode(Default)

 Double buffering feature enables the printer to construct the image buffer for the next

label while printing the current label.

 Double buffering feature can be used only if the label length set by SL is less than half of

the maximum label length.

2-2-7 CB (Clear Buffer)

Description

Clear image buffer and be ready to make a new label

Syntax

CB

Example

CB // Clear Image Buffer

SLCS Programming Manual

Rev. 1.02

- 44 -

2-3 Printer Setting Commands

1) SS

Set printer speed

2) SD

Set printing density

3) SO

Set printing orientation

4) SP

Set serial port

5) SA

Set Offset

6) TA
Set Tear-off/Cut

SLCS Programming Manual

Rev. 1.02

- 45 -

2-3-1 SS (Set Speed)

Description

Set print speed

Syntax

SSp1

Parameters

p1 : Speed set value

Value

Speed

0

2.5 ips

1

3.0 ips

2

4.0 ips

3

5.0 ips

4

6.0 ips

5

7.0 ips

6

8.0 ips

2-3-2 SD (Set Density)

Description

Set printing density

Syntax

SDp1

Parameters

p1: Density Level

- 0 ~ 20 (0 is the lowest density)

SLCS Programming Manual

Rev. 1.02

- 46 -

2-3-3 SO (Set Orientation)

Description

Set printing direction

Syntax

SOp1

Parameters

p1 : Printing direction

T : Print from top to bottom(default)

B : Print from bottom to top

Example

SOT // Print from top of the image buffer to bottom.
SOB // Print from bottom of the image buffer to top.

1. SOT (Print from Top to Bottom)

2. SOB (Print from Bottom to Top)

Printing Direction

SLCS Programming Manual

Rev. 1.02

- 47 -

2-3-4 SP (Set Port)

Description

Set serial port

Syntax

SPp1,p2,p3,p4

Parameters

p1 : Baud rate

Value

Baud Rate(bps)

0

9,600

1

19,200

2

38,400

3

57,600

4

115,200

p2 : Parity

Value

Parity

O

Odd parity

E

Even parity

N

No parity(Default)

p3 : Number of data bits

Value

Data bits

7

7 bit

8

8 bits (Default)

p4 : Number of stop bits

Value

Stop bits

1

1 bit(Default)

2

2 bits

SLCS Programming Manual

Rev. 1.02

- 48 -

2-3-5 SA (Set Offset)

Description

Save (set) offset length between black marks (or gap) and dotted lines [dots]

Syntax

SAp1

Parameters

p1 : -100~100

 Offset values saved via the use of SA commands are stored permanently on the printer.

(Offset values saved via the cf. SL command are reset after the power is turned off.)

2-3-6 TA (Tear-off/Cutter Position Setting)

Description

This function regulates the label cutting location After printing.
Tear-off position or Cut position can adjust.

Syntax

TAp1

Parameters

p1 : -100~100

 Tear-off/Cutter Position values saved via the use of TA commands are stored permanently

on the printer.

SLCS Programming Manual

Rev. 1.02

- 49 -

2-4 Variable Related Commands

1) SC

Counters which is used in template sequence

2) AC(Auto Counter)

Counters which is used in normal commands sequence
(outside of template sequence)

3) SV

Set variable

4) ?

Get data for counter and variable

5) PV

Print with variables

SLCS Programming Manual

Rev. 1.02

- 50 -

2-4-1 SC (Set Counter)

Description

Define one counter of total 10 counters
Counters must be used in Template sequence and execute consecutive auto-numbering

function.

Syntax

SCp1,p2,p3,p4,‟Prompt‟

Parameters

p1: Identity of Counter : 0 ~ 9

 Total 10 counters, from C0 to C9, are provided.

p2: The size of the field which displays the content of counter : 1 ~ 27
p3: Justification in field(Field size is p2)

Value

Justification

N

No

R

Right

L

Left

C

Center

p4 : Step Value : ±1 ~ ±9

 + or – symbol must precede . Ex) –2 or +3
„Prompt‟: This text string is transmitted to host(PC) by serial interface in order to

give information to host about the declared counter.

 The data field of T(Text) or B(Barcode) commands is used to print the contents of counter.

 SC should be used just in Template sequence. If you want to use counter function in

normal mode(not in Template), use the AC(Auto Counter).

Example

SC0,7,N,+3,‟Please Enter Serial Number‟

SLCS Programming Manual

Rev. 1.02

- 51 -

2-4-2 AC (Auto Counter)

Description

Define one counter of total 10 counters
Counters can be used in normal mode(not in Template) and execute consecutive auto­numbering

Syntax

ACp1,p2,p3,‟Start Value‟

Parameters

p1 : Identity of Counter : 0 ~ 9

 Total 10 counters, from C0 to C9, are provided.

p2 : The size of the field which displays the content of counter : 1 ~ 27
p3 : Step Value : ±1 ~ ±9

 + or – symbol must precede . Ex) –2 or +3

„Start Value‟ : Start value of auto-counting. Just digits can be used in this field

 The Auto-counter defined by AC command can be printed with T and B1 command.
 This function is useful to print serial number or serial barcode without using Template.
 AC can not be used in Template sequence. If you want to use counter function in

Template sequence, use the SC command.

Example

AC0,3,+1,'123' // Please input the start value of counting between „ marks

AC1,7,+1,'1234567'

T100,100,3,1,1,0,0,N,N,C0
B1100,400,0,2,7,100,0,1,12,C1

P3,1

SLCS Programming Manual

Rev. 1.02

- 52 -

2-4-3 SV (Set Variable)

Description

Define variables for the text or barcode „data‟ fields

Syntax

SVp1,p2,p3,‟Prompt‟

Parameters

p1 : Identity of Variables : 00 ~ 99
p2 : Maximum number of characters : 1 ~ 99
p3 : Justification in field(Field size is p2)

Value

Justification

N

No

R

Right

L

Left

C

Center

„Prompt‟ : This ASCII text field is used to ask a value to be entered for the variable(p1)
and is

transmitted to the host by serial interface.

 The data field of T(Text) or B(Barcode) commands is used to print the contents of variable.
 Variable is entered to data field like V00 or V01.

Example

SV01,20,N,‟Please Enter Product Code :‟

SLCS Programming Manual

Rev. 1.02

- 53 -

2-4-4 ? (Get Variables)

Description

Use this command to get the content of variables or counters

Syntax

?

Content of variable

 Data must be entered in ascending order

Example

TS‟Template1‟ // Template Store Start

SV00,20,N‟Enter Company Name : ‟ // Declare(Set) variable V00
SV01,15,N‟Enter Product Code :‟ // Declare(Set) variable V01

T50,30,3,1,1,0,0,N,N,V00 // Use T command to print V00
T50,150,3,1,1,0,0,N,N,‟Code : ‟V01 // Use T command to print V01
TE // Template Store End

TR‟Template1‟ // Recall Template1
? // Start to get data for variables
SEM // data for V00
D420 // data for V01

P1 // Start Printing when the P command comes

Result

SEM
Code : D420

SLCS Programming Manual

Rev. 1.02

- 54 -

2-4-5 PV (Print with Variables)

Description

This command is used in template sequence.
The parameters are given by variables.

Syntax

PVp1,[p2]

Parameters

p1 : Number of label sets : 1 ~ 65535
p2 : Number of copies of each label : 1 ~ 65535

Example

TS‟Template1‟ // Template Store Start

SV00,20,N,‟Please Input the Name :‟ // Declare(Set) variable V00
SV01,5,N,‟Input Number of label sets :‟ // Declare(Set) variable V01
SV02,5,N,‟Input Number of label copies :‟ // Declare(Set) variable V02

T50,30,3,1,1,0,0,N,N,V00 // Write V00 to image buffer

PVV01,V02 // Print V00, V02 copies, V01 sets
TE // Template Store End

TR‟Template1‟ // Recall Template1

? // Start to get data for variables
This is PV Test // data for V00
2 // data for V01
1 // data for V02

*** Start Printing as soon as data for all variables(and counters) are entered. ***

SLCS Programming Manual

Rev. 1.02

- 55 -

2-5 Template Related Commands

Template(a certain format of label, sequence of SLCS commands) related commands

1) TS

Indicate start of template sequence store.

2) TE

Indicate end of template sequence store.

3) TR

Recall and reuse stored template.

4) TD

Delete stored template.

5) TI

Print the list of all templates stored in memory.

SLCS Programming Manual

Rev. 1.02

- 56 -

2-5-1 TS (Template store Start)

Description

Start template sequence storing.
All the contents following „TS‟ are stored in memory until meeting „TE‟ Command.

Syntax

TS‟Template name’

Parameters

„Template name‟: This name will be used when „Recall‟ the stored template.

 The name is allowed to be up to 10 characters long.
 The „Template name‟ is Case-Sensitive.

 TI command shows the list of currently stored Templates.

2-5-2 TE (Template store End)

Description

End template sequence storing

Syntax

TE

 When storing is finished, the printer sends „!‟ to the host to prompt end of storing.

Example

TS‟Template1‟ // Start template storing
……

TE // End template storing

SLCS Programming Manual

Rev. 1.02

- 57 -

2-5-3 TR (Template Recall)

Description

Recall the stored template from memory to make a label and print that

Syntax

TR’Template name’

Parameters

„Template name‟ : Indicate the template to be recalled.

 The name is allowed to be up to 10 characters long.
 The „Template name‟ is Case-Sensitive.

Example

TR‟Template1‟ // Recall „Template1‟

 If recalled Template does not include any variable or counter, just „P‟ command is enough

to start printing.

 If recalled Template includes variables or counters but not „PV‟(Print with Variables), use

„?‟ command to get data for variables and counters and finally „P‟ command is necessary

to start printing.

 If recalled Template includes PV commands, printing will start as soon as all data for

variables and counters are entered.

SLCS Programming Manual

Rev. 1.02

- 58 -

2-5-4 TD (Template Delete)

Description

Delete stored template from memory

Syntax

TD’Template name’

Parameters

„Template name‟ : Indicate the template to be deleted.

 The name is allowed to be up to 10 characters long.
 The „Template name‟ is Case Sensitive.
 By using *, all templates will be deleted from memory.

Example

TD‟Template1‟ // Delete „Template1‟
TD* // Delete all currently stored templates

2-5-5 TI (Template Information)

Description

Print list of currently stored templates and available memory space

Syntax

TI

Example

TI

Result

Templates Information
========================

1. Template1

2. Template2
Available template memory : 53Kbyte

SLCS Programming Manual

Rev. 1.02

- 59 -

2-6 Image Related Commands

These commands provide functions to download and print graphic data.
PCX and BMP format file are supported and bitmap image data can be printed directly.

1) IS

Download PCX format image data to NV(Non Volatile) area of memory.

2) IR

Recall and print downloaded image data.

3) ID

Delete image data in NV memory.

4) II

Print all images stored in memory.

5) LD

Draw the bitmap image data directly on specific position on image buffer.

6) LC

Draw compression bitmap image data on specific position of image buffer.

7) BMP

Draw BMP format image file directly on specific position on image buffer.

SLCS Programming Manual

Rev. 1.02

- 60 -

2-6-1 IS (Image Store)

Description

Download PCX format Image file into the Printer Memory

Syntax

ISp1,‟Image name‟DATA OF *.PCX

Parameters

p1 : The size of image file in unit of byte.

„Image name‟ : This is the name that will be used when recalling the stored image data.

 The name is allowed to be up to 10 characters long.
 The name is case sensitive.

DATA OF *.PCX : Binary data string of PCX file.

2-6-2 IR (Image Recall)

Description

Recall the stored image from memory and draw that on the image buffer

Syntax

IRp1,p2,‟Image name‟

Parameters

p1 : Horizontal position (X) [dot]
p2 : Vertical position (Y) [dot]

„Image name‟ : Indicate the image data to be recalled.

 Variable can be used in this field.
 The name is allowed to be up to 10 characters long.
 This name is Case Sensitive.

Example

IR30,100,‟Image1‟ // Recall „Image1‟
IR30,100,V01 // Variable can be used in name field

SLCS Programming Manual

Rev. 1.02

- 61 -

2-6-3 ID (Image Delete)

Description

Delete stored image from memory

Syntax

ID’Image name’

Parameters

„Image name‟ : Indicate the Image in memory to be deleted.

 The name is allowed to be up to 10 characters long.
 This name is Case Sensitive.
 By using *, all images in memory will be deleted.

Example

ID‟Image1‟ // Delete „Image1‟
ID* // Delete all currently stored images

2-6-4 II (Image Information)

Description

Print list of currently stored images in memory and available memory space

Syntax

II

Example

II

Result

Image Information
=====================

1. Image1

2. Image2
Available Images memory : 5.3Kbyte

SLCS Programming Manual

Rev. 1.02

- 62 -

2-6-5 LD

Draw bitmap image data on specific position of image buffer

Syntax

LDxL xH yL yH dhL dhH dvL dvH d1~dk

Parameters

xL : Low byte of horizontal start position (X) [dot]
xH : High byte of horizontal start position (X) [dot]
→ Start position in x direction = xH * 256 + xL

yL : Low byte of vertical start position (Y) [dot]
yL : High byte of vertical start position (Y) [dot]
→ Start position in y direction = yH * 256 + yL

dhL : Low byte of the number of bytes in x-direction.
dhH : High byte of the number of bytes in x-direction.
→ Number of data in x direction = dhH * 256 + dhL

dvL : Low byte of the number of lines.
dvH : High byte of the number of lines.
→ Number of data in y direction = dvH * 256 + dvL

d1~dk : bitmap image data.
→ k = (dhH*256 + dhL) * (dvH*256 + dvL)

! CAUTION

There are no commas(,) and no space between each parameters.

SLCS Programming Manual

Rev. 1.02

- 63 -

Example

LD 0x11 0x02 0x40 0x02 0x08 0x00 0x20 0x00 0xFF ~ 0xFF

① ② ③ ④ ⑤

① x position : 0x02 * 0x100(256) + 0x11 = 0x211(529)
② y position : 0x02 * 0x100(256) + 0x40 = 0x240(576)
③ horizontal data number : 0x00 * 0x100(256) + 0x08 = 0x08(8)
④ vertical data number : 0x00 * 0x100(256) + 0x20 = 0x20(32)
⑤ bitmap data : total number = 8 * 32 = 256

(①, ②)

③

④

SLCS Programming Manual

Rev. 1.02

- 64 -

2-6-6 LC

Draw compression bitmap image data on specific position of image buffer

Syntax

LCp1p2xL xH yL yH dhL dhH dvL dvH d1~dk

Parameters

p1: Compression type
R: RLE
p2: Color
0x00: black
0x01: Color(red or blue)

xL : Low byte of horizontal start position (X) [dot]

xH : High byte of horizontal start position (X) [dot]
→ Start position in x direction = xH * 256 + xL

yL : Low byte of vertical start position (Y) [dot]
yH : High byte of vertical start position (Y) [dot]
→ Start position in y direction = yH * 256 + yL

dhL : Low byte of the number of bytes in x-direction.
dhH : High byte of the number of bytes in x-direction.
→ Number of data in x direction = dhH * 256 + dhL

dvL : Low byte of the number of lines.
dvH : High byte of the number of lines.
→ Number of data in y direction = dvH * 256 + dvL

d1~dk : Compression bitmap image data.
→ k = (dhH*256 + dhL) * (dvH*256 + dvL)

! CAUTION

There are no commas(,) and no space between each parameters.

SLCS Programming Manual

Rev. 1.02

- 65 -

Example

LC R 0x00 0x11 0x02 0x40 0x02 0x08 0x00 0x20 0x00 0xFF ~ 0xFF
○1 ○2 ○3 ○4 ○5 ○6 ○7

①Compression type : R =RLE
②Color : 0x00 = Black

③x position : 0x02 * 0x100(256) + 0x11 = 0x211(529)
④y position : 0x02 * 0x100(256) + 0x40 = 0x240(576)
⑤horizontal data number : 0x00 * 0x100(256) + 0x08 = 0x08(8)
○6vertical data number : 0x00 * 0x100(256) + 0x20 = 0x20(32)
○7bitmap data : total number = 8 * 32 = 256

RLE compression
This is the algorithm to compress the continuous data.
The compression is applied to 0x00 & 0xff data but not the others.
0xff 0x04 data is created if 0xff is repeated four times like 0x00 0x00 0x00 0x00.
In the same way, 0x00 0x04 is created by four times repeats of 0x00 such as 0x00 0x00 0x00 0x00.
Here is the example of compression.

Example) 0x78 0x78 0xff 0xff 0xff 0xff 0xff 0x22 0x00 0x00 0x00 0x00
0x78 0x78 0xff 0x05 0x22 0x00 0x04

(③, ④)

⑤

○

6

SLCS Programming Manual

Rev. 1.02

- 66 -

2-6-7 BMP

Send BMP format file directly to printer.

Just white/black BMP file is supported

Syntax
BMPp1,p2↓
Data string of *.bmp

Parameters

p1 : Horizontal position (X) [dot]

p2 : Vertical position (Y) [dot]

1. ↓ means „CR(+LF)‟

2. There is comma(,) between p1 and p2.

3. After p2(Before sending BMP data string) „CR(+LF)‟ must follow.

Example

In dos mode,
COPY bmp.txt+image2.bmp+P.txt LPT1 /b

BMP200,200 ↓

Bmp.txt

P1 ↓

P.txt

SLCS Programming Manual

Rev. 1.02

- 67 -

2-7 Downloadable font Related Commands

Download fonts into the printer memory. Users can download special size or
special design of ASCII font and use this font with T command.

1) DT

Download True Type Font into Printer Memory

2) DD

Delete downloaded fonts from memory

3) DI

Print all downloaded fonts in memory and available memory space

SLCS Programming Manual

Rev. 1.02

- 68 -

2-7-1 DT (Download True Type Font)

Description

Download windows system font into printer memory

Syntax

DTp1,p2,‟Font Name‟ a1b1(DATA1)a2b2(DATA2)…anbn(DATAn)

Parameters

p1 : Total number of characters to be downloaded: 0~255

p2 : Font Height: 0~255

Font name : A ~ Z

an : Character position in ASCII Table(0~255)

bn : Font width(dots)

(DATAn) : Character Bitmap Data

Total bytes of bitmap data : p2 × (bn+7)/8 bytes

Example

44 44 2a 0d 0a 44 54 60 14 27 41 27 DD*..DT..‟A‟

20 0b ……

21 0c ……

……

p1 p2Font name

a1

b1

DATA1 : p2×(b

1

+7)/8 bytes

b2

DATA2 : p2×(b

2

+7)/8 bytes

a2

p2 =
12

bn =8bits(1Byte)

Number of DATAn = 12 × (8+7)/8 = 12 Bytes

SLCS Programming Manual

Rev. 1.02

- 69 -

2-7-2 DD (Downloaded font Delete)

Description

Delete downloaded font from memory

Syntax

DD’font name’

Parameters

„font name‟ : Indicate the Image in memory to be deleted.(A~Z)

 This name is Case Sensitive.
 By using *, all images in memory will be deleted.

 You can show the downloaded font list by DI command.

Example

DD‟A‟ // Delete downloaded font A
DD* // Delete all downloaded fonts in memory

SLCS Programming Manual

Rev. 1.02

- 70 -

2-7-3 DI (Downloaded font Information)

Description

Print list of downloaded font

Syntax

DI

Example

DI

Result

Download Font Information
=============================
Name w h c Size
=============================
C 16 25 128 6400
G 12 24 224 10752

Free Memory 179419
=============================

 w : font width, h : font height, c: total number of characters

SLCS Programming Manual

Rev. 1.02

- 71 -

2-8 The Others

Commands not included in 1 to 7 categories.

1) @

Printer initialization.

2) PI

Print information of printer configuration.

3) CUT

Enable/Disable Cutting Action

4) ^cp

Check printer status and report 2bytes status data to host.

5) ^cu

Check printer status and report 1byte status data to host.

6) ^PI

Send various printer information to host.

7) ^MBZ

Power save mode setting.

8) ^MBP

Send power save mode setting to host.

SLCS Programming Manual

Rev. 1.02

- 72 -

2-8-1 @ (Initialize Printer)

Description

Initialize the printer

Syntax

@

2-8-2 PI (Printer Information)

Description

Print current printer setting

Syntax

PI

SLCS Programming Manual

Rev. 1.02

- 73 -

2-8-3 CUT (Auto-cutter Enable/Disable)

Description

Enable or Disable Auto-cut action after printing by „P‟ command

Syntax

CUTp1(,p2)

Parameters

p1 : Cutting Action Enable/Disable

y : Enable cutter to act after printing is finished.
n : Disable cutter.

p2 : Cutting Period
 Cutting Period means the number of pages between two cuttings.

 This command is not the cutting command itself but cutting enable/disable command.



Cutting is executed immediately after printing is finished by P command if the cutter

option is enabled by this CUT command.

 Last page is always cut.

Example – p1(Cutter Enable/Disable)

Cutting is executed after Printing is finished

Cutting is not executed after Printing is

finished

T20…
B130…
BD…
…

CUTy

P1

T20…
B130…
BD…
…

CUTn

P1

Example – p2(Cutting Period)

CUTy // Cut every page
CUTy,1 // Cut every page
CUTy,2 // Cut every 2 pages
CUTy,4 // Cut every 4 pages

SLCS Programming Manual

Rev. 1.02

- 74 -

2-8-4 ^cp (Check Printer Status and Report 2 bytes)

Description

Check printer status and report 2bytes status data to host

Syntax

^cp

Return Value

1. Format
<1

st

Byte> <2nd Byte>

2. Table

Return Values

Description

Hex

Byte

bit

1st Byte

7

Paper Empty

0x80

6

Cover Open

0x40

5

Cutter jammed

0x20

4

Thermal Head(TPH) overheat.

0x10

3

Gap Detection Error(Auto-sensing failure)

0x08

2

Ribbon End Error

0x04

1

Not assigned

0x02

0

Not assigned

0x01

2nd

Byte

7

On building label to be printed in image
buffer.

0x80

6

On printing label in image buffer

0x40

5

Issued label is paused in peeler unit.

0x20

4

Not assigned

0x10

3

Not assigned

0x08

2

Not assigned

0x04

1

Not assigned

0x02

0

Not assigned

0x01

3. Examples

When Return

Values are

Printer Status is

1st Byte

2nd Byte

0x00

0x00

No Error. The printer is ready to build and print label.

0x80

0x00

No paper is installed in printer.

0x80

0x40

Paper roll out while printing label. When new paper roll is
loaded, the printer will re-issue the last label.

0x60

0x40

While printing, cutter is jammed and cover is opened (by
user).

SLCS Programming Manual

Rev. 1.02

- 75 -

2-8-5 ^cu (Check Printer Status and Report 1 byte)

Description

Check printer status and report 1 byte status data to host

Syntax

^cu

Return Value

1. Format
<1

st

Byte>

2. Table

Return Values

Description

Hex

Byte

bit

1st Byte

7

Paper Empty

0x80

6

Cover Open

0x40

5

Cutter jammed

0x20

4

Thermal Head(TPH) overheat.

0x10

3

Gap Detection Error(Auto-sensing failure)

0x08

2

Ribbon End

0x04

1

Not assigned

0x02

0

Not assigned

0x01

SLCS Programming Manual

Rev. 1.02

- 76 -

2-8-6 ^PI (Send Printer information to host)

Description

Send various printer information such as model name, firmware version, statistics data or

so to host

Syntax

^PIp1(,p2)(,p3)

Parameters

p1 : items to be reported.

0 : Model Name
1 : Model Type : Disabled
2 : F/W Version

3: None

4 : Mechanical conditions of printer

p2

Item

Unit

0

TPH temperature

℃

1

Printing density (density)

-

2

Tear-off/cutter position

dot

Return Value Format

Items

Return Format

Example

Model Name

Character String + 0x0d + 0x0a

“SRP-770” + 0x0d + 0x0a

Model Type

Disabled F/W Version

Character String + 0x0d + 0x0a

“1.23” + 0x0d + 0x0a

TPH temperature

Character String + 0x0d + 0x0a

“85” + 0x0d + 0x0a

Printing density (density)

Character String + 0x0d + 0x0a

“17” + 0x0d + 0x0a

Paper Width

Character String + 0x0d + 0x0a

“832” + 0x0d + 0x0a

Paper Length

Character String + 0x0d + 0x0a

“1200” + 0x0d + 0x0a

Gap Length

Character String + 0x0d + 0x0a

“24” + 0x0d + 0x0a

Paper Horizontal Margin

Character String + 0x0d + 0x0a

“10” + 0x0d + 0x0a

Paper vertical Margin

Character String + 0x0d + 0x0a

“12” + 0x0d + 0x0a

Tear-off/cutter position

Character String + 0x0d + 0x0a

“+80” + 0x0d + 0x0a

SLCS Programming Manual

Rev. 1.02

- 77 -

2-8-7 ^MBZ (Power Save mode setting)

Description

Power save mode setting

Syntax

^MBZp1,p2

Parameters

p1 : Power save mode enable/disable

0: Disable
1: Enable
p2 : Power save mode penetration timely set (unit: seconds)
0 < p2 < 256
p2 sec.

Example

1) Power save mode enable, penetration timely is 30seconds.
^MBZ1,30

2) Power save mode disable

^MBZ0,0

2-8-8 ^MBP (Send power Save mode information to host)

Description

Send power save mode setting to host

Syntax

^MBP

Parameters

None

Return Value Format

“ Enable/disable” + “ penetration timely” + 0x0d + 0x0a

Example

0x01 0x14 0x0d 0x0a // Power save mode enable (0x01)

// penetration timely 20seconds (0x14)

SLCS Programming Manual

Rev. 1.02

- 78 -

3. Programming Example

3-1 Example) T_resident

SS3 // Set Speed to 4 ips
SD20 // Set Density level to 20
SW800 // Set Label Width 800
SOT // Set Printing Orientation from Top to Bottom
T26,20,0,1,1,0,0,N,N,‟Font - 6 pt‟
T26,49,1,1,1,0,0,N,N,‟Font - 8 pt‟

T26,81,2,1,1,0,0,N,N,‟Font - 10 pt‟
T26,117,3,1,1,0,0,N,N,‟Font - 12 pt‟
T26,156,4,1,1,0,0,R,N,‟Font - 15 pt‟
T26,200,5,1,1,0,0,N,N,‟Font - 20 pt‟
T26,252,6,1,1,0,0,N,N,‟Font - 30 pt‟

P1

Result

Font – 6 pt

Font – 8 pt

Font – 10 pt

Font – 12 pt

Font – 15 pt

Font – 20 pt

Font – 30 pt

SLCS Programming Manual

Rev. 1.02

- 79 -

3-2 Example) T_Rotate4

SS3
SW832

T300,500,4,1,1,0,0,N,N,‟ABCDEFG‟
T300,500,4,1,1,0,1,N,N,‟ABCDEFG‟
T300,500,4,1,1,0,2,N,N,‟ABCDEFG‟
T300,500,4,1,1,0,3,N,N,‟ABCDEFG‟

P1

Result

SLCS Programming Manual

Rev. 1.02

- 80 -

3-3 Example) V_resident

SS3 // Set speed to 4 ips
SD20 // Set density to 20
SW800 // Set label width to 800
SOT // Set printing direction to from top to bottom

V50,100,U,25,25,+1,N,N,N,0,L,0,'Vector Font Test'
V50,200,U,35,35,-1,N,N,N,0,L,0,'Vector Font Test'
V50,300,U,35,35,+1,B,R,I,0,L,0,'Vector Font Test '
V50,400,U,45,25,+1,N,N,N,0,L,0,'Vector Font Test'
V50,500,U,25,45,+1,N,N,N,0,L,0,'Vector Font Test'
V50,700,U,65,65,+1,N,N,N,0,L,0,'ABCDEFGHIJKLMNO'
V50,900,U,65,65,+1,N,N,N,0,L,0,'abcdefghijklmno'

P1

Result

SLCS Programming Manual

Rev. 1.02

- 81 -

3-4 Example) V_Rotate4

SS3
SW832
V400,500,U,45,40,+1,N,N,N,0,L,0,'VECTOR FONT'
V400,500,U,45,40,+1,N,N,N,1,L,0,'VECTOR FONT'
V400,500,U,45,40,+1,N,N,N,2,L,0,'VECTOR FONT'
V400,500,U,45,40,+1,N,N,N,3,L,0,'VECTOR FONT'
P1

Result

SLCS Programming Manual

Rev. 1.02

- 82 -

3-5 Example) Code39

SM10,0

B178,196,0,2,6,100,0,0‟1234567890‟ // Caution : The position is not (178,196)
but (78,196).

B150,468,0,4,10,200,0,0‟1234567890‟
P1

Result

SLCS Programming Manual

Rev. 1.02

- 83 -

3-6 Example) BD1

SS3 // Set Speed to 4 ips
SD20 // Set Density level to 20
SW800 // Set Label Width to 800

BD50,50,750,500,B,20

T100,150,5,1,1,0,0,N,N,‟Normal Mode‟
T100,300,5,1,1,0,0,R,N,‟Reverse Mode‟

SOT
P1

Result

Normal Mode

Reverse Mode

SLCS Programming Manual

Rev. 1.02

- 84 -

3-7 Example) BD3

SS3 // Set Printing Speed to 4 ips
SD20 // Set Printing Density level to 20
SW800 // Set Label Width to 800

BD50,100,400,150,O // Draw a block in Overwriting Mode
BD50,200,400,250,O
BD50,300,400,350,O
BD100,50,150,400,E // Draw a block in Exclusive OR mode
BD200,50,250,400,E
BD300,50,350,400,E
BD500,200,700,400,O
BD510,210,670,370,D // Draw a block in Delete mode, namely Erase block
area
BD100,600,350,1000,O

T50,700,5,1,1,0,0,N,N,‟NORMAL‟ // Write Text data on image buffer
T50,800,5,1,1,0,0,N,N,‟NORMAL‟

BD110,780,340,900,E
T500,700,5,1,1,0,0,n,N,‟TEST‟
BD480,680,700,800,E

SOT // Set Printing Orientation from Top to Bottom
P1 // Start Printing

SLCS Programming Manual

Rev. 1.02

- 85 -

Result

NORMAL

NORMAL

TE ST

SLCS Programming Manual

Rev. 1.02

- 86 -

3-8 Example) BD4

SW800
SM10,0

BD100,300,550,330,O // Overwrite mode
BD200,200,250,430,O // Overwrite mode
BD400,200,450,430,E // Exclusive OR mode

P1

Result

SLCS Programming Manual

Rev. 1.02

- 87 -

3-9 Example) BD5

CB
SW800
SM10,0
BD100,300,300,500,O
BD400,300,700,500,B,30 // Box mode, additional parameter follows
P1

Result

SLCS Programming Manual

Rev. 1.02

- 88 -

3-10 Example) Slope

CB
SS3
SD20
SW8000

BD100,300,300,800,S,100 // Slope mode, additional parameter follows
BD600,300,400,800,S,100

P1

Result

SLCS Programming Manual

Rev. 1.02

- 89 -

3-11 Example) SW&SL

CB
SS3
SD20

SW800 // Set Label Width to 800
SL300,10,C // Continuous type

BD0,0,800,300,B,10
T30,40,4,1,1,0,0,N,N,'SW=800, SL=300, Continuous'
P1

SW600
SL500,10,C

BD0,0,600,500,B,10
T30,40,4,1,1,0,0,N,N,'SW=600, SL=500'
T30,100,4,1,1,0,0,N,N,'Continuous'
P1

SW400
SL800,10,C

BD0,0,400,800,B,10
T30,40,4,1,1,0,0,N,N,'SW=400'
T30,90,4,1,1,0,0,N,N,'SL=800'
T30,140,4,1,1,0,0,N,N,'Continuous'
P1

SLCS Programming Manual

Rev. 1.02

- 90 -

Result

SW = 800, SL=300, Continuous

SW = 600, SL=500,

Continuous

SW= 400,

SL = 800,

Continuous

SLCS Programming Manual

Rev. 1.02

- 91 -

3-12 Example) TEST00_TS

TD‟Test00‟ // Template Delete
TS‟ Test00‟ // Start Template Store

SV00,15,N,‟Manufacturer :‟ // Declare variable V00, field size:15, No
justification
SV01,15,R,‟Model Name :‟ // Declare variable V01, field size:15, Right
justification

T50,100,3,1,1,0,0,N,N,‟Manufacturer :‟V00 // Print variable V00 with some text string
T50,150,3,1,1,0,0,N,N,‟Model Name :‟V01 // Print variable V01 with some text string

T50,300,3,1,1,0,0,N,N,V00 // Print variable V00 only
T50,350,3,1,1,0,0,N,N,V01 // Print variable V01 only

TE // End Template Store

TI // Print and show all templates in memory

Result

Templates Information
===================

1. Test 1

2. Test0
Available template memory : 5.3Kbyte

Stored in past time

Stored in this time

SLCS Programming Manual

Rev. 1.02

- 92 -

3-13 Example) TEST00_TR

TR‟Test00‟ // Recall Stored template „Test00‟

? // To get contents for variables used in „Test00‟

SEM // Content for V00
SLPD420 // Content for V01

P1 // Print

Result

Manufacturer : SEM
Model Name : SLPD420
SEM

SLPD420

Right Justification

Right Justification

No Justification

No Justification

SLCS Programming Manual

Rev. 1.02

- 93 -

3-14 Example) TEST04_TS

TS‟Test04‟ // Start Template Store

CB // Clear Image Buffer
SS3 // Set Speed to 4 ips
SD20 // Set Density level 20
SW800 // Set Label Width to 800
SOT // Set Printing Orientation from Top to Bottom(Default)

SV00,15,L,‟prompt‟ // Declare variable V00, field size:15, Left justification
SV01,15,R,‟prompt‟ // Declare variable V01, field size:15, Right justification
SV02,15,C,‟prompt‟ // Declare variable V02, field size:15, Center

justification

SV03,15,N,‟prompt‟ // Declare variable V03, field size:15, No justification
SV04,15,L,‟prompt‟ // Declare variable V04, field size:15, Left justification
SV05,15,R,‟prompt‟ // Declare variable V05, field size:15, Right justification
SV06,15,C,‟prompt‟ // Declare variable V06, field size:15, Center

justification
SV07,15,N,‟prompt‟ // Declare variable V07, field size:15, No justification

T26,50,4,1,1,0,0,R,N,V00 // Print variable only
T26,100,4,1,1,0,0,R,N,V01
T26,150,4,1,1,0,0,R,N,V02
T26,200,4,1,1,0,0,R,N,V03

T26,250,4,1,1,0,0,R,N,‟SLPD420 :‟V04 // Print variable with fixed text data
T26,300,4,1,1,0,0,R,N,‟ SLPD420 :‟V05
T26,350,4,1,1,0,0,R,N,‟ SLPD420 :‟V06
T26,400,4,1,1,0,0,R,N,‟ SLPD420 :‟V07

TE // End Template Store

SLCS Programming Manual

Rev. 1.02

- 94 -

3-15 Example) TEST04_TR

TR‟Test04‟ // Recall Template

? // Start Get values for variables
A // data for variable V00
B // data for variable V00
C .
D .
E .
F .
G
H // data for variable V07

P1 // Start Printing

3-16 Example) IR1

IR130,400,‟BIXOLON‟ // Recall stored image data
P1 // Printing

!!! Use the PCXDown utility when you download the pcx image file to printer
memory. Refer to IS command.

Result

A

B

C

D

SLPD420 : E

SLPD420 : F

SLPD420 : G

SLPD420 : H

SLCS Programming Manual

Rev. 1.02

- 95 -

3-17 Example) TEST10_TS

TS‟Test10‟ // Start Template Store

CB // Clear Image Buffer
SS3 // Set Speed to 5 ips
SD20 // Set Density to 20
SW800 // Set Label Width to 800
SOT // Set Printing Orientation from Top to bottom

SV00,15,C,‟prompt‟ // Declare Variable 00
SV01,15,N,‟prompt‟ // Declare Variable 01
SV02,10,N,‟prompt‟ // Declare Variable 02

T130,250,5,1,1,0,0,R,N,V00 // Print Content of V00
T250,600,5,1,1,0,0,N,N,V01 // Print Content of V01
IR130,400,V02 // Use V02 as Image Name

TE // End Template Store

3-18 Example) TEST10_TR

(File location : CD\Testfile\Template\Test10\TEST10_TR.txt)

TR‟Test10‟ // Recall Template

? // Start Get data for variables

BIXOLON // data for V00
SLPD420 // data for V01
BIXOLON // data for V02(Image Name)

P1 // Start Printing

BIXOLON

SLPD420

SLCS Programming Manual

Rev. 1.02

- 96 -

3-19 Example) TEST11_TS

TS‟Test11‟ // Start Template Store

CB // Clear Image Buffer
SS2 // Set Printing Speed to 4 ips
SD20 // Set Density to 20
SW800 // Set Label Width to 800
SOT // Set Printing Orientation from Top to Bottom
SC0,4,L,+1,‟COUNTER1‟ // Declare Counter 0, Field=4, Step:+1,Left
Justi.
SC1,4,N,-1,‟COUNTER2‟ // Declare Counter 1, Field=4, Step: -1,No
Justi.
T50,50,4,1,1,0,0,N,N,‟Serial Number : „C0 // Print Counter 0
T50,150,4,1,1,0,0,R,N,‟Serial Number : „C1 // Print Counter 1

TE // End of Template Store

3-20 Example) TEST11_TR

TR‟Test11‟ // Recall Template

? // Start Get values for variables
0001 // data for Counter 0

9999 // data for Counter 1
P3,1

?

9999
0001
P3,1

Serial Number : 0001

Serial Number : 9999

Serial Number : 0002

Serial Number : 9998

Serial Number : 0003

Serial Number : 9997

Serial Number : 9999

Serial Number : 0001

Serial Number : 0000

Serial Number : 0000

Serial Number : 0001

Serial Number : 9999

SLCS Programming Manual

Rev. 1.02

- 97 -

3-21 Example) SLCS_BIXOLON

SM10,21
SS3

SD20
SW832
SOT

CS0,0

BD18,14,798,164,O
T400,62,4,2,2,0,0,R,B,'BIXOLON'
T65,98,3,1,1,0,0,R,B,'BIXOLON Label'
T20,276,3,1,1,1,0,N,N,' BIXOLON'
T20,306,3,1,1,1,0,N,N,' Yeongtong Dong'
T20,336,3,1,1,1,0,N,N,' Sowon City,South Korea'
T22,218,4,1,1,0,0,N,B,'SHIP TO:'
BD18,410,784,415,O
BD553,197,558,413,O
B169,458,0,4,8,137,0,0,0,'*1234567890*'
T26,421,1,1,1,0,0,N,N,'POSTAL CODE:'
BD18,616,784,621,O
BD20,781,786,786,O
T503,798,1,1,1,0,0,N,N,'DESTINATION:'
T42,841,5,1,1,0,0,N,B,'30 Kg'
BD18,928,784,933,O
T25,798,1,1,1,0,0,N,N,'WEIGHT:'
T259,798,1,1,1,0,0,N,N,'DELIVERY NO:'
T23,630,1,1,1,0,0,N,N,'AWB:'
BD241,783,246,932,O
BD486,784,491,933,O
T274,841,5,1,1,0,0,N,B,'425518'
T104,627,3,1,1,0,0,N,N,'8741493121'
T565,841,5,1,1,0,0,N,B,'ICN'
B1127,672,4,4,8,90,0,0,0,'8741493121'
B2560,180,M,0,'999,840,06810,7317,THIS IS A TEST OF MODE 0 STRUCTURED CARRIER
MESSAGE ENCODING. THIS IS AN 84 CHAR MSG'
B280,960,P,30,10,0,0,0,1,3,14,0,'BIXOLON Label Printer SLPD420, This is Test Printing.'
P1

SLCS Programming Manual

Rev. 1.02

- 98 -

Result