Bissell 1699, 8905 User Manual

Safety Instructions

Product view / Accessories

Assembly

Features / Operations

ProHeat

™

ClearView

®

USER’S GUIDE

1699 SERIES - 120V
8905 SERIES - 120V

3

4

5

6-17

Routine Maintenance

18-20

Troubleshooting

21-22

Warranty

24

Replacement Parts

23

Consumer Services

22

Thanks for buying a BISSELL ProHeat™ClearView

®

We’re glad you purchased a BISSELL ProHeat ClearView heated
formula deep cleaner. Everything we know about floor care went into the
design and construction of this complete, high-tech home cleaning system.

Your ProHeat ClearView is well made, and we back it with a limited
one-year warranty. We also stand behind it with a knowledgeable,
dedicated Consumer Services department, so, should you ever have a
problem, you’ll receive fast, considerate assistance.

My great-grandfather invented the floor sweeper in 1876. Today,
BISSELL is a global leader in the design, manufacture, and service of high
quality homecare products like your ProHeat Clearview.

Thanks again, from all of us at BISSELL.

Mark J. Bissell

President and Chief Executive Officer

2

3

IMPORTANT SAFETY INSTRUCTIONS

■

Do not unplug by pulling on the cord.

■

Use only manufacturer’s recommended
attachments

■

Use only cleaning products formulated by
BISSELL for use in this appliance

■

Keep openings free of dust, lint, hair, etc.

■

Do not point attachment nozzle at people
or animals.

■

Keep appliance on a level surface

■

Turn off all controls before unplugging

■

Unplug before attaching the Turbo Brush

™

■

Be extra careful when cleaning stairs

■

Close attention is necessary when used by

or near children

SAVE THESE INSTRUCTIONS.

THIS MODEL IS FOR HOUSEHOLD USE ONLY.
Commercial use of this unit voids the
manufacturer’s warranty.

GROUNDING INSTRUCTIONS

This appliance must be connected to a grounded
wiring system. If it should malfunction or break
down, grounding provides a safe path of least
resistance for electrical current, reducing the risk
of electrical shock. The cord for this appliance
has an equipment-grounding conductor and a
grounding plug. It must only be plugged into an
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.

WARNING: Improper connection

of the equipment-grounding conductor can
result in a risk of electrical shock. Check
with a qualified electrician or service person
if you aren’t sure if the outlet is properly
grounded. DO NOT MODIFY THE PLUG. If
it will not fit the outlet, have a proper
outlet installed by a qualified electrician.
This appliance is designed for use on a
nominal 120-volt circuit, and has a
grounding attachment plug that looks like
the plug in the drawing above. Make cer­tain that the appliance is connected to an
outlet having the same configuration as
the plug. No plug adapter should be used

When using an electrical

appliance, basic
precautions should be observed, including
the following:

Read all instructions before using your
PROHEAT™CLEARVIEW.

™

WARNING:To reduce the risk of

fire, electric shock, or injury:

■

Do not immerse.

■

Use only on surfaces moistened by
cleaning process.

■

Always connect to a properly grounded outlet.

■

See Grounding Instructions.

■

Unplug from outlet when not in use and before
conducting maintenance or troubleshooting.

■

Do not leave machine when it is plugged in

■

Do not service machine when it is plugged in

■

Do not use with damaged cord or plug

■

If appliance is not working as it should, has
been dropped, damaged, left outdoors, or
dropped into water, have it repaired at an
Authorized Service Center.

■

Do not expose to rain, store indoors

■

Do not pull or carry by cord, use cord as a
handle, close door on cord, pull cord around
sharp corners or edges, run appliance over cord,
or expose cord to heated surfaces

■

Do not carry the appliance while in use

■

Unplug by grasping the plug, not the cord

■

Do not handle plug or appliance with wet hands

■

Do not put any object into appliance openings,

use with blocked opening, or restrict air flow

■

Do not expose hair, loose clothing, fingers
or body parts to openings or moving parts

■

Do not pick up hot or burning objects

■

Do not pick up flammable or combustible

materials (lighter fluid, gasoline, kerosene, etc.) or
use in the presence of explosive liquids or vapor

■

Do not use appliance in an enclosed space filled

with vapors given off by oil base paint, paint
thinner, some moth proofing sub stances, flam­mable dust, or other explosive or toxic vapors

■

Do not pick up toxic material (chlorine bleach,

ammonia, drain cleaner, gasoline, etc.)

■

Do not modify the 3-prong grounded plug

■

Do not allow to be used as a toy

■

Do not use for any purpose other than

described in this User’s Guide

■

Do not operate the appliance unless the
belt door is securely assembled in the
location provided

Grounded

Outlets

Grounding Pin

4

SmartMix

®

Tank

DirtLifter

®

PowerBrush

Floor Nozzle Window

SmartTemp

™

Ready Light

ReadyTools

™

Dial

Lower
Handle

Belt Access Door

Flow Indicator
(Filter Inside)

SmartMix

®

Switch

Flex Hose

Power Cord
Quick Release

Tool Caddy

SmartTemp

™

Switch

Tank-in­Tank

™

Power
Switch

Trigger

Upper
Handle

4” Upholstery
Tool Storage

Handle
Release

Tough Stain
Brush Storage

Hex Nuts

Crevice Tool
Storage

1.

2.

3.

4.

5.

*All items may not be included with your model.

More tools are available. To order replacement parts or
tools please refer to page 23.

Bare Floor Attachment

(Available on select models only.)

Spraying Crevice Tool

(Available on select models only.)

16 oz. BISSELL
Fiber Cleansing
Formula

™

with

Scotchgard

™

Protection

16 oz.
Tough Stain
PreCleaner

™

16 oz.
Floor
Cleansing
Formula

™

Tough Stain Brush

TurboBrush

™

(Available on select
models only.)

PreTreat Wand

(Available on select
models only.)

BRUSH

SUCTION

T

R

I

A

L

S

I

Z

E

Floor Cleansing Formula
FOR DEEP
CLEANING MACHINES

™

32 FL.OZ.

(946 mL)

CAUTION:

MAY BE IRRITATING TO THE EYES.

READ BACK PANEL CAREFULLY

Safely Deep Cleans and
Revitalizes No-Wax Floors

D

I

R

T

A

N

D

S

T

A

I

N

S

R

E

M

O

V

E

S

D

E

E

P

D

O

W

N

®

T

O

U

G

H

S

T

A

I

N

P

R

E

C

L

E

A

N

E

R

™

P

e

n

e

t

r

a

t

e

s

a

n

d

L

o

o

s

e

n

s

T

o

u

g

h

S

t

a

i

n

s

&

E

m

b

e

d

d

e

d

D

i

r

t

b

e

f

o

r

e

D

e

e

p

C

l

e

a

n

i

n

g

Accessories

Keep plenty of genuine BISSELL Advanced
Cleaning Formulas on hand so you can clean
whenever it fits your schedule. Always use
genuine BISSELL deep cleaning formulas.
Non-BISSELL cleaning solutions may harm
the machine and void the warranty.

16 oz. BISSELL
Multi-Allergen
Formula

™

with

Scotchgard

™

Protection

4” Upholstery Tool

(Available on select
models only.)

TurboBrush

®

Storage
(Select Models)

5

How To Put It Together

How to Use this Guide

This User’s Guide has been designed to help you get
the utmost satisfaction from your BISSELL ProHeat
ClearView. You’ll find assembly and operating
instructions, safety precautions, as well as maintenance
and troubleshooting instructions. Please read this Guide
thoroughly before assembling your Deep Cleaner.

Pay particular attention to the product diagram, assem­bly instructions, and part names. Locate and organize all
parts before assembly. Familiarize yourself with the parts
and where they go. Following this User’s Guide will
greatly enhance your ability to get the most performance
from your BISSELL ProHeat ClearView for many years.

Your ProHeat ClearView comes in three,
easy to assemble components.
Upper Handle
Lower Handle
Tool Caddy

The only thing you will need to assemble your cleaner is
a Phillips head screwdriver.

Refer to Assembly Diagram on page 4

Slide Upper Handle onto Lower Handle.

Feed bundled power cord through Tool Caddy
from caddy’s flat side.

Align Upper Handle holes and Tool Caddy holes.

Place hex nut into back of Tool Caddy and hold in
place. Insert bolt from front to back turning into
the hex nut until snug. Do not over tighten.
Repeat for the second bolt and hex nut.

Insert 2 screws into lower 2 holes.Turn until snug.

Snap tools into Storage on the Tool Caddy as
shown in figure 6.

Wrap Power Cord and Flex Hose as shown in
figure 7.

ProHeat ClearView assembly is
now complete.

WARNING:

Do Not plug in your cleaner
until you have completely
assembled it per the following
instructions and are familiar
with all instructions and
operating procedures.

1.

2.

3.

4.

ON

O

F

F

O

N

OFF

6

7

5.

6.

7.

6

Special Features of Your BISSELL ProHeat™ClearView

®

The BISSELL SmartClean®System

The ProHeat ClearView is a home cleaning system that
automatically mixes hot tap water with the BISSELL
advanced cleaning formula and heats the solution as
it is applied to the carpet. The combination of heated
cleaning solution, powered brush and suction provide a
safe & effective method of cleaning.

Temperature control automatically heats the cleaning
solution as it is being applied to the carpet (*) to safely
optimize cleaning effectiveness.

The Power Switch controls power to the machine; both
switches must be ON for SmartTemp to work.

The SmartTemp Switch is found on the back of the handle
next to the Power Switch. You may choose not to use the
SmartTemp feature if you are cleaning delicate wool or
oriental rugs.

*SmartTemp heats the cleaning solution for carpet
and bare floor application only. It does not heat
solution sprayed through the accessory tools.

The SmartTemp Ready Light indicates when the heater
is ON. The heater should be turned on two minutes before
cleaning, to become fully warmed up and ready to clean.
The Smart Temp Ready Light is found on the front of the
handle where itis easy to see while you clean

SmartTemp increases the water temperature 25° and will
not allow it to exceed 180°.

Provides custom control for each cleaning job.

Lift the SmartMix concentrate bottle up and out of the
machine base.

Turn the bottle over so that the valve cap is in an upward
position. Unscrew the valve cap and fill the bottle to the
mark with BISSELL Deep Cleaning Formula.

Replace the valve cap turning until snug.

SmartTemp

®

1.

2.

3.

4.

SmartMix
bottle

SmartMix

®

1.

2.

3.

O

N

O

F

F

Power Switch

SmartTemp
Switch

SmartTemp Ready Light

ON

OFF

7

SmartMix Continued

Replace SmartMix concentrate bottle.

Note: If bottle leaks, check for proper

positioning of o-ring and straw.

Choose the SmartMix setting that fits the cleaning job.

Water Rinse - use for gentle cleaning or for the

final rinse after cleaning.

Normal- automatically provides the best mix of

water and concentrate for most cleaning jobs.

High Traffic- automatically mixes the right amount

of water and concentrate to dissolve tough grime

and heavy soil. Note: Residual cleaning materials left

in carpet from other products may cause excessive

foaming when picked up. If foam is overflowing

tank, move SmartMix dial to “Water Only” position

until the condition stops.

Note: Both the SmartMix Bottle and the clean

water tank must have liquid in them
in order for the machine to spray. If
one tank is empty, the machine will
temporarily lose its prime and not apply
either cleaning solution or water only.

Important:

If you are using the WATER RINSE
setting, fill the Smart Mix bottle with
water also!

The pow-

ered
brush roll at the floor nozzle is designed to enhance cleaning
performance. The bristle pattern lifts out the deep down dirt
while gently grooming carpet fibers. The floating suspension
self-adjusts to all carpet heights and protects your carpet if
you leave the power switch ON. When the machine handle is
in the fully upright position, CarpetSaver automatically raises
the brush off the carpet.

4.

5.

WARNING:

To reduce the risk of
injury, be extra careful
when cleaning stairs.
Make sure machine is
secure and level.

O-ring
Position

Tip:

Deep Cleaning
stairs and high
traffic areas on
a regular basis
can prolong
carpet life.

SmartMix
Dial

When filling bottle or
storing unit, set

dial to:

H

I

G

H

T

R

AF

F

I

C

W

AT

E

R

R

I

N

S

E

N

O

R

M

A

L

DirtLifter®PowerBrush

WARNING:

To reduce the risk of fire,
use only BISSELL Deep
Cleaning Formula in your
ProHeat ClearView. Use of
cleaning formulas which
contain lemon or pine oil
may damage this appli­ance and void warranty.
Chemical spot cleaners or
solvent based soil
removers should not be
used. These products may
react with the plastic
materials used in your
ProHeat ClearView, causing
cracking or pitting.

8

Tank-in-Tank

Our Tank-in-Tank system is designed with a Bladder inside for
clean water. As you clean, the Bladder will empty. Dirty water
collects in the tank outside the Bladder.

Step on handle release to lay the machine handle
down out of the way.

Lift the Tank-in-Tank handle. The handle locks the
lid in place.

Carry it like a bucket to fill at the sink.

Note: You may notice hair and debris deposits on

the carpet that were loosened by the
brushing action (especially with newer
carpets that have never been deep cleaned
before). This debris should be picked up
and thrown away. Debris that deposits in
the Brush Belt should be cleaned between
uses to keep the Belts running free.

Set the tank down and rotate the handle forward to unlatch
the lid. Lift off and set the lid aside.

Find the mouth of the Bladder and fill to the bottom of the
neck with clean hot tap water. *Do not boil or microwave

water as it can destroy the Bladder.

Note: Fill the Bladder with clean hot tap water only.

Replace the Tank Lid matching the lid and tank edges. Handle
must be in the forward position to reinstall.

Rotate the handle to the carrying position to re-latch
the lid.

Replace tank in machine base, seating firmly in place.

Rotate handle back down to the latched position.

Note: Both the SmartMix Bottle and the clean

water tank must have liquid in them in
order for the machine to spray. If one tank
is empty the machine will not apply either
cleaning solution or water.

Important: If you are using the WATER RINSE

setting, fill the SmartMix bottle with
water also!

1.

2.

3.

4.

5.

6.

7.

8.

9.

Lift and Carry

Fill Bladder only with
clean hot tap water

Rotate Handle to

Unlatch

Latched

3

4

5

9

9

When It’s Time to Empty Tank-in-Tank

1.

2.

3.

4.

5.

6.

7.

8.

9.

Tip:

Thorough
vacuuming
before deep
cleaning will
prevent early
clogging of
lint trap.

Tip:

A special red
float device
in the tank will
cause the cleaner
to stop removing
solution from the
carpet and the
motor sound will
rise in pitch to let
you know the
dirty water tank is
full.

Remove the Tank-in-Tank – follow steps 1 and 2
on page 8.

Carry the Tank-in-Tank, like a bucket, to the sink where you
will dispose of the dirty water.

Remove Tank Lid by rotating handle forward to unlatch lid and
lifting lid off tank.

Pour out dirty water.

After each use, remove and rinse the lint screen located on
the Tank Lid.

A. Remove Tank Assembly from unit.
B. Remove Tank Lid.
C. Remove any debris caught in Lint Screen.
D. Reinsert Lint Screen on Tank Lid. The screen will click

into place

E. Replace Tank Lid.
F. Reinsert Tank Assembly into unit.

Refill with clean tap water as above, steps 5 through 9 on
page 8, and refill the SmartMix bottle with BISSELL Deep
Cleaning Formula as necessary.

When the cleaning job is complete, rinse out the
Tank-in-Tank by rinsing clean water between the Bladder and
tank.

Return Tank-in-Tank to the machine, following steps 6 through
9 (on page 8).

Refer to the Maintenance section, page 18 for the
final cleanup.

3

5D

Rotate Handle to

Unlatch

Fill bladder
only with clean
hot tap water

5C

Lint Screen

Pour out

dirty water

4

6

3

Latched

8

10

The Flow Indicator

This is located on the machine base. It spins when the trigger
is pressed to indicate that the machine is applying cleaning
solution to the floor. It will stop spinning to indicate that the
SmartMix bottle or Bladder needs to be refilled, or when the
trigger is released. Flow Indicator does not spin when set to
Tool setting.

This provides above floor cleaning with the flip of a switch. Just
choose the cleaning tool, attach to the flex hose and ProHeat
Clearview is ready to clean upholstery, stairs or more.*

*Set the dial to Floor Cleaning when cleaning carpets
or bare floors or set it to Tools/PreTreat when using
the flex hose attachments or for pre-treating floors.
*SmartTemp heats the cleaning solution for carpet
and bare floor application only. It does not heat
solution sprayed through the accessory tools.

(Available on select models only)

Unplug cleaner from outlet before attaching TurboBrush.
Attach TurboBrush to the flex hose by pressing tool onto the
grip/trigger until button snaps into hole. Make certain tool is
securely in place.

Move the TurboBrush switch to the “BRUSH” position.
This activates the brush.

Place the tool directly on the soiled surface. Apply downward
pressure on the tool and pull towards you while pulling trigger
to spray cleaning solution.

Release the spray trigger and move the switch to the
“SUCTION” position. Vacuum the area until no more cleaning
solution can be removed.

Repeat steps 1-3 until no more dirt can be removed.

Caution: Do not overwet.

ReadyTools Dial

TurboBrush

®

1.

2.

3.

4.

Flow Indicator

Assembly

Use

ReadyTools
Dial

OLS

T

A

TO

E

ETR

PR

R

G

O

IN

N

FLO

LEA

C

SUCTION

BRUSH

11

Disconnect the TurboBrush from the flex hose by pushing
down on the button lock and pulling straight off.

Once removed from the Flex Hose, the TurboBrush can
be cleaned.

A Move the switch to the “SUCTION” position.

B Rinse under running water.

C Check spray nozzle for dirt. If necessary, clean with a soft

bristle brush.

D Replace TurboBrush in the special storage location on the

handle front. (on select models only)

Plan activities to give carpet time to dry.

Remove easily moved furniture from the room (chairs,
lamps, coffee tables, etc).

Vacuum thoroughly to pick up loose debris and pet hair

before using the ProHeat ClearView.

Plan your cleaning route to leave an exit path. It is best to
begin cleaning in the corner farthest from your exit.

Set up the machine following instructions in
The Features section, pages 6-11.

Use a BISSELL Advanced Cleaning Formula in the SmartMix
tank.When cleaning carpets, stairs or upholstery, use clean
water in the SmartMix Tank for gentle cleaning or rinsing.

Choose the SmartMix setting to match the cleaning job.

Set the ReadyTools switch to either Tools/PreTreat or Floor

Cleaning.

1.

2.

When You’re Done

Operations

1.

2.

3.

4.

Machine Preparation

1.

2.

3.

4.

B
RUS

H

SUC

T
I
O
N

1

START

HERE

——— 4'———

2

3

4

8

7

6

5

9

10

1

1

1

2

EX

I

T

—

—— —

—

—

3

'

Before You Clean Carpets

12

Pretreating is recommended to improve cleaning
effectiveness for heavily soiled carpet in high traffic
areas such as entryways and hallways:

Set the SmartMix dial to High Traffic.

Set ReadyTools dial to PreTreat.

Plug into a proper outlet and turn on both the Power and
Smart Temp Switches.

While pressing the trigger slowly make several passes over
the area to be cleaned. Caution Do not overwet.

Turn the machine Power Switch OFF and let the BISSELL
Advanced Cleaning Formula dissolve the tough soil for 1-2
minutes before continuing.

Plug into a proper outlet and turn the Power and the
SmartTemp switches ON. Wait two minutes for the heater to
warm up before beginning to clean.

While pressing the trigger, make one slow forward wet pass
and another one back. Let the SmartTemp heated formula
and DirtLifter Powerbrush do the work for you.Caution: Do

not overwet.

Note: Take care not to run over loose objects or edges of area

rugs. Stalling brush may result in premature belt failure.

Release the trigger and make one slow forward and back
pass over the same area to remove any residual dirty water.

Repeat cleaning passes until solution being pulled up
appears clean.

Continue passes without pressing the trigger until you can’t
see any more water being pulled up.

Note:

Both the SmartMix and the clean water tank must have liquid in
them in order for the machine to spray. If one tank is empty the
machine will not apply either cleaning solution or water only.

After cleaning, you may want to turn the SmartMix dial to
Water Only to give your carpeting a final rinse. This will
ensure thorough removal of embedded dirt loosened by the
Advanced Deep Cleaning Formula. Advanced Deep Cleaning
Formulas contains an anti-resoiling agent that helps your
carpets repel dirt and keeps them looking good longer.

When the cleaning job is complete refer to the Maintenance

section for machine cleanup and storage instructions on

page 18

1.

2.

3.

4.

5.

PreTreating

Tip:

Try pretreating
stairs or entry
ways with
BISSELL Tough
Stain PreCleaner.
Then deep
clean with the
SmartMix

®

dial set on
High Traffic.

Carpet Cleaning

1.

2.

3.

4.

5.

6.

7.

When filling bottle or
storing unit, set

dial to:

ATTENTION
BERBER CARPET
OWNERS:

Some Berber Carpets have a
tendency to fuzz with wear.
Repeated strokes in the
same area with an ordinary
vacuum or deep cleaner may
aggravate this condition.
Please see Stain Removal
instructions on page 13.

T

N

I

O

A

U

T

G

S

H

™

P

R

R

E

E

N

C

A

L

E

s

n

i

a

P

t

S

e

h

n

g

e

u

t

o

r

T

a

t

s

e

n

s

e

s

a

o

n

o

d

L

&

E

m

g

b

e

n

d

i

d

n

e

d

a

D

e

l

i

r

C

t

b

p

e

e

f

o

e

r

D

e

13

Stain Removal

Do Not Delay! Failure to attend to an accident soon after it occurs
may cause it to set and become permanent.

Before treating any stain, follow these pre-treatment steps:

Blot up liquids with an absorbent cloth or paper towels.
White materials are recommended because certain dyes
may bleed and make the stain worse.

Gently scrape up semi-solids with a spoon or spatula. Do
not use a knife or other utensil with sharp edges
because it could damage the carpet or upholstery.

If the area has dried, remove the remaining semi-solids
and residue with a sweeper or vacuum.

Be sure to pre-test any spot removal solutions or chemicals
on an inconspicuous area first. This is extremely
important; different dyes and materials could be damaged
or discolored by a cleaning solution. If such a change
should occur, try a different solution or call a professional. If
cleaning on Berber Carpet gently run your machine over
a hidden area. If no fuzzing occurs, continue cleaning in
soiled area.

Use one of the following methods to Preclean the stain:

Using BISSELL Tough Stain Precleaner

™

, generously
spray the area with the formula. Gently work the solution
with a clean cloth or towel into the area using light
strokes from the edges of the stain to the center. When
your cloth reaches the center of the stain, gently pinch it
in an upward motion. Make sure to turn and change your
cloth frequently and do not rub the stain. You may repeat
this process several times.

or

Use your BISSELL deep cleaner as a Precleaner. With
one of the tools attached to hose, set the Ready Tools
dial to Pretreat and the Smart Mix dial to the High Traffic
setting. Spray the area with solution and allow the Deep
Cleaning formula to penetrate for 3-5 minutes.

Once the Precleaning is complete, use the attached tool
to gently scrub the stain with back and forth strokes.

Allow to dry. Some difficult stains may require a second
treatment.

1.

2.

3.

4.

6.

5.

7.

14

1.

Check manufacturer’s tag before cleaning. “W” or “WS”
on the tag means you can use your ProHeat ClearView.
If the tag is coded with “X” or “S” (with a diagonal strike
through), or says “Dry Clean Only,” do not proceed. Do
not use on velvet or silk. If manufacturer’s tag is missing
or not coded, check with your furniture dealer.

Check for colorfastness in an inconspicuous place.

If possible, check upholstery stuffing. Colored stuffing
may bleed through fabric when wet.

Plan activities to give upholstery time to dry.

Vacuum thoroughly to pick up loose debris and pet hair.
Use a vacuum with a brush attachment and a crevice
tool to clean in fabric folds and tufts.

How to Clean Upholstery and Small Areas

Important - Check Upholstery Tags:

2.

3.

4.

5.

A

d

s

d

f

d

d

g

h

g

b

v

h

c

v

b

b

j

j

k

n

h

n

b

j

j

k

v

h

g

c

g

h

h

jj

jh

f

fh

l

k

ll

g

h

Manufacturer’s tag

15

Set up the machine following instructions in the Features
section, pages 6-11.

Use BISSELL Advanced Cleaning Formulas in SmartMix tank.

Set the ReadyTools dial to Tools or PreTreat.

* SmartTemp heats the cleaning solution for carpet

and bare floor application only. It does not heat
solution sprayed through the accessory tools.

Set SmartMix Dial to Normal.

Choose the 4” Small Area Tool, the Tough Stain Brush, or the
Spraying Crevice Tool and connect to the Flex Hose.

Plug into a proper outlet and turn Power Switch ON.

While pressing the trigger, slowly move the spraying tool
back and forth over the soiled surface. Release the trigger to
suction soiled water.

Continue to clean soiled area, working in small sections,
until no more dirt can be removed.

Caution: Do not overwet.

When the cleaning job is complete refer to the
Maintenance section for machine cleanup and storage
instructions on page 18.

1.

2.

3.

4.

1.

2.

3.

4.

5.

Machine Preparation

Cleaning Technique

Tip:

Deep cleaning
carpeting and
upholstery with
BISSELL Multi­Allergen Removal
Formula™ with
Scotchgard™
protection regu­larly can reduce
dust and aller­gens in
your home.

16

1.

2.

3.

4.

5.

1.

2.

3.

4.

5.

6.

Cleaning Bare Floors

The Bare Floor Tool is included in select models only.
If your ProHeat CleaView did not come so equipped,
you may contact BISSELL Consumer Services at
www.bissell.com or 1-800-237-761 to order one. The
Bare Floor Tool provides effective cleaning for linoleum,
vinyl, and tile floors.
Caution: Do not use on hardwood floors.

Use BISSELL Floor Cleansing Formula.

Vacuum or sweep thoroughly to pick up loose debris and pet hair.

Remove easily moved furniture from the room ( chairs, tables, etc.).

Plan your cleaning route to leave an exit path.

Plan activities to allow 30 minutes for the floor to dry completely.

Step on the handle release to lay the machine handle down.

Remove the Tank-in-Tank from the machine base.

Lift the machine base to expose the underside of the Floor Nozzle.

Attach Bare Floor Tool to Floor Nozzle with long Tab to the right
side (ReadyTools side) of the Floor Nozzle.

First attach left side (short Tab) catching tab over nozzle edge.

Gently bend long Tab (right side) outward to easily snap over
edge of clear nozzle on left.

Attach the Bare Floor Tool

Tilt Handle
Back

Handle Release

Carrying

Bare Floor
Cleaning Tool

Bottom Front Edge
of Floor Nozzle

Snap Together

17

Machine Preparation

Set up machine following instructions in the Features
section, pages 6-11. Be sure to thoroughly rinse out any
remaining Fiber Cleansing Formula from the SmartMix
bottle to prevent slippery linoleum, vinyl, and tile floors.

Use BISSELL Floor Cleansing Formula in
the SmartMix tank.

Check ReadyTools Dial - it should be set on Floor Cleaning.

Choose the SmartMix setting to match the cleaning job.

Plug into a proper outlet and turn Power Switch ON. Turn
SmartTemp switch ON. The SmartTemp Ready Light
illuminates and ProHeat ClearView is ready to clean.

Slowly move the machine nozzle with Bare Floor Tool
forward and back over soiled surface one time while
pressing the trigger. Caution: Do not overwet.

Repeat the motion without pressing the trigger using the
Bare Floor Tool to squeegee and suction up the dirty water.

Repeat steps 1 and 2 backing along the exit path.

Allow about 30 minutes for the floor to dry completely.

When the cleaning job is complete refer to the
Maintenance/Storage section on page 18.

To remove Bare Floor Tool gently bend long tab (right side)
outward and pull tool down away from nozzle. Rinse
thoroughly, dry and store.

1.

2.

3.

4.

1.

2.

3.

5.

6.

Cleaning Bare Floors Continued

Bare Floor Cleaning Technique

When filling bottle or
storing unit, set

dial to:

4.

18

Routine Maintenance

Turn Power and SmartTemp switches OFF.

Unplug power cord from the outlet and coil around Power
Cord Quick Release.

Remove and rinse tools in clean, running water, dry and
replace in the Tool Caddy.

Coil Flex Hose around storage brackets on Tool Caddy.

Remove Tank-In-Tank, dispose of dirty water. See Features
section, page 8-9.

Rinse out Tank-In-Tank and replace on the machine; Clean
out lint trap.

Clean out the Flow Indicator Filter each time it is used to
ensure best cleaning performance. Unscrew the Flow
Indicator Cap, lift out the Red Rotor and White Filter. Rinse all
three parts in tap water. Replace the filter and rotor. Replace
the Flow Indicator Cap; turn until snug, do not over-tighten.

Wipe all exterior surfaces with a soft cloth.

Store cleaner upright in a protected, dry area.

Note: ProHeat ClearView uses water and must not be

stored where there is a danger of freezing.
Freezing will damage internal components and
void the warranty.

When carpet is dry, vacuum again to remove hair and fuzz
the ProHeat ClearView may have loosened.

Tip:

SmartMix Bottle
may be stored
with concentrate
ready for your
next cleaning job.
Make sure dial is
turned to the
Water Rinse
Setting when
storing.

O

N

O

F

F

Cap

Rotor

Filter

WARNING:

To reduce the risk of fire,
electric shock or injury
unplug from outlet
before servicing.

When filling bottle or
storing unit, set

dial to:

7.

8.

9.

1.

2.

3.

4.

5.

6.

10.

Turn the machine off and unplug from the wall outlet.

Step on the release pedal and recline the handle down onto
floor (see illustration).

Remove Tank-In-Tank and SmartMix tanks. Set them aside
(see illustration).

Remove Belt Access Door located near the Floor Cleaning/
Tools switch by inserting a flat head screwdriver into the
slot nearest to the handle and gently prying the access door
off (see illustration).

Turn the machine onto its side so the belt access area is
facing upward (see illustration).

On the bottom of the machine, near the belt access area,
is a red retainer plate that holds the black brush arm and
brush in place. Using a Phillips head screwdriver remove the
screw that holds the red retainer plate in place. Set red
retainer plate and Phillips head screw aside (see illustration).

Remove the black brush arm that holds the brush in place.
Set the black brush arm aside (see illustration).

Remove the “toothed” brush belt from the brush then from
the red pump pulley. Set the “toothed” brush belt and brush
aside.

Locate and remove broken pump belt.

19

7.

8.

9.

7

8

9

To Remove Broken Pump Belt

Pump Belt Replacement

1.

2.

3.

4.

5.

6.

2

3b

5

6

3a

4

20

With the unit still on its side, loop one end of the replacement
pump belt around the red pump pulley and then the other end
around the silver motor shaft (see illustration). Do not twist the
replacement pump belt.

Re-install the toothed brush belt first onto the red pump pulley

and then onto the toothed end of the brush (see illustration).

Re-install the brush into the base of unit.

Place the black brush arm onto the brush and slide black
brush arm into base of unit. The black brush arm and brush
should slide easily into original position(see illustration).

Re-install the red retainer plate and Phillips head screw
(see illustration).

Using your finger, gently spin the replacement pump belt on
the silver motor shaft. If assembled correctly, the replacement
pump belt should rotate freely around the silver motor shaft
and drive pulley without obstruction. The brush should also
rotate freely when the silver motor shaft is turned.

Turn the machine right side up and replace the Tank-In-Tank,
SmartMix Tank and Belt Access Door (see illustration).)

Assembly is now complete.

If you have any questions, or are having trouble installing your
replacement pump belt, please call BISSELL Consumer
Services at 1-800-237-7691.

6

7a

7b

5

5.

6.

7.

8.

1

2

3

4

To Install the Replacement Pump Belt

1.

2.

3.

4.

21

Troubleshooting

SmartTemp Ready Light does not illuminate.

Possible Causes Remedies

The SmartTemp switch is not Turn on the SmartTemp switch.
turned ON.

The machine Power Switch is not Both switches must be ON to
turned ON. activate the SmartTemp Ready Light.

Reduced spray or no spray

Possible Causes Remedies

Bladder may be empty. Refill tank with hot tap water.

SmartMix bottle may be empty. Fill with BISSELL Deep Cleaning

Formula for cleaning or water if rinsing.

The filter may be clogged. Clean out Flow Indicator Filter, page 18.

Tanks may not be seated properly. Turn power OFF; remove & reseat tanks.

Pump may have lost prime. Turn power OFF; after 1 minute turn ON

and depress trigger.

The Pump Belt may be broken. Turn the machine OFF and unplug from

the outlet. To check if a Pump Belt has
broken, you will need a flat head
screwdriver. Insert the blade end into
the lower slot of the Belt Access door
to release the lower snap. If necessary,
insert the blade end into the upper slot
to release the upper snap. Examine the
belt for breakage. You should be able
to see the Pump Belt looped around
the motor shaft. If it is broken or
missing, please refer to Replacement
Parts on page 23 before calling
Consumer Services. Complete
installation instructions will
accompany the replacement belt.

DirtLifter PowerBrush does not turn.

Possible Causes Remedies

The Brush Belt or Pump Belt Turn the machine OFF and unplug from
may be broken. the outlet. To check if a Pump Belt has

broken, you will need a flat head
screwdriver. Insert the blade end into
the lower slot of the Belt Access door
to release the lower snap. If necessary,
insert the blade end into the upper slot
to release the upper snap. Examine the
belt for breakage. If broken refer to
pages 19-20.

WARNING:

To reduce the risk of
fire, electric shock or
injury unplug from outlet
before servicing.

Lift Here

Insert
Screwdriver
Blade Here

22

BISSELL Customer Service

Troubleshooting Continued

Cleaner not picking up solution.

Possible Causes Remedies

Ready Tools dial may be at the Set ReadyTools dial to either Tools or
wrong setting for the cleaning job. PreTreat or Floor Cleaning.

Nozzle Window may not be Press down firmly on the black oval
properly attached. gasket at the top window to make sure

the two tabs on the back of the Nozzle
Window are snapped into the mating
slots in the main housing.

Tank-in-Tank lid is not Re-install lid; refer to the Features
properly installed. section.

Tank-in-Tank is not properly seated. Tank-In-Tank must be firmly seated to

function; remove and reseat Tank-in-Tank.

Poor tool position. Adjust angle; apply more downward
(Hand held attachments only). pressure.

Tank-in-Tank has picked up Empty Tank-in-Tank, refer to
maximum dirty water. the Features section.

For information about repairs or replacement parts, or questions about
your warranty, call:

BISSELL Customer Service

1-800-263-2535

Monday - Friday 8 a.m. - 4:30 p.m. EST

Or write:

BISSELL Ltd.,
Box 1003
Niagara Falls, Ont.,
L2E 6W2
ATTN: Customer Service

Or visit the BISSELL Web Site - www.bissell.com
E-mail us at: [e-mail]

When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________

NOTE: Please keep your original sales receipt. It provides proof of date of

purchase in the event of a warranty claim. See "About Your Warranty"
on page 24 for details.

Please do not return this product to the store.

23

Replacement parts - BISSELL ProHeat ClearView

Item Part No. Part Name

1* 210-9201 4” Small Area Tool
2* 603-0910 6” Stair Tool
3* 210-9148 Spraying Crevice Tool
4* 210-1197 TurboBrush

®

5* 214-9131 Bare Floor Tool
6* 014-9142 PreTreat Wand
7* 215-9155 Tough Stain Brush
8 015-9043 Tank Assembly Complete

9 015-4439 Tank Lid Assembly
10 015-9041 Tank Bottom
11 210-1785 SmartMix

®

Bottle (Includes Cap)

12 210-1795 SmartMix

®

Cap Assembly
13 210-1651 Flow Indicator Cap
14 210-6214 Flow Indicator O-Ring
15 210-7635 Flow Indicator Rotor
16 210-3510 Flow Indicator Filter
17 214-9865 Floor Nozzle Window and Gasket

18 210-4052 Window Gasket
19 215-0628 Replacement Pump Belt

(With Instructions)

20 015-0621 Replacement Belt

(With Instructions)

21 213-3501 Lint Screen

*Not all parts are included with every model.

©2002 BISSELL HOMECARE, Inc.
BISSELL Ltd.,
Niagara Falls, Ont., L2E 6W2
All rights reserved. Printed in USA.
Part Number 010-5846

Visit our Web Site at:
www.bissell.com

Scotchgard is a trademark of 3M

1*

2*

3*

6*

or

BRUSH

SUCTION

4*

5*

9

7*

8

10

11

12

13

14

15

16

19

20

21

17

18

24

If you need additional instruction regarding this warranty or have questions regarding

what it may cover, please contact BISSELL Customer Service by e-mail, telephone, or
regular mail as described below.

Limited One Year Warranty

Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the
product BISSELL Ltd. will repair or replace (with new or remanufactured components
or products), at BISSELL’s option, free of charge from the date of purchase by the
original purchaser, for one year any defective or malfunctioning part.

See information below on "If your BISSELL product should require service".

This warranty applies to product used for personal, and not commercial or rental
service. This warranty does not apply to fans or routine maintenance components such
as filters, bags, belts, or brushes. Damage or malfunction caused by negligence,
abuse, or use not in accordance with the User's Guide is not covered.

If your BISSELL product should require service:

Call BISSELL Customer Service at the number below or www.bissell.com

to locate a BISSELL Authorized Service Centre in your area. If there are no authorized
BISSELL Service Centres in your area, a BISSELL Representative at

[e-mail] or at the phone number below will issue you a

Return Authorization Number and a pre-paid mailing label to return the unit to BISSELL
for warranty repair.

-- The machine should be returned with a photocopy of your proof of purchase. (Your
dated sales receipt is your warranty - do not send original.) If you need information
about repairs or replacement parts, or if you have questions about your warranty,

e-mail: [e-mail].

Or call: BISSELL Customer Service

1-800-263-2535
Monday - Friday
8 a.m. - 4:30 p.m. (E.S.T.)

Or write: BISSELL Ltd.,

ATTN: Customer Service,
Box 1003,
Niagara Falls, Ontario, L2E 6W2

*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY.

BISSELL LTD. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED
WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE
PRODUCT.

THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR
WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.

About Your Warranty

©2002 BISSELL HOMECARE, Inc.
BISSELL Ltd.,
Niagara Falls, Ont., L2E 6W2
All rights reserved. Printed in USA.
Part Number 310-4200

Visit our Web Site at:
www.bissell.com
Scotchgard is a trademark of 3M