Page 1
PET
®
ADVANCED
PROHEAT
2009 SERIES
Page 2
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS
BEFORE USING YOUR DEEP CLEANER.
When using an electrical appliance, basic precautions should be
observed, including the following.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY:
» Unplug from electrical socket when not
in use and before cleaning, maintaining
or servicing the appliance.
» This appliance can be used by children
aged from 8 years and above and persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning
use of the appliance in a safe way
and understand the hazards involved.
Cleaning and user maintenance shall not
be made by children without supervision.
» Children should be supervised to ensure
that they do not play with the appliance.
» If the supply cable is damaged, it must
be replaced by the manufacturer, its
service agent or similarly qualified
persons in order to avoid a hazard.
» Do not run appliance over cable.
» Keep hair, loose clothing, fingers, and all
parts of body away from openings and
moving parts of the appliance and its
accessories.
» Use only the type and amount of liquids
specified under the Operations section of
this guide.
» Do not leave appliance when plugged in.
» Always connect to a properly earthed electrical socket.
Do not modify earthed plug.
» Use indoors only.
» Do not allow to be used as a toy.
» Use only as described in the user guide.
» Use only manufacturer’s recommended attachments.
» Do not use with damaged cable or plug.
» Do not immerse in water or liquid.
» If appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into
water; do not attempt to operate it and have it
repaired at an authorized service center.
» Liquid or steam must not be directed towards
equipment containing electrical components.
» Do not pull or carry by cable, use cable as a handle,
close door on cable, or pull cable around sharp edges
or corners.
» Keep cable away from heated surfaces.
» Do not unplug by pulling on cable.
» To unplug, grasp the plug, not the cable.
» Do not handle plug or appliance with wet hands.
» Do not put any object into openings.
» Do not use with any opening blocked; keep free of
dust, lint, hair, and anything that may reduce air flow.
» Turn off all controls before unplugging.
» Use extra care when cleaning on stairs.
» Do not use to pick up flammable or combustible
liquids, such as petrol, or use in areas where they
may be present.
» Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, etc.)
» Do not use appliance in an enclosed space filled
with vapors given off by oil base paint, some
mothproofing substances, flammable dust, or other
explosive or toxic vapors.
» Do not pick up hard or sharp objects such as glass,
nails, screws, coins, etc.
» Keep appliance on a level surface.
» Do not carry appliance while in use.
» Unplug before attaching the TurboBrush™ tool.
» If your appliance is fitted with a nonrewireable BS
1363 plug it must not be used unless a 13 amp (ASTA
approved to BS 1362) fuse is fitted in the carrier
contained in the plug. Spares may be obtained from
your BISSELL supplier. If for any reason the plug is cut
off, it must be disposed of, as it is an electric shock
hazard should it be inserted into a 13 amp socket.
WARNING
TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, USE INDOORS ONLY . DO NOT IMMERSE. USE
ONLY ON SURFACES MOISTENED BY THE CLEANING
PROCESS. USE ONLY BISSELL CLEANING PRODUCTS
INTENDED FOR USE WITH THIS MACHINE.
WARNING
TO REDUCE THE RISK OF FIRE AND
ELECTRIC SHOCK, ALWAYS INSTALL FLOAT
BEFORE ANY WET PICK-UP OPERATION.
SAVE THESE INSTRUCTIONS
FOR OPERATION ON A 220-240 VOLT A.C. 50/60 HZ POWER SUPPLY ONLY.
This model is for household use only.
www.BISSELL.com
2
Page 3
Th for buying a BISSELL dp cleer
We’re glad you purchased a BISSELL
deep cleaner. Everything we know
about floor care went into the design
and construction of this complete,
high-tech home cleaning system.
Your BISSELL deep cleaner is well
made, and we back it with a limited
five-year guarantee. We also stand
behind it with a knowledgeable,
dedicated Consumer Care
department, so, should you ever
have a problem, you’ll receive fast,
considerate assistance.
My great-grandfather invented
the floor sweeper in 1876. Today,
BISSELL is a global leader in the
design, manufacture, and service
of high quality homecare products
like your BISSELL deep cleaner.
Thanks again, from all of us
at BISSELL.
Mark J. Bissell
Chairman & CEO
Safety Instructions...........2
Product View ................4
Assembly ...................5
Operations ................6-11
Maintenance & Care ......12-14
Troubleshooting ............15
Guarantee..................16
Consumer Care.............16
» Deep cleaning stairs and
high-trac areas on a
Tips
regular basis helps prolong
carpet life.
» Deep cleaning carpeting
regularly can reduce dust
and allergens in your home.
WARNING
GUIDE
WEEE
AN ACTION OR ATTENTION IS NEEDED TO THIS AREA IN ORDER
TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE, OR INJURY
READ USER GUIDE FOR COMPLETE SAFETY AND USER
INSTRUCTIONS
DO NOT THROW THE APPLIANCE AWAY WITH THE NORMAL
HOUSEHOLD WASTE AT THE END OF ITS LIFE, BUT HAND IT IN AT
AN OFFICIAL COLLECTION POINT FOR RECYCLING. BY DOING
THIS YOU WILL HELP TO PRESERVE THE ENVIRONMENT.
www.BISSELL.com
3
Page 4
Product View
1
2
3
4
2
5
6
7
10
8
9
11
12
13
14
15
16
1817
1 Spray Trigger
2 Cleaning Tools
3 Upper Handle
4 Power Cord
5 Carry Handle
6 Ready Tools™ Dial
www.BISSELL.com
4
(tools vary by model)
7 Removable Nozzle
8 DirtLifter
9 EdgeSweep™ Brushes
10 Belt Access Door
11 Cord Clip
12 Quick Release™ Cord Wrap
™
PowerBrush
(underside of machine)
13 Hose
14 Tank Carry Handle
15 Tank Latch
16 2-in-1 Water Tank
17 Power Pedal (red pedal)
18 Recline Pedal
Page 5
Asmbly
Your deep cleaner comes in four
easy-to-assemble components:
Upper Handle with Screws
Lower Base
Upper Hose/Cord Rack
Lower Hose/Cord Rack
The only tool you will need to assemble your
cleaner is a Phillips head screwdriver.
1. Slide upper handle onto lower base and secure
with two long screws into marked holes (screws
will be taped to upper handle).
2. Attach upper hose/cord rack to back of
the handle by guiding hook up into the slot
location and pressing firmly upward until it
is seated flush with back of machine. Secure
1 short screw through hole in the bottom of
upper hose/cord rack.
3. Attach lower hose/cord rack by guiding the
hook up into slot location and pressing firmly
upward until it is seated flush with back of
machine. Secure 2 short screws through holes
on sides of the bottom hose/cord rack.
4. Wrap hose around lower and upper hose/cord
racks and secure it by inserting trigger on hose
grip into opening on hose grip holder located on
upper hose/cord rack.
NOTE: Make sure to wrap hose beginning
from back of bottom hose/cord rack and
then wrapping over and around top of upper
hose/cord rack.
5. Wrap cord around lower and upper hose/cord
racks and secure plug to cord with clip on plug.
6. Attach cleaning tools as necessary to storage
locations on front of cleaner, bottom hose/cord
warp and end of hose grip.
Deep cleaner assembly is now complete.
WARNING
Do not plug in your deep cleaner until you have completely
assembled it per the instructions and are familiar with all
instructions and operating procedures.
1.
2. 3.
4.
www.BISSELL.com
5
Page 6
Operatis
Cleaning Fluid
Keep plenty of genuine BISSELL 2X formula on
hand so you can clean and protect whenever
it fits your schedule. Always use genuine
BISSELL deep cleaning formulas. Non-BISSELL
cleaning solutions may harm the machine and
may void the guarantee.
WARNING
To reduce the risk of fire and electric shock due to internal
component damage, use only BISSELL cleaning fluids
intended for use with the deep cleaner.
1.5 L 2X Wash & Protect PRO
Professional Stain & Odour
Formula w/ Scotchgard Protector
1.5L 2X Wash & Remove OXY
Deep Clean + Oxy Formula
#1265E
#1089E
650 mL Stain
Pretreat
#1147E
1.5 L 2X Wash & Protect PET
1.5 L 2X Wash & Refresh Blossom
& Breeze Fragrance Formula w/
Febreze® Freshness
Pet Stain & Odour Formula
w/ Scotchgard™Protector
#1078E
#1087E
650 mL Pet Stain
Pretreat
#1137E
1.5 L 2X Wash & Refresh
Cotton Fresh Formula w/
Febreze® Freshness
#1079E
1.5 L 2X Wash & Protect
Stain & Odour Formula w/
Scotchgard Protector
#1086E
1.5L 2X Wash & Refresh
Natural Orange Formula
#1146E
www.BISSELL.com
6
Page 7
Operatis
1
2
3
4
5
6
7
8
9
Special features
Heatwave Technology™
This deep cleaner features Heatwave Technology
that helps to maintain the temperature of the
hand hot tap water you put in it to provide
constant heat as you clean. The Heatwave
Technology automatically turns on when you
turn the machine on.
Before you clean
1. Plan activities to give your carpet time to dry.
2. Move furniture to another area if cleaning an
entire room (optional).
3. Vacuum area with a dry vacuum cleaner
before deep cleaning.
4. Plan your cleaning route to leave an exit path.
It is best to begin cleaning in the corner farthest
from your exit.
5. Pretreating (optional)
Pretreating is recommended to improve cleaning
effectiveness for heavily soiled carpet in high
traffic areas such as entry ways and hallways.
To pretreat:
a. Using BISSELL Stain Pretreat (sold
separately), generously spray evenly over
soiled area, do not overwet.
b. Wait 3-5 minutes before deep cleaning.
c. Clean as normal using your BISSELL deep
cleaner, following instructions in this guide.
WARNING
To reduce the risk of fire, use only BISSELL deep cleaning
formula for full size machines in your deep cleaner. Use
of cleaning formulas that contain lemon or pine oil may
damage this appliance and void the guarantee. Chemical
spot cleaners or solvent-based soil removers should not be
used. These products may react with the plastic materials
used in your deep cleaner causing cracking or pitting.
5a.
www.BISSELL.com
7
Page 8
Operatis
Filling the 2-in-1 water tank
1. Remove tank from base of machine by lifting
tank carry handle. Carry like a bucket to the sink.
2. Pull upward on bottom edge of latch in the
back of tank to unhook and remove lid.
3. Pull up on bladder fill cover that says
“Fill Here”. Fill the bladder with hand hot
(60°C/140°F MAX) tap water. Do not boil or
microwave water as it can destroy the bladder.
4. Using measuring cup provided, fill to indicated
fill line on measuring cup and pour in to bladder.
NOTE: Always use genuine BISSELL 2X
formulas to maximize cleaning and for the
safety of your machine.
5. Replace tank lid by seating front edge of tank
before back, then lock latch in place.
NOTE: Remember to secure lid and test to
make sure it is secure before picking up tank.
6. Place tank into machine base, seating
firmly in place.
WARNING
To reduce the risk of fire and electric shock due to internal
component damage, use only BISSELL cleaning fluids
intended for use with the deep cleaner. Non-BISSELL
cleaning solutions may harm the machine and may void
the guarantee.
1.
3.
6.
2.
5.
Carpet cleaning
1. Plug into a proper outlet. Set ReadyTools dial
to Floor Cleaning setting. Turn power on by
pressing red power pedal
with your foot.
2. With your foot, press gray recline pedal located
on back of machine next to red power pedal.
3. While pressing spray trigger, make one slow
forward wet pass and another back. Caution:
do not overwet.
4. Release spray trigger and make one slow
forward and backward pass over same area.
5. Repeat cleaning passes until solution being
suctioned up appears clean. Continue passes
without pressing spray trigger until you can’t
see any more water being suctioned up.
Repeated passes will help aid in dry time.
NOTE: You may notice hair and debris deposits
on the carpet or in the tank that were loosened
by the cleaning action. This debris should be
picked up and thrown away.
on back of machine
CAUTION
Take care not to run over loose objects or edges of
area rugs. Stalling the brush may result in premature
belt failure.
ATTENTION
Some Berber carpets have a tendency to fuzz with wear.
Repeated strokes in the same area with an ordinary
vacuum or deep cleaner may aggravate this condition.
Power Pedal
Recline Pedal
www.BISSELL.com
8
Page 9
Operatis
Adsdfdd ghg bvh
cvbbj jkn hnbj jkvh
gcghhjj jhffhl kllgh
Empty the 2-in-1 water tank/
clean removable nozzle
1. Press power pedal off. Remove 2-in-1 water
tank from base using tank carry handle. Carry
tank like a bucket to a utility sink or outside
where you will dispose of dirty water.
2. Pull upward on bottom edge of latch in the
back of tank to unhook and remove lid.
3. Empty dirty water from back corner of tank.
4. After each use, remove any debris trapped
in red lint screen on base of machine while tank
is still removed.
5. After each use, remove nozzle by grasping
each side of top of nozzle and pulling forward.
Clean nozzle by rinsing under running water.
6. When finished, replace nozzle by slightly
raising front of machine to line up slots on
each side of the base with hooks on each side
of nozzle. Attach at base first and then push
forward to click nozzle into place.
NOTE: If nozzle is not attached properly, loss
of suction will occur.
7. To continue carpet cleaning, refer back to
“Carpet cleaning” instructions on page 8.
If cleaning is complete, refer to “Maintenance
and care” section starting on page 12.
WARNING
To reduce the risk of electric shock, push power button
o and disconnect plug from electrical outlet before
performing maintenance or troubleshooting checks.
1.
Lint Screen
4.
6.
3.
5.
Ready Tools™
Your deep cleaner comes equipped with a hose
and at least one cleaning tool for cleaning stairs,
upholstery, and more.
Important! If using to clean upholstery,
check upholstery tags.
1. Check manufacturer’s tag before cleaning.
“W” or “WS” on the tag means you can use
your deep cleaner. If tag is coded with “X” or
“S” (with a diagonal strike through), or says
“Dry Clean Only,” do not proceed with any deep
cleaning machine. Do not use on velvet or silk.
If manufacturer’s tag is missing or not coded,
check with your furniture dealer.
2. Check for colourfastness in an inconspicuous
place.
3. If possible, check upholstery stuffing. Coloured
stuffing may bleed through fabric when wet.
4. Plan activities to give upholstery time to dry.
5. Vacuum thoroughly to pick up loose debris
and pet hair. Use a vacuum with a brush
attachment and a crevice tool to clean in fabric
folds and tufts.
IMPORTANT
Check for colourfastness in an inconspicuous place. If
possible, check upholstery stung. Coloured stung
may bleed through fabric when it becomes wet.
Manufacturer’s tag
www.BISSELL.com
9
Page 10
Operatis
6. To begin cleaning with attachments, follow
instructions on page 8 for filling 2-in-1 water tank.
7. Set ReadyTools dial to TOOLS setting. This
will allow spray and suction from hose.
8. Attach cleaning tool of your choice to end
of hose. If using a Pet Stain tool or 3-in-1
Upholstery and Stair tool, follow directions
below.
9. Hold tool approximately 2.5 cm above soiled
surface. Press spray trigger to apply cleaning
solution to soiled area. Using brush on tool,
gently scrub area to be cleaned. Release spray
trigger, apply downward pressure on tool
and pull it toward you to suction up dirt and
cleaning solution. Continue until no more dirt
can be removed. Caution: Do Not Overwet.
10. When finished cleaning, remove and rinse
tool(s) in clean, running water.
11. It is recommended that you suction clean
water from the tap to rinse out the hose. Be
careful not to over-fill your tank.
12. Before wrapping hose onto rack, lift end
of hose and stretch out to ensure all water is
cleared from hose.
13. Wrap hose around rack.
14. Empty 2-in-1 water tank and rinse out,
following instructions on page 9.
15.
If ReadyTools dial becomes difficult to turn,
the diverter assembly that holds dial may need
to be cleaned. To clean, first remove nozzle and
locate screw that holds diverter assembly in
place. With a Phillips screwdriver, remove the
screw and set aside.
16. Remove diverter assembly; hold under
running water making sure water flows through
and around dial. Turn dial about 10 times
clockwise and 10 more times counter clockwise.
This should free up any debris.
17. Wipe diverter assembly with a soft cloth and
replace back on machine. Replace nozzle.
18. Return ReadyTools dial to FLOOR CLEANING
setting.
7.
11. 12.
15. 16.
www.BISSELL.com
10
Page 11
Operatis
Cleaning with Pet Stain Tool
1. Set tool on soiled surfaces and press spray
trigger to spray solution onto soiled area to
be cleaned.
2. Slowly move tool back and forth over soiled
surface, keeping tool in contact with carpet.
3. Release spray trigger and move tool slowly
over soiled area to suction up water and dirt.
4. Continue to clean the area, working in small
sections, until no more dirt can be removed.
5. The front nozzle of the Pet Stain Tool can be
removed for easy cleaning. Push the button at the
top of the cleaning tool and slide the front nozzle
off the top of the cleaning tool. Rinse the front
nozzle and the tool with clean water and replace
front nozzle back onto the tool.
Cleaning with 3-in-1 Stair & Upholstery Tool
This versatile 3-way tool sprays, scrubs, and
suctions up dirt and stains from upholstery and
the outer curves, corner, and tread of carpeted
stairs.
1. Attach the tool to the end of the hose. (You
will hear a click when it is properly attached.)
2. Press the power button to turn on the cleaner.
3. Twist the tool head to desired setting to clean
carpeted stairs. The downward facing edge is
the active cleaning mode.
a. Use the flat area to clean top of stairs
b. Use indented area to clean outer corner
(nose) of stairs
c. Use pointed edge to clean inside crevice
4. Ensure the tool spray tip is pointing
downward. Pressing the spray trigger, slowly
move the tool back and forth over the soiled
surface keeping the tool in contact with the
carpet.
5. Release spray trigger and move tool slowly
over the soiled area to suction up water and dirt.
6. Continue to clean the area until no more
dirt can be removed.
7. After use, tool can be easily cleaned by
removing the front faceplate. Rinse out tool
before storing.
a.
1 2 3
FLAT
1.
3.
5.
1.
b. c.
NOSE
7.
CREVICE
www.BISSELL.com
11
Page 12
Mainnce & Care
Machine care
For best results, a few simple steps can assure
your machine is well maintained after cleaning is
complete.
1. Flush your machine of any remaining residual
solution.
a. Fill 2-in-1 water tank with clean hand hot
(60°C/140°F MAX) tap water.
b. Recline handle and press spray trigger
for 15 seconds while making forward and
backward passes on the carpet. Release
spray trigger and make forward and
backward passes for another 15 seconds or
until there is no more water being suctioned
up from carpet.
2. Press power pedal
wrap power cord.
3. After emptying 2-in-1 water tank, rinse it with
running hand hot (60°C/140°F MAX) tap water,
taking care to clean underneath and around
heavy duty bladder. Clean out red lint screen
prior to replacing tank. Removable nozzle may
be rinsed if necessary.
4. Replace 2-in-1 water tank on machine.
5. Any loose hair or debris can be pulled from
brush roll and thrown away. See instructions on
page 13 on removing brush roll.
6. Clean the ReadyTools dial assembly area by
following the instructions in Step 15 and 16 on
page 10.
7. To clean attachments, remove from hose and
rinse under clean, running water. Dry before
storing. Clean hose by suctioning clean water
from tap (taking care not to let tank overflow).
Before wrapping back on machine, lift end
of hose and stretch out to ensure all water is
cleared from hose. Refer to page 10, illustrations
11 and 12.
8. Wipe machine’s exterior with a soft cloth.
9. After carpet is dry, you may wish to vacuum
again to remove any leftover hair and fuzz the
deep cleaner may have brought to the carpet
surface.
off. Unplug machine and
WARNING
To reduce the risk of electric shock, push power button
o and disconnect plug from electrical outlet before
performing maintenance or troubleshooting checks.
Tip
» Let all parts
dry completely
before storing
www.BISSELL.com
12
Page 13
Mainnce & Care
Machine storage
Put unit away in a closet or basement for next
use. Store cleaner in a protected, dry area. Since
this product uses water, it must not be stored
where there is a danger of freezing. Freezing will
damage internal components and void guarantee.
WARNING
To reduce the risk of electric shock, push power button
o and disconnect plug from electrical outlet before
performing maintenance or troubleshooting checks.
Brush belt and brush removal & replacement
Occasional replacement of the brush belt or
brush may become necessary. If needed, please
follow instructions below.
1. Turn off machine and unplug it from outlet.
Wrap hose and cord on racks.
2. Remove 2-in-1 water tank and set aside.
3. IMPORTANT: Fully recline handle and turn
unit upside down.
4. Locate guard wire and remove screw.
NOTE: Guard wire does not remove.
5. Locate red belt access door and remove
two screws.
NOTE: The dark screw is a long machine screw
and will take approximately 25 full turns to
completely remove. The head of the screw will
lift from the belt access door so that it can be
easily removed.
6. Remove belt access door assembly from end
of brush and set aside.
7. Remove brush belt. If worn or damaged,
replace with new brush belt.
8. If necessary, the brush roll can be removed for
cleaning or replacement. To remove, rotate the
brush out of brush housing and pull brush off axle
attached to remaining end cap. The remaining
pivot arm can be removed by removing the screw
(this will allow for full access to brush chamber
for cleaning). Make sure “keyed” end of metal rod
is aligned with slot in pivot arm before re-assembling. Replace brush on axle, cogged-side, last.
You may need to rotate brush to allow it to slide
all the way down the axle.
9. Reattach brush belt by installing onto toothed
pump pulley and then onto toothed end of
brush.
10. Reattach belt access door assembly to end
of brush and rotate back into place. Replace
screws.
11. Replace screw on guard wire.
NOTE: Do not over tighten screws.
If you have any questions or are having trouble
removing, replacing or reinstalling your brush belt
or brush, please call BISSELL Consumer Care.
2.
4.
6.
3.
5.
7.
www.BISSELL.com
13
Page 14
Mainnce & Care
7
7
7
7
Pump belt removal & replacement
Occasional replacement of the pump belt may
become necessary. If needed, please follow
instructions below.
1. Turn off machine and unplug it from outlet.
Wrap hose and cord on racks.
2. Remove 2-in-1 water tanks and set aside.
3. IMPORTANT: Fully recline handle and turn
unit upside down.
4. Locate guard wire and remove screw.
NOTE: Guard wire does not remove.
5. Locate red belt access door and remove
two screws.
NOTE: The dark screw is a long machine screw
and will take approximately 25 full turns to
completely remove. The head of the screw will
lift from the belt access door so that it can be
easily removed.
6. Remove belt access door assembly from end
of brush and set aside.
7. Remove brush belt from end of brush and set
aside. If worn or damaged, replace with new
brush belt.
8. Remove pump belt and replace it with a new
belt by pinching belt at one end to make a large
loop. Attach belt to silver motor shaft first and
then pull towards larger, red pulley. Attach belt
to red pulley.
NOTE: Spinning the red pulley a few times will
help center belt and ensure correct assembly.
9. Reattach brush belt by installing onto
toothed pump pulley and then onto toothed
end of brush.
10. Reattach belt access door assembly
to end of brush and rotate back into place.
Replace screws.
11. Replace screw on guard wire.
NOTE: Do not over tighten screws.
If you have any questions or are having trouble
removing, replacing or reinstalling your brush
belt, please call BISSELL Consumer Care.
WARNING
To reduce the risk of electric shock, push power button
o and disconnect plug from electrical outlet before
performing maintenance or troubleshooting checks.
2. 3.
4.
6.
8.
5.
7.
9.
10.
www.BISSELL.com
14
Page 15
Trbleshting
WARNING
To reduce the risk of electric shock, push power button
o and disconnect plug from electrical outlet before
performing maintenance or troubleshooting checks.
Problem Possible causes Remedies
Reduced
spray OR
no spray
Bladder may be empty.
2-in-1 tank may not be seated
properly.
Pump may have lost prime.
Pump belt may be broken.
Press power pedal
bladder with clean hand hot
(60°F/140°C MAX) tap water and
formula.
Press power pedal
tank and reseat tank.
Press power pedal
ute turn on and depress spray trigger.
Press power pedal
from outlet. Follow belt replacement
instructions on page 14.
off; refill
off; remove
off; after 1 min-
off and unplug
DirtLifter
PowerBrush
does not turn
Cleaner
not picking
up solution
Please do
not return
this product
to the store.
Brush belt or pump belt is
off or broken.
ReadyTools dial may be on wrong
setting for cleaning job.
Poor tool position. (Hand held
attachments only).
Removable nozzle may not be
properly attached.
2-in-1 tank lid is not properly installed.
2-in-1 tank is not properly seated.
2-in-1 tank has picked up
maximum dirty water.
The lint screen may be clogged. Clean out lint screen, refer to page 9.
Other maintenance or service not included in the manual should
be performed by an authorized service representative.
Thank you for selecting a BISSELL product.
Press power pedal
from outlet. Follow belt replacement
instructions on pages 13 and 14.
Set ReadyTools dial to either floor
cleaning or tools.
Adjust angle; apply more downward
pressure.
Make sure nozzle is on correctly by
slightly raising front of machine to
line up slots on each side of base of
machine with hooks on each side of
nozzle. Attach at base first and then
click nozzle into place. Refer to image
6 on page 9.
Re-install lid; refer to images on page 9.
2-in-1 tank must be firmly seated to
function; remove and reseat 2-in-1 tank.
Empty 2-in-1 tank and refill, refer to
the Operation section.
off and unplug
www.BISSELL.com
15
Page 16
Csumer Guare
This Guarantee only applies outside of the USA and Canada. It is
provided by BISSELL International Trading Company BV (“BISSELL”).
This Guarantee is provided by BISSELL. It gives you specific rights.
It is offered as an additional benefit to your rights under law. You
also have other rights under law which may vary from country
to country. You can find out about your legal rights and remedies
by contacting your local consumer advice service. Nothing in this
Guarantee will replace or lessen any of your legal rights or remedies.
If you need additional instruction regarding this Guarantee or have
questions regarding what it may cover, please contact BISSELL
Consumer Care or contact your local distributor.
This Guarantee is given to the original purchaser of the product from
new and is not transferable. You must be able to evidence the date
of purchase in order to claim under this Guarantee.
Limited Five-Year Guarantee
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below,
BISSELL will for five years from the date of purchase by the
original purchaser repair or replace (with new or remanufactured
components or products), at BISSELL’s option, free of charge, any
defective or malfunctioning part or product.
BISSELL recommends that the original packaging and evidence of
the date of purchase be kept for the duration of the Guarantee
period in case the need arises within the period to claim on the
Guarantee. Keeping the original packaging will assist with any
necessary re-packaging and transportation but is not a condition
of the Guarantee.
If for your product is replaced by BISSELL under this Guarantee,
the new item will benefit from the remainder of the term of this
Guarantee (calculated from the date of the original purchase).
The period of this Guarantee shall not be extended whether or
not your product is repaired or replaced.
*EXCEPTIONS AND EXCLUSIONS FROM
THE TERMS OF THE GUARANTEE
This Guarantee applies to products used for personal domestic use and
not commercial or hire purposes. Consumable components such as
filters, belts and mop pads, which must be replaced or serviced by the
user from time to time, are not covered by this Guarantee.
This Guarantee does not apply to any defect arising from fair wear
and tear. Damage or malfunction caused by the user or any third
party whether as a result of accident, negligence, abuse, neglect, or
any other use not in accordance with the User Guide is not covered
by this Guarantee.
An unauthorised repair (or attempted repair) will void this Guarantee
whether or not damage has been caused by that repair/attempt.
Removing or tampering with the Product Rating Label on the
product or rendering it illegible will void this Guarantee.
SAVE AS SET OUT BELOW BISSELL AND ITS DISTRIBUTORS ARE NOT
LIABLE FOR ANY LOSS OR DAMAGE THAT IS NOT FORESEEABLE
OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY
NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT INCLUDING
WITHOUT LIMITATION LOSS OF PROFIT, LOSS OF BUSINESS, BUSINESS
INTERRUPTION, LOSS OF OPPORTUNITY, DISTRESS, INCONVENIENCE OR
DISAPPOINTMENT. SAVE AS SET OUT BELOW BISSELL’S LIABILITY WILL
NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
BISSELL DOES NOT EXCLUDE OR LIMIT IN ANY WAY ITS LIABILITY FOR
(A) DEATH OR PERSONAL INJURY CAUSED BY OUR NEGLIGENCE OR THE
NEGLIGENCE OF OUR EMPLOYEES, AGENTS OR SUBCONTRACTORS; (B)
FRAUD OR FRAUDULENT MISREPRESENTATION; (C) OR FOR ANY OTHER
MATTER WHICH CANNOT BE EXCLUDED OR LIMITED UNDER LAW.
Csumer Care
If your BISSELL product should require
service or to claim under our Limited
Five-Year Guarantee, please contact us
as follows:
Website:
www.BISSELL.com
Email:
UKSupport@bissell.com
Telephone:
0344-888-6644
Write:
BISSELL Homecare (Overseas) Inc.
Ground Floor
226 Berwick Avenue
Slough, Berkshire, SL1 4QT
United Kingdom
Spares are available for purchase.
To purchase visit www.4bissell.co.uk
Visit the BISSELL website: www.BISSELL.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: _____________ Please record your Purchase Date: _____________
NOTE: Please keep your original sales receipt. It provides proof of the date
of purchase in the event of a Guarantee claim. See Guarantee for details.
16
©2016 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 161-0136 08/16 RevA
Visit our website at: www.BISSELL.com
Scotchgard is a trademark of 3M.
Febreze is a trademark of The Proctor &
Gamble Company, Cincinnati, Ohio used
under license by BISSELL Homecare, Inc.
Loading...