Biotronic Technology 52505332333030 Users manual

Lifevisa

W

IRELESS BIKE CADENCE SENSOR

1

2

3

[RPS-2300] USER MANUAL

Thank you for purchasing Lifevisa products. This manual contains
information required to use Cadence Sensor. Please read this manual
thoroughly before you use the Cadence Sensor.

COMPONENTS

1 2 3

5 & 64

7

1. Cadence Sensor with Screw, Nut & Foam Pad

2. O-Ring

3. 3V CR2032 Lithium Battery

4. Battery Cover

5. Zip Tie for Cadence Sensor X 2pcs

6. Zip Tie for Cadence Magnet X 2pcs

7. Cadence Magnet with Screw & Nut

2.4GHz

2.4GHz

CADENCE SENSOR BATTERY INSTALLMENT

This Cadence Sensor includes a 3V CR2032 lithium battery.
Please follow below steps to install the battery.

Step 1.

Insert the battery (CR2032) with the positive (+) side up.

☆

Make sure the battery is hooked by the contact spring.

Step 2.

Put on the O-Ring in the groove to ensure water resistance.

☆

Make sure to place the O-Ring properly in order to prevent battery

composition from being spoiled by rain or water.

Step 3.

Place the battery cover and use a coin to twist it clockwise until it is
tight enough.

NOTE:

☆

Open the battery cover only when changing the battery to ensure a
long life,
and make sure the O-Ring is not damaged, in which case you should
replace
it with a new one.

HOST CONNECTION

This Cadence Sensor must be recognized to the host before being used
for the first time. We recommend making this approach before
installment. Please follow below instructions to complete the

1. Turn on the host and enter
connection mode. The host will
wait the signal for 1 minute. If
not receiving the signal, the host
will exist the connection mode

☆

The effective distance/range is within 10 meters. Be sure no other

devices are within this distance making the same approach.

2. Press the set key of Cadence Sensor. Then wait for connection.

set key

3. The host should begin to display a reading, showing the connection has
been done and you can start to install the Cadence Sensor and Magnet.

Connection

done!!

NOTE:

the device.

4

5

TROUBLESHOOTING AND CARE

away

damage the Sensor.

6

HOW TO INSTALL

THE CADENCE

HOW TO INSTALL

THE CADENCE

HOW TO INSTALL

THE CADENCE

☆

This step only has to be done at the first time of use with the same
Cadence Sensor and host. Afterwards, even changing battery, you
don't need to reconnect to the host.

☆

See TROUBLESHOOTING AND CARE section if you are experiencing
connection issues.

The Bike Cadence Sensor measures and sends your pedaling strokes per
minute information to the host. Please follow the simple instructions
below to mount the Cadence on your bike.

To install Cadence Magnet and Cadence Sensor, you need cutters and
cross-head screwdrivers. Before installment, clean and dry the position of

1. Find an appropriate position and place the Cadence Magnet to inner
side
of the crank arm. The Magnet should face toward down tube or
chain stay.

2. Pass 2 zip ties over the Cadence Magnet and tighten them. Carefully

3. Place the Cadence Sensor on the down tube or chain stay. The
position
of Cadence Sensor should be corresponded to Magnet's. There is an
indication line on the top of the Sensor, which limits the effective
range

effective range

indication

4. Sensor's logo is toward you and you can adjust Sensor's angle to find
the
suitable gap. Remember that the best gap between Cadence Sensor
and

5. Remove the adhesive of foam pad from Cadence Sensor and attach the
Cadence Sensor to the marked position on the down tube or chain stay.

6. Pass 2 zip ties over the Cadence Sensor and tighten them. Carefully
snug 2 zip ties and trim the excess. Make sure the Cadence Sensor
is mounted securely.

7. Fine-tune the angle of Cadence Sensor to ensure the Magnet can pass
as close to the Sensor as possible but does not touch it. The gap
between the Sensor and the Magnet should be 4mm (0.16"). Finally,
tighten the screw on the Sensor with a screwdriver.

NOTE:

☆

If you have done host connection before installment, make sure you do
not touch the set key accidentally; otherwise, please repeat HOST
CONNECTION section.

Troubleshooting of the Cadence Sensor

● If you are not getting a good connection to the host, please
(a) Make sure the position of the Sensor to the Magnet is installed
correctly.
(b) Make sure the gap between the Sensor and Magnet is appropriate.
(c) Check if the battery is installed properly or change a new battery.
(d) Repeat HOST CONNECTION section.

● The effective range of the whole system is 3 meters. If the host is

Care of the Cadence Sensor and Magnet

● Keep the Cadence Sensor and Magnet clean after every use.

● Keep the Cadence Sensor and Magnet out of extremely cold and hot.

We care about your safety. Make sure the device is not against any parts
of your bike and to avoid being heavily hit during cycling as it may

For the latest version of this user manual and more product information,

please visit our website at

http://www.biotronic.com.tw