Page 1
TURBOCLEAN
POWERBRUSH
___________
USER GUIDE
2222F
I
N
N
G
A
E
E
L
C
E
M
O
H
E
S
T
.
X
P
E
R
T
S
.
A
.
S
.
1
U
8
7
6
Page 2
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING YOUR APPLIANCE.
Unplug from outlet when not in use and before conducting maintenance. When using an electrical
appliance, basic precautions should be observed, including the following:
» Do not handle plug or appliance with wet hands.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK
OR INJURY:
» This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory
or mental capabilities or lack of
experience and knowledge if they have
been given supervision or instruction
concerning use of the appliance
in a safe way and understand the
hazards involved. Cleaning and user
maintenance shall not be made by
children without supervision.
» Children should be supervised to ensure
that they do not play with the appliance.
» Keep hair, loose clothing, fingers, and
all parts of body away from openings
and moving parts of the appliance and
its accessories.
» Unplug from electrical socket when
not in use, before cleaning, maintaining
or servicing the appliance, and if your
appliance has an accessory tool with
a moving brush, before connecting or
disconnecting the tool.
» If the supply cable is damaged, it must
be replaced by the manufacturer, its
service agent, or similarly qualified
person in order to avoid a hazard.
» Do not run appliance over cable, a
hazard may occur.
» Do not leave appliance when plugged in.
» Do not use with damaged cable or plug.
» Do not pull or carry by cable, use cable as a handle,
close door on cable, or pull cable around sharp edges
or corners.
» Keep cable away from heated surfaces.
» To unplug, grasp the plug, not the cable.
» Turn OFF all controls before unplugging.
» Plastic film can be dangerous. To avoid danger of
suffocation, keep away from children.
» Use only as described in this user guide.
» Use only manufacturer’s recommended attachments.
» Do not immerse in water or liquid.
» If appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into
water; do not attempt to operate it and have it
repaired at an authorized service center.
» Do not put any object into openings.
» Do not use with any opening blocked; keep free of
dust, lint, hair, and anything that may reduce air flow.
» Use extra care when cleaning on stairs.
» Do not use to pick up flammable or combustible
liquids, such as petroleum, or use in areas where they
may be present.
» Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, etc).
» Do not use appliance in an enclosed space filled with
vapours given off by oil-based paint, paint thinner, some
moth-proofing substances, flammable dust, or other
explosive or toxic vapours.
» Do not pick up hard or sharp objects such as glass,
nails, screws, coins, etc.
» Keep appliance on a level surface.
» Do not pick up anything that is burning or smoking,
such as cigarettes, matches or hot ashes.
» Have servicing performed by a qualified repair person
using only identical replacement parts. This will ensure
that the safety of the product is maintained.
» Operators shall be adequately instructed on the use
of these machines.
» Always connect to a properly earthed electrical socket.
Do not modify earthed plug.
» Liquid must not be directed towards
equipment containing electrical components.
» Do not immerse. Use only on surfaces moistened
by the cleaning process. Use only BISSELL cleaning
products intended for use with this machine.
» Use only the type and amount of liquids specified
under the operations section of this guide.
» Use indoors only.
» Have servicing performed by a qualified repair person
using only identical replacement parts. This will ensure
that the safety of the product is maintained.
» Operators shall be adequately instructed on the use
of these machines.
SAVE THESE INSTRUCTIONS
FOR OPERATION ON A 220-240 VOLT A.C. 50-60 HZ POWER SUPPLY ONLY.
This model is for household use only.
BISSELL.com
2
Page 3
Thanks for buying a BISSELL® carpet washer!
We love to clean and we’re excited to share one of our innovative products with
you. We want to make sure your carpet washer works as well in one year as it
does today, so this guide has tips on using, maintaining, and if there is a problem,
troubleshooting.
In just a few simple assembly steps, you’ll be ready to deep clean. Flip to page 5
and let’s get started!
What’s In The Box?
Upper Body Lower Body
Handle Post
NOTE: Standard accessories may vary by model. To identify what should be included with
your purchase, please refer to the “Carton Contents” list located on the carton top flap.
Safety Instructions...........2
Product View ................4
Assembly ...................5
Cleaning Formulas...........6
Clean Water Tank
Maintenance & Care .....10-12
Troubleshooting ............14
Guarantee..................16
Consumer Care.............16
Trial-Size Formulas
Two Screws
(taped to handle)
Operations ................7-9
BISSELL.com
3
Page 4
Product View
Lower Body
Collection
Tank
Handle
Removable
Nozzle
Collapsible
Handle Lock
Upper Body
Carry Handle
Vent Cover
(Foam Filter)
Collection
Tank Latch
Clean Water
Tank
Recline
Pedal
Spray
Trigger
Power
Cord
Collection
Tank Latch
Power
Pedal
4
BISSELL.com
Page 5
Assembly
WARNING
Do not plug in your carpet washer until you are familiar with all instructions and operating
procedures.
A Phillips-head screwdriver is required for Assembly in Step 2.
1
Slide Upper Body
onto Lower Body.
4
Be sure to secure upper
handle before lifting.
Rotate lock collar to secure.
2
Secure with screws.
5
Place Clean Water
Tank on back of
machine, so it “clicks”
into place.
3
Slide upper Handle Post
into the body by aligning
the pin and sliding the post
down into place.
6
Wrap Power Cable.
Tips Before Carpet Cleaning
• If cleaning an entire room, consider moving your furniture to another area.
• Remove loose dirt and impediments before cleaning.
• Pretreat stains with BISSELL® Pretreat to improve performance on coee
stains and ground-in dirt.
BISSELL.com
5
Page 6
Cleaning Formula
Keep plenty of BISSELL® formulas on hand so you can clean whenever it fits your schedule.
Always use genuine BISSELL formulas in your machine. Other formulas may harm the machine
and void the guarantee.
Carpet Cleaning Formulas
Wash & Protect Wash & Refresh
Pro Stain & Odour
Professional strength to
remove extra tough stains
and odours.
Wash & Remove
Pro Pet Urine
Eliminator + Oxy
Permanently removes stains
and odors at the source with
the power of Oxy.
Pet Stain & Odour
Removes tough pet stains
and odours.
Allergen
Helps remove pet dander,
pollen and dust mite waste
allergens.
Pretreat
Pretreat spots and stains to improve carpet
cleaning performance.
Stain Pretreat
Loosens set-in stains &
odours before carpet
washing.
Certain t rademarks us ed under licens e from The Proc ter & Gamble Compa ny or its affilia tes.
Pet Stain Pretreat
Loosens tough pet stains
& odours before carpet
washing.
Stain & Odour
Removes tough stains and
odours.
Ambipur Blossom &
Breeze
Powerful cleaning with a
refreshing spring scent.
Boost
Add Boost carpet cleaning formula enhancers
to any formula to increase its effectiveness.
Oxy Boost
Add to formula for
permanent stain removal.
WARNING To reduce the risk of fire and electric shock due to internal component damage, use only BISSELL
formula intended for use with this machine. Use of cleaning formulas that contain eucalyptus, lemon or pine oil may damage this
appliance and void the guarantee. Chemical spot cleaners or solvent-based soil removers should not be used. These products may
react with the plastic materials used in your carpet washer causing cracking or pitting.
BISSELL.com
6
Page 7
Filling the Clean Water Tank
1
Lift the Clean Water
Tank straight up and
away from the Lower
Body to remove.
3
Fill with warm tap water to the WATER
line. Fill the rest of the tank with BISSELL
Formula to the FORMULA line.
A few notes about filling the clean water tank:
• Fill with warm (140°F/60°C MAX) tap water and add the appropriate
BISSELL® formula. DO NOT USE BOILING WATER. DO NOT HEAT WATER
OR TANK IN MICROWAVE.
2
Unscrew the cap at the bottom of
the Clean Water Tank.
4
Replace and tighten
the cap, then return
the Clean Water Tank
to Lower Body.
It will “click” into
place when seated
properly.
NOTICE: Do not overwet carpet. Be careful not to run over loose objects or edges
of area rugs. Stalling the brush may result in premature belt failure.
NOTE: Do not substitute BISSELL® Formula cleaning solution with other household
cleaning products.
Pour in more power with BISSELL OXY Boost
• Fill tank with water and BISSELL cleaning formula.
• Add 29.5 ml of BISSELL OXY Boost per 1.89 Liter of water.
• TurboClean PowerBrush has a 1.89-Liter tank.
BISSELL.com
7
Page 8
Cleaning Your Carpet
Important! Please check manufacturer’s tag before cleaning area rugs for any
specialized cleaning instructions. We do not recommend deep cleaning delicate,
silk, wool, antique, or area rugs, without a manufacturer’s tag.
1
Plug into a proper outlet.
2
Extend the
Collapsible Handle Post
by turning the collar
counter-clockwise
and lifting the handle
up. Turn the collar
clockwise to secure.
IMPORTANT BEFORE USE: Make sure the Handle Post is fully extended up and
the collar lines up with the lock symbol before you begin cleaning.
3
With foot, press the grey Recline Lever
located next to Power Pedal.
4
With foot, press the red Power Pedal,
located on the back of the machine.
5
8
Cleaning Pass:
1. While pressing the trigger, make one slow
forward wet pass and another one back.
2. Release the trigger and make one slow forward
and backward pass over the same area.
3. Repeat steps 1 and 2 until solution being pulled
up appears clean.
4. Empty the Dirty Water Tank when dirty water
reaches the full line, and fill with fresh warm water
and formula when the Clean Water Tank is empty.
BISSELL.com
Page 9
Emptying the Dirty Water Tank
WARNING
To reduce the risk of fire, electric shock or injury, turn power OFF and disconnect plug from
electrical outlet before performing maintenance or troubleshooting.
1
With foot, press the red Power Pedal,
to turn OFF machine and then unplug.
3
Carefully remove tank by lifting up
on the Carry Handle.
5
2
Release Dirty Water Tank Latches
(on each side) by pulling up from the
bottom of latch and then out.
4
Carry the Dirty Water Tank to a sink.
To empty, tilt tank and pour out contents
using the opening at the back of tank.
6
Rinse the Dirty Water Tank thoroughly
and replace on machine. Secure
latches on both sides of the tank.
Refill the Clean Water Tank and
continue cleaning, or if you’re done
cleaning, wait for the pieces to dry
before storing your machine.
BISSELL.com
9
Page 10
Cleaning Your Machine After Use
WARNING
To reduce the risk of electric shock, turn power OFF and disconnect plug from electrical
outlet before performing maintenance or troubleshooting checks.
1
Unplug the machine. Remove and rinse the Dirty Water Tank thoroughly.
3
Remove tank vent & foam
filter (located on top of the
Dirty Water Tank) and rinse.
5
Remove lint and hair from
red gasket in base of machine.
(Do not remove gasket.)
2
4
6
To remove and clean the
nozzle, keep the Dirty Water
Tank off of the machine.
Gently pull the two tabs that
point up near the front of
the machine. The nozzle will
unhook to remove. Rinse under
running water. When finished,
slightly tilt the machine so
the foot raises up so you can
align the nozzle hooks at
the floor of the machine.
Rotate the nozzle up to clip
back into place.
Once the parts have been
rinsed clean and dried,
replace the Dirty Water Tank
to the base of the machine
and secure with both latches.
Wrap power cable around
Quick Release Cable Wrap
on side of the machine. Wipe
all surfaces with a soft cloth
and store machine upright in
a protected, dry area.
NOTICE: To reduce the risk of a leaking condition, do not store machine where
freezing may occur. Damage to internal components may result.
BISSELL.com
10
Page 11
Replacing the Belts & Brush Rolls
WARNING
To reduce the risk of electric shock, turn power OFF and disconnect plug from electrical
outlet before performing maintenance or troubleshooting checks.
What you will need: 1 Phillips-head screwdriver & 1 flathead screwdriver
1
Turn the machine OFF and
unplug from wall outlet.
3
Lay machine down to access the bottom of the machine. With a
Phillips-head screwdriver, unscrew the belt cover and remove.
4
2
Remove both the Clean and Dirty Water Tanks.
5
If you want to replace or clean the
Brush Roll, remove the belt by slightly
lifting the Brush Roll to maneuver the
belt and remove it. If the belt is broken
and needs to be replaced, remove it
and replace with a new belt.
When removing the Brush Roll,
the Brush Roll cap will come with it.
Do not lose this part.
BISSELL.com
11
Page 12
Replacing the Belts & Brush Rolls (cont.)
Brush Roll
Washers
Brush Roll
Endcap
7
left
side
Clean or replace the Brush Roll and belt. When finished, reassemble them to the machine.
Insert the brush into the right side endcap. Adjust the right side of the brush into place
and tuck the left Brush Roll cap (separate piece that attaches to Brush Roll) into place.
8
Maneuver the belt to wrap
around the pulley. Wrap the belt
around the cog of the Brush
Roll. Secure the Brush Roll into
place by sliding the square piece
to align the Brush Roll.
right
side
9
Reattach belt cover and screw into place.
NOTE: Manually rotate brush to make sure it rotates freely and the belt is aligned.
BISSELL.com
12
Page 13
Hard Floor Cleaning (select models only)
WARNING
To reduce the risk of fire and electric shock when cleaning a hard floor, the BISSELL® hard
floor tool must be used and it must only be used with BISSELL Wash & Shine Floor Cleaner
intended for use with this appliance.
1
With foot, press the red Power Pedal,
to turn OFF machine and then unplug.
3
Release Dirty Water Tank Latches
(on each side) by pulling up from the
bottom of latch and then out.
5
2
Remove the Clean
Water Tank by lifting
straight up and away
from Lower Body.
Fill the tank using
water and BISSELL
Wash & Shine Floor
Cleaner formula
for cleaning the
hard floor.
4
Attach the hard floor tool by hooking it
into the front of the nozzle. Rotate down
until it snaps into place.
6
Return both tanks to the machine and
plug into a proper outlet.
Follow the “Cleaning Pass” instructions
on page 8, step 5.
BISSELL.com
13
Page 14
Troubleshooting
WARNING
To reduce the risk of electric shock, turn power OFF and disconnect plug from electrical
outlet before performing maintenance or troubleshooting checks.
Problem Possible causes Remedies
Clean Water Tank is empty. Refill tank with water and formula.
Reduced
spray OR
no spray
Carpet
washer not
picking up
cleaning
solution
Lint screen on Clean Water Tank
cap clogged.
Spray nozzle clogged. Clean spray nozzle by rinsing
Upper handle is not in the upright
and locked position.
Clean Water Tank not properly
seated on machine.
Upper handle assembly not fully
installed.
Dirty Water Tank is not aligned/
secured.
Dirty Water Tank is full. Empty tank.
Removable Nozzle installed
improperly.
Removable Nozzle full of debris. Unplug machine, remove nozzle and
Red lint screen under Dirty Water
Tank is clogged.
Soak Clean Water Tank cap in warm
water and then rinse under running
wa t e r.
under water.
Rotate the Collapsible Handle Lock,
pull handle up and return the handle
lock to the locked position.
Remove tank, ensure cap is tightened
properly, and reinstall tank until you
hear a “click”.
Unscrew and reassemble upper
handle body to lower base to
ensure both assembly screws are
fully-seated. Ensure trigger on handle
has tension.
Check tank alignment and secure
with side latches.
Unplug machine and align two
"hooks" into bottom first, then snap
into place on top.
rinse under running water.
Remove debris from lint screen.
14
BISSELL.com
Page 15
Notes
BISSELL.com
15
Page 16
Consumer Guarantee
This guar antee gives you specif ic legal rights , in addition to right s you may
have under th e Australian Consu mer Law. If you need add itional instruc tion
regardin g this guarantee or h ave questions regar ding what it may cover,
please co ntact your local B ISSELL® Consumer Ser vices on the details s et out
belo w.
Limited 2 Year Guarantee
(from the date of purchase by
original purchaser)
Subject to t he *CONDITIONS id entified below, BISS ELL will repair or rep lace
(with new, refurbished, lightly used, or remanufactured components or
produc ts), at BISSELL’s option, free of c harge, any defective o r malfunction ing
part du e to manufacturer d efect. This guar antee applies to pro duct used for
personal purposes, and not commercial or rental service. This guarantee does
not apply to f ans or routine main tenance or consuma ble components s uch as
filters , belts, brush ro lls, etc., damage or m alfunction ca used by negligence ,
abuse, ne glect, unauth orized repair, or any othe r use not in accordan ce with
the user gu ide. BISSELL recom mends that the ori ginal packaging b e kept
for the dur ation of the guarante e period in case su ch need arises with in the
guarante e period that the item n eeds re-packin g and transport ation.
It may be nece ssary to obtain s ome of your person al information, s uch as a
mailing a ddress, to fulfi ll terms of this guaran tee. Any personal d ata will be
handle d pursuant to BISSE LL’s Priv acy Policy, which can b e found at
BISSELL.com.
*CONDITIONS OF THE GUARANTEE
Subject to w hether such loss i s reasonably fores eeable, BISSEL L and its
in-coun try distributor s are not liable for in cidental or conseq uential damage s
of any nature a ssociated with the us e of this product.
FOR AUSTRALIAN CONSUMERS ONLY:
OUR GOODS CO ME WITH GUARANT EES THAT CANNOT BE E XCLUDED UNDER
THE AUSTR ALIAN CONSUME R LAW. YOU ARE ENTITLED TO A R EPLACEMENT
OR REFUND FOR A MAJOR FAILURE AND FOR COMPENSATION FOR ANY OTHER
REASONABLY FORESEEABLE LOSS OR DAMAGE. YOU ARE ALSO ENTITLED
TO HAVE THE GOOD S REPAIRED OR REPLAC ED IF THE GOODS FAIL TO BE OF
ACCEPTABLE QUA LITY AND THE FAIL URE DOES NOT AMOU NT TO A MAJOR
FAILURE.
THIS GUAR ANTEE IS IN ADDITI ON TO OTHER RIGHTS OR R EMEDIES UNDER L AW.
NOTHING IN T HIS GUARANTEE E XCLUDES, LIMIT S OR MODIFIES AN Y LIABILITY
OF BISSEL L WHICH IS IMPOSED BY L AW, OR L IMITS OR MODIFI ES ANY REMEDY
AVAILABLE TO TH E CONSUMER WHICH IS GR ANTED BY LAW. TO MAKE A CL AIM
UNDER TH IS GUARANTEE CONTACT B ISSELL AUSTRA LIA PTY LTD (DETAIL S
BELOW). CON TAC T BISSELL PRIOR TO R ETURNING ANY GO ODS. WHERE AGREED,
BISSELL W ILL REIMBURSE R EASONABLE P OSTAGE / HANDLING COST S (IF ANY)
FOR RET URNING GOODS TO BIS SELL. TO CLAIM EX PENSES INCURR ED IN MAKING
A CLAIM UN DER THIS GUARANT EE PLEASE PROV IDE BISSELL WITH A COP Y OF
THE RECEI PT OF THE EXPENSE S BY EMAIL OR POST.
Consumer Care
If your BISSELL® product should require service or to claim under our limited guarantee,
please contact us as follows:
Website and Email:
www.BISSELL.com.au
www.BISSELL.co.nz
Telephone:
Australia: 1300-247-735
New Zealand: 0800-247-735
Replacement parts and accessories are available for purchase.
To purchase visit BISSELL.com.
Write:
BISSELL AUSTRALIA PTY LIMITED
42 Rocco Dr.
Scoresby 3179
Victoria
Australia
Visit the BISSELL website: BISSELL.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number:
Please record your Purchase Date:
NOTE: Please keep your original sales receipt. It provides proof of the date
of purchase in the event of a guarantee claim. See guarantee for details.
©2020 BISSELL Inc.
All rights reserved. Printed in China
16
Part Number 1623135 02/20 RevB
Loading...