Installation and Operating
Instructions
This installation manual will help you
obtain a safe, efficient, dependable
installation for your fireplace and
chimney system. Please read and
understand these installation instructions
before beginning your installation.
CAUTION: Do not attempt to modify
or alter the construction of the fireplace
or its components. Any modification or
alteration of construction may void the
warranty, listings and approvals of this
system. In that case, Security Chimneys
International Ltd will not be responsible
for damages. Install the fireplace only as
described in these instructions.
PLEASE RETAIN THIS MANUAL
FOR FUTURE REFERENCE
WARNING: The fireplace cannot be
operated without a door. Consult your
dealer to select the correct door model.
2125 Monterey St., Laval, Quebec, Canada, H7L 3T6
Printed in Canada
Rev. 8 Oct 2006 PIBISPANO
• Hot! Do not touch! The glass
and surfaces of this appliance
will be hot during operation and
will retain heat for a while after
shutting off the appliance. Severe
burn may result.
• Carefully supervise children in
the same room as appliance.
• If small children are present in the home, it
is recommended that this appliance be used
with a fire screen kit.
Listed to standards:
ULC-S610, UL-127
Report # 192-5237
Printed in Canada Rev. 8 Oct 2006
PIBISPANO
25 YEAR LIMITED WARRANTY
• Security Chimneys International Ltd. warrants to the owner of a Security Fireplace that the wood burning fireplace will be
free from defects in material and workmanship, under normal use and service, for a period of twenty-five (25) years from
the date of purchase.
A
proof
of
purchased
date
is
required
for
claims
to
be
processed.
This warranty is conditional to the
proper use, operation and maintenance of the fireplace. This 25-year warranty is limited to the residential use of the
product only.
This warranty shall be void if the fireplace is not installed and operated in accordance with the installation instruction
manual provided with the product and does not cover damage caused by misuse of the product.
• Security Chimneys International Ltd warrants the gold, nickel, brushed nickel plating on its doors and facades against
material and manufacturing defects for the lifetime of the fireplace. This lifetime warranty contains limitations which are
detailed below. Door and façade adjustments, as described in the installation manual, MUST be done at
installation time otherwise this warranty is void.
WARRANTY LIMITATIONS:
1. During the first year of the limited warranty, Security Chimneys International Ltd. will provide replacement parts (as
described in the document Details of the Limited 25 year Warranty) at no charge and will also pay for reasonable labour
costs incurred for repair work. All repairs must be approved by an authorised company official before any work is done.
Labour costs to be borne by Security Chimneys International Ltd. must not exceed the retail price of the parts replaced.
2. During the second through the fifth year of the limited warranty, Security Chimneys International Ltd. will provide
replacement parts (as described in the document Details of the Limited 25 year Warranty) at no charge should they be
found to be defective. Security Chimneys International Ltd. shall not be responsible for any labour costs.
2.1 During the second through the fifth year of the limited warranty, Security Chimneys International Ltd. will repair or
replace at no charge, any plated door or façade that is found to be defective and will assume the necessary labour costs to
replace this part.
3. During the sixth through the twenty-fifth year of the limited warranty, Security Chimneys International Ltd. will provide
replacement parts (if available and as described in the document Details of the Limited 25 year Warranty) at 50% of the
published List Price sheet. Security Chimneys International Ltd shall not be responsible for any labour costs.
3.1 After the sixth year of the limited warranty, Security Chimneys International Ltd. will repair or replace at no charge, any
plated door or façade that is found to be defective and will not assume any labour costs to replace this part.
4. The following parts are not covered by any warranty: Brass accessories installed on the fireplace: trims, louvers,
surround kits.
This warranty may not be extended by our representatives in any manner whatsoever.
The warrantor makes no warranties express or implied, written or oral, other than those specifically stated in this 25 year
limited warranty. The duration of any implied warranty including that of merchantability or fitness for any particular purpose
shall be limited to 25 years from the date of purchase.
The remedy for damages as the result of any defect in this product that has been warranted herein is limited to the replacement
of defective parts and does not include any incidental or consequential damages or expenses sustained in connection with the
product, including damage to property.
Security Chimneys International is not responsible for the inadequate performances of the fireplace caused by the
environment such as trees, buildings, roofs, wind, hills, mountains near by, which may cause negative pressures
inside the home or mechanical causes such furnaces, blowers or cloth dryers.
The chimney is covered by a separate warranty.
NOTE: Dated proof of purchase is required for recognition of this warranty.
FOR UNITED STATES ONLY:
Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
Details of The 25 Year Limited
Fireplace Warranty
Year 1:
Parts and labour (no charge)
(see on page for exclusions and conditions)
Air control assembly
Plate, lever
Blower assembly
Blowers, wires, thermo disc
Ceramic glass
Glass (thermal breakage)
Catalytic combustor
Combustor (thermal degradation and disintegration),
retainer
Air register assembly
Plate, lever
Door assembly
Door, latch assembly, hinges, glass retainer, gaskets
Facade assembly
Facade, hardware
Fire box assembly
Fire box, tube supports, tubes, deflectors
Refractory
Refractory (thermal breakage)
Paint
Doors, louvers, fireplace facade
Accessories
Log retainers, fire screen
Years 2 to 5:
Parts (no charge)
(see on page for exclusions and conditions)
Air control assembly
Plate, lever
Catalytic combustor
Combustor (thermal degradation and disintegration),
retainer
Air register assembly
Plate, lever
Door assembly
Door, latch assembly, hinges, glass retainer, gaskets
Facade assembly
Facade, hardware
Fire box assembly
Fire box, tube supports, tubes, deflectors
Years 6 to 25:
Parts at 50% of published list price
(see on page for exclusions and conditions)
Air control assembly
Plate, lever
Air register assembly
Plate, lever
Door assembly
Door, latch assembly, hinges, glass retainer, gaskets
Facade assembly
Facade, hardware
Fire box assembly
Fire box, tube supports, tubes, deflectors
Exclusions: Brass accessories installed on the fireplace: trims,
louvers, surround kits.
Conditions:
1. The 25-year warranty begins from the date of purchase of the
fireplace and is valid as long as this fireplace remains
installed in its original home. The fireplace must be
installed, operated and maintained in accordance with the
instructions described in the installation manual provided
with it. Any alteration, modification, accident, neglect or
abuse of the product will void this guarantee.
2. A slight discoloration of painted parts, expansion,
contraction or movement of certain parts, which cause light
clicking noises, is normal and is not a manufacturing defect.
3. Over firing of the fireplace (operation which causes metal
parts to become red) can cause significant damage, create a
fire hazard and voids the warranty.
4. Security Chimneys International is not responsible for the
inadequate performances of the fireplace caused by the
environment such as trees, buildings, roofs, wind, hills,
mountains near by, which may cause negative pressures
inside the home or mechanical causes such furnaces, blowers
or cloth dryers.
5. This warranty does not cover normal wear and tear like the
discolouration or peeling of painted parts, worn or cut
gaskets, chipped or cracked refractory.
6. Although your BIS fireplace is very efficient, it should not,
in any case, replace the main heating system of the home in
which it is installed. This fireplace is designed to
supplement heat and comfort to the existing main heating
system.
i
TABLE OF CONTENTS
1. SAFETY RULES FOR OPERATING THE BIS PANORAMA .............................. .. . 1
2. CERTIFICATION LABEL ................................................................................... 2
3. THE FIREPLACE.. .. .. .. ........................................................................................ 2
3.1 INTRODUCTION.............................. .. .. .. .. .. .. ................................................. 3
3.1.1 Parts Required
3.1.2 Additional Equipment (optional)
3.2 OPERATING THE BIS PANORAMA.... .. .. .. .. .. .. ................................................... 4
3.2.1.1 Fuel
3.2.1.2 First Fires
3.2.1.3 Catalytic Combustor
3.2.1.4 Combustion Control
3.2.1.5 Accelerated Combustion
3.2.1.6 Medium Combustion
3.2.1.7 Slow Combustion
3.2.1.8 Starting And Maintaining a Fire
3.2.1.9 Refuelling For Best Performance
3.2.1.10 Smoking – Causes and Troubleshooting
3.2.1.11 Important Notes
3.3 MAINTAINING YOUR BIS PANORAMA ............................................................10
3.3.1.1 Creosote
3.3.1.2 Chimney Maintenance
3.3.1.3 Dealing With a Chimney Fire
3.3.1.4 Catalytic Combustor
3.3.1.5 Doorframe Care
3.3.1.6 Ashes
3.3.1.7 Refractory Brick Replacement
3.3.1.8 Door Installation
3.3.1.9 Door Adjustment
3.3.1.10 Glass Care – Replacement
3.3.1.11 Glass Care – Cleaning
3.3.1.12 Gasket Replacement
3.4 FIREPLACE INSTALLATION .........................................................................14
3.4.1.1 Locating The BIS PANORAMA
3.4.1.2 Hearth Extension Requirements
3.4.1.3 Framing, Facing and Mantel
3.5 HOT AIR DUCTING INSTALLATION ........ .. .. .. .. .. ..............................................19
3.5.1.1 Gravity Kit
3.5.1.2 Forced Air Kit (not tested under EPA certification)
3.6 OUTSIDE AIR KIT ................................................................................... .. .. 23
3.6.1 Outside Air Installation
4. THE CHIMNEY ........................................................ .. .. .. .. .. ...............................24
4.1 CHIMNEY INSTALLATION NOTES ............ .. .. .. .. .. .............................................24
4.2 CHIMNEY INSTALLATION INSTRUCTIONS ...... .. .. .. .. .. ......................................25
4.3 OFFSET CHIMNEY INSTALLATION .. .. .. .. .. .. ....................................................28
4.4 ANGLED WALL RADIATION SHIELD............ .. .. .. .. .. .. .......................................31
4.5 CHIMNEY SUPPORT INSTALLATION................ .. .. .. .. .. .....................................32
4.6 CHIMNEY CHASE AND MULTIPLE TERMINATIONS .........................................33
4.7. CHIMNEY ADAPTOR.......... .. .. .. .. .. ................................................................33
4.8 INSTALLATION INSTRUCTIONS FOR MASONRY APPLICATION .... .. .. .. .. .. .. ...........34
5. PARTS AND COMPONENTS LIST ................................................ .. .. .. .. .. ...........35
6. OPTIONS ............................................ .. .. .. .. .. .....................................................36
7. APPENDIX (Specifications, Clearance To Combustibles, Replacement Parts).............36
1
1. SAFETY RULES FOR OPERATING YOUR
FIREPLACE MODEL BIS PANORAMA
Warning: An outside air kit must be installed on the fireplace model BIS
PANORAMA
Warning: The fireplace must be operated with the doors fully opened or fully closed.
If the doors are left partly opened, smoke may be drawn into the room. If the unit is
operated with the doors fully opened, the optional fire screen must be used.
• Use only Security Chimneys International glass doors specifically designed for the
model BIS PANORAMA fireplace.
• When cleaning the fireplace, the ashes should be placed in a metal container with a
tight fitting lid. The closed container of ashes should be placed on a non-combustible
floor or on the ground outside the house, pending final disposal. If the ashes are
disposed of by burial in soil or otherwise locally dispersed, they should be retained in
the closed container until all cinders have thoroughly cooled.
Caution: Never use gasoline, kerosene, charcoal lighter fluid or similar liquids to start or
rekindle a fire in this fireplace. Keep all such liquids well away from the
fireplace at all times.
Caution: Keep combustible materials at least 48 inches away from the front of the
fireplace opening.
Caution: Never leave children unattended when there is a fire burning in the fireplace.
Caution: Burn untreated wood only. Other materials such as wood preservatives, metal
foils, coal, plastic, garbage, sulphur or oil may damage the catalyst.
Caution: Do not operate without the catalytic combustor in place.
Caution: Never burn with the by-pass opened except for fire start-up and when
reloading the stove.
WARNING: THIS FIREPLACE HAS NOT BEEN TESTED WITH AN UNVENTED
GAS LOG SET. TO REDUCE RISK OF FIRE OR INJURY, DO NOT
INSTALL AN UNVENTED GAS LOG SET INTO THIS FIREPLACE.
2
3
2. CERTIFICATION LABEL
4
3. THE FIREPLACE
3.1 INTRODUCTION
The BIS PANORAMA fireplace is an energy efficient, heat circulating, close combustion
fireplace using the catalytic technology. You will receive a lifetime of comfort and
enjoyment from your fireplace provided it is installed, maintained and operated properly.
• Please read these instructions and retain this manual for future reference.
• Before beginning the fireplace installation, consult the local authorities to obtain your
building permit and check your local building codes. Install the fireplace only as
described in these instructions and using only Security Chimneys International
components.
• The BIS PANORAMA is not intended for use with a gas log. Failure to follow these
instructions will void the certification and the warranty of the fireplace and may result
in an unsafe installation.
3.1.1 Parts Required
• Fireplace model BIS PANORAMA
• Door set
• Louver set (Del Sol, Diamante, Fiori or Luna)
• 7" diameter chimney model Secure Temp
ASHT+
, Secure Temp
S-2100+
, Nova
Temp
HT6000+
, Nova Temp
HT6103+
or ACBI manufactured by Security Chimneys
International only, including:
- Chimney lengths
- Elbows (where necessary)
- Radiation shield, Attic radiation shield
- Roof flashing
- Rain cap
- Supports (if necessary)
• 7" diameter TUBINOX (or PROJET SS) and masonry adaptor kit for masonry
applications
• Outside air kit
3.1.2 Additional Equipment (optional)
• 5" flexible venting system (central forced air kit – Not EPA approved)
• Gravity venting system
• Panel for clean face option (only with gravity venting system)
• Fireplace fan kit
5
3.2 OPERATING THE BIS PANORAMA
3.2.1 Fuel
The BIS PANORAMA is designed to work best when fuelled with seasoned cordwood.
Hardwoods are preferred to softwoods since the energy content of wood is relative to its
density. Hardwoods will result in a longer burning fire and less frequent refuelling. A
moisture content of 15% to 20% (seasoned) is recommended. Excessively wet wood will
be difficult to burn and will result in lower efficiency, increased creosoting and plugging of
the catalytic combustor. Excessively dry wood will burn well but will also have higher
emissions and shorter burning time.
Do not burn scrap or garbage, treated wood or wood such as driftwood from the ocean
which has been exposed to salt or other chemicals. Salt or chemicals can corrode the
firebox and can shorten the life of the catalytic combustor. Do not burn large amounts of
paper, cardboard, Christmas tree branches or building construction materials. Intense
firing with these materials may overheat the fireplace, causing damage to the unit, a fire or
even possibly igniting a chimney fire if the chimney is creosoted. Overheating the unit
above 1000° C (1800º F) is harmful for the catalytic combustor; it can damage the catalyst
coating and can cause cracking of the substrate. Looking through the upper louvers, if the
top of the firebox is glowing, the unit is overheating,
3.2.2 First Fires
Before using the fireplace make sure to remove the plastic wrapping on the doors.
Remove all remaining glue with mild soap. Ensure that the door is well adjusted before
starting a fire (see page 12.)
The first 5 or 6 fires should be small fires of short duration (about 30 to 60 minutes).
This will help cure the refractory bricks. Ashes that will accumulate in the ashtray will
protect it from intense heat. The first fires may produce slight smoking due to drying of
the paint and steel and any dust accumulated on the fireplace will burn off at this time. It
may set off a smoke alarm located in the same room. For this reason the room should be
well ventilated for the first few fires.
3.2.3 Catalytic Combustor
The BIS PANORAMA is equipped with a catalytic combustor. Unburned by-products
of the wood fire are burned at lower temperatures as they pass through the combustor
resulting in less pollution, reduced creosote and higher efficiency. In order to have the
catalyst working, temperatures of the flue gases entering the combustor have to be higher
than 260 °C (500 °F). That is why the unit is equipped with a by-pass damper that
allows the draft air to by-pass the catalytic combustor. Opening the by-pass damper
control increases the draft allowing the unit to achieve proper operating temperatures
during a cold start-up. It also provides more draft to prevent smoke spillage when the
door is opened. When the catalyst light-off conditions are achieved, the combustor will
6
keep on going until it runs out of smoke. Note that the catalyst does not need to be
glowing to be working, it can work very well at temperatures well below the 538 °C
(1000 °F) level at which it will begin to glow. The best way to see if the catalyst is active
is to take a look at what is coming out of the chimney. If the catalytic combustor is
working you can will some white water vapour coming out, compared to a more
brown/grey smoke when the by-pass is opened. Do not burn any chemical chimney
cleaner; it can make the catalyst inactive.
3.2.4 Combustion Control
There is no flue damper in the BIS PANORAMA. As is common with airtight stoves, the
combustion air damper controls the air entering the firebox. This allows for a more
precise control of the fire. The combustion air damper knob is located on the left of the
bottom louver. It is opened when moved completely to the left. This control should be
in the closed position when the fireplace is not in use. This will minimise air leakage up
the chimney. The combustion air control and the by-pass damper control must be
opened before opening the door to minimise the possibility of back draft coming
into the room.
Figure 1
7
3.2.5 Accelerated Combustion
The maximum heat output for the
BIS PANORAMA is achieved by
burning with the combustion air damper
opened. By this method, the BIS
PANORAMA can produce up to
70,000 BTU of heat per hour.
However, it will be necessary to reload with wood every one or two hours. This is the
least efficient method of burning the BIS PANORAMA.
Use caution when firing with the combustion air control wide open. Only burn cordwood
in this manner. Small dry pieces of softwood and construction scraps will burn very
intensely using this method and may damage the firebox and catalytic combustor.
3.2.6 Medium Combustion
This is the recommended mode of
operating the BIS PANORAMA and
should be the one normally used since it
will deposit the least amount of
creosote on the glass and in the
chimney. The combustion air damper
must be _ closed.
The precise setting will depend on many factors, including chimney length and the
moisture content of the wood. For instance, a long chimney will necessitate closing the
damper more. To obtain the proper combustion, close the damper completely, and then
open it about _" to _". Three medium size pieces of wood should be burning on a bed of
hot coals. The heat output will be approximately 35,000 BTU per hour and the loading
time will be about every 3-4 hours. Softwoods may be burned using this method but the
time will be substantially reduced.
3.2.7 Slow Combustion
When the air combustion damper is
closed, the fireplace is in a slow
combustion phase. Slow combustion
will not stop the fire, but there will be a
noticeable change in the flame pattern.
The flames will be slow and may appear
dirty if the wood is too wet (moisture
content of 20% and more).
Always set the damper so that flames are visible, that way you maintain a good clean
combustion process. This method of burning should be used only after operating the BIS
PANORAMA with the air control opened to produce a hot fire for about an hour. Slow
8
combustion can be used at night in order to reduce the heat output and prolong the burn.
The loading time will be between 6-10 hours.
3.2.8 Starting And Maintaining a Fire
A) Place several crumpled up balls of newspaper in the firebox. Place small dry pieces of
kindling on top of the paper, criss-crossing the kindling so that there are air spaces in
between. Keep the fuel far back enough so that air can get underneath.
B) Open the air control fully and pull the by-pass damper control towards you to put it
in the OPEN position. Light the newspaper. Leave the door open until the fire is well
established.
C) Once the kindling fire is well established, add increasingly larger pieces of cordwood
until the fire is actively burning. Close the door and maintain an accelerated
combustion air set up in order to achieve combustor light-off conditions.
D) When the fire is burning well, close the by-pass damper control by pushing the control
rod in. It takes about 15 – 30 minutes with the by-pass opened to reach proper lightoff temperatures for the catalytic combustor.
E) Set the air control at the desired setting.
The unit will burn best with 2-3 pieces of cordwood spaced 1 to 2 inches apart and
allowing air to get under the fuel. Criss-crossing or arranging the fuel so that air can get
underneath, will help the fire get started easily.
3.2.9 Refuelling For Best Performance
To refuel the BIS PANORAMA at the end of a burn cycle where only hot embers remain
and flames are gone (not enough heat to maintain catalyst operating temperatures):
A) Open the by-pass and air controls fully.
B) Open the door approximately 1 inch and wait five seconds until the draft is stable.
Then open the door completely, load the fuel and close the door.
C) Keep the combustion air damper and the by-pass damper opened for 10 minutes
before closing it. It will ensure sufficient temperatures for combustor light off.
To refuel the BIS PANORAMA when the unit is still hot (Some burning fuel remaining
or a glowing combustor)
A) Open the by-pass and air controls fully.
B) Open the door approximately 1 inch, wait five seconds until the draft is stable and
then open it completely. Load the fuel, close the door and by-pass. (Temperatures
within the firebox should be enough to maintain catalytic operation)
9
Figure 2
3.2.10 Smoking – Causes and Troubleshooting
To reduce the likelihood of smoking when opening the doors, set the air damper to the
"accelerated combustion" position and open the by-pass damper before opening the
doors. Your fireplace has been designed and tested to provide smoke free operation.
Occasionally, there may be a small amount of smoking upon lighting the fire, until the
chimney heats up but this should not continue. If the fireplace does continue to smoke, it
is probably for one of the following reasons:
1. The door is partly open
Open the door fully.
2. Negative pressure in the house
As the fire burns, air goes up the chimney. This air must be replaced through leakage into
the house or through the outside air duct. When operating the BIS PANORAMA, open a
nearby window temporarily to check if there is adequate air replacement.
3. Fans operating (e.g.: range hood)
These fans draw air out of the house and may actually cause a negative pressure in the
house. Turn off all fans and open a nearby window to determine if this is the cause of the
problem.
Position registre de dérivée
By-pass position
10
4. Wet wood
Wet or tarred wood will smoulder and smoke instead of burn properly.
5. Dirty or blocked chimney
Check to make sure the chimney is clear and reasonably clean.
6. Chimney not long enough
The minimum chimney height is 12 ft., not including the fireplace height. The chimney
must extend at least 3 feet (915 mm) above its point of contact with the roof and at least
2 feet (610 mm) higher than any roof or wall within 10 feet (3 m) of it. When installed
with offsets, the minimum chimney height is 15 ft. Additional height will increase
draught and will decrease the tendency to smoke.
7. Poor chimney draft
With no fire, there should be sufficient draught to exhaust cigarette smoke introduced
under the baffle. Chimneys installed against an outside wall without protection may
generate back draught problems that will cause start-up problems. To prevent this, open
a nearby window, roll up a piece of paper and light it. Then, hold it in the upper part of
the firebox to warm up the chimney. Wait until the draught is sufficient, and then start
the fire.
8. Blower for central forced air kit operating (Not EPA approved)
Make sure that the blower is at the "off" position when you open the fireplace doors for
reloading.
3.2.11 Important Notes
1. Do not block the hot air vents of the fireplace, as this will cause the fireplace to
overheat.
2. Never start a fire using gasoline, kerosene, charcoal lighter fluid or any other
combustible liquid.
3. Do not burn coal. The sulphur in coal will corrode the firebox.
4. Do not burn driftwood that has been in the ocean or salt water. The salt will corrode
the firebox and chimney.
5. Do not operate the unit with the door partly open since this may cause smoke to be
drawn into the room.
6. Do not burn wood in the area in front of the log retainers.
7. Do not abuse the unit by burning paper, or cardboard or construction material such as
pressed wood, plywood or lumber.
8. Do not allow the wood to smoulder or burn without flame, since this will produce
excessive creosote in the unit.
11
3.3 MAINTAINING YOUR BIS PANORAMA
3.3.1 Creosote
When wood is burned slowly, it produces tar and other organic vapours which combine
with expelled moisture to form a black deposit called creosote that accumulates on the
flue lining. When ignited, this creosote makes an extremely hot fire. If the creosote
accumulation is large, a creosote fire in the chimney can damage the chimney and overheat
the surrounding wood framing. Creosote formation in a chimney can be minimised by
making hot fires rather than slow burning, smouldering fires and by proper refuelling
techniques.
3.3.2 Chimney Maintenance
Regular chimney inspection and maintenance combined with proper operation will
prevent chimney fires. Keep your chimney clean. Do not allow more than 1/16" creosote
build up in your chimney. The amount of creosote will depend on variables such as
frequency of use and type of fire. We recommend that you:
1. Initially inspect the chimney system weekly. From this, you will learn how often it
will be necessary to clean your chimney.
2. Have your chimney cleaned by a qualified chimney sweep. If you wish to clean it
yourself, we recommend using a stiff plastic or non-metallic brush. If a metal brush is
used, its size should be slightly smaller than the flue to avoid damaging the chimney.
Do not use a brush that will scratch the stainless steel interior of the chimney.
3. Do not expect chemical cleaners to keep your chimney clean. The rain cap can be
removed for inspection and/or cleaning of the chimney. Using gloves, firmly grip the
lower portion of the rain cap. Turn the cap 1/8 of a turn counter-clockwise and lift it
off the chimney.
3.3.3 Dealing With a Chimney Fire
Regular chimney maintenance and inspection can prevent chimney fires. If you have a
chimney fire, follow these steps:
1. Close the fireplace doors and the combustion air damper.
2. Alert your family of the possible danger.
3. If you require assistance, alert your fire department.
4. If possible, use a dry chemical fire extinguisher, baking soda or sand to control the fire.
Do not use water as it may cause a dangerous steam explosion.
5. Check outside to ensure that sparks and hot embers coming out of the chimney are
not igniting the roof.
6. Do not use the fireplace again until a qualified chimney sweep or a Fire Department
Inspector has inspected your chimney and fireplace.
12
3.3.4 Catalytic Combustor
The BIS PANORAMA is designed with a catalytic combustor that will reduce pollution
emissions and creosote build up while improving thermal efficiency. In order to optimise
and maintain the combustor performance, it is important to visually check the combustor
at least 3 times during the heating season to determine if physical degradation has
occurred.
Catalytic combustors require little maintenance. Cleaning the combustor once a year,
preferably when your flue system is serviced, is sufficient for most users.
Warning: To prevent damage to your combustor, do not
• Drop the combustor (which is fragile compared to the rest of the unit –
so handle with care)
• Run water or compressed air through the combustor
• Try to clean the combustor with any sharp tool
Cleaning Procedure:
1. Rotate the retainers to
release the combustor
support plate while
holding it to make sure it
does not drop.
2. Rotate the support plate
and remove the
combustor.
3. Remove fly ashes on the
combustor using a soft
brush.
4. Put the combustor back in
place.
Figure 3
3.3.5 Doorframe Care
Use a glass cleaner and a soft cloth to polish the frame. Do not use abrasives such as steel
wool or steel pads for they may scratch the doorframe finish.
3.3.6 Ashes
Remove ashes only when the fire is out and the ashes are cold (24 to 48 hours after the
fire is out). Open the bottom louver and doors, lift the door trap lever, and remove the
plug on the door trap of the ashtray using gloves or a poker. Sweep the ashes in the
opening with a brush or any similar tool. Reinstall the plug on the door trap and pull
down the lever.
13
3.3.7 Refractory Brick Replacement
The intense heat of the fire will normally cause hairline cracks in the refractory. These
cracks can be minimised by proper curing as described in "First Fires". They will not
normally diminish the effectiveness of the refractory. If large cracks develop, then the
refractory should be replaced. To replace the refractory bricks, follow these steps:
1. Remove the front refractory
brick
2. Remove the bottom
refractory brick
3. Remove the left side
refractory brick
4. Remove the right side
refractory brick
5. Remove the back refractory
brick
To install the new refractory bricks,
follow the above steps in reverse.
Figure 4
3.3.8 Door Installation
The door must be installed only
when the installation of the BIS
PANORAMA is completed. All
you have to do is fit the male part of
the hinge, already fixed on the door,
in the female part, which is already
fixed on the fireplace.
To remove the door, simply pull the
door up from the hinges.
The adjustment of the door has been
set at the factory. If the fit is still
not perfect, you can adjust the door
using the hinge screws (see fig.6).
Figure 5
14
3.3.9 Door Adjustment
The door may need to be adjusted to
be completely airtight. For a door to
be considered air tight, a piece of
paper cannot be inserted in between
the façade of the fireplace and the
door gasket. The gasket air
tightness can be adjusted using the
adjustment screw located on the
fireplace façade at the bottom of the
fireplace opening. (An Allen key #
1/8 will be necessary for
adjustment).
Figure 6
3.3.10 Glass Care - Replacement
The glass used for the BIS PANORAMA is a high temperature ceramic glass. If the glass
breaks, it must be replaced with a ceramic glass. Tempered glass or ordinary glass will not
withstand the high temperatures of the BIS PANORAMA. Replacement ceramic glass
should be purchased from a Security Chimneys International dealer. Do not operate the
unit with cracked or broken glass.
3.3.11 Glass Care - Cleaning
The BIS PANORAMA is designed to keep the glass clean under normal operating
conditions. If the BIS PANORAMA is operated continuously with the combustion air
damper closed, the glass will tend to get dirty unless the fuel, firebox and glass are
maintained at hot temperatures (see "Refuelling For Best Performance”). To clean the
glass, there are a number of specially designed cleaners. Your authorised Security
Chimneys International dealer can recommend a suitable cleaner which is available in your
area. Regular household glass cleaners will not clean creosote. Do not use abrasives such
as steel pads, steel wool or oven cleaner as they will scratch the glass.
3.3.12 Gasket Replacement
Remove the door from the unit (see page 14) and lay it on a clean unabrasive surface. To
replace the gasket, first remove all of the old gasket and gasket cement. Make sure that
the surface is totally clean before applying new cement or adhesion problems may result.
Apply gasket cement to the gasket channel and install the new gasket. This replacement
part is available from your Security Chimneys International dealer in the following
dimensions:
Gasket
Length
Dimensions
Around glass
83"
5/16" dia.
On door frame
92"
5/8" dia.
15
Around ash trap
8"
2" wide x 1/4" thick
16
3.4 FIREPLACE INSTALLATION
3.4.1 Locating the BIS PANORAMA
1. The best place to install your fireplace is determined by considering the location of
windows, doors, and the traffic flow in the room where the fireplace is to be located,
allowing space in front of the unit for the hearth extension and the mantel, and taking
into consideration the location of the hot air ducts (optional), outside air kit and
chimney. If possible, you should choose a location where the chimney will pass
through the house without cutting floor or roof joists (see fireplace dimensions page
17).
2. Usually, no additional floor support is needed for the fireplace. The adequacy of the
floor can be checked by first estimating the weight of the fireplace system. Weights
are given in the appendix. Next, measure the area occupied by the fireplace that is
normally 38" X 24 _". Note the floor construction and consult your local building
code to determine if additional support is needed.
3. A minimum of 7’ (2134 mm) measured from the floor to the ceiling is required to
install the BIS PANORAMA. The appliance can be installed on a combustible floor
or on a base, leaving at least 6’8" (2032 mm) from the base of the unit to the ceiling.
4. When selecting the location, the chimney outlet position and the direction of the wind
are important factor affecting the chimney performance. To allow a maximum draft
and to reduce wind turbulence, the chimney must:
• Penetrate the highest part of the roof.
• Be installed as far as possible of roof offsets, trees or any other obstructions that may
cause wind turbulence and back drafts in the chimney.
• The least amount of offsets (elbows) possible.
17
3.4.2 Hearth Extension Requirements
The fireplace can be installed directly on a combustible floor. Combustible floor in front
of the fireplace must be covered with tile, marble, stone or any other non-combustible
material (fig. 7).
Figure 7
18
* The shelf may be lowered to 48 inches if the upper panel is
blocked by the panel for clean face option (BPCF) and that
hot air gravity ducts are used (7B30ZR-1).
3.4.3 Framing, Facing and Mantel
The construction of the framing, facing, and mantel must be in accordance with the
standards and the following illustrations (figures 8 to 12):
1. Frame the fireplace using 2" x 3" or heavier lumber.
2. WARNING: Combustible materials cannot be used in the space directly above the
fireplace (except for framing on the front facing). This area must remain empty for a
height of 6'8" (2032 mm) measured from the base of the appliance.
3. Frame the fireplace with vertical studs at the sides of the fireplace running from floor
to ceiling (see figure 8). If combustible facing is to be used, position the studs back,
from the front edge of the fireplace, a space the thickness of the facing material so that
the facing can be installed flush with the fireplace facing. Frame headers between the
vertical studs only as follows:
- Place 2" x 3" or 2" x 4" headers, only along the upper part of the front, side and
back faces. Do not put wood or any combustible material within the area above
the fireplace except on the front facing.
- Place headers only as required to support the facing and mantel.
4. The fireplace cannot be in contact with the house insulation material. Cover
the insulation with Gyproc panels or other rigid materials around the fireplace.
Figure 8
Figure 9
19
Figure 10
Figure 11
20
INSULATED CHASE CONSTRUCTION
Figure 12
21
Facing
1. Combustible wall (such as Gyproc) must be installed flush with the fireplace. It may
not project in front of and on the fireplace (i.e. the steel façade of the fireplace) (figure
15).
2. Decorative frame made of combustible material cannot project in front of and on the
fireplace steel front, in the space delimited by the width of the unit (38") and a height of
54" from the base of the appliance. (Figure 15)
3. Non-combustible materials such as brick, stone or ceramic tile may project in front of
and onto the fireplace facing (figure 14).
Mantel
The mantel must be installed at least 54" (1372 mm) above the base of the fireplace
(figure 13). The shelf may be lowered to 48 inches if the upper panel is blocked by the
panel for clean face option (BPCF) and that hot air gravity ducts are used (7B30ZR-1).
Figure 13
Figure 14
22
Figure 15
23
3.5 HOT AIR DUCTING INSTALLATION
Different hot air ducting systems can be installed with the BIS PANORAMA:
- Gravity kit
- Forced air kit (Not EPA approved) (p. 21)
3.5.1 Gravity Kit
Part List (7B30ZK-1)
(See Figure 16)
- 2 telescopic lengths 8" I.D.
- 2 90º elbows 8" I.D.
- 2 hot air outlet kits
(louvers and frames)
- 2 adaptors
See components list page 36.
The gravity kit allows you to block the upper grill of the fireplace. To do so, follow the
steps below:
a) Remove the upper grill and its frame from the fireplace.
b) Install the panel for clean face option (BPCF) making sure that the insulation strip is
installed inside.
c) The fireplace façade can be covered with non-combustible material (fig. 18).
The safety rules for hot air ducting gravity kit installations are the following:
Minimum height* 68" (1727 mm)
Maximum length See figure 17
* The height of the louver must be measured from the base of the BIS to the
middle point of the louver.
When installing the double outlet system, the hot air outlets can be installed in the same
room as the fireplace, or one or both of the outlets can be installed in adjacent or upper
rooms. Installing the ducts at different elevations will tend to exhaust more heat out of
the higher outlet (figure 17).
WARNING: both pipes of the gravity kit must be installed. Any other installation may
cause fire and void warranty.
Figure 16
24
25
Figure 17
Figure 18
26
The duct system must be installed respecting the following:
1. Remove the top and bottom plates closing up the 8" dia. holes on top of the fireplace. Then,
cut the insulation in order to obtain two 8" dia. openings. Fix the adaptors on the fireplace
openings by turning clockwise (figure 16.)
2. Maintain at least a 2" (50mm) clearance between the ducts and any combustible material; the
required hole size is 13" x 13" (330 mm x 330 mm).
Exception: For the grills, the framing can be 10 _" x 10 _" (275 mm x 275 mm) to
provide the clearance as required by the integral spacers on the double outlet duct system.
3. The maximum number of elbows in a run of duct is two.
4. Maintain at least 6 _" (160 mm) clearance from the outlet grill framing to a combustible
ceiling, side wall or mantel.
5. When traversing a combustible wall or floor, a firestop must be installed at the wall or floor
penetration. The hole size must be 13" X 13". (330 mm x 330 mm)
6. Do not connect the hot air ducts to a central heating system. Malfunction of the heating
system’s fan will cause the fireplace to overheat. A furnace duct is only single wall and not
double wall as is required for the BIS PANORAMA hot air exhaust.
7. Use only Security Chimneys International grills and components as described in this manual.
Other grills or registers, for example, may be too restrictive and may overheat the fireplace or
ceiling.
8. Do not use insulated flexible ducts, as they may overheat.
9. Do not use tees or any other components than the ones specifically listed here.
10. All ducts must extend upwards or horizontally. Never try to route the ducting downward.
11. The hot air outlet grills must be installed with the louvers pointing downwards in order to
prevent overheating adjacent ceilings.
27
3.5.2 Forced Air Kit (Not tested under EPA certification)
The knock-outs provided on the back and on the sides of the BIS PANORAMA allow
the connection of insulated flexible pipe which enables you to heat adjacent rooms up to
50 feet from the fireplace.
The ducting system must be installed as described below:
1. Fix the adaptor at the back and/or the side of the fireplace by twist-locking the
adaptor to the fireplace. You can use more than one outlet on the fireplace (figure 19).
2. Attach the 5" flexible pipe, using the collars provided. Important: Make sure that the
plastic wrapping around the flexible pipe will not be in contact with the fireplace.
3. Route the flexible pipe to the chosen location. The ducting system can be installed
either in an upper room or in a lower room.
4. Attach the flexible pipe to the fan, using the collars (figure 20).
5. Fix the decorative grill fan adaptor to the fan.
6. Attach a standard 3" x 10" grill to the adaptor.
7. Install the blower thermostat in that part of the house to be heated by the hot air duct.
Do not install the blower thermostat in the room where the fireplace is located. A
cooling thermostat can be installed in the same room as the unit. This thermostat will
turn on the blower when the room where the fireplace is located becomes too hot.
This option requires electricity. Make sure that the connections to the fan have been
made according to the local codes and comply with their requirements.
Figure 20
Figure 19
28
3.6 OUTSIDE AIR KIT
The installation of an outside air assembly is required on the BIS PANORAMA.
The outside air assembly must be installed according to the following requirements:
1. Duct length should be kept to a minimum. The maximum length of a 4" I.D. (100mm)
insulated flexible duct is 20 ft. (6.1 m). The duct can be extended to a maximum of 40
ft. (12 m) using a 6" I.D. (150mm) insulated flexible duct.
2. The air intake register must not be installed more than 10 ft. (3050 mm) above the
base of the fireplace.
3. The fresh air must come from outside the house. The air intake must not draw air
from the attic, from the basement or garage.
4. The air intake register should be installed where it is not likely to be blocked by snow
or exposed to extreme wind and well away from automobile exhaust fumes, gas meters
and other vents.
5. The duct and register may be installed above or below floor level.
3.6.1 Outside Air Installation
Make a 4 _" (110 mm) hole in the outside wall of the house at the chosen location. From
outside, place the outside air register in the hole (open side down) and fasten the register
to the wall, with screws as shown (see figure 22). Slip the pipe into the insulated sleeve.
Place the insulated pipe over the register tube and over the fireplace’s outside air
connector (see figure 23). At each end, carefully pull back the insulation and plastic cover
exposing the flexible pipe. Using the aluminium tape provided, wrap the tape around the
joint between the flexible pipe and the air inlets. Carefully push the insulation and plastic
cover back over the pipe. Using aluminium tape, fasten the plastic cover in place.
Figure 22
Figure 23
29
4. THE CHIMNEY
4.1 CHIMNEY INSTALLATION NOTES
1. If possible, install an interior chimney, as it will provide better performance. In areas
with continuous temperatures below 18° C (0° F), the use of an exterior chimney
increases the likelihood of operating problems such as low draft, high rate of
creosoting, and poor start-up characteristics. Exterior chimneys are also prone to
down drafting and flow reversal. Installations, which are located on lower floors in
the house, such as in a basement, in combination with outside chimney, are especially
prone to flow reversal.
2. The Security fireplace model BIS PANORAMA is listed only with Security
Chimneys International Ltd 7" dia. chimney systems (Secure Temp
S2100+
, Nova
Temp
HT6000+
, Secure Temp
ASHT+
, Nova Temp
HT6103+
and ACBI chimney systems.)
3. A chimney venting a fireplace shall not vent any other appliance.
4. The minimum chimney height is 12 ft. (3.7 m). In altitude, add 18" (450 mm) to the
chimney for every 2000 feet (600 m) above sea level.
5. All chimney installations must include at least one support. The maximum chimney
length that can be supported by the fireplace is 9 ft. (2.75 m) for Secure Temp
S2100+
/
Nova Temp
HT6000+
, 12 ft. (3.7 m) for Secure Temp
ASHT+
/ Nova Temp
HT6103+
and 20
ft. (6m) for ACBI chimney.
6. The chimney must extend at least 3 ft. (915 mm) above its point of contact with the
roof and at least 2 ft. (610 mm) higher than any wall, roof or building within 10 ft.
(3m) of it (Figure 24).
7. If the chimney extends higher than 5 ft. (1500 mm) above its point of contact with the
roof, it must be secured using a roof brace.
8. A rain cap must be installed on top
of the chimney. Failure to install a
rain cap may cause corrosion
problems.
9. Cut and frame square holes in all
floors, ceilings, and roof that the
chimney will go through to provide
a 2" (50 mm) clearance between the
chimney and any combustible
materials. Do not fill this 2" space
with insulation or any other
combustible material.
10. Portions of the chimney that may
extend through accessible spaces
must be enclosed to avoid contact
with combustible materials or
damage the chimney.
Figure 24
30
4.2 CHIMNEY INSTALLATION INSTRUCTIONS
1. Cut and frame the holes in the ceiling, floor and roof where the chimney will pass (see
figure 25). Use a plumb bob to line up the centre of the holes. The sizes are indicated
in table 1 for the floor and ceiling holes and table 2 (page 28) for the roof holes.
CHIMNEY
MODEL
SQUARE HOLE SIZE
OPENING
Secure Temp
ASHT+
Nova Temp
HT6103+
13 3/8" (340 mm)
Secure Temo
S2100+
Nova Temp
HT6000+
15 1/8" (384 mm)
ACBI:
Ceiling
(1 inch clearance)
Wall
15" (380 mm)
17" (432 mm)
Figure 25
Table 1
2. From below, install a firestop in each ceiling/floor separation through which the
chimney will pass. At the attic level, install an attic radiation shield from above.
(Figures 26 & 27).
3. For Secure Temp
ASHT+
/ Nova Temp
HT6103+
and Secure Temp
S2100+
/ Nova
Temp
HT6000+
chimneys, place the first chimney length on the fireplace. To lock it in
place, turn _ of a turn clockwise. With the ACBI chimney, you must use a starter
section before installing the first chimney length (figure 28). Continue installing
chimney lengths making sure to lock each length in place.
4. Every time the chimney passes through a ceiling or a wall, install the appropriate
firestop. When you reach the desired height, install the roof support. (Refer to
instructions included with the support). For the ACBI use a universal support.
5. Then, put the roof flashing in place and seal the joint between the roof and the
flashing with roofing pitch. (See figures 29 & 30). For sloping roofs, place the
flashing under the upper shingles and on top of the lower shingles. Nail the flashing
to the roof, using roofing nails.
6. Place the storm collar over the flashing, and tighten it with the bolt supplied. Finally,
seal the joint between the storm collar and the chimney, using silicone caulking.
7. Install the chimney cap.
31
Figure 26
Figure 27
32
AC CHIMNEY INSTALLATION
(AIR COOLED GALVALUME CHIMNEY)
Figure 28
NOTE : THE OUTSIDE AIR KIT IS MANDATORY FOR
BOTH FIREPLACE AND CHIMNEY
33
Figure 29
Figure 30
Table 2
ROOF DOWN SLOPE HOLE SIZE
SLOPE
Secure Temp
ASHT+
Nova Temp
HT6103+
Secure Temp
S-2100+
Nova Temp
HT6000+
ACBI
Roof Pitch7"7"
7"
0 *
13 3/8" (340 mm)
15 1/8" (384 mm)
15" (380 mm)
2/12
13 5/8" (345 mm)
15 3/8" (390 mm)
15 3/8" (390 mm)
4/12
14 1/8" (359 mm)
16" (406 mm)
16 1/8" (410 mm)
6/12
15" (380 mm)
17" (432 mm)
16 7/8" (430 mm)
8/12
16 1/8" (410 mm)
18 1/4" (465 mm)
18 1/4" (465 mm)
10/12
17 1/2" (445 mm)
19 3/4" (502 mm)
19 5/8" (500 mm)
12/12
19" (483 mm)
21 3/8" (545 mm)
21 3/8" (545 mm)
* CROSS SLOPE HOLE SIZE
ACBI CHIMNEY
34
4.3 OFFSET CHIMNEY INSTALLATON
The minimum chimney height when using elbows is:
Fireplace model
BIS PANORAMA
Chimney model
Secure Temp
S-2100+
/ Nova Temp
HT6000+
/
Secure Temp
ASHT+
/ Nova Temp
HT6103+
ACBI
Vertical installation
12 ft (3.66 m)
Two (2) elbows
15 ft. (4.57 m)
Four (4) elbows
17 ft. (5.18 m)
Table 3
After reaching the location requiring the elbow, proceed as follows:
Secure Temp
S2100+
/ Nova Temp
HT6000+
/ Secure Temp
ASHT+
/ Nova Temp
HT6103+
Chimneys
1. Install the first elbow; turn it in the required direction. Fasten it to the chimney with
the three (3) _" (12 mm) metal screws provided with the elbow.
2. Install the necessary chimney lengths to achieve the required offset. Lock the chimney
lengths together: it is recommended to use three (3) _" (12 mm) screws. If the offset
length is made of two (2) chimney lengths or more, use an offset support halfway up
the offset. If penetrating a wall, install a wall radiation shield (see figures 32 & 33).
3. Use another elbow to turn the chimney vertically. Secure the elbow, using three (3) _"
(12 mm) screws (provided with the elbow).
4. Use a plumb bob to line up the centre of the hole. Cut a hole for the chimney in the
ceiling/floor. Frame this hole as described previously (refer to page 28).
5. From below, install a firestop (See figure 26).
6. A support (ST+ or SO+) must be used on the first 15’ section (5 m.).
7. Continue with the regular installation.
ACBI Chimney
1. Install the first elbow. Turn it in the required direction. To lock it in place, turn 1/8 of
a turn. Fasten the straps attached to the elbow to the surrounding frame, using nails or
drywall screws (figure 31).
2. Install the necessary chimney lengths to achieve the required offset. Lock the chimney
lengths together. If penetrating a wall, use a wall radiation shield.
3. Use another elbow to turn the chimney vertically. Lock it to the chimney. Fasten the
straps attached to the elbow to the surrounding framing using nails or drywall screws.
4. Use a plumb bob to line up the centre of the hole. Cut a hole for the chimney in the
ceiling. Frame this hole as described previously.
5. From below, install a firestop. (See figure 27).
6. Continue with the regular installation.
35
ONE LENGTH BETWEEN ELBOWS
TWO LENGTHS BETWEEN ELBOWS
CHIMNEY
7”
ELBOW
DEVIATION
& LENGTH
8”
12”
18”
24”
36”
48”
8” & 36”
12” & 48”
18” & 48”
24” & 48”
36” & 48”
48” & 48”
DEVIATION
3 5/164 5/165 7/87 7/1610 _
13 5/815 3/816 7/1618
19 _
22 5/825 _
15º
LENGTH
15 11/1619 9/1625 3/831 3/1642 _
54 3/860 15/1664 13/1670 9/1676 3/887
99 9/
16
DEVIATION
7 7/169 7/1612 7/1615 7/1621 7/1627 7/1630 13/1632 13/1635 13/1638 13/1644 13/1650 13/
16
30º
LENGTH
20
23 _
28 11/1633 7/844 _
54 11/1660 9/1664
69 _
74 7/1684 13/1695 _
DEVIATION
10 5/1613 3/1617 3/821 5/830 1/838 5/843 7/1646 _
50 _
54 _
63 _
71 11/
16
Secure
Temp
ASHT+
Nova
Temp
HT6103+
45º
LENGTH
17 13/1620 5/824 7/829 1/837 5/846 1/850 15/1653 _5862 _
70 _
79 3/
16
ONE LENGTH BETWEEN ELBOWS
TWO LENGTHS BETWEEN ELBOWS
CHIMNEY
7”
ELBOW
DEVIATION
& LENGTH
8”
12”
18”
24”
36”
48”
8” & 36”
36”
48”
24” & 48”
36” & 48”
48” & 48”
DEVIATION
3 5/164 5/165 7/87 7/1610 _
13 5/815 _
16 _
18 1/1619 5/822 _
25 13/
16
15º
LENGTH
16
19 7/825 11/1631 _
43 1/1654 5/861 7/1665 _
71 1/1676 7/888 _
100 1/
16
DEVIATION
7 3/89 3/812 3/815 3/821 3/827 3/830 7/832 7/835 7/838 7/844 7/850 7/
8
Secure
Temp
S2100+
Nova
Temp
HT6000+
30º
LENGTH
20 11/1624 3/1629 3/834 9/1644 15/1655 5/1661 3/864 7/870 1/1675 _
85 5/896
ONE LENGTH BETWEEN ELBOWS
TWO LENGTHS BETWEEN ELBOWS
CHIMNEY
7”
ELBOW
DEVIATION
& LENGTH
---
12”
18”
---
36”
48”
---
36”
48”
---
36” & 48”
48” & 48”
DEVIATION
---
5 _7---
11 _
14 _
---
17 _19---
23 5/826 _
15º
LENGTH
---
32 _38---
55 _67---
77 1/882 7/8---
100 _
111 1/
8
DEVIATION
---
10 _
13 _
---
22 _
28 _
---
33 _
36 _
---
45 _
51 _
ACBI
30º
LENGTH
---
30 1/835 3/8---
51
61 3/
8
---
70 _
75 5/8---
91 _
101 5/
8
NOTE : With the ACBI chimney, a starting length of 6” high must be used on top of the fireplace before installing
Table 4
TOTAL HEIGHT
DEVIATION
36
Figure 31
Figure 32
37
4.4 ANGLED WALL RADIATION SHIELD
(RSM+, RSMI30, RSMI45)
When traversing a combustible wall with the chimney at a 30º or 45º angle, an angled
firestop or wall radiation shield must be installed. Only one is required.
Note: 45º angle for Canada only
In cold climate locations, we recommend that you use the insulated wall radiation shield
since it will maintain the home’s thermal barrier.
RSM+ and RSMI30, RSMI45
CHIMNEY – 7” dia.
ANGLE
HOLE SIZE
30º
340 mm x 845 mm (13 3/8" x 33 _ ")
Secure Temp
ASHT+
Nova Temp
HT6103+
45º
Canada
only
340 mm x 591 mm (13 3/8" x 23 _ ")
30º
380 mm x 972 mm (15" x 38 _ ")
Secure Temp
S2100+
Nova Temp
HT6000+
45º
Canada
only
380 mm x 657 mm (15" x 25 7/8 ")
ACBI
30º only
432 mm x 1080 mm (17" x 42 _ ")
Table 5
Figure 33
38
4.5 CHIMNEY SUPPORT INSTALLATION
UNIVERSAL ROOF SUPPORT
This support has three possible uses:
1. For Secure Temp
ASHT+
/ Nova Temp
HT6103+
and Secure Temp
S2100+
/ Nova
Temp
HT6000+
, it must be used on a roof to support the chimney.
2. It may be used on a floor, ceiling or roof above an offset to support the chimney
above the offset.
3. It may be used on a floor, ceiling or roof as a supplementary support when the
chimney height exceeds 15 ft. (4.6 m.).
Table 6 gives maximum height of supported chimney.
NOTE: For the ACBI chimney, a support section (ACBI7SL) must be used every 30
ft. (10 m) or the universal support (AC10SU) every 20 ft.
For roof support installation, refer to the instructions provided with the support.
UNIVERSAL OFFSET SUPPORT
This support is used to support the chimney above an offset. When the chimney offset
is used to traverse a wall this support may be used on the wall to support the chimney.
The maximum heights are given in Table 6. For offset support installation, refer to the
instructions provided with the support.
CHIMNEY MODEL
MAXIMUM HEIGHT OF SUPPORTED CHIMNEY
OFFSET SUPPORT
ROOF SUPPORT
Secure Temp
ASHT+
Nova Temp
HT6103+
24 ft. (8.54m)
27 ft. (8.84 m)
Secure Temp
S2100+
Nova Temp
HT6000+
16 ft. (5.49 m)
18 ft. (6.1 m)
Table 6
39
4.6 CHIMNEY CHASE AND MULTIPLE TERMINATIONS
For the purpose of this manual, a chimney chase is considered a part of the chimney
system rather than part of a building. The termination must be placed a minimum of 18"
(460 mm) above the chase.
For installations where more than one chimney is located in the same chase or within the
same area, we suggest that their terminations be separated by at least 16" (410 mm)
horizontally, and 18" (460 mm) vertically. This separation is to prevent smoke
migrating from one chimney to another (see figure 34).
Figure 34
4.7 CHIMNEY ADAPTOR
(Secure Temp
S2100+
/
Nova Temp
HT6000+
/
The fireplace is normally supplied
with a chimney adaptor suitable for
the Secure Temp
ASHT+
/ Nova
Temp
HT6103+
chimney. If you want to
install a Secure Temp
S-2100+
/ Nova
Temp
HT6000+
chimney, an adaptor is
available (7UCA) (figure 35). A
separate starter section will also be
required if ACBI chimney is installed.
Figure 35
40
4.8 INSTALLATION INSTRUCTIONS FOR MASONRY APPLICATION
WARNING: Before starting the installation, the masonry chimney must be inspected by
a qualified sweep.
The following requirements must be respected:
1. The chimney must be absolutely clear of any soot residue or creosote. Check for cracks, loose or missing
bricks that could inhibit correct installation of the liner.
2. The clearance to combustible must be a minimum of 1" between the outside of the masonry and any wood
framing or loose insulation.
3. The chimney must be built in accordance with the current building code.
4. No other appliance can be connected to the same chimney.
5. The clearances to combustible for the BISUMA or BISPMA and BISUMA30 or BISPMA30 connectors are 2"
on the side and bottom and 16" at the top.
6. The connector parts are not necessary if the connection between the insulated length and the stainless
steel liner is done within the masonry chimney.
Installation:
The chimney must be relined with a stainless steel liner model Tubinox or Projet SS of the same diameter as
the outlet of the fireplace.
For connection at 45º angles, a special connector (BISUMA for the BIS Ultra fireplace or BISPMA for the
BIS Panorama fireplace) must be used to connect the liner to the insulated chimney. For connection at 30º,
use the BISUMA30 or BISPMA30 connectors.
Follow these steps:
1- Position the fireplace in its location. Temporarily
install the ASHT+ elbow on the top of the fireplace
and, using a level, mark with an oval the location
where the flue liner will enter the masonry chimney.
2- In the middle of the oval, drill a hole in the masonry
chimney at 45º or 30º.
3- Increase the size of the hole until a 45º or 30º
Tubinox liner elbow can be easily slipped through.
4- Slide the liner down from the top of the masonry
chimney until you reach the hole level.
5- Slip through the hole a 45º or 30º liner elbow and
connect it to the liner.
6- Add a small liner section to the liner elbow that will
allow the liner to extend at least 12” (measured at the
top of the liner) from the masonry chimney.
7- Seal the opening around the liner with high
temperature refractory cement.
8- The next steps must be done in the following order:
A. Select the ASHT + length that will fit between the
elbow and the liner so that it will slide at least 2"
over the liner section. (You may need to cut the
liner for a better fit).
See typical installation illustrated below.
B. Take that section and the BISUMA or BISPMA (BISUMA30 or BISPMA30) cover and slide it over the
liner. Make sure you have enough opening to be able to install the ASHT+ elbow without difficulty.
C. Install the 45º or 30º elbow on the fireplace.
D. Slide the length section back down on the elbow and twist lock the two together.
E. Pull the cover down over the length and install the insulation pad over the liner; be careful to cover the liner
completely.
F. Slide back the cover over the insulation and fix it in place using the 3 metal screws supplied.
41
5. PARTS AND COMPONENTS LIST
ACBI Chimney
Description
Part
No.
Lengths 7" dia.
12" length ACBI7L12
18" length ACBI7L18
36" length ACBI7L36
48" length ACBI7L48
15º elbow ACBI7E15
30º elbow ACBI7E30
Starter section ACBI7SBA
Starter section, 30º ACBI7SBA30
Rain cap ACBI7CPR
Spark arrester cap PE+
Supports
Support section ACBI7SL
Universal support AC10SU
Firestop
Firestop ACBI7BF
Radiation shield ACBI7RS
Attic radiation shield ACBI7RSA
Insulated wall radiation shield 30º AC10RSMI30
Outside air kit (chimney) AC ZI
(flex, insulation, outside register and coupling)
Flat roof flashing ACBI7FR
Adjustable Roof Flashings
1/12 - 7/12 (5º - 30º) ACBI7FAR
8/12 - 12/12 (30º - 45º) ACBI7FBR
Storm collar AC10FC
PARTS AND COMPONENTS LIST
Fireplace
Description:
Part No.
Victorian arch shape door, gold plated 24K
BPVG
Victorian arch shape door, black
BPVBK
DEL SOL louver set
DEL SOL
DIAMANTE louver set
DIAMANTE
FIORI louver set
FIORI
LUNA louver set
LUNA
Outside air kit
UZI
42
6. OPTIONS (Fireplace)
Description
:Part No.:
Complete double ducting system including: 2 elbows 90º, 2 telescopic
lengths, 2 grill supports and 2 black grills
7B30ZK-1
Black grill with support
7B30ZO
Brass grill for 7B30ZK
7B30ZGB
Panel for clean face option
BPCF
Elbow 90º, 8" dia.
7B26ZE90
Elbow 45º, 8" dia.
7B26ZE45
Telescopic length, 8" dia.
7B26ZLA
Adjustable length, 8" dia. (2" - 5")
7B26ZL2A
Radiation shield
7B26ZR
forced air kit including: adaptor and 2 clamps (BISAF), Blower (BISZY),
Blower variable speed control (VRUW), Thermo-disk (VTU) and fan
to flex adaptor (BISAVF).
BISFWK-1
Flex adaptor and 2 clamps
BISAF
Flexible pipe 5" D.I. x 15 ft. Long
5FLEX15
Flexible pipe 5" D.I. x 30 ft. Long
5FLEX25
Blower for central forced air kit
BISZY
Blower variable speed control with decorative wall plate for (BISZY)
VRUW
Thermo-disk, on/off blower control for (BISZY)
VTU
Thermostat 24V kit (heating and cooling)
HCTW
Back draft damper
BISBD
Adaptor for fan to flexible pipe
BISAVF
Other Options:
Cast-iron corner ornaments with magnets
APPC-01
Cast-iron corner ornaments with magnets
APPCS-02
Cast-iron top ornament with magnet
APP-03
Panel for clean face option
BPCF
Heat activated on/off pre-wired fan kit
UZY3
Masonry chimney adaptor
BISPMA
7. APPENDIX
SPECIFICATIONS
Weight 385 lbs.
Height 45"
Width 38"
Depth 24 1/2"
Chimney weight ASHT+ (7" dia.): 7.8 lbs./ft.
Chimney weight S2100+ (7" dia.): 12 lbs./ft.
CLEARANCE TO COMBUSTIBLES
The following clearances meet the minimum requirements for a safe installation
Side wall: 24" (457 mm) measured from the doors edge
Ceiling: 6’ 8" (2032 mm) measured from the base of the fireplace
Fireplace enclosure: Bottom: 0"
Side: 0"
Back: 0"
Top: Do not fill the space above the fireplace with any material
Chimney: 2" (50 mm)
Mantel: 54" (1372 mm) measured from the base of the fireplace or 48" if installed with
clean face panel option (BPCF) and gravity kit.
REPLACEMENT PARTS
43
Front refractory PR-SR2113
Back refractory PR-SR2056
Right side refractory PR-SR2057D
Left side refractory PR-SR2057G
Bottom refractory PR-SR2055
Catalytic combustor PR-SR2110
Catalytic combustor stainless steel casing PR-SR2111
Catalyst air tube (front) PR-SR2053
Secondary air tube (rear) PR-SR2051
Cast-iron log supports (2) 7B30B2CH
Louver frame (top) PR-SR2131
Louver frame (bottom) PR-SR2130
Ash tray cap PR-SR7B30B2CF01
Ash tray kit PR-B2GA1
Ash tray PR-BISUZH
Fireplace top PR-SR2432
Fireplace left side PR-SR2435
Fireplace right side PR-SR2434
Fireplace back PR-SR2436
Touch up paint (Forrest Paint Metallic Black) SBMB6309
Wooden handle door PR-SR1787
Wooden handle by-pass PR-SR2072
Rod and lock PR-SR2118
Ceramic glass panel: (Victorian door) PR-SR2107
Glass gasket PR-SR1823E
Door gasket PR-SR1823D
Hinges set (door and fireplace) PR-SR2395P
Top louver PR-SR2143DELSOL
PR-SR2143DIAMANTE
PR-SR2143FIORI
PR-SR2143LUNA
PR-SR2143STRADA
Bottom louver PR-SR2144DELSOL
PR-SR2144DIAMANTE
PR-SR2144FIORI
PR-SR2144LUNA
PR-SR2144STRADA
Loading...