1
Wall mounting Ceiling mounting
2
When not mounted When already mounted
3
5
4
* The device must only be operated at a protective low voltage with safe electrical insulation. Product repairs must be performed solely by the manufacturer.
* Shut off all power going to the sensor before attempting any wiring procedures.
* Maintain a clean & safe environment when working in public areas.
* Constantly be aware of pedestrian traffic around the door area.
* Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door.
* Always check placement of all wiring and components before powering up to ensure that moving door parts will not catch any wires and cause damage to equipment.
* Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of installation.
Safety instructions
Microwave motion detector for automatic pedestrian doors [ES with direction recognition] Questions? Call us at 800 - 252-1272, 8am - 5pm central standard time.
DO NOT LEAVE ANY PROBLEMS UNRESOLVED - NEVER SACRIFICE SAFETY FOR ANY REASON
Impulse
Open sensor with a screwdriver
Drill holes using template
Install sensor with provided screws
Connections
Testing of the settings
1
motion
sensing the future
Side cable exit as shown on the left or
front cable exit as shown below
1) Remove provided screws for installation.
white
1
brown
2
green
3
yellow
4
grey
5
- ~12-36 V DC
+ ~12-28 V AC
Common
Normally open
Normally closed
48 V AC / DC
24 W / 55 VA
2)
1. Turn on power and allow detector
to self-tune
2. Stay outside the detection zone
for 5 seconds
Test the size and position of the
sensing eld
7
10
9
Value for mounting height of 7' 3" (2.2 m) . Maximum mounting height: 13' 1" (4 m).
Avoid rain exposure
Avoid moving objects
in sensing field
Avoid vibrations
Avoid proximity to
fluorescent lights
If after troubleshooting a problem, a satisfactory solution cannot be achieved,
please call
Bircher Reglomat at 800 - 252-1272
from 8am - 5pm central standard time.
You may also visit our website at www.bircherreglomat.com
DO NOT LEAVE ANY PROBLEMS UNRESOLVED
NEVER SACRIFICE SAFETY FOR ANY REASON
Technical data
2
Contact
Bircher Reglomat reserves the right to change any information on this document
without notice.
For the latest version, please log on to www.bircherreglomat.com
or call us at 847-952-3730 to request a copy of the current version.
Disclaimer
K6202.029 08/06 Bircher Reglomat reserves the right to change any information on this document without notice.
Power supply
Current consumption
Temp. range
Humidity
Microwave module
Transmitting power
Relay output pot. free
Switching voltage
Switching current
Switching power
Protection class
Housing material
6
8
11
12
13
Interference avoidance
Setting all other parameters
Setting frontal inclination
Setting sensing field shape and size
Setting field shape and position
12-28 V AC / 12-36 V DC
approx. 100 mA at 24 V AC,
+20° C
-4 °F to +140 °F [
-20° C to +60° C]
0 to 90%, non condensing
K-band 24,125 GHz +/ 100 MHz
≤
20 dBm
change-over contact
48 V AC/DC
0.5 A AC/1 A DC
55 VA / 24 W
suitable for the application after IP 54
ABS
Open position / narrow eld
Fig. 6.1 Fig. 6.2 Fig. 6.3
Adjustable antenna
Open position (see g. 6.1)
Sensitivity potentiometer
Minimum
eld dimensions
3’ 3" x 1' 8" (1.0 x 0.5 m)
Maximum eld dimensions
8' 2" x 8' 2" (2.5 x 2.5 m)
Closed position / wide eld
Adjustable antenna
Closed position (see g.6.2)
Sensitivity potentiometer
Minimum
4' 11" x 3' 3" (1.5 x 1.0 m)
Maximum eld dimensions
11' 6" x 6' 7" ( 3.5 x 2.0 m)
Side position / side eld
eld dimensions
1
2
6
5
min.
Sensitivity
4
min.
max.
0.5s
Output hold time
3
On
Off
Function switch
1 LED (function indication)
2 Cable connector
3 Sensitivity potentiometer
4 Adjustable horn antenna
Motion detection (Adjustment of relay hold time potentiometer):
•
Set potentiometer between 7-8 o'clock to get
a xed hold time of 0.5 s and a velocity of 2” (5 cm) / s
• Set potentiometer between 9-5 o'clock to get
a hold time of 0.5 s @ 9 o’clock to 4 s @ 5 o’clock, with a velocity of 4” (10 cm) / s
Function switch
OFF*
Digital lter o, normal
setting, maximum
sensitivity.
Digital lter on, when
ON
4s
ltering of vibration
and/or reective
surfaces is necessary.
Detection will be
less sensitive, requiring
more motion to activate
the Impulse
* factory setting
7
max.
5 Internal side panels (aps)
6 Function switch
7 Output hold time potentiometer
Min.
Min.
Max.
Max.
Top
view
+1 Step
5˚
min.
15˚
Factory setting
0 point
15˚
20˚
30˚
45˚
max.
45˚
3 Steps
4 Steps
9 Steps
FCC APPROVAL
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
*this device may not cause harmful interference, and
*this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
paticular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
*Reorient or relocate the receiving antenna
*Increase the separation between the equipment and receiver
*Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
*Consult the dealer or an experienced radion/TV technician for help
Warning: Changes or modifications to this equipment not expressly approved by Bircher Reglomat AG may void the FCC authorization to operate this equipment.
3
Loading...