Bison Gear & Engineering 336 Series Catalog Page
336 Series Parallel Shaft DC
UP TO 300 IN-LBS CONTINUOUS
For up to 300 in-lbs., our 336 Series offers a wider range
of speed and mounting options.
Specifications
Gearhead
Gearing: AGMA class 9 heat treated steel
Housing: Precision machined die cast aluminum
Lubrication: Lifetime oil bath, sealed and gasketed
Bearings: Needle and thrust ball
Shafts: Hardened steel
Mounting: Face or base, any angle
Finish: Gloss black powder coat
Additional Information
Motor
Speed: Variable with appropriate
control, (1.37 form factor max)
Rotation: Reversible
Bearings: Ball
Insulation: Class F
Enclosure: TENV
Features:
Rear tapped hole for encoder mount
Wiring diagram pages 88-91
See pages 86-87 for additional accessories
Optional Features
Junction box kit
Part numbers:
P198-100-9111, 2.58” dia.
P198-100-9121, 3.13” dia.
P198-300-0000, 3.38” dia.
• Shaft-mount encoder
• Accessory shaft
336 Series PMDC 90V or 130V 5/8” Shaft
Part Number
Speed
90V RPM
011-336-1329 5.9 8.5 183** 1/20 329.1 3 400 0.33 10 B
011-336-1208 8.7 13 293 1/20 208.0 3 400 0.60 10 B
011-336-1091 20 29 140 1/20 90.9 3 385 0.60 10 B
011-336-1053 34 49 85 1/20 52.9 2 344 0.60 10 B
011-336-2082 22 32 300** 1/8 81.8 3 322 1.16 13 D
011-336-2060 30 43 230 1/8 58.3 3 291 1.33 13 D
011-336-2043 42 61 166 1/8 42.9 3 250 1.33 13 D
011-336-2028 64 92 112 1/8 28.1 2 264 1.33 13 D
011-336-2019 94 136 76 1/8 19.1 2 242 1.33 13 D
011-336-2015 121 175 59 1/8 15.0 2 225 1.33 13 D
011-336-2011 170 246 42 1/8 10.6 2 208 1.33 13 D
011-336-2005 360 520 20 1/8 5.0 2 200 1.33 13 D
011-336-4043 42 61 300** 1/4 42.9 3 200 2.30 19.5 D
011-336-4029 64 92 235 1/4 28.1 2 236 2.51 19.5 D
011-336-4019 94 136 160 1/4 19.1 2 200 2.51 19.5 D
011-336-4011 170 246 90 1/4 10.6 2 206 2.51 19.5 D
011-336-4005 360 520 40 1/4 5.0 2 170 2.51 19.5 D
Speed
130V RPM***
Torque (in-lbs) Input HP Gear Ratio Stages OHL* Amps Shipping Wt. Brush
SHAFT
DC PARALLEL
GEARMOTORS
* Maximum overhung load on center of output shaft. ** Output torque is gear limited.
*** Units rated for 90V 1.37 form factor drive. May be run with 1.05 form factor drive at 130V.
336 DC
A
C
2.94
#10-32 TAP
OPTIONAL
J-BOX
B DIA.
.59
1.50
2.00
1.45
3/16 SQ.
x 1" KEY
.62 DIA.
.28 DIA. (4 HOLES)
HP A B C
1/20 8.53 2.58 5.60
1/8
10.34 3.13 6.02
1/4 12.27 3.38 6.23
3.38
4.08
3.38
2.25
4.00
.862
3.50
0.25-28
UNF 2B
(4 HOLES)
5.12
*HDU(QJLQHHULQJ&RUS
19
Loading...