DC PARALLEL
SHAFT
Specifications
GEARMOTORS
Gearhead
Gearing: AGMA class 9 heat treated steel
Housing: Precision machined die cast
aluminum
Lubrication: Lifetime oil bath, sealed and
gasketed
Bearings: Needle and thrust ball
Shafts: Hardened steel
Mounting: Face or base, any angle
Finish: Gloss black powder coat
Additional Information
348 Series PMDC
Part Number Speed 12V RPM Torque (in-lbs) Input HP Gear Ratio Stages OHL* Amps Shipping Wt. Brush
12V PMDC
011-348-3200 8.3 310** 1/6 215.6 3 500 5.51 16 A
011-348-3080 22 300** 1/6 81.8 3 500 11.00 16 A
011-348-3060 30 285 1/6 58.3 3 395 13.98 16 A
011-348-3030 64 150 1/6 28.1 2 290 13.98 16 A
011-348-3015 121 78 1/6 15.0 2 250 13.98 16 A
011-348-3010 170 57 1/6 10.6 2 240 13.98 16 A
011-348-3006 360 27 1/6 5.0 2 210 13.98 16 A
348 Series Parallel Shaft DC
UP TO 350 IN-LBS CONTINUOUS
For up to 350 in-lbs., our 348 Series offers more standard
voltages, mountings and speeds.
Motor
Speed: Variable with appropriate
control, (1.37 form factor max)
Rotation: Reversible
Bearings: Ball
Insulation: Class F
Enclosure: TENV
Features:
Rear tapped hole for encoder mount
Wiring diagram pages 88-91
Optional Features
Junction box kit
Part numbers:
P198-100-9111, 2 58” dia.
P198-100-9121, 3 13” dia.
P198-300-0000, 3 38” dia.
• Shaft-mount encoder
• Accessory shaft
See pages 86-87 for additional
accessories
Part Number Speed 24V RPM Torque (in-lbs) Input HP Gear Ratio Stages OHL* Amps Shipping Wt. Brush
24V PMDC
011-348-5200 8.3 310** 1/8 215.6 3 500 2.50 14 A
011-348-5080 22 300** 1/8 81.8 3 500 4.50 14 A
011-348-5060 30 230 1/8 58.3 3 395 5.18 14 A
011-348-5030 64 112 1/8 28.1 2 290 5.18 14 A
011-348-5015 121 59 1/8 15.0 2 250 5.18 14 A
011-348-5010 170 40 1/8 10.6 2 240 5.18 14 A
011-348-5005 360 19 1/8 5.0 2 210 5.18 14 A
Part Number
90V or 130V PMDC
011-348-4200 8.3 12 310** 1/8 215.6 3 500 1.33 14 D
011-348-4170 11 16 310** 1/8 170.0 3 500 1.33 14 D
011-348-4100 17 25 350** 1/8 102.4 3 500 1.33 14 D
011-348-4080 22 32 300** 1/8 81.8 3 500 1.33 14 D
011-348-4060 30 43 300** 1/4 58.3 3 395 2.30 20 D
011-348-4050 36 52 300** 1/4 48.7 3 350 2.30 20 D
011-348-4040 42 61 300** 1/4 42.9 3 350 2.30 20 D
011-348-4030 64 92 235 1/4 28.1 2 290 2.51 20 D
011-348-4020 94 136 160 1/4 19.1 2 250 2.51 20 D
011-348-4015 121 175 125 1/4 15.0 2 250 2.51 20 D
011-348-4010 170 246 90 1/4 10.6 2 240 2.51 20 D
011-348-4005 360 520 40 1/4 5.0 2 210 2.51 20 D
* Maximum overhung load on center of output shaft. ** Output torque is gear limited.
*** Units rated for 90V 1.37 form factor drive. May be run with 1.05 form factor drive at 130V.
Speed
90V RPM
Speed
130V RPM***
Torque (in-lbs) Input HP Gear Ratio Stages OHL* Amps Shipping Wt. Brush
20
Gear & Engineering Corp.
348 Series Parallel Shaft DC
348 DC 12V
2.94
6.02
#10-32 TAP
348 DC 24V & 90V
2.94
3.13 DIA.
10.27
OPTIONAL
J-BOX
A
OPTIONAL
J-BOX
1.50
.40
1.45
.40
2.00
.75 DIA.
2.00
3.50
3/16 SQ. X
1" LONG KEY
3/16 SQ. X
1" LONG KEY
4.08
3.63
2.25
4.00
4.08
3.63
2.25
.91
3.63
(4) 0.28 DIA.
HOLES
(4) 0.25-28
UNF-2B
5.12
(4) 0.25-28
UNF-2B
DC PARALLEL
SHAFT
GEARMOTORS
6.02
B DIA.
#10-32 TAP
HP V A B
1/8 90 10.26 3.13
1/8 24 10.34 3.13
1/4 90 12.26 3.38
1.50
1.45
.75 DIA.
3.50
4.00
.91
5.12
3.63
(4) 0.28 DIA.
HOLES
Gear & Engineering Corp.
21
Loading...