Bissell 2768 User Guide

Series 2768

Welcome to BISSELL

®

Safety Instructions

WARNING: TO REDUCE THE RISK OF

FIRE, ELECTRIC SHOCK OR INJURY:

Use indoors only.
Do not use for any purpose other than described

in this user guide.
Use only manufacturer’s recommended

accessories.
Do not use with damaged cord or plug.
If appliance is not working as it should, or has

been dropped, damaged, left outdoors, or
dropped into water, have it repaired at an
authorized service center.

Do not move or carry by cord, use cord as a
handle, close a door on cord, or pull cord around
sharp corners. Keep cord away from heated
surfaces.

Do not run cord under carpeting. Do not cover
cord with throw rugs, runners or similar cover­ings. Arrange cord away from tra c areas so it
will not be tripped over.

Do not unplug by pulling cord. To unplug, grasp
the plug, not the cord.

Do not handle plug or appliance with wet hands.

Do not put any object into openings. Do not use
with any opening blocked; keep openings free
of dust, lint, hair and anything that may reduce
airfl ow.

Keep hair, loose clothing and fi ngers away from
openings.

Turn OFF device controls before unplugging the
appliance.

Do not use appliance in an enclosed space fi lled
with vapors given o by oil-based paint, paint
thinner, moth-proofi ng substances, fl ammable
dust, or other explosive or toxic vapors.

Keep appliance on a level surface.
Do not immerse the unit in water or other

liquids, do not pour liquids into or around the
unit or openings.

Do not use the appliance near water or in a damp
or wet location.

This appliance has a polarized plug (one blade
is wider than the other). To reduce the risk of
electric shock, this plug is intended to fi t in a
polarized outlet only one way. If the plug does
not fi t fully in the outlet, reverse the plug. If it still
does not fi t, contact a qualifi ed electrician. Do
not attempt to defeat this safety feature.

Do not use the appliance with any dimmer switch
or solid state speed control device.

Read & Save These Instructions

WARNING

This model is for household use only.
Plastic fi lm can be dangerous. To avoid danger of su ocation, keep away from children.
Do not plug in your air purifi er UNTIL you are familiar with all instructions and operating procedures.
To reduce the risk of electrical shock, turn power OFF and disconnect polarized

plug from electrical outlet BEFORE performing maintenance or troubleshooting checks.

4

Control Dial & Digital Display

1

2

1 Control Dial

• Press the power button
in the center of the dial
to turn the air320 ON
an d O FF.

• To adjust fan speed,
twist the dial clockwise.

• To reset the fi lter(s),
press and hold the
power button for 3
seconds.

2 Digital Display

Air Quality

The three digit number on the front of the display is a real-time
reading of your indoor air quality. See page 6 for more details.

NOTE: 002 is the resting, lowest number.

Fan Speed

The air320 has 5 di erent fan speeds ranging from low to high.
It also has an auto mode (
Control Dial. For more details on Auto Mode, see page 6.

Night Mode

The air320 has an automated Night Mode. As less light enters a
room, the lights on the Digital Display of the air320 will turn o
to help create a peaceful sleeping environment.

) which can be selected using the

A

5

System

®

When set to Auto Mode, the BISSELL® air320 uses its CirQulate® System to provide optimum fi ltration
based on your home’s indoor air quality.

CirQulate uses the air320’s PM 2.5 sensor to measure microscopic particles like dust, pollen and even
smoke.

Then, CirQulate’s Digital Air Quality Feedback Display provides both a numerical and colored
indication of your homes indoor air quality in real-time, making your once invisible concerns, visible.

Good Air Quality Moderate Air Quality Poor Air Quality

Need Some Help?

For more support and information, please visit support.BISSELL.com.

6

Filter Reset Indicator & Filter Reset

If your digital display is showing F
to be replaced.

Replace E ciency Filter Replace Both FiltersReplace Carbon Filter

After replacing your fi lter(s), press and hold down the power button for 3 seconds to reset the fi lter(s).
Once reset, the air320 will beep and the

•

1 and/or F•2, this means that either one or both of your fi lters needs

F•1 and/or F•2 will no longer show on the digital display.

7

Maintenance & Care

Filter Replacement

1

Each fi lter has easy pull tabs. The tabs should face outward. Insert the activated carbon fi lter before
inserting the pleated fi lter.

NOTE: Filter life varies based on run time and existing air conditions. It is recommended to replace
both the pleated and activated carbon fi lter once every six months. It is also recommended to
occasionally vacuum the fabric front panel to remove dust.

2

3

4

5

Particulate Sensor Cleaning

1

For accurate air quality display readings, the sensor screen located inside the sensor door should be
removed and gently cleaned with a cotton swab once every six months.

2

3

4

8