Bird-X SSA User Manual

SAFETY DATA SHEET
SPIKES SPECIAL ADHESIVE
1 / 19
Chicago, IL 60612
Product name : Spikes Special Ad h es ive Product code : SSA
Manufacturer or supplier's details Company name of supplier : Bird-X
Address : 300 N. Oakley Blvd.
Telephone : (312) 226-2473 Emergency telephone : AAPCC: 1(800)222-1222
Recommended use of the chemical and restrictions on use Recommended use : Adhesive, binding agents
SECTION 2. HAZARDS IDENTIFICATION
GHS Classification
Eye irritation : Category 2A Skin sensitization : Category 1
Specific target organ systemic toxicity - repeated exposure (Oral)
GHS Label element Hazard pictograms :
: C
Signal Word : Warning Hazard Statements : H317 May cause an allergic skin reaction.
Precautionary Statements : Prevention:
ategory 2 (Blood)
H319 Causes serious eye irritation. H373 May cause damage to organs (Blood) through prolonged or repeated exposure if swallowed.
P260 Do not breathe dust/ fume/ gas/ mist/ vapors/ spray. P264 Wash skin thoroughly after handling. P272 Contaminated work clothing must not be allowed out of
SAFETY DATA SHEET
SPIKES SPECIAL ADHESIVE
2 / 19
Chemical Name
CAS-No.
Concentration (%)
Silicon dioxide
7631-86-9
>= 5 - < 10
Methyltri(ethylmethylketoxime)silane
22984-54-9
>= 1 - < 5
Vinyltri (methylethylketoxime) silane
2224-33-1
>= 1 - < 5
N-(3-(Trimethoxysilyl)propyl)ethylenediamine
1760-24-3
>= 0.1 - < 1
Methyltri(ethylmethylketoxime)silane
isomers
and oligomers
Not Assigned
>= 0.1 - < 1
Other hazards None known.
SECTION 3.
Substance / Mixture : Mixture Chemical nature : Silicone
Hazardous ingredients
the
workplace. P280 Wear eye protection/ face protection. P280 Wear protective gloves.
Response:
P302 + P352 IF ON SKIN: Wash with plenty of soap and water. P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P314 Get medical advice/ attention if you feel unwell. P333 + P313 If skin irritation or rash occurs: Get medical advice/ attention. P337 + P313 If eye irritation persists: Get medical advice/ atten­tion. P363 Wash cont
Disposal:
P501 Dispose of contents/ container to an approved waste dis­posal plant.
COMPOSITION/INFORMATION
Sealant
aminated clothing before reuse.
ON INGREDIENTS
SECTION 4. FIRST AID MEASURES
General advice : In the case of accident or if you feel unwell, seek medical ad-
If inhaled : If inhaled, remove to fresh air.
In case of skin contact : In case of contact, immediately flush skin with soap and plenty
vice immediately. When symptoms persist or in all cases of doubt seek medical advice.
Get medical attention if symptoms occur.
of water. Remove contaminated clothing and shoes.
SAFETY DATA SHEET
SPIKES SPECIAL ADHESIVE
3 / 19
In case of eye contact : In case of contact, immediately flush eyes with plenty of water
If swallowed : If swallowed, DO NOT induce vomiting.
Most important symptoms and effects, both acute and delayed
Protection of first-aiders : First Aid responders should pay attention to self-protection,
: May cause an allergic skin reaction.
Notes to physician : Treat symptomatically and supportively.
SECTION 5. FIRE-FIGHTING MEASURES
Suitable extinguishing media : Water spray
Unsuitable extinguishing media
: N
Get medical Wash clothing before reuse. Thoroughly clean shoes before reuse.
for at least 15 minutes. If easy to do, remove contact lens, if worn. Get medical attention.
Get medical attention if symptoms occur. Rinse mouth thoroughly with water.
Causes serious eye irritation. May cau exposure if swallowed.
and use the recommended personal protective equipment when the potential for exposure exists.
Alcohol-resistant
chemical
Dry Carbon dioxide
one known.
attention.
se damage to organs through prolonged or repeated
foam
(CO2)
Specific hazards during fire fighting
Hazardous combustion prod­ucts
Specific extinguishing meth­ods
Special protective equipment for fire-fighters
: Exposure to combustion products may be a hazard to health.
: Carbon oxides Silicon
oxides Formaldehyde Nitrogen oxides (NOx)
: Use extinguishing measures that are appropriate to local cir-
cumstances and the surrounding environment. Use water spray to cool unopened containers. Remove undamaged containers from fire area if it is safe to do so. Evacuate area.
: In the event of
Use personal protective equipment.
fire, wear self-contained breathing apparatus.
SAFETY DATA SHEET
SPIKES SPECIAL ADHESIVE
4 / 19
SECTION 6. ACCIDENTAL RELEASE MEASURES
Personal precautions, protec­tive equipment and emer­gency procedures
Environmental precautions : Discharge into the environment must be avoided.
ds and materials for
Metho containment and cleaning up
: Use personal protective equipment.
Follow safe handling advice and personal protective equip­ment recommendations.
Prevent further leakage or spillage if safe to do so. Retain and dispose of contaminated wash water. Local authorities should be advised if significant spillages cannot be contained.
: Soak up with inert absorbent material.
For large spills, provide diking or other appropriate contain­ment to keep material from spreading. If diked material can be pumped, store recovered material in appropriate container. Clean up remaining materials from spill with suitable absor­bent. Local or national regulations may apply to releases and dis­posal of this material, as well as those materials and items employed in the cleanup of releases. You will need to deter­mine which regulations are applicable. Sectio
ns 13 and 15 of this SDS provide information regarding
certain local or national requirements.
SECTION 7. HANDLING AND STORAGE
Technical measures : See Engineering measures under EXPOSURE
CONTROLS/PERSONAL PROTECTION section.
Local/Total ventilation : Use only with adequate ventilation. Advice on safe handling : Do not get on skin or clothing.
Do not Do not get in Handle in accordance with good industrial hygiene and safety practice. Keep away from water. Protect from moisture. Take care to prevent spills, waste and minimize relea environment.
Conditions for safe storage : Keep in properly labeled containers.
Store in accordance with the particular national regulations.
Materials to avoid : Do not store with the following product types:
Strong oxidizing agents
swallow.
eyes.
se to the
SAFETY DATA SHEET
SPIKES SPECIAL ADHESIVE
5 / 19
Ingredients
CAS-No.
Value type exposure)
Control parame­concentration
Basis
Silicon dioxide
7631-86-9
TWA (Dust)
20 Million
(Silica)
OSHA Z-3 TWA (Dust)
80 mg/m3
OSHA Z-3 TWA
6 mg/m3 (Silica)
NIOSH REL Ingredients
CAS-No.
Methyltri(ethylmethylketoxime) silane
22984-54-9
Vinyltri (methylethylketoxime) silane
2224-33-1
N-(3­ediamine
1760-24-3 Methyltri(ethylmethylketoxime) silane isomers and oligomers
Not Assigned
Ingredients
CAS-No.
Value type exposure)
Control parame­concentration
Basis
Ethyl methyl ketoxime
96-29-7
TWA
10 ppm
DCC OEL
Further information: Skin sensitization
TWA
10 ppm
US WEEL
SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Ingredients with workplace control parameters
Hazardous components without workplace control parameters
(Trimethoxysilyl)propyl)ethylen
Occupational exposure limits of decomposition products
(Form of
ters / Permissible
particles per cubic foot
/ %SiO2 (Silica)
Engineering measures : Processing may form hazardous compounds (see section
Personal protective equipment
Respiratory protection : General and local exhaust ventilation is recommended to
10).
(Form of
ters / Permissible
Ensure adequate ventilation, especially in confined areas. Minimize workplace exposure concentrations.
maintain vapor exposures below recommended limits. Where concentrations are above recommended limits or are unknown, appropriate respiratory protection should be worn. Follow OSHA respirator regulations (29 CFR 1910.134) and use NIOSH/MSHA approved respirators. Protection provided by air purifying respirators against exposure to any hazardo
us chemical is limited. Use a positive pressure air
supplied respirator if there is any potential for uncontrolled
SAFETY DATA SHEET
SPIKES SPECIAL ADHESIVE
6 / 19
release, exposure levels are unknown, or any other circumstance where air purifying respirators may not provide adequate protection.
Hand protection
Material : Impervious gloves
Remarks : Choose gloves to protect hands against chemicals depending
on the concentration specific to place of work. Breakthrough time is not determined for the product. Change gloves often! For special applications, we recommend clarifying the resistance to chemicals of the aforementioned protective gloves with the glove manufacturer. Wash hands before breaks and at the end of workday.
Eye protection : Wear the following personal protective equipment:
Safety goggles
Skin and body protection : Select appropriate protective clothing based on chemical
resistance data and an assessment of the local exposure potential. Skin contact must be avoided by using impervious protective clothing (gloves, aprons, boots, etc).
Hygiene measures : Ensure that eye flushing systems and safety showers are
located close to the working place. When using do not eat, drink or smoke. Wash contaminated clothing before re-use.
se precautions are for room temperature handling. Use at
The elevated temperature or aerosol/spray applications may re-
SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance : paste
quire added precautions.
Color : colorless Odor : slight Odor Threshold : No data available pH : Not applicable Melting point/freezing point : No data available
Initial boiling point and boiling range
Flash point : Not applicable
: Not applicable
SAFETY DATA SHEET
SPIKES SPECIAL ADHESIVE
7 / 19
Evaporation rate : Not applicable Flammability (solid, gas) : Not classified as a flammability hazard Upper explosion limit : No data available Lower explosion limit : No data available Vapor pressure : Not applicable Relative vapor density : No data available Relative density : 1.04
Solubility(ies)
Water solubility : No data available
Partition coefficient: n­octanol/water
Autoignition temperature : No data available
: No data available
Decomposition temperature : No data available Viscosity
Viscosity, dynamic : Not
applicable Explosive properties : Not explosive Oxidizing properties : The substance or mixture is not classified as oxidizing. Molecular weight : No data available
SECTION 10. STABILITY AND REACTIVITY
Reactivity : Not classified as a reactivity hazard. Chemical stability : Stable under normal conditions.
Possibility of hazardous reac­tions
Conditions to avoid : Exposure to moisture. Incompatible materials : Oxidizing agents
: Use at elevated temperatures may form highly hazardous
compounds. Can react with strong oxidizing agents. Hazardo contact with water or humid air. Hazardous decomposition products will be formed at elevated temperatures.
Water
us decomposition products will be formed upon
SAFETY DATA SHEET
SPIKES SPECIAL ADHESIVE
8 / 19
Hazardous decomposition products
Contact with water or hu-
SECTION 11. TOXICOLOGICAL INFORMATION
mid air Thermal decomposition : Formaldehyde
Information on likely routes of exposure Skin contact Ingestion Eye contact
Acute toxicity Not classified based on available information.
Product: Acute oral toxicity : Acute toxicity estimate: > 5,000 mg/kg
Ingredients: Silicon dioxide:
Acute oral toxicity : LD50 (Rat): > 3,300 mg/kg
: Ethyl methyl ketoxime
Method: Calculation
Assessment: The substance or mixture has no acute oral tox­icity Remarks: Information taken from reference works and the literature.
Acute inhalation toxicity : LC50 (Rat): > 2.08 mg/l
Exposure time: 4 h Test atmosphere: Assessment: The substance or mixture has no acute inhala­tion toxicity Remarks: Information taken from reference works and the literature.
Acute dermal toxicity : LD50 (Rabbit): > 5,000 mg/kg
Assessment: The substance or mixture has no acute dermal toxicity Remarks: Informat literature.
Methyltri(ethylmethylketoxime)silane: Acute oral toxicity : LD50 (Rat): > 2,520 mg/kg
Assessment: The substance or mixture has no acute oral tox­icity Remarks: Based on test
Vinyltri (methylethylketoxime) silane: Acute oral toxicity : LD50 (Rat): > 2,000 mg/kg
Assessment: The substance or mixture has no acute oral tox-
method
dust/mist
ion taken from reference works and the
data
SAFETY DATA SHEET
SPIKES SPECIAL ADHESIVE
9 / 19
icity Remarks: Based on test
data
Acute dermal toxicity : LD50 (Rat): > 2,000 mg/kg
Assessment: The substance or mixture has no acute dermal toxicity
data
Remarks: Based on test
N-(3-(Trimethoxysilyl)propyl)ethylenediamine: Acute oral toxicity : LD50 (Rat): 2,295 mg/kg
data
Remarks: Based on test
Acute inhalation toxicity : LC50 (Rat): > 1.49 mg/l
Exposure time: 4 Test atmosphere: Remarks: Based on test
h
dust/mist
data
Acute dermal toxicity : LD50 (Rabbit): > 2,000 mg/kg
essment: The substance or mixture has no acute dermal
Ass toxicity
Skin corrosion/irritation Not classified based on available information.
Ingredients: Silicon dioxide:
Result: No skin irritation Remarks: Information taken from reference works and the literature.
Remarks: Based on test
data
Methyltri(ethylmethylketoxime)silane: Species: Rabbit Result: No skin irritation Remarks: Based on data from similar materials
N-(3-(Trimethoxysilyl)propyl)ethylenediamine: Species: Rabbit Result: Mild skin irritation Remarks: Based on test data
Serious eye damage/eye irritation Causes serious eye irritation.
Ingredients: Silicon dioxide:
Result: No eye irritation Remarks: Information taken from reference works and the literature.
Methyltri(ethylmethylketoxime)silane: Species: Rabbit Result: Irritation to eyes, reversing within 7 days Remarks: Based on test data
SAFETY DATA SHEET
SPIKES SPECIAL ADHESIVE
10 / 19
Vinyltri (methylethylketoxime) silane: Species: Rabbit Result: Irreversible effects on the eye Remarks: Based on test data
N-(3-(Trimethoxysilyl)propyl)ethylenediamine: Species: Rabbit Result: Irreversible effects on the eye Remarks: Based on test data
Methyltri(ethylmethylketoxime)silane
Species: Rabbit Result: Irritation to eyes, reversing within 7 days Remarks: Based on data from similar materials
Respiratory or skin sensitization Skin sensitization: May cause an allergic skin reaction.
Respiratory sensitization: Not class
Ingredients: Silicon dioxide:
Assessment: Does not cause skin sensitization. Test Type: Skin: test type not specified
Species: Guinea pig Remarks: No known sensitising effect. Information taken from reference works and the literature.
isomers and oligomers:
ified based on available information.
Methyltri(ethylmethylketoxime)silane: Assessment: Probability or evidence of skin sensitization in humans
Test Type: Maximization Test (GPMT) Species: Guinea pig Remarks: Based on test data
Vinyltri (methylethylketoxime) silane: Assessment: Probability or evidence of skin sensitization in humans
Test Type: Maximization Test (GPMT) Species: Guinea pig Remarks: Causes sensitization. Based on data from similar materials
N-(3-(Trimethoxysilyl)propyl)ethylenediamine: Assessment: Probability or evidence of skin sensitization in humans
Test Type: Maximization Test (GPMT) Species: Guinea pig Remarks: Causes sensitization. Information taken from reference works and the literature.
Methyltri(ethylmethylketoxime)silane
Assessment: Probability or evidence of skin sensitization in humans
isomers and oligomers:
SAFETY DATA SHEET
SPIKES SPECIAL ADHESIVE
11 / 19
Test Type: Maximization Test (GPMT) Species: Guinea pig Remarks: Causes sensitization. Based on data from similar materials
Germ cell mutagenicity Not classified based on available information.
Ingredients: Silicon dioxide:
Genotoxicity in vitro : Result: negative
Remarks: Information taken from reference works and the literature.
Genotoxicity in vivo : Application Route: Ingestion
Result: Remarks: Information taken from reference works and the literature.
Germ cell mutagenicity ­Assessment
Methyltri(ethylmethylketoxime)silane: Genotoxicity in vitro : Test Type: Mutagenicity (in vitro mammalian cytogenetic test)
: Animal testing did not show any mutagenic effects.
Result: negative Remarks: Based on test
negative
data
Vinyltri (methylethylketoxime) silane: Genotoxicity in vitro : Test Type: Bacterial reverse mutation assay (AMES)
Result: negative
data
Remarks: Based on test
Genotoxicity in vivo : Test Type: In vivo micronucleus test
Mouse
Species: Application Route: Intraperitoneal injection Result: Remarks: Based on test
Germ cell mutagenicity ­Assessment
Carcinogenicity Not classified based on available information.
IARC No ingredient of this product present at levels greater than or
: Animal testing did not show any mutagenic effects.
equal to 0.1% is identified as probable, possible or confirmed human carcinogen by IARC.
negative
data
OSHA No ingredient of this product present at levels greater than or
equal to 0.1% is identified as a carcinogen or potential carcino­gen by OSHA.
SAFETY DATA SHEET
SPIKES SPECIAL ADHESIVE
12 / 19
NTP No ingredient of this product present at levels greater than or
equal to 0.1% is identified as a known or anticipated carcinogen by NTP.
Reproductive toxicity Not classified based on available information.
Ingredients: Methyltri(ethylmethylketoxime)silane:
Effects on fertility : Test Type: Combined repeated dose toxicity study with the
reproduction/developmental
toxicity screening test Species: Rat, male and female Application Route: Ingestion Symptoms: No effects on fertility. Remarks: Based on test data
Effects on fetal development : Test Type: Combined repeated dose toxicity study with the
reproduction/developmental
toxicity screening test Species: Rat, male and female Application Route:
Ingestion Symptoms: No effects on fetal development. Remarks: Based on test data
Reproductive toxicity - As­sessment
: No eviden
ce of adverse effects on sexual function and fertility,
or on development, based on animal experiments.
N-(3-(Trimethoxysilyl)propyl)ethylenediamine: Effects on fertility : Test Type: Combined repeated dose toxicity study with the
reproduction/developmental
toxicity screening test Application Route: Ingestion Symptoms: No effects on fertility. Remarks: Based on test data
Effects on fetal development : Test Type: Combined repeated dose toxicity study with the
reproduction/developmental Application Route: Ingestion Symptoms: No effects on Remarks: Based on test data
Reproductive toxicity - As­sessment
: No evidence of adverse effects on sexual function and fertility,
or on development, based on animal experiments.
STOT-single exposure Not classified based on available information.
STOT-repeated exposure May cause damage to organs (Blood) through prolonged or repeated exposure if swallowed.
Ingredients: Methyltri(ethylmethylketoxime)silane:
Routes of exposure: Ingestion Target Organs: Blood Assessment: Shown to produce significant health effects in animals at concentrations of >10 to
toxicity screening test
fetal development.
SAFETY DATA SHEET
SPIKES SPECIAL ADHESIVE
13 / 19
100 mg/kg bw. Vinyltri (methylethylketoxime) silane:
Routes of exposure: Ingestion Target Organs: Blood Assessment: Shown to produce significant health effects in animals at concentrations of >10 to 100 mg/kg bw.
N-(3-(Trimethoxysilyl)propyl)ethylenediamine: Routes of exposure: Ingestion Assessment: No significant health effects observed in animals at concentrations of 100 mg/kg bw or less.
Methyltri(ethylmethylketoxime)silane
Routes of exposure: Ingestion Target Organs: Blood Assessment: Shown to produce significant health effects in animals at concentrations of >10 to 100 mg/kg bw.
Repeated dose toxicity Ingredients:
Methyltri(ethylmethylketoxime)silane:
Species: Rat Application Route: Ingestion Target Organs: Blood Remarks: Based on test data
isomers and oligomers:
Vinyltri (methylethylketoxime) silane:
Species: Rat Application Route: Ingestion Target Organs: Blood Remarks: Based on data from similar materials
N-(3-(Trimethoxysilyl)propyl)ethylenediamine: Application Route: Ingestion Remarks: Based on test data
Methyltri(ethylmethylketoxime)silane
Species: Rat Application Route: Ingestion Target Organs: Blood Remarks: Based on data from similar materials
Aspiration toxicity Not classified based on available information.
Further information Product:
Remarks: During use of the material, small amounts of methylethylketoxime (MEKO) will be re­leased. Rodents exposed to chronic MEKO inhalation throughout their lifetimes showed signifi­cant increases in liver tumor rates.
isomers and oligomers:
SAFETY DATA SHEET
SPIKES SPECIAL ADHESIVE
14 / 19
SECTION 12. ECOLOGICAL INFORMATION
Ecotoxicity Ingredients:
Methyltri(ethylmethylketoxime)silane:
Toxicity to fish : LC50 (Oncorhynchus mykiss (rainbow trout)): > 120 mg/l
Exposure time: 96 Method: OECD Test Guideline 203 Remarks: Based on data from similar materials
Toxicity to daphnia and other aquatic invertebrates
Toxicity to algae : ErC50 (Selenastrum capricornutum (green algae)): 94 mg/l
: EC50 (Daphnia magna (Water flea)): > 120
Exposure time: 48 h Method: OECD Test Guideline 202 Remarks: Based on data from similar materials
Exposure time: 72 Method: OECD Test Guideline 201 Remarks: Based on data from similar materials
Ecotoxicology Assessment Acute aquatic toxicity : This product has no known ecotoxicological effects.
N-(3-(Trimethoxysilyl)propyl)ethylenediamine: Toxicity to fish : LC50 (Danio rerio (zebra fish)): 597 mg/l
Exposure time: 96 Method: Directive 67/548/EEC, Annex V, C.1.
Toxicity to daphnia and other aquatic invertebrates
Toxicity to algae : ErC50 (Selenastrum capricornutum (green algae)): 8.8 mg/l
: EC50 (Daphnia sp.): 81 mg/l
Exposure time: 48 h Method: Directive 67/548/EEC, Annex V, C.2.
Exposure time: 72 Metho
NOEC (Selenastrum capricornutum (green algae)): 3.1 mg/l Exposure time: 72 Method: OECD Test Guideline 201
Toxicity to daphnia and other aquatic invertebrates (Chronic toxicity)
Toxicity to bacteria : EC50 (Pseudomonas putida): 67 mg/l
: NOEC (Daphnia sp.): > 1 mg/l
Exposure time: 21 d
Exposure time: 16 Test Type: Growth Method: DIN 38 412 Part
h
h
h
h
d: OECD Test Guideline 201
h
h
inhibition
8
mg/l
SAFETY DATA SHEET
SPIKES SPECIAL ADHESIVE
15 / 19
Persistence and degradability Ingredients:
Methyltri(ethylmethylketoxime)silane:
Biodegradability : Result: Not readily biodegradable.
Biodegradation: 14.5 % Exposure time: 21 d Method: OECD Test Guideline 302B Remarks: Based on data from similar materials
Vinyltri (methylethylketoxime) silane: Biodegradability : Result: Not readily biodegradable.
Stability in water : Degradation half life: 1 s N-(3-(Trimethoxysilyl)propyl)ethylenediamine:
Biodegradability : Result: Not readily biodegradable.
Biodegradation: 39 Method: OECD Test Guideline 301A
Stability in water : Degradation half life: 0.025 h (24.7 °C) pH: 7
Metho
Bioaccumulative potential Ingredients:
Methyltri(ethylmethylketoxime)silane:
Partition coefficient: n-
: log Pow: 11.2
octanol/water
N-(3-(Trimethoxysilyl)propyl)ethylenediamine:
Partition coefficient: n­octanol/water
: log Pow: -0.3
Mobility in soil No data available
Other adverse effects No data available
SECTION 13. DISPOSAL CONSIDERATIONS
Disposal methods
Resource Conservation and Recovery Act (RCRA)
Waste from residues : Dispose of in accordance with local regulations. Contaminated packaging : Dispose of as unused product.
: This product has been evaluated for RCRA characteristics
and does not meet the criteria of hazardous waste if discarded in its purchased form.
Empty containers should be taken to an approved waste han-
%
d: OECD Test Guideline 111
SAFETY DATA SHEET
SPIKES SPECIAL ADHESIVE
16 / 19
(lbs)
(lbs)
n-Hexane
110-54-3
5000 *
Methanol
67-56-1
5000 *
Ethylenediamine
107-15-3
5000 *
(lbs)
(lbs)
Ethylenediamine
107-15-3
5000 *
dling site for recycling or disposal.
SECTION 14. TRANSPORT INFORMATION
International Regulation UNRTDG
Not regulated as a dangerous good IATA-DGR
Not regulated as a dangerous good IMDG-Code
Not regulated as a dangerous good Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
Not applicable for product as supplied.
Domestic regulation 49 CFR
Not regulated as a dangerous good
SECTION 15. REGULATORY
EPCRA - Emergency Planning and Community Right-to-Know CERCLA Reportable Quantity
Ingredients CAS-No. Component RQ
INFORMATION
Calculated product RQ
*: Calculated RQ exceeds reasonably attainable upper limit.
SARA 304 Extremely Hazardous Substances Reportable Quantity
Ingredients CAS-No. Component RQ
*: Calculated RQ exceeds reasonably attainable upper limit.
SARA 311/312 Hazards : Acute Health Hazard
SARA 302 : No chemicals in this material are subject to the reporting
SARA 313 : This material does not contain any chemical components with
Calculated product RQ
Chronic Health
Hazard
requirements of SARA Title III, Section 302.
known CAS numbers that exceed the threshold (De Minimis) reporting levels established by SARA Title III, Section 313.
SAFETY DATA SHEET
SPIKES SPECIAL ADHESIVE
17 / 19
Dimethyl siloxane, hydroxy-terminated
70131-67-8
70 - 90 %
Silicon dioxide
7631-86-9
5 - 10 %
Methyltri(ethylmethylketoxime)silane
22984-54-9
1 - 5 %
Dimethyl siloxane, hydroxy-terminated
70131-67-8
70 - 90 %
Silicon dioxide
7631-86-9
5 - 10 %
Methyltri(ethylmethylketoxime)silane
22984-54-9
1 - 5 %
Vinyltri (methylethylketoxime) silane
2224-33-1
1 - 5 %
US State Regulations Pennsylvania Right To Know
New Jersey Right To Know
California Prop 65 WARNING: This product contains a chemical known in the
Methanol 67-56-1
The ingredients of this product are reported in the following inventories: NZIoC : All ingredients listed or exempt.
State of California to cause birth defects or other reproductive harm.
TSCA : All chemical substances in this material are included on or
exempted from listing on the TSCA Inventory of Chemical Substances.
AICS : All ingredients listed or exempt. IECSC : All ingredients listed or exempt. ENCS/ISHL : All components are listed on ENCS/ISHL or exempted from
inventory listing.
KECI : All ingredients listed, exempt or notified. PICCS : All ingredients listed or exempt. DSL : All chemical substances in this product comply with the CEPA
Inventories AICS (Australia), DSL (Canada), IECSC (China), REACH (European Union), ENCS (Japan),
ISHL (Japan), KECI (Korea), NZIoC (New Zealand), PICCS (Philippines), TCSI (Taiwan), TSCA (USA)
1999 and NSNR and are on or exempt from listing on the Canadian Domestic Substances List (DSL).
SAFETY DATA SHEET
SPIKES SPECIAL ADHESIVE
18 / 19
Instability
Health
SECTION 16. OTHER INFORMATION
Further information
NFPA: HMIS III:
Flammability
2
Special hazard.
Full text of other abbreviations DCC OEL : Dow Corning Guide
NIOSH REL : USA. NIOSH Recommended Exposure Limits OSHA Z-3 : USA. Occupational Exposure Limits (OSHA) - Table Z-3 Min-
US WEEL : USA. Workplace Environmental Exposure Levels (WEEL) DCC OEL / TWA : Time weighted average NIOSH REL / TWA
OSHA Z-3 / TWA : 8-hour time weighted average US WEEL / TWA : 8-hr TWA
Sources of key data used to compile the Material Safety Data Sheet
Revision Date : 04/04/2015
Items where changes have been made to the previous version are highlighted in the body of this document by two vertical lines.
The information provided in this Safety Data Sheet is correct to the best of our knowledge, in­formation and belief at the date of its publication. The information is designed only as a guid­ance for safe handling, use, processing, storage, transportation, disposal and release
not be considered a warranty or quality specification of any type. The information pro-
shall vided relates only to the specific material identified at the top of this SDS and may not be valid when the SDS material is used in combination with any other materials or less specified in the text. Material users should review the information and recommendations in the specific cont cluding an assessment of the appropriateness of the SDS material in the user’s end product, if applicable.
0
: Time-weighted average concentration for up to a 10-hour
ext of their intended manner of handling, use, processing and storage, in-
HEALTH FLAMMABILITY
PHYSICAL HAZARD
0 = not significant, 1 =Slight, 2 = Moderate, 3 = High 4 = Extreme, * = Chronic
eral Dusts
workday during a 40-hour workweek
: Internal technical data, data from raw material SDSs, OECD
eChem Portal search results and European Chemicals Agen­cy, http://echa.europa.eu/
in any process
2* 1 0
and
, un-
SAFETY DATA SHEET
SPIKES SPECIAL ADHESIVE
19 / 19
US / Z8
Loading...