Bissell 2503 Quick Start Guide
QUICK START GUIDE
40"
79"
40"
EV675 ROBOTIC VACUUM
Assembly Instructions
Setting Up Your Robot Set the ClockPair the Remote to the Robot
2503 SERIES
WARNING
Refer to the enclosed user guide for complete
instructions and important safety notices.
1 12 2
NOTE : Be sure to install batteries in the remote.
Place the back of Docking
Station firmly against a wall.
Ensure there are at least 40
inches to one side, 40 inches
to the opposing side and no
obstructions in front of the
Docking Station.
Insert the Docking Station
power adapter plug into
the port on the side of the
Docking Station and then
plug the other end into the
wall outlet. Turn ON the
unit’s Power Switch and put
on the Docking Station.
The first charge will take
4-5 hours.
While the Power Switch
on the side of the robot is
OFF(0), press and hold the
play button on the remote
for 5 seconds until the clock
icon on the display flashes.
Package Contents
Continue to hold the play
button and turn the robot
ON (I).
NOTE: The robot will beep
three times to indicate that
it has successfully paired.
1 2 3
Set the time by
pressing and
holding the clock
button on the
Remote Control
until the clock icon
on the Remote
Control display
begins to flash.
Use the
directional
arrows to set the
hour and minute.
Press the clock
button again to
save the time
setting.
NOTE: The robot
will beep once to
confirm the time
has been saved.
B I S S E L L®
EV675
NOTE: Standard accessories may vary by model.
161-8186 Rev 01/19
Docking
Station
Power Adapter
(Charger)
Remote Control
(2 AAA B atteries included)
Edge Cleaning
Brushes
Rechargeable
Li-Ion Battery
(Pre-installed)
Dust Bin
(Pre-installed)
Pleated Filter
(Located inside Dust Bin)
(Located inside Dust Bin)
Cleaning ToolFoam Filter
QUICK START GUIDE
reference the User Guide or visit
www.BISSELL.ca
Schedule Cleaning Sessions Getting Ready to Clean
NOTE: Be sure the clock is set to the correct time before scheduling cleaning sessions.
1 32
Press the schedule button
on the Remote Control. The
icon will begin to flash on the
Remote Control display.
NOTE: To cancel a scheduled cleaning session, press and hold the schedule button on the remote.
Use the directional arrows to
set the hour and minute for
your robot to start cleaning.
Press the schedule button
again to save the schedule
setting.
NOTE: The robot will beep
once to confirm the schedule
has been saved.
With Remote Control
NOTE: Be sure the Power Switch on the Robot is set to the ON position.
You can change the cleaning pattern of the robot by pressing one of the following buttons:
Auto Mo de
Robot wi ll drive in a s traigh t path unti l it encounters an obstacle and ch ange direction.
Spiral Mode
Best fo r concentrated cl eanin g.
Wall Mode
Best fo r clean ing along walls and edge s.
Single Room Mode
Best fo r clean ing a single room . It’s re comme nded th at you clos e any doors to contain the robot.
Manual Mode
Best fo r direc ting the robot to a par ticular area .
Return to Dock
Press to re turn the robot to the D ocking Station.
Without Remote Control
1 32 4
For further instructions
Press the Power
Switch to the ON(I)
position.
Press the Start/
Stop Button on the
top of the robot to
start cleaning.
When finished,
press the Start/
Stop Button again
to stop the robot.
Status Light Notifications
Status Light Colour Status
Breathing Blue Charging
Power Light O Robot Fully Charged
Solid Blue Cleaning
FOR ADDITIONAL INFORMATION ON ERROR NOTIFICATIONS AND OTHER TROUBLESHOOTING TIPS,
PLEASE REFER TO PAGES 12 AND 13 IN THE USER GUIDE.
Status Light Colour Status
Flashing Blue Returning to Docking Station
Flashing Red Error: Check Cliff Sensors, Battery Power Low, Robot is Trapped
Solid Red Error: Check Wheels, Edge Cleaning Brushes, Brush Roll, and Bumper
When the vacuum
is in standby mode,
press the Start/
Stop button twice
continuously. The
vacuum goes into
recharging mode
with the
flashing blue.
button
Loading...