Biro 1056 Parts List

HEAVY HORSEPOWER GRINDER

OPERATING MANUAL & PARTS LIST

Models 342, 542, 548, 552, 7542, 7548, 7552, 1056, 1556

Applicable on HHP Grinders starting with Serial No. 2250

PTCT

H400-078A

7-04-22

IMPORTANT NOTICE

This Manual contains important

safety instructions which must

be strictly followed when using

this equipment.

Biro Designed Biro Built

PTCT

H400-078A

8-08-23

TABLE OF CONTENTS

Page

NOTICETOOWNERSANDOPERATORS......................................... 1

SAFETYTIPS............................................................... 2

INSTALLATION ............................................................. 3

UNCRATINGANDSETUP ................................................... 3

MOTORWIRING........................................................... 3

ELECTRICALREQUIREMENTS................................................ 4

MOTORSPECIFICATIONS................................................... 4

WIRINGDIAGRAMS .......................................................... 5

OPERATION................................................................ 6

TOPROCESSPRODUCT.................................................... 6

CLEANING................................................................. 7

MAINTENANCE ............................................................. 8

GRINDINGBOWLINSTALLATION............................................. 8

BEARINGHOUSINGLUBRICATION............................................ 9

ROLLER CHAIN AND DRIVE SPROCKET LUBRICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

MAINDRIVECHAINTENSION ................................................ 9

PARTS DIAGRAMS, MAIN BODY AND DRIVE SYSTEM

FOR 3, 5, 7

HORSEPOWERGRINDERS........................................10

PARTS DIAGRAMS, BOWL AND TRAY SECTION

FOR 3, 5, 7

HORSEPOWERGRINDERS........................................11

ELECTRICAL CONTROLS FOR 3, 5, 7

HORSEPOWERGRINDERS................12&13

PARTS DIAGRAMS, MAIN BODY AND DRIVE SYSTEM FOR

10&15HORSEPOWERGRINDERS............................................14

PARTS DIAGRAMS, BOWL AND TRAY SECTION FOR

10&15HORSEPOWERGRINDERS............................................15

ELECTRICAL CONTROLS FOR 10 & 15 HORSEPOWER GRINDERS . . . . . . . . . . . . . . . . . . . . 16

OPERATOR'SSIGNATUREPAGE................................................17

LIMITEDWARRANTY.........................................................18

PARTS DIAGRAMS, BOWL AND TRAY SECTION

FOR 3, 5, 7

HORSEPOWERGRINDERS........................................11

PARTS DIAGRAMS, BOWL AND TRAY SECTION FOR

10&15HORSEPOWERGRINDERS............................................15

ELECTRICAL CONTROLS FOR 10 & 15 HORSEPOWER GRINDERS . . . . . . . . . . . . . . . . . . . . 16

OPERATOR'SSIGNATUREPAGE................................................17

LIMITEDWARRANTY.........................................................18

ELECTRICAL CONTROLS FOR 3, 5, 7

HORSEPOWERGRINDERS................12&13

PARTS DIAGRAMS, MAIN BODY AND DRIVE SYSTEM FOR

10&15HORSEPOWERGRINDERS............................................14

AND WARNING LABELS & LOCATIONS ON GRINDERS

BIRO’s products are designed to process food products safely and efficiently. Unless the operator is properly trained and supervised, however, there is the possibility of a serious injury. It is the responsibility of the owner to assure that this machine is used properly and safely, strictly following the instructions contained in this Manual and any requirements of local law.

No one should use or service this machine without proper training and supervision. All operators should be thoroughly familiar with the procedures contained in this Manual. Even so BIRO cannot anticipate every circumstance or environment in which its products will be used. You, the owner and operator, must remain alert to the hazards posed by the function of this equipment – particularly the ROTATING GRINDING WORM, which can severely injure an inattentive operator amputating fingers and limbs. No one under eighteen (18) years of age should operate this equipment. If you are uncertain about a particular task, ask your supervisor.

This Manual contains a number of safe practices in the SAFETY TIP section. Additional warnings are placed throughout the Manual. Warnings related to your personal safety are indicated by:

Warnings related to possible damage are indicated by:

BIRO also has provided warning labels on the equipment. If any warning label or Manual becomes misplaced, damaged, or illegible, please contact your nearest Distributor or BIRO directly for a replacement.

Remember, however, this Manual or the warning labels do not replace the need to be alert and to use your common sense when using this equipment.

This Manual applies to machines with serial number 2250 and higher.

NOTICE TO OWNERS AND OPERATORS

- NOTE -

A copy of this manual is included with each HEAVY HORSEPOWER GRINDER.

The descriptions and illustrations contained in this manual are not binding.

The manufacturer reserves the right to introduce any modification

without updating the manual.

SAFETY TIPS

ROTATING GRINDING WORM

TO AVOID SERIOUS PERSONAL INJURY

NEVER Touch This Machine Without Training and Authorization By Your Supervisor.

ALWAYS Read Operation and Service Manual BEFORE Operating, Cleaning or Servicing.

NEVER Place Hands Into Machine Input or Output Openings.

NEVER Open Machine During Operation.

ONLY Use a Qualified Electrician to Install According to Local Building Codes: Machine MUST

Be Properly Grounded.

ALWAYS Connect to Proper Voltage & Phase.

ONLY Install on Level, Non-Skid Surface in a Clean, Well-Lighted Work Area Away From

Children and Visitors.

NEVER Use This Machine For Non-Food Products.

NEVER Operate Machine With Tray And/Or Tray Guard Removed, or Magnetic Safety Switch

By-Passed.

ALWAYS Turn Off, Unplug From Power Source and Perform Lockout/Tagout Procedure to This

Machine BEFORE Attempting to Unjam or Unclog, Cleaning or Servicing.

NEVER Leave Machine Unattended While Operating.

NEVER Alter This Machine From its Original Form as Shipped From Factory. DO NOT Operate

Machine With Parts Missing.

PROMPTLY REPLACE Any Worn or Illegible Warning Labels.

USE ONLY BIRO Parts and Accessories Properly Installed.

INSTALLATION

TO AVOID SERIOUS PERSONAL INJURY

PROPERLY INSTALL EQUIPMENT IN ADEQUATE WORK AREA

ALWAYS Use Qualified Technician and Electrician for Installation.

ALWAYS Connect to Proper Voltage & Phase.

ALWAYS Install Equipment in Work Area with Adequate Light and Space Away From Children

and Visitors.

ONLY Operate on a Solid, Level, Non-Skid Surface.

NEVER Bypass, Alter, or Modify This Equipment in Any Way From Its Original Condition.

NEVER Operate With Tray And/Or Tray Guard Removed, or Magnetic Safety Switch By-Passed.

NEVER Operate Without all Warning Labels Attached and Owner/Operator Manual Available to

the Operator.

UNCRATING AND SET UP

1. Read this Manual thoroughly before installation and operation. Do not proceed with installation and operation if

you have any questions or do not understand anything in this Manual. Contact your local Distributor, or BIRO

first.

2. Install machine on a level, solid, non-skid surface in a well-lighted work area away from children and visitors.

3. After installing machine in operational area, it is imperative that the four adjusting legs be adjusted to level the machine and also eliminate rocking.

4. This machine is complete except for a knife and plate. There is a bowl shipping plug (stamped steel) placed in the output end of the grinding bowl to retain the grinding worm during shipment. REMOVE THE BOWL

SHIPPING PLUG AND THE GRINDING WORM.

5. After checking and making sure the power supply is correct, plug in your machine. NEVER OPERATE MACHINE WITHOUT TRAY AND GUARD INSTALLED (Machine will not run with tray removed).

6. Machine must be properly grounded. Use qualified electrician to install according to building codes.

MOTOR WIRING AND ELECTRICAL REQUIREMENTS

(A) Interchange of current is made in motor outlet box. Leads are properly marked. Changing instructions are

on the motor plate or motor outlet box.

(B) All grinders are wired 220 volts unless otherwise specified. Be sure motor specifications (voltage, cycle,

phase) match power supply line. Be sure line voltage is up to specification.

ALWAYS LEVEL MACHINE BEFORE USING

(D) Rated voltage of the unit shall be identical with full supply voltage.

(E) Voltage drop on the supply line shall not exceed 10% of full supply voltage. (F) The feederline conductor size in the raceway from the branch circuit to the unit must be correct to assure

adequate voltage under heavy starting and short overload conditions.

(G) The feederline conductor shall only be used for the supply of one unit of the relevant horsepower. For

connections of more than one unit on the same feederline, a local electrician will have to be consulted to determine the proper conductor size.

(H) The size of the electrical wiring required from the power source to the grinder on the 3, 5, 7

HP Grinders is

a MINIMUM OF No. 10 WIRE. On the 10 & 15 HP Grinders a MINIMUM OF No. 8 and No. 6 respectively.

(I) The BIRO Manufacturing Company is not responsible for permanent wiring, connection or installation.

MOTOR SPECIFICATIONS

HP KW VOLTS HZ PH AMPS

5 4 208/220 60 3 17/16 5 4 230 60 1 27 5 4 440 60 3 8 5 4 550 60 3 6.4

7.5 5.5 208/220 60 3 23/22

7.5 5.5 440 60 3 11 10 7.5 208/220 60 3 27/25.6 10 7.5 440 60 3 12.8 10 7.5 550 60 3 10 15 11 208/220 60 3 41/39 15 11 440 60 3 19.5

7. Located on the side of the machine is a toggle handle that activates the internal on/off switch. The interlock safety switch is mounted to the top of the internal switch and will break contact with the magnetic starter should the tray be removed.

8. Turn the toggle handle to the “ON” position. CHECK THE ROTATION OF THE WORM DRIVE SHAFT;

ROTATION MUST BE COUNTER-CLOCKWISE as indicated by the rotation decal affixed to the grinding bowl. ROTATION MUST ONLY BE CHECKED WITH THE GRINDING WORM REMOVED, otherwise serious

irreparable damage may occur to grinding components.

9. If machine runs clockwise (backwards), it must be rewired to correct rotation, otherwise serious irreparable damage may occur to grinding components.

10. Insert worm assembly into grinding bowl, place knife (sharp edges out) onto the square end of the worm assembly. The breaker plate slides over the worm knife drive pin, and is held from rotating by pins in the grinding bowl. Put on the retaining ring.

ONLY HAND TIGHTEN RETAINING RING

For best results, use knife and plate as a set. Do not operate machine for any period of time without product in the grinding bowl. This will cause heating and dulling of the knife and plate.

11. Check placement of all warning labels and Manual. Machine is now ready for trained operators to process product.

12. Use meat deflector attached to tray to eliminate meat splatter.

13. Contact your local Distributor or BIRO directly if you have any questions or problems with the installation or operation of this machine.

NOTE TO OWNER AND ELECTRICIAN: IF THIS MACHINE IS NOT CORD AND PLUG CONNECTED TO THE ELECTRICAL SUPPLY SOURCE, THEN IT SHOULD BE EQUIPPED WITH, OR CONNECTED TO, A LOCKABLE, MANUALLY-OPERATED DISCONNECT SWITCH (OSHA 1010.147).

+ 14 hidden pages