Bissell 9400 User Manual

Carpet cleaning

1. While pressing the trigger, make one slow forward wet pass and another one back

2. Release the trigger and make one slow forward and backward pass over the same area. Repeated passes will help aid in dry time

3. Continue passes until cleaning area is complete

4. When the dirty water reaches the “FULL” line on the tank, it is time to empty

5. Empty dirty water by removing tank from base of machine. Carry to sink or outside to dispose of water. Unlatch top of tank and pour dirty water through triangle shaped opening in corner

8920, 8930, 8960,

9200, 9300, 9400 SERIES

BISSELL is happy to be of service.

visit the website for helpful instructions at

www.bissell.com

PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE

PLEASE KEEP FOR FUTURE REFERENCE

6. Rell as needed, following steps 4 & 5 under "Before you begin cleaning"

5. 6.

Cleaning with attachments

1. Set ReadyTools dial to the “TOOLS” setting

2. Attach the cleaning tool to the end of the hose

3. Clean by pressing the trigger to spray solution onto the area to be cleaned

4. Slowly scrub the tool back and forth over the soiled surface

5. Tilt the tool forward to suction liquid

6. When the dirty water reaches the “FULL” line on the tank, follow instruction #5 under “Carpet Cleaning” to empty tank

7. When cleaning is complete, remove and rinse tool in warm water

Quick Start

Guide

WARNING:

Refer to the enclosed user guide for complete instructions and important safety notices.

Package contents:

a. Machine Base & 2 tank system b. Upper Handle c. 4 Screws - taped to handle d. Upper Hose Rack

Phillips head screw driver is needed for assembly

e. Lower Hose Rack f. Tool Attachment(s)

(varies by model)

g. Formula

(varies by model)

Refer to the User’s Guide for full instructions on how

to clean, store and maintain your machine

For additional tips and troubleshooting

Please refer to User's Guide

Earn BISSELL rewards! Register your product today!

Visit: www.bissell.com

BISSELL Homecare, Inc. P.O. Box 1888 Grand Rapids, MI 49501

1204357

Assembly Before you begin cleaning

1. Slide upper handle onto machine base

2. Screw 3 screws into the marked holes

3. Place upper hose rack onto back of upper handle, and secure with screw

4. Place lower hose rack onto back of upper handle by pushing in and sliding down until it snaps rmly into place

5. Wrap power cord and ex hose

6. Keep ex hose snugly in place by using the hose secure latch

7. Attach tool to hose grip (extra tool storage on back)

1. Move furniture to another area if cleaning an entire room

2. Remove large dirt and debris from carpet (See User's Guide for more details)

3. Pre-treat spots & stains and heavy trafc areas (optional- see User's Guide)

4. Fill the clean water tank 4a. Unlatch the top by lifting up on tank latch 4b. Remove the top 4c. Fill the bladder with clean hot tap water 4d. Re-attach top by hooking the lip of the tank top into the groove of the

tank bottom and secure the latch

5. Fill the formula tank with water and BISSELL 2X formula 5a. Remove formula tank and unscrew the cap and insert 5b. Fill with water to the WATER line 5c. Fill with BISSELL 2X formula to the FORMULA line 5d. Replace cap and insert and place back into formula tank holder

6. Set Custom Clean Dial (located on the foot of the unit or on the upper handle)

7. Set ReadyTools Dial ("FLOOR CLEANING” for carpet cleaning or “TOOLS”

for cleaning with the hose and tool)

8. Plug into outlet, and turn the power and heater (if desired) switch on

Your assembly is now complete.

6. 7.

a. Tough Stain Brush

9. If using the heater, let the machine warm up for 1 minute before cleaning

4a.

4d.

For complete user's guide, visit www.bissell.com

4b.

5a.

4c.

5b.

Power

Heater