Bitatek Cyclops 2 User Manual

Cyclops 2 User Quick Guide

Scan LED

Barcode Scanning Indication:
Green light ON: Successful Reading
Red light ON: Decoding Failed
Blinking Orange: System Firmware is Updating
Orange: System Firmware Update Completed

Battery LED

Battery Status
Green light ON: Charging Completed
Green light blinking: Battery Power Low
Red light ON: Battery Charging in Process
Red light blinking: Charging Failed

Bluetooth LED

Bluetooth Connection Indication:
Blue light fast blinking: Waiting for Paring Connection
Blue light blinking slowly: Pairing Successful and Data
Transmission in Process

SCAN (Power)
key

Press SCAN key for 3-second to power ON
CYCLOPS 2

FUNCTION key

Function of this key differs depending on various
modes CYCLOPS 2 been configured into

Charging
Contacts

For connections of charging tools
USB Port

For Host Device USB Port Connection

Reset Button

Press this button to reset CYCLOPS 2 into Factory
Default

Strap Posts

For Wrist Strap Installation

 CYCLOPS unit

 Wrist Strap

 Quick guide

 USB cable (data

transfer)

 Cradle

 Charging cable for cradle

 AC Adaptor (optional)

Bluetooth LED

Scan LED

Charging Contacts

Reset Buttom
USB Port

Strap Posts

Battery LED

SCAN Key

FUNCTION Key

2D Bluetooth Scanner

Please read this manual thoroughly and carefully before you start using this device.
Please keep this document in a safe and easy to access place for future reference.

This Guide is to introduce basic ways to use this device:

We have tried to avoid any mistake in this manual. However, if there is any trouble
or loss caused by this manual, we are sorry that we are not able to be responsible
for that. This document is a preliminary version and will be subject to change without
prior notice.

For safe use concern, please pay special attention on the
following notices:

This device has taken safety as first priority during design stage. To avoid any
potential accident, please be cautious on the following alert points:

Danger!

 Please do not put the device into water which may cause short-circuit or fire.
 Please do not stock this device under conditions of high temperature which will

cause the battery to become hot, fire, or broken etc. leading to failure and safety
concerns.

 Please do not put this device in place close to open fire.

Warning!

 Please stop using immediately when there is any unusual smell or overheat

during charging or operation.

 When the charging time is noticed longer than standard required ( CHARGING

LED , RED, is still ON ), please stop charging immediately.

 Please do not use the AC adapter outdoor. Please do not wrap the AC adapter

with cloth which will block heat dissipation and will cause electric shock or fire.

 Please charge this device in place without any water-spray or moisture.
 If there is any dust on the plug of AC adapter, please wipe clean using dry cloth

to avoid fire accident.

 Please do not use wet hand to pull out the AC adapter which might cause

electric shock.

 If the power or USB cable is seriously twisted or broken, please stop using

immediately or it may cause electric shock, short-circuit, or fire.

 Please do not use CYCLOPS 2 AC adapter on any other different devices.

NOTICES:

 Please don’t put it close to open fire or directly under the sunlight as that will

cause enclosure deformation then damage the device.

 Please do not drop this device with strong strike and impact.
 Please stop using immediately when there is any liquid or dew on the device.
 Please make sure the AC adapter is properly plugged into the wall outlet socket

or it might cause electric shock, short-circuit, or fire.

 When you are trying to pull out the plug, please do not pull the cable portion

only but must pull from the connector portion.

 Except charging, please remove the AC adapter plug from the wall AC outlet

socket or it will cause fire accident.

 Please do not put any heavy weight on top of this device as it might cause

device enclosure crack then lead to cutting injury.

Important Notices When Using:

 Before replacing battery pack due to failure, shortened life, or any other unusual

behavior, please confirm if the device has been used correctly and there has no
user operation issue involved.

 It is possible there will be some missed data or interference encountered during

the wireless transmission. It is not a situation can be controlled by the
manufacturer.

 Please do not use any alcohol, benzene, organic solvent, cleaner liquid, or

steel-wool on the surface of this device.

 Please do not scratch the surface of Scan Window in any way as which will

cause problem on barcode scanning.

Bluetooth:

 This device is designed based on Bluetooth standard specifications but

compatibility problem might be encountered if trying to connect with other BT
device.

 Before using this device, please make sure there is no other wireless device

been operated in the same application area within short distance as that may
cause wireless signal interference.

Key Features on the device:

Scanner Window

● LED Indicator Status:

Signal Interference From TV or Radio:

 Sometimes, data transmission or receiving might be failed due to signal

interference from TV or radio near by.

Special Features:

 Compact and light weight design,easy to use and carry.
 CYCLOPS 2 is implemented with CMOS Image scanner which can read both

1D and 2D barcodes.

 CYCLOPS 2 can read inverted barcode.
 You can charge CYCLOPS 2 via AC adapter or through the USB connection of

host device.

 With Bluetooth connection, CYCLOPS 2 can transmit the scanned data to PC,

laptop, or other mobile devices.

 If you use iPhone or iPad (iOS), you can use the software keyboard on them.

Also up to 8,000 scanned data ( size per data: 2048-Byte) can be stored with
its massive storage function.

 When you are using CYCLOPS 2 USB port to connect with host devices, it will

be recognized as a mobile storage device and data stored inside can be easily
retrieved and uploaded.

 Built-in Real-Time Clock (RTC) function can save date & time together with
 scanned data.
 You can also save the configuration file into host device which can be

duplicated into multiple CYCLOPS 2 to simplify the set-up process.

 Buzzer volume can be configured in OFF/ High/ Mid/ Low 4 levels.


Items Inside the Package:

Please confirm if there is any item missing in the package when you open it.
Contact your supplier immediately if there is anything missing or broken.

Operating Modes:

There are three different operating modes for various application needs.

 Real-Time Mode (choice between HID or SPP profile)

Scanned data will be transmitted via Bluetooth to host device right after scanning.
Error message will also be shown if the transmission is failed.

 Batch Mode

Scanned data can be saved into memory after scanning. Stored data can be
retrieved via one of the following two ways:
(1) Using BT SPP program to retrieve data file; or
(2) Connecting CYCLOPS 2 with host device via USB port to retrieve data file.

 Hybrid Mode

Under this mode, CYCLOPS 2 will transfer scanned data automatically (similar to
Real-Time Mode). When CYCLOPS 2 is out of BT communication range or been

Please stop using CYCLOPS2 immediately if any of the abnormal situations
is found. These might be caused by device or unknown failure.

・Power indication is full but it will run out very soon after using.
・The device turned very hot when been charged via AC adapter or

USB port..

disconnected, CYCLOPS 2 will save the scanned data into memory first and

Mode:

Real-Time Mode

Auto Power-OFF time:

3-min

Device Name:

Cyclops 2＋BT address last 4-digits

Authorization:

No

BT Profile:

HID

PIN Code:

0000

Encryption:

No

Date & Time Setup:

OFF

Model

：

CYCLOPS 2

CPU

Atmel AT91SAM9G25 400MHz

Memory

：

32 MB Flash-ROM
Max 8,000 data files (fixed data size: 2048-Byte including date
& time ) can be saved.
128 MB SDRAM

USB ： USB2.0 Full Speed

Bluetooth

：

Ver.2.1+EDR Class2（10-m transmission range）including
SPP/ HID Profile

Scanner

：

CMOS Imager（2D）Motorola SE4710 soft decode

RTC function

Yes, under Batch Mode only

Power
Supply

：
：

Built-in Lithium-Ion battery
It will take about 2.5-hr to complete battery charge with AC
adapter. Battery life is about 8-hr ( QR-code, 256-Byte )
scan

※

1

I/O Interface

：

Micro USB-B type

AC Adapter

：
：

Input 100～240VAC, 50/60Hz
Output DC5V/2A, connector type: Micro USB

Operation
condition
Storage
condition

：
：

Temperature –10～50℃ ( charging temperature 5～35℃）
Humidity 20～85% without condensing
Temperature -25～60℃
Humidity 5～95%
Free Drop

：

1.5-meter

※

2

drop, and 1-meter Tumble Drop 100-Cycle

Sealing

：

IP-54
Regulatory

：

CE/ FCC

Dimensions

：

90（L）mm×38（W）mm×16（H）mm

Weight

：

About 67g

transfer the data file in FIFO order after BT connection been re-established or
CYCLOPS 2 is back in communication range.

Charging the Battery:

CYCLOPS 2 is installed with Lithium-ion battery but not fully charged. Please fully
charge it before the 1st time use under the environmental temperature of 5℃～35℃.

1. Charging with AC adapter :
You can charge CYCLOPS 2 using the AC adapter via charging contacts.
Please be cautious on the orientation of the connection plug.

2. Charging with USB cable :
※ You can also start charging CYCLOPS 2 through AC cable connected with USB

port of host device.

※ Do not operate CYCLOPS 2 while it is being charged via USB port as the power

surge might damage the USB port.

※ The USB connection via AC cable can not be used for data transmission. It is

for battery charging purpose only.

※ It will take about 2.5-hr to fully charge CYCLOPS 2 via the AC adapter.
※ It will take about 3-hr to fully charge CYCLOPS 2 through USB port.

※Please do not charge CYCLOPS 2 through USB hub.
※Please use ONLY the standard AC adapter in CYCLOPS 2 box. It might cause

charging failure or damage the device if using other unauthorized AC adapter.

3. Charging Time :

Charging time required will vary depending on the actual application of
CYCLOPS 2 and the condition of CYCLOPS 2 battery pack.

4. Life span of CYCLOPS 2 Li-ion battery pack :
General life span of Li-ion battery pack is around 300 times charging/discharging
cycles.

Default System Value:

2. Power OFF
When CYCLOPS 2 is standing-by for a period of time, it will be OFF automatically
(default: 3-min) to conserve battery power. There is no “POWER” switch on
CYCLOPS 2.

3. RESET to Default System Value
Please press the RESET button while CYCLOPS 2 is ON (it will be OFF
automatically after been RESET).

4. Bluetooth Communication
Before using Bluetooth communication, please make Paring connection with the
host device.
Default PIN code is “0000”. You can easily start connection through Bluetooth host
device and can be confirmed by the BT LED status indication.
Also, you can scan configuration barcodes to switch communication mode to SPP
Master.

5. Barcode Scanning
Please press the SCAN key to scan the barcode.
Scanning result can be confirmed by the SCAN LED
status. Scanning the setup barcode at the right to
confirm if CYCLOPS 2 is able to scan.

Communication with iPad and iPhone:

Under default, you can easily connect iPad or iPhone using BT HID Profile.
Software keyboard on iPad or iPhone can be displayed or hidden by pressing the
FUNCTION key on CYCLOPS 2.

Detailed Configuration Guide:

On our website, you can download the Detailed Configuration Guide. Please
carefully read the Guide to understand all the details about CYCLOPS 2 and how
to tailor this device further into your applications.http://www.bitatek.com.tw
Since the Configuration Guide can be shown on LCD monitor and CYCLOPS 2 is
designed to read barcodes in various forms, on various media. You can scan those
configuration barcodes directly on LCD screen and set CYCLOPS 2 up
accordingly. It is not necessary to print Configuration Guide on paper as hard copy
for scanning purpose.

Duplication of Configuration Data:

1. You can easily duplicate the Configuration data from one CYCLOPS 2 to the other
unit. This will provide an easy and accurate way for multiple units CYCLOPS 2
operations.

RESET to Default System Value:

 Please scan the “DEFAULT” setup barcode at the right.
 As the memory setup parameter cannot be deleted,
 please initialize the memory first then delete the data in the memory.
 When CYCLOPS 2 has been configured as

“ reverse barcode scanner”, please scan the
“reversed DEFAULT” setup barcode at the right.

Memory Initialization:

Memory Initialization will delete all data and values in the memory.
Please scan the barcode at the right side which can
initialize the memory.

※ Please note: there is no way to restore the data

deleted after memory initialization.

Simple ways to start CYCLOPS II:

1. Power ON
Press the SCAN button for 3-second to turn ON and Scan LED will light up as well.
After power ON, scan LED will go off and CYCLOPS 2 is standing-by for scanning.

2. Configure the first unit CYCLOPS 2 through setup barcodes scanning.

3. Connect the first CYCLOPS 2 unit with host device through USB cable to transfer
the Configuration data to host device (SYSTEM.CFG file).

4. Connect the other CYCLOPS 2 unit with host device through USB cable to
download the configuration data from host device.

Long Term Storage of CYCLOPS 2:

 Please store this device in dry environment.
 When the device is under Batch Mode and been kept OFF for an extended

period of time, Date & Time data might be RESET due to the battery power
been drained.

 Always charge CYCLOPS 2 before using and refer to the Configuration Guide

to set Date & Time properly.

How to Dispose CYCLOPS 2 Properly:

CYCLOPS 2 is implemented with Li-ion battery which is recyclable and
important resource.
If you send CYCLOPS 2 back to your supplier, it will be disassembled and the Li­ion battery will be recycled. If you want to dispose this device by yourself, please
remember to pull out the battery and recycle it properly following regulations and
rules set up by your local authority.

 The way to disassemble CYCLOPS 2:

Remove the four screws on the back of CYCLOPS 2.
Open the enclosure and remove the screws fixing the battery pack then you
can pull out the battery.

※Notice when you are disassembling:

Please tape the metal part of the battery for proper insulation to avoid short­circuit.

Specification:

※1 One scan per 6-second under room temperature and Bluetooth connection.
※2 Free drop on concrete, 3 times per 6 surface at room temperature

Trademark

 Bluetooth & Logo are Trademarks of Bluetooth SIG, INC.
 iPad、iPhone and iOS are Trademarks of Apple Inc.
 ALL company name or logo appearing in this document are all intellectual property

rights of BITATEK CO.,LTD.
※ All copy rights are reserved: without any agreement of BITATEK, it is not allowed
to copy or quote any part or all content of this document.

Bitatek Co. Ltd. has been acquired by iMotion Group in 201 9.
Ow ners hip of all pr oduc ts and tra dema rks of Bitatek Co. Ltd. shall be assumed by iMotion Inc. and its
subsidiaries unless otherwise specified.

2020/02/18