BIRO 44TL Operating And Service Manual

MODEL 44TL POWER MEAT CUTTER

OPERATING AND SERVICE MANUAL

TRUE LEFT OPERATION

REVISED – Applicable to Model 44 Starting with Serial No. 3850 Except as Noted

* IMPORTANT NOTICE *

This Manual contains important safety instructions

which must be strictly followed when using this equipment.

PTCT Md 44TL
368-8-13-2

CLEANING

SHARP MOVING BAND TYPE SAW BLADE

TO AVOID SERIOUS PERSONAL INJURY

ALWAYS Turn Off, Unplug from Power Source and Perform Lockout/Tagout Procedure to this
Machine BEFORE Cleaning or Servicing.

ONLY Use Recommended Cleaning Equipment, Materials and Procedures.

NEVER Spray Water or Other Liquid Substances Directly at Motor, Power Switch or any Other

Electrical Components.

ALWAYS Thoroughly Clean Equipment at least Daily.

CLEANING THE BIRO POWER CUTTER:

Disconnect electrical power to the machine before cleaning. Parts to be removed have been made accessible and
can be removed without tools. Notice in the drawing below that all parts are numbered. Each part should be
removed for cleaning in the numbered sequence shown. To ensure cleaner cuts, keep the parts on the cleaning
system in good condition. Parts on the cleaning system which should be checked weekly, and changed as
required as follows: Wheel Cleaners (Part No. 179), Saw Cleaners (Part No. 131), Saw Guide in Stationary Bar
(Part No. 119A), Upper Saw Guide (Part No. 602B), Lower Blade Back-Up Guide (Part No. 605) and Nylon
Filler (Part No. 177).

Right hand version shown

18

LIMITED WARRANTY:
WARRANTY: The BIRO Manufacturing Company warrants that the Model 44TL Power Meat

Cutter will be free from defects in material and workmanship under normal use and with
recommended service. BIRO will replace defective parts, which are covered by this limited
warranty, provided that the defective parts are authorized for return, shipping charges prepaid, to
a designated factory for inspection and/or testing.

DURATION OF WARRANTY: The warranty period for all parts covered by this limited
warranty is one (1) year from date of Inspection/Demonstration as advised on the returned
Warranty Registration card, or eighteen (18) months from original factory ship date, whichever
occurs first, except as noted below.

PARTS NOT COVERED BY WARRANTY: The following are not covered by this limited
warranty: wearable parts on the cleaning system such as wheel cleaners (Item No. 179), saw
blade cleaners (Item No. 131), blade backup guides (Item No’s. 602B, 605 and 119A), and the
nylon filler (Item No. 177). This limited warranty does not apply to machines sold as used,
rebuilt, modified, or altered from the original construction in which the machine was shipped
from the factory. (WATER CONTAMINATED ELECTRICAL SYSTEMS ARE NOT
COVERED UNDER THIS LIMITED WARRANTY.) BIRO is not responsible for electrical
connection of equipment, adjustments to the switch controls or any other electrical requirements,
which must be performed only be a certified electrician. BIRO is not responsible for service
charges or labor required to replace any part covered by this limited warranty or for any damages
resulting from misuse, abuse, lack of proper or recommended service.

EXCLUSION OF WARRANTIES AND LIMITATION OF REMEDIES: BIRO gives no
warranties other than those expressly stated in this limited warranty. THE IMPLIED
WARRANTY OF MERCHANTABILITY, THE IMPLIED WARRANTY OF FITNESS FOR
PROCESSING OF FOOD PRODUCTS, AND ALL OTHER IMPLIED WARRANTIES ARE
SPECIFICALLY EXCLUDED. BIRO IS NOT LIABLE FOR CONSEQUENTIAL OR
INCIDENTAL DAMAGES, EXPENSES, OR LOSSES. THE REMEDIES PROVIDED IN
THIS BIRO LIMITED WARRANTY ARE PURCHASER’S SOLE AND EXCLUSIVE
REMEDIES AGAINST BIRO.

REGISTRATION CARDS: You must sign, date, and complete warranty registration card
supplied with each machine. The warranty card must be returned to The BIRO Manufacturing
Company for proper registration. If no warranty card is returned to BIRO, the warranty period
will begin from the date the machine was originally shipped from the factory.

HOW TO GET SERVICE:

1. Contact the agency from whom you purchased the machine; or

2. Consult the yellow pages of the phone directory for the nearest authorized dealer; or

3. Contact BIRO Mfg.Co. for the nearest authorized service agency in your area.

THE BIRO MANUFACTURING COMPANY

1114 W. Main Street
Marblehead, OH 43440-2099 U.S.A.
Ph. 419-798-4451 Fax [phone]

Email: [e-mail]

www.birosaw.com

ITEM No.: 18313-368

19 PTCT Md 44TL-368-8-13-2