Birchwood Lighting VANESSA CM INSTRUCTION SHEET

VANESSA CM

Ceiling Mounting
Stand-Alone

INSTRUCTION SHEET

BRACKET MOUNTING CENTERS

NOMINALFIXTURE LENGTH

X

1/2 X

C

L

NOMINAL FIXTURE LENGTH X

2’ 16”

3’ 24”

4’ 32”

C

L

DRILL HOLE IN CEILING
*SEE NOTE (2)

E

STND - Standard Feed

Mounting

1. Install ceiling brackets (A) as
shown using 1/4” bolts (by others)
suitable for intended surface.

2. Drill hole in ceiling as shown
for ex conduit. Note: size of
hole depends on size of conduit
connector and must be large
enough to allow conduit connector
to protrude into ceiling.

3. Loosen captive screws (B) and
remove end plates (C) from both
ends.

1.25”

FIXTURE

1.5”

AA

4. Remove reector/liner.

4”

HEIGHT

5. Connect 1/2” ex conduit to
xture. Note: for wet locations ex

conduit must be liquid tight and

pipe thread sealant or teon tape

must be used on threads.

6. Mount xture on ceiling brackets

(A) and install supplied screws (D).

7. Make wire connections inside

xture.

WET LOCATION CONDUIT

(BY OTHERS)

1/2” TRADE SIZE WET

LOCATION CONNECTOR

(BY OTHERS)

D

B

C

Note: To be installed by a qualied electrician per N.E.C. and all local codes.

Birchwood Lighting • 3340 E. La Palma Avenue • Anaheim, CA 92806 • 714.550.7118 fax [phone]

104

8. Reinstall reector/liner

9. Reinstall lens. Note: rmly press

along entire length of lens to ensure
a good seal.

10. Reinstall both end plates (C).

D

11. Seal hole around conduit
connector with silicone, caulking or
wall patch.

note: To remove lens, lift from end

using a at blade screw driver(E)

to pry loose. Note: take care not to
damage lens or gasket.

Continuous run, provide for 1/8”

between xtures.

820-00032

V-0520

VANESSA CM

Ceiling Mounting
Stand-Alone

INSTRUCTION SHEET

BRACKET MOUNTING CENTERS

NOMINALFIXTURE LENGTH

X

C

L

C

L

NOMINAL FIXTURE LENGTH X

2’ 16”

3’ 24”

4’ 32”

WET LOCATION CONDUIT (BY OTHERS)

1/2” TRADE SIZE WET LOCATION CONNECTOR

(BY OTHERS)

End Feeds - EFR | EFL | EF2

Mounting

1. Install ceiling brackets (A) as
shown using 1/4” bolts (by others)
suitable for intended surface.

2. Loosen captive screws (B) and
remove endplates (C) from both
ends.

4. Remove reector/liner.

5. Mount xture on ceiling brackets

(A) and install supplied screws (D).

1.25”
4”

FIXTURE

1.5”
HEIGHT

AA

E

6. Connect 1/2” ex conduit to
xture. *Note: for wet locations ex

conduit must be liquid tight and

pipe thread sealant or teon tape

must be used on threads.

7. Make wire connections inside

xture.

8. Reinstall reector/ liner

9. Reinstall lens. Note: rmly press

along entire length of lens to ensure
a good seal.

10. Reinstall both endplates (C).

B

D

C

FEED TYPES

EFR - END FEED RIGHT EF2 - END FEED BOTH ENDS

EFL - END FEED LEFT

Note: To be installed by a qualied electrician per N.E.C. and all local codes.

Birchwood Lighting • 3340 E. La Palma Avenue • Anaheim, CA 92806

714.550.7118 fax [phone]

105

note: To remove lens, lift from end

using a at blade screw driver(E)

to pry loose. Note: take care not to

D

damage lens or gasket.

Continuous run, provide for 1/8”

between xtures.

820-00030

Due to a program of continuous improvement instructions

© 2018 Birchwood Lighting, Inc. All rights reserved.

are subject to change without notice.

V-0520