Page 1
Installation Guide
ToolsRequired: Flatheadscrewdriver, Phillipsscrewdriver,pliers,wire cutters,wire strippers,electricaltape, safetyglasses.
LightSource:
FixtureHangingHeight:
EstimatedAssembly Time:
Preparation:
present.Ifany partsare missingordamaged, donot attempttoassemble, install,or operatethefixture. Contactyour originalplaceof purchase.
Note: This CONVERTIBLE fixture can be mounted as pendant light or semi-flush light. Refer to respective
installation steps for installations.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
(6)B10Candelabra Basebulbs 60WMaximum,bulb notincluded.
MinimumHangingHeight is13.5”, MaximumHangingHeight is53.5”.
30-45minutes
Identifyandinspect allparts beforebeginninginstallation. Checkpackage contentlistand diagramsbelow toensureall partsare
Package Contents
Crossbar Assembly
A
x1
6” Rod
B
x2
12” Rod
C
x2
Assembly Instructions for Pendant Light
(Step 1A - Step 6A)
STEP 1A - Install Ceiling Canopy, Rods
and Fixture Body together
a. Determine the Rods (B/C) to be
assembled to the Fixture Body (E)
according to your hanging height.
b. Pass the supply wires and ground wire
through the chosen rods (B/C) and the
Ceiling Canopy (D). Thread the Fixture
Body (E), the chosen Rods (B/C) and the
Ceiling Canopy (D) together. Hand
tighten until snug.
Ceiling Canopy
D
x1
Fixture Body
E
x1
B
STEP 2A - Installing the Crossbar Assembly
A. Pass the supply wires from outlet box through the Crossbar
Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box
with the head of the Green Ground Screw facing you. Secure the
Crossbar Assembly (A) with Outlet Box Screws (not included).
Tighten until snug.
Outlet Box Screws
(not included)
Figure 2A
STEP 3A Test Fitting Ceiling Canopy to Crossbar Assembly-
D
A.
Remove mounting balls from the Crossbar Assembly (A). Fit the
eiling Canopy to the
C (D) Crossbar Assembly (A) and secure with
mounting balls. Note: The should be snug
against the and the mounting balls. If
B
of the nipple on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the Ceiling Canopy (D) is secure, remove the
mounting ball and Ceiling Canopy (D) and proceed to Step 4A.
ceiling
Ceiling Canopy (D)
Outlet Box
A
Supply Wires with
Ground Wire
not, adjust the length
Suggested rods for Ceiling height :
8’ ceiling : use (1) 6” rods and (1) 12” rods
9’ ceiling : use (1) 6” rods and (2) 12” rods
Supply Wires
and Ground Wire
E
C
C
Figure 1A
1of2
Mounting Screw
Mounting Ball
A
D
Hex Nut and
Lock Washer
Figure 3A
Page 2
STEP 4A - Wire Connections
Wrap bare or green ground wire around green ground screw on the
A.
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Assembly Instructions for Semi-Flush Light
(Step 1B)
The following parts will not be used in the assembly of the SemiFlush Light fixture. Please set aside these parts.
B
6” Rod
x2
C
12” Rod
x2
(Extra Parts include)
White wire
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
Green Ground Screw
on the Crossbar
STEP 5A Install the Fixture-
A. Carefully tuck all wires into the outlet box and position the Ceiling
Canopy (D) over the outlet box. Align the holes in the ceiling canopy
with the mounting screws, then attach the Ceiling Canopy (D) using
the previously removed mounting balls. Hand tighten until snug.
Mounting Screw
A
D
White wire
from fixture
Black wire
from fixture
Ground wire
from Fixture
Figure 4A
Hex Nut and
Lock Washer
STEP 1 - Install Ceiling Canopy and Fixture Body together
A. Pass the supply wires and ground wire through the Ceiling Canopy
(D). Thread the Fixture Body (E) and the Ceiling Canopy (D)
together. Hand tighten until snug.
approximately 6” of wire extending from the ceiling canopy.
. Go to Step A Step A to complete installations.-
B26
Supply Wires
and Ground Wire
Cut the wires leaving
D
E
Figure 1B
Mounting Ball
Figure 5A
STEP 6A Install Bulbs-
A. Insert bulbs onto sockets and screw snugly into place.
Your fixture is now assembled and ready to use. Enjoy!
Bulb(not included)
Socket
Figure 6A
2of2
Loading...