Viotech 3200+ Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.
Table of Contents
Chapter 1: Introduction ........................................ 1
1.1 Before You Start ................................................................................ 1
1.2 Package Checklist............................................................................. 1
1.3 Motherboard Features...................................................................... 2
1.4 Rear Panel Connectors ..................................................................... 3
1.5 Motherboard Layout......................................................................... 4
Chapter 2: Hardware Installation .......................... 5
2.1 Installing Central Processing Unit (CPU)....................................... 5
2.2 FAN Headers...................................................................................... 5
2.3 Installing System Memory................................................................ 6
2.4 Connectors and Slots......................................................................... 8
Chapter 3: Headers & Jumpers Setup .................. 11
3.1 How to Setup Jumpers .................................................................... 11
3.2 Detail Settings.................................................................................. 11
Chapter 4: Useful Help ........................................ 15
4.1 Driver Installation Note.................................................................. 15
5.2 Extra Information............................................................................ 16
5.3 Troubleshooting............................................................................... 17
Appendix: SPEC In Other Languages ................... 18
German.................................................................................................................. 18
French .................................................................................................................... 20
Ita lian..................................................................................................................... 22
Spanish ................................................................................................................... 24
Portuguese ............................................................................................................ 26
Polish...................................................................................................................... 28
Russian ................................................................................................................... 30
Arabic..................................................................................................................... 32
Japanese ................................................................................................................ 34
Viotech 3200+
1
CHAPTER 1: INTRODUCTION
1.1 B
EFORE YOU START
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
Prepare a dry and stable working environment with
sufficient lighting.
Always disconnect the computer from power outlet
before operation.
Before you take the motherboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
Avoid touching the components on motherboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
Keep the computer from dangerous area, such as heat
source, humid air and water.
Do not squeeze or touch CPU Cooler (Fan/Heatsink)
The operating temperatures of the computer should be
0 to 45 degrees Celsius.
1.2 PACKAGE CHECKLIST
Rear I/O Panel Shield X 1
Fully Setup Driver CD X 1 (full version manual files inside)
Serial ATA Cable X 2
Quick Installation Guide X 1
Motherboard Manual
2
1.3 MOTHERBOARD FEATURES
SPEC
CPU VIA C7-D 1.8G Processor
NanoBGA2
VIA CPU On-board
Execute D isable Bit
FSB VIA V4 BUS 800MHz
Chipset VX900
Graphics Chrome9 HD
Max Shared Video Memory is 512MB
Support DirectX 9.0 and Pixel Shader (SM2.0)
Super I/O ITE 8728
Low Pin Count Interface
Environment Control
H/W Monitor
Fan Sp eed Contro ller
Main
Memory
DDR3 Slots x 2
Each DIMM supports 512MB/1GB/2GB/4GB DDR3
Max Memory Capacity 8GB
Supports DDR3 800 / 1066
Sin gle Ch ann e l Mod e DDR3 m emory mod ule
Registered DIMM and ECC D IMM is no t suppo rted
SATA Integrated Serial ATA Controller
Data transfer rates up to 3.0 Gb/s.
SATA Version 2 .0 spec ific at ion co mpl iant .
LAN Realtek RTL8103EL 10 / 100 Mb/s auto negot iation
Sound
Codec
VIA VT1708S
5.1 channels audio out
High-Definition Audio support
PCI slot x1 Supports PCI expansion card
Slot
PCI Express Gen2 x 16 slot x1 Supports PCI-E x16 expansion card (x8-Lane only)
SATA Co nnecto r x2 Each conne ctor supports 1 SATA devices
Front Panel Connector x1 Supports front panel facilities
Front Audio Connector x1 Supports front panel audio function
CPU Fan Header x1 CPU Fan power supply
On Board
Connector
System Fan Header x1 System Fan Power supply
Viotech 3200+
3
SPEC
Clear CMOS Head er x1 Res tore CMOS dat a to fa ctory defau lt
USB Connector x2 Each connector s upports 2 front panel US B ports
Printer Port Connector x1 Each connector supports 1 Printer port
Serial Port Connector x1 Connects to RS-232 Port
Power Connector (24pin) x1 Connects to Power supp ly
Power Connector (4pin) x1 Connects to Power supply
Real Panel
I/O
PS/2 Keyboard x1
PS/2 Mouse x1
VGA Port x1
LAN Port x1
USB Port x 4
Audio Jack x3
Connects to PS/2 Keyboard
Connects to PS/2 Mouse
Connects to monitor
Connects to RJ-45 ethernet cab le
Connects to USB devices
Provide Audio-In/Out and microphone connection
Board Size 170 (W) x 220 (L) mm
OS Support Windows XP / Vista / 7
Biostar reserves the right to add or remove support
for any OS with or without notice.
1.4 REAR PANEL CONNECTORS
PS/ 2
Mouse
PS/2
Keyboard
USBX2USBX2
LAN
Line In/
Surround
Line Out
Mic In 1/
Bass/ Center
VGA
Since the audio chip supports High Definition Audio Specification, the function of each audio
jack can be defined by software. The input / output function of each audio jack listed above
represents the default setting. However, when connecting external microphone to the audio
port, please use the Mic In (Pink) audio jack.
Motherboard Manual
4
1.5 MOTHERBOARD LAYOUT
KBMS1
VGA 1
AUDIO1
RJ45USB1
USB3
CP U_FAN1
JUSBV2
LAN
Codec
F_AUDIO1 J_COM1 J_PRINT1
SYS_FAN1
PEX16_1
PCI1
BAT1
PANE L1
Super
I/O
BIOS
JCMOS1
SATA2
SATA1
F_U SB2
F_USB1
JUSBV1
ATX PWR1
DIMMA1
DIMMA2
ATX PWR2
CPU 1
VIA
VX900
VIA
C7-D
1.8G
Note: ■ represents the 1st pin.
Viotech 3200+
5
CHAPTER 2: HARDWARE INSTALLATION
2.1 I
NSTALLING CENTRAL PROCESSING UNIT (CPU)
The motherboard includes an embedded VIA C7-D or Nano processor,
and a heatsink has been installed to provide sufficient cooling.
2.2 FAN HEADERS
These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.
CPU_FAN1: CPU Fan Header
Pin
Assignment
1 Ground
2 Power
3 FAN RPM rate sense
14
4 Smart Fan Control
SYS_FAN1: System Fan Header
Pin
Assignment
1 Ground
2 +12V
13
3 FAN RPM rate
sense
Note:
CPU_FAN1 supports 4-pin head connector; SYS_FAN1, 3-pin head one. When
connecting with wires onto connectors, please note that the red wire is the positive and
should be co nnected to pin#2, and the black wire is Ground and should be connected to
GND.
Motherboard Manual
6
2.3 INSTALLING SYSTEM MEMORY
A. DDR3 Module
DIMMA 1
DIMMA 2
1. Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.
Viotech 3200+
7
B. Memory Capacity
DIMM Socket
Location
DDR3 Module
Total Mem ory
Size
DIMMA1 512MB/1GB/2GB/4GB
DIMMA2 512MB/1GB/2GB/4GB
Max is 8GB.
Motherboard Manual
8
2.4 CONNECTORS AND SLOTS
SATA1/SATA2: Serial ATA Connectors
The motherboard has a PCI to SATA Controller with 2 channels SATA interface,
it satisfies the SATA 2.0 spec and with transfer rate of 3Gb/s.
Pin Assignment
1 Ground
2 TX+
3 TX-
4 Ground
5 RX-
6 RX+
7
4
1
SATA2
SATA1
7 Ground
ATXP WR2: AT X P ower Source Connector
This connector provides +12V to CPU power circuit. Please make sure this
connector has been plugged in perfectly.
Pin
Assignment
1 +12V
2 +12V
3 Ground
1234
4 Ground
Viotech 3200+
9
ATXP WR1: AT X P ower Source Connector
This connector allows user to connect 24-pin power connector on the ATX
power supply.
1
12
13
24
Pin Assignment Pin Assignment
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 Gro und 3 Gro und
16 PS_ON 4 +5V
17 Gro und 5 Gro und
18 Ground 6 +5V
19 Gro und 7 Gro und
20 NC 8 PW_OK
21 +5V 9 Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V
PCI1: Peripheral Component Interconnect Slot
The motherboard is equipped with 1 standard PCI slot. PCI stands for Peripheral
Component Interconnect, and it is a bus standard for expansion cards. This PCI
slot is designated as 32 bits.
PCI1
Motherboard Manual
10
PEX16_1: PCI-Express x16 Slot
- PCI-Express 2.0 compliant (x8-Lane only).
- Maximum theoretical realized bandwidth of 4GB/s simultaneously per
direction, for an aggregate of 8GB/s totally.
PEX16_1
Viotech 3200+
11
CHAPTER 3: HEADERS & JUMPERS SETUP
3.1 H
OW TO SETUP JUMPERS
The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.
Pin opened Pin closed Pin1-2 closed
3.2 DETAIL SETTINGS
PANEL1: Front Panel Header
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connections. It allows user to connect the PC case’s front panel switch
functions.
1
PWR_LED
ON /O FF
RST
HLED
SPK
++
+
9
-
-
8
16
+
Pin Assignment Function Pin Assignment Function
1 +5V 9 N/A
2 N/A 10 N/A
N/A
3 N/ A 1 1 N/A N/A
4 Speaker
Speaker
Connector
12 Power LED (+)
5 HDD LED (+) 13 Power LED (+)
6 HDD LED (-)
Hard drive
LED
14 Power LED (-)
Power LED
7 Ground 15 Power button
8 Reset control
Reset button
16 Ground
Power-on button
Motherboard Manual
12
F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel
This motherboard provides 2 USB 2.0 headers, providing user to connect
additional USB cable on the PC front panel, and also can be connected with
internal USB devices, like USB card reader.
Pin Assignment
1 +5V (fused)
2 +5V (fused)
3 USB4 USB5 USB+
6 USB+
7 Ground
8 Ground
9 Key
1
9
2
10
F_USB2 F_USB1
10 NC
JUSBV1/JUSBV2: Power Source Headers for USB Ports
Pin 1-2 Close:
JUSBV1: +5V for USB ports at front panel (F_USB1/F_USB2).
JUSBV2: +5V for USB ports at USB3/RJ45USB1.
Pin 2-3 Close:
JUSBV1: +5V STB for USB ports at front panel (F_USB1/F_USB2).
JUSBV2: +5V STB for USB ports at USB3/RJ45USB1.
1
3
Pin 1-2 close
1
3
JUSBV1
JUSBV2
1
3
Pin 2-3 close
Note:
In order to support this function “Power-On system via USB device,” user should place
“JUSBV1/ JUSBV2” jumper cap on Pin 2-3 indi vidually.
Viotech 3200+
13
F_AUDIO1: Front Panel Audio Header
This header allows user to connect the front audio output cable with the PC front
panel.
Pin Assignment
1 Mic Left in
2 Ground
3 Mic Right in
4 GPIO
5 Right line in
6 Jack Sense
7 Front Sense
8 Key
9 Left line in
10 Jack Sense
19
210
JCMOS1: Clear CMOS Header
Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and
the CMOS data. Please carefully follow the procedures to avoid damaging the
motherboard.
13
Pin 1-2 Close:
Normal Operation (Default).
13
13
Pin 2-3 Close:
Clear CMOS data.
※ Clear CMOS Procedures:
1. Remove AC power line.
2. Set the jumper to “Pin 2-3 close”.
3. Wait for five seconds.
4. Set the jumper to “Pin 1-2 close”.
5. Power on the AC.
6. Load Optimal Defaults and save settings in CMOS.
Motherboard Manual
14
J_COM1: Serial port Connector
The motherboard has a Serial Port Connector for connecting RS-232 Port.
Pin
Assignment
1 Carrier detect
2 Received data
3 Transmitted data
4 Data terminal ready
5 Signal ground
6 Data set ready
7 Request to send
8 Clear to send
9 Ring indicator
19
210
10 NC
J_PRINT1: Printer Port Connector
This header allows you to connector printer on the PC.
1
2
25
26
Pin Assignment Pin Assignment
1 -Strobe 14 Ground
2 -ALF 15 Data 6
3 Data 0 16 Ground
4 -Error 17 Data 7
5 Data 1 18 Ground
6 -Init 19 -ACK
7 Data 2 20 Ground
8 -Scltin 21 Busy
9 Data 3 22 Ground
10 Ground 23 PE
11 Data 4 24 Ground
12 Ground 25 SCLT
13 Data 5 26 Key
Viotech 3200+
15
CHAPTER 4: USEFUL HELP
4.1 D
RIVER INSTALLATION NOTE
After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.
You will see the following window after you insert the CD
The setup guide will auto detect your motherboard and operating system.
Note:
If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.
A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.
Note:
You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader software from
http://www.adobe.com/products/acrobat/readstep2.html
Motherboard Manual
16
5.2 EXTRA INFORMATION
CPU Overheated
If the system shutdown automatically after power on system for
minutes, that means the CPU protection function has been activated.
When the CPU is over heated, the motherboard will shutdow n
automatically to avoid a damage of the CPU, and the system may not
power on again.
In this case, please double check:
1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.
After confirmed, please follow steps below to relief the CPU
0protection function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.
Viotech 3200+
17
5.3 TROUBLESHOOTING
Probable Solution
1. There is no power in the system.
Power LED does not shine; the
fan of the power supply does not
work
2. Indicator light on keyboard does
not shine.
1. Make sure power cable is
securely plugged in. (Both
A
TXPWR1 and ATXPWR2 power
connecters are plugged in,
perfectly.)
2. Replace cable.
3. Contact technical support.
System is inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drives are running.
Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.
System does not boot from a hard disk
drive, but can be booted from optical
drive.
1. Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.
2. Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
System only boots from an optical
drive. Hard disks can be read,
applications can be used, but system
fails to boot from a hard disk.
1. Back up data and applications
files.
2. Reformat the hard drive.
Re-install applications and data
using backup disks.
Screen message shows “Invalid
Configuration” or “CMOS Failure.”
Review system’s equipment. Make sure
correct information is in setup.
System cannot boot after user installs a
second hard drive.
1. Set master/slave jumpers
correctly.
2. Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.
Motherboard Manual
18
APPENDIX: SPEC IN OTHER LANGUAGES
G
ERMAN
Spezifikationen
CPU
VIA C7-D 1.8G CPU
NanoBGA2
VIA CPU On-board
Execute D isable Bit
FSB
VIA V4 BUS 800MHz
Chipsatz
VX900
Grafik
Chrome9 HD Max. 512MB gemeinsam benutzter Videospeicher
Super E/A
ITE 8728
Low Pin Count-Schnittstelle
Umgebungskontrolle
Hardware-Überwachung
Lüfterdrehzah l-Controller
Arbeitsspeich
er
DDR3 DIMM-Steckplätze x 2
Jeder DIMM unterstützt 512MB/ 1GB/2GB/4GB DDR3
Max. 8GB Arbeitsspeicher
Unterstützt DDR3 800 / 1066
Ein-Kanal DDR3 Speichermodul
registrierte DIMMs. ECC DIMMs werden nicht
unterstützt.
SATA
Integrierter Serial ATA-Controller
Datentransferrate b is zu 3Gb/s
Konform mit der SATA-Spezifikation Version 2.0
LAN
Realtek RTL8103EL 10 / 100 Mb/s Auto-Negotiation
Audio-Codec
VIA VT1708S
5.1-Kanal-Audioausgabe
Unterstützt High-Definition Audio
PCI-Steckplatz x1
Steckplätze
PCI Express Gen2 x16 Steckplatz x1
SATA-Anschluss x2 Jeder Anschluss unterstützt 1 SATA-Laufwerk
Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen
Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion
Onboard-Ans
chluss
CPU-Lüfter-Sockel x1 CPU-Lüfterstromversorgungsanschluss
Viotech 3200+
19
Spezifikationen
System-Lüfter-Sockel x1 System-Lüfter-Stromversorgungsanschluss
"CMOS löschen"-So ckel x1
USB-Anschluss x2
Jeder Anschluss unterstützt 2
Fronttafel-USB-Anschlüsse
Druckeranschluss Anschluss x1 Jeder Anschluss unterstützt 1 Druckeranschluss
Serieller Anschluss x1
Stromanschluss (24-polig) x1
St romanschluss (4-polig ) x1
Rückseiten-E
/A
PS/2-Tastatur x1
PS/2-Maus x1
VGA-Anschluss x1
LAN-Anschluss x1
USB-Anschluss x4
Audioanschluss x3
Plat inengröße
170 mm (B) X 220 mm (L)
OS-Unterstüt
zung
Windows XP / Vista / 7
Biostar behält s ich das Recht vor, ohne Ankündigung die
Unterstützung für ein Betriebssystem hinzuzufügen
oder zu ent fern en.
Motherboard Manual
20
FRENCH
SPEC
UC
VIA C7-D 1.8G CPU
NanoBGA2
VIA CPU On-board
d'exécution de bit de désactivation
Bus frontal
VIA V4 BUS 800MHz
Chipset
VX900
Graphiques
Chrome9 HD Mémoire vidéo partagée maximale de 512 Mo
Super E/S
ITE 8728
Int erfa ce à f aib le co mpt e de b roches
Initiatives de contrôle environnementales
Mon iteur d e matériel
Contrôleur de vitess e de ventilateur
Mémoire
principale
Fentes DDR3 DIMM x 2
Chaque DIMM prend en charge des DDR3 de
512Mo/1Go/2Go/4Go
Capac ité mé moire max imale de 8 Go
Prend en charge la DDR3 800 / 1066
Module d e mémoire DDR3 à mode à simple voie
Les DIMM à registres et DIMM avec code correcteurs
d'erreurs ne sont pas prises en charge
SATA
Contrô leur Serial ATA int é gré :
Taux de transfert jusqu'à 3 Go/s.
Co nforme à la spécifi cat ion S ATA Ver s ion 2.0
LAN
Realtek RTL8103EL 10 / 100 Mb/s négociation automatique
Codec audio
VIA VT1708S
Sortie audio à 5.1 voies
Prise en ch arg e de l' aud io haut e défin ition
Fente PCI x1
Fentes
Fente PCI Express Gen2 x16 x1
Connecteur SATA x2
Chaque connect eur pr end en charge 1 périp hér ique
SATA
Connecteur
embarqué
Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant
Viotech 3200+
21
SPEC
Connecteur Audio du panneau avant
x1
Prend en charge la fonction audio du panneau avant
Embase de ventilateur UC x1 Alimentation électrique du ventilateur UC
Embase de ventilateur système x1 Alimentation électrique du ventilateur système
Embase d'effacement CMOS x1
Connecteur USB x2
Chaque connecteur prend en charge 2 ports USB de
panneau a vant
Connecteur de Port d'imprimante x1 Chaque connector prend en charge 1 Port d'imprimante
Port série x1
Connecteur d'alimentat ion (24 broches)
x1
Connecteur d'alimentat ion (4 broches)
x1
E/S du
panneau
arrière
Clavier PS/2 x1
Souris PS/2 x1
Port VGA x1
Port LAN x1
Port USB x4
Fiche aud io x3
Dimensions
de la carte
170mm (l) X 220 mm (H)
Support SE
Windows XP / Vista / 7
Biostar se réserve le droit d'ajouter ou de supprimer le
support de SE avec ou sans préavis.
Motherboard Manual
22
ITALIAN
SPECIFICA
CPU
VIA C7-D 1.8G CPU
NanoBGA2
VIA CPU On-board
Execute Disable Bit
FSB
VIA V4 BUS 800MHz
Chipset
VX900
Grafica
Chrome9 HD La me mor ia vid eo cond ivisa massima è di 512 MB
Super I/O
ITE 8728
Interfaccia LPC (Low Pin Count)
Funzioni di controllo dell’ambiente:
Monitoraggio hardware
Co nt roller veloc ità vento lina
Memoria
principale
Alloggi DIMM DDR3 x 2
Ciascun DIMM supporta DDR3
512MB/1GB/2GB/4GB
Capacità massima della memo ria 8GB
Supporto di DDR3 800 / 1066
Modulo di memoria DDR3 a canale singolo
DIMM registrati e DIMM ECC non sono supportati
SATA
Co nt roller Serial ATA int egr ato
Velocità di trasferimento dei dati fino a 3 Gb/s.
Co mpatibile s pecifich e SATA Versione 2.0 .
LAN
Realtek RTL8103EL Negoziazione automatica 10 / 100 Mb/s
Codec
audio
VIA VT1708S
Uscita audio 5.1 canali
Supporto audio High-Definition (HD)
Allo gg io PCI x1
Allo gg i
Alloggio PCI Express Gen2 x16 x1
Connettore SATA x2 Ciascun connettore supporta 1 unità SATA
Co nn ettore pan nello fr on tale x1 Supporta i s ervizi d el p annello fro nt ale
Connettore audio frontale x1 Supporta la funzione audio pannello frontale
Co lletto re vent olin a C PU x 1 Aliment az ion e ven to lin a CP U
Connettori
su scheda
Co lletto re vent olin a sist ema x 1 A limentazio ne ventolina di sis tema
Viotech 3200+
23
SPECIFICA
Co lletto re cance llazione CMOS x1
Connettore USB x2
Ciascun connettore supporta 2 porte USB
pannello frontale
Connettore Porta stampante x1 Ciascun connettore supporta 1 Porta stampante
Porta seriale x1
Connettore alimentazione (24 pin)
x1
Connettore alimentazione (4 pin ) x1
I/O
pannello
posteriore
Tas t ier a P S/2 x1
Mou se PS/2 x1
Porta VGA x1
Port a LAN x 1
Port a USB x4
Connettore audio x3
Dimension
i sched a
170 mm (larghezza) x 220 mm
(altez za)
Sistemi
op erativi
supportati
Windows XP / V ista / 7
Biostar si riserva il diritto di aggiungere o
rimuovere il supporto di qualsiasi sistema
operativo senza preavviso.
Motherboard Manual
24
SPANISH
Especificación
CPU
VIA C7-D 1.8G CPU
NanoBGA2
VIA CPU On-board
Bit de deshabilitación de ejecución
FSB
VIA V4 BUS 800MHz
Conjunto de
chips
VX900
Gráficos
Chrome9 HD Memo ria máx ima de v ídeo co mpart ida de 512 MB
Súper E/S
ITE 8728
Interfaz de cuenta Low Pin
In ic iat ivas de co nt rol de ent orno
Monitor hardware
Controlador de velocidad de ventilador
Memoria
principal
Ranuras DIMM DDR3 x 2
Cada DIMM admite DDR de 512MB/1GB/2GB/4GB
Capacidad máxima de memoria de 8GB
Admite DDR3 de 800 / 1066
Módulo de memoria DDR3 de canal Sencillo
No ad mite DIMM registrados o DIMM compatibles con ECC
SATA
Controlador ATA Serie Integrado
Tasas de transferencia de hasta 3 Gb/s.
Co mpatible co n la versió n S ATA 2.0.
Red Local
Realtek RTL8103EL Negociación de 10 / 100 Mb/s
Códecs de
sonido
VIA VT1708S
Salida de sonido de 5.1 canales
Soporte de sonido Alta Definición
Ranura PCI X1
Ranuras
Ranura PCI Express Gen2 x16 X1
Conector SATA X2 Cada conector soporta 1 dispositivos SATA
Co necto r d e p ane l frontal X1 Soport a insta lac iones en e l p ane l f rontal
Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal
Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU
Conectores
en p laca
Cabecera de ventilador de sistema X1 Fuente de alimentación de ventilador de sistema
Viotech 3200+
25
Especificación
Cabecera de borrado de CMOS X1
Conector USB X2 Cada conector soporta 2 puerto s USB frontales
Conector Puerto de impresora X1 Cada conector soporta 1 Puerto de impresora
Puert o serie X 1
Conector de alimentación X1
(24 patillas)
Conector de alimentación X1
(4 patillas)
Panel
trasero de
E/S
Tec la do PS /2 X1
Ratón PS/2 X1
Puerto VGA X1
Puerto de red local X1
Puert o USB X4
Conector de sonido X3
Ta ma ño d e
la placa
170 mm. (A) X 220 mm. (H)
Soporte de
sistema
operativo
Windows XP / Vista / 7
Biostar se reserva el derecho de añadir o retirar el soporte
de cualquier SO con o sin aviso previo.
Motherboard Manual
26
PORTUGUESE
ESPECIFICAÇÕES
CPU
VIA C7-D 1.8G CPU
NanoBGA2
VIA CPU On-board
Execute D isable Bit
FSB
VIA V4 BUS 800MHz
Chipset
VX900
Placa
gráf ica
Chrome9 HD Memória de vídeo máxima partilhada: 512 MB
Especificaçã
o Super I/O
ITE 8728
Interface LPC (Low Pin Count)
In ic iat ivas para controlo do a mb iente
Monitorização do hardware
Controlador da velocidade da ventoinha
Memória
principal
Ranhuras DIMM DDR3 x2
Cada módulo DIMM suporta uma memória DDR3 de
512MB/1GB/2GB/4GB
Capac idad e máx ima de memó ri a: 8GB
Suporta módulos DDR3 800 / 1066
Módulo de memória DDR3 d e canal si mples
Os módulos DIMM registados e os DIMM ECC não são
suportados
SATA
Controlador Serial ATA integrado
Velocidades de transmissão de dados até 3 Gb/s.
Compatibilidade co m a especif icação SATA versão 2.0.
LAN
Realtek RTL8103EL Auto negociação de 10 / 100 Mb/s
Codec de
som
VIA VT1708S
Saída de áudio de 5.1 canais
Suporta a especificação High-Definition Audio
Ranhura PCI x1
Ranhuras
Ranhura PCI Express Gen2 x16 x1
Conector SATA x2 Cada conector suporta 1 dispositivo SATA
Conector do painel frontal x1 Para suporte de várias funções no painel frontal
Conectores
na placa
Conector de áudio frontal x 1 Suporta a fun ção de áudio no paine l frontal
Viotech 3200+
27
ESPECIFICAÇÕES
Conector da ventoinha da CPU x1 Alimentação da ventoinha da CPU
Conector da ventoinha do sistema x1 Alimentação da ventoinha do sistema
Conector para limpeza do CMOS x1
Conector USB x2 Cada conector suporta 2 portas USB no painel frontal
Conector da para impressora x1 Cada conector suporta 1 Porta para impressora
Port a sér ie x1
Conector de alimentação (24 pinos)
x1
Conector de alimentação (4 pinos)
x1
Entradas/S
aídas no
painel
traseiro
Tec la do PS /2 x 1
Rato PS/2 x1
Porta VGA x1
Port a LAN x 1
Port a USB x4
Tomada de audio x3
Tamanho
da placa
170 mm (L) X 220 mm (A)
Sistemas
operativos
suportados
Windows XP / Vista / 7
A Biostar reserva-se o direito de adicionar ou remover
suporte para qualquer sistema operativo com ou sem
av iso pr évio.
Motherboard Manual
28
POLISH
SPEC
Procesor
VIA C7-D 1.8G CPU
NanoBGA2
VIA CPU On-board
Execute D isable Bit
FSB
VIA V4 BUS 800MHz
Chipset
VX900
Graf ika
Chrome9 HD
Maks. wielkość współdzielo nej pam ięci video wynosi
512MB
Pamięć
główna
Gniazda DDR3 DIMM x 2
Każde gniazdo DIMM obsługuje moduły
512MB/1GB/2GB/4GB DDR3
Maks. wielkość pamięci 8GB
Obsługa DDR3 800 / 1066
Mod uł pamięci DDR3 z trybem pojedynczego kanału
Brak obsług i Register ed DIMM oraz ECC DIMM
Super I/O
ITE 8728
Interfejs Low Pin Count
Funkcje kontroli warunków pracy
Mon itor H/W
Kontroler prędkości went ylato ra
SATA
Zintegrowany kontroler Serial ATA
Transfer danych do 3 Gb/s.
Zgodność ze specyfikacją SATA w wersj i 2. 0.
LAN
Realtek RTL8103EL 10 / 100 Mb/s z automatyczną negocjacją szybkości
Kodek
dźwiękowy
VIA VT1708S
5.1 kanałowe wyjście audio
Obsługa High- Def in ition Au d io
Gniazdo PCI x1
Gniazda
Gniazdo PCI Express Gen2 x16 x1
Złącze SATA x2 Każde złącze obs ługuje 1 urządzenie SATA
Złącze panela przedniego x1 Obsługa elementów panela przedniego
Złącza
wbud owan e
Przednie złącze audio x 1 Obsługa funkcji audio na panelu przednim
Viotech 3200+
29
SPEC
Złącze główkowe wentylatora procesora
x1
Zasilanie wentylatora procesora
Złącze głó wkow e wenty latora
systemowego x2
Zasilanie wentylatora systemowego
Złącze głó wkowe kasowania CMOS x1
Złącze USB x2
Każde złącze obs ługuje 2 porty USB na panelu
przednim
Złącze Port drukarki x1 Każde złącze obs ługuje 1 Port drukarki
Port szeregowy x1
Złącze zasilania (24 p inowe) x1
Złącze zas ilania (4 pino we) x 1
Back Panel
I/O
Klawiatura PS/2 x1
Mys z PS/2 x 1
Port VGA x1
Port LAN x1
Port USB x4
Gniazdo audio x3
Wymiary
płyty
170 mm (S) X 220 mm (W)
Obsluga
systemu
operacyjne
go
Windows XP / Vista / 7
Biostar zastrzega sobie prawo dodawania lub
odwoływania obs łu g i do wo ln ego sys temu
operacyjnego b ez powiado mien ia.
Motherboard Manual
30
RUSSIAN
СПЕЦ
CPU
(центральн
ый
процессор)
VIA C7-D 1.8G CPU
NanoBGA2
VIA CPU On-board
Execute D isable Bit
FSB
VIA V4 BUS 800МГц
Набо р
микросхем
VX900
Графика
Chrome9 HD
Максимальная совместно используемая вид ео
память составляет 5 12 МБ
Основная
память
Слоты DDR3 DIMM x 2
Каждый модуль DIMM поддерживает
512МБ /1ГБ/2ГБ /4ГБ DDR3
Максимальная ёмкость памяти 8 ГБ
Поддержка DDR3 800 / 1066
Мод уль памяти с одноканальным режимом DDR3
Не поддерживает зарегистрированные модули
DIMM and ECC DIMM
Super I/O
ITE 8728
Интерфейс с низким количеством выводов
Инициативы по охране окружающей среды,
Аппаратный монитор
Регул ято р скорости
SATA
Встроенное п осл едоват ельное
устройство управл ения ATA
скорость передачи данных до 3 гигабит/с.
Соответствие специ фикации SATA версия 2.0.
Локальная
сеть
Realtek RTL8103EL Автомати ческо е со глас овани е 10 / 100 Мб/с
Звуко вой
кодек
VIA VT1708S
5.1канальный звуковой выход
Звуко вая поддержка Hig h- Defi nition
Слот PCI x1
Слоты
Слот PCI Express Gen2 x16 x1
Разъ ём SATA x2 Каждый разъём поддерживает 1 устройство SATA
Разъ ём на лицевой панели x1 Поддержка устройств на лицевой панели
Встроенны
й разъём
Входной звуковой разъём x1 Поддержка звуко вых функций на лицевой панели
Viotech 3200+
31
СПЕЦ
Контактирующее приспособление
вентил ято ра центрального
процессора x1
Источник пит ания для вентилято ра централь ного
процессора
Контактирующее приспособление
вентил ято ра системы x1
Источник пит ания для вентилято ра системы
Открытое контактир ующее
приспособление CMOS x1
USB- разъём x2
Каждый разъём поддерживает 2 USB-порта на
лицевой панели
Разъ ём Пор т подключения
принтера x1
Каждый разъём поддерживает 1 По рт подключения
принтера
Последовательный порт x1
Разъ ем питания (24 вывод) x1
Разъ ем питания (4 вывод) x1
Задняя
панель
средств
ввода-выв
ода
Клавиатура PS/2 x 1
Мышь PS/2 x1
Пор т VGA x1
Пор т LAN x1
USB- порт x4
Гнездо для подключени я наушников
x3
Разм ер
панели
170 мм (Ш) X 220 мм (В)
Поддержка
OS
Windows XP / Vista / 7
Biostar сохраняет за собой право добавлять или
удаля ть средства обеспечения для OS с или без
предварительного уведомления .
Motherboard Manual
32
ARABIC
تﺎﻔﺻاﻮﻤﻟا
وةﺪﺣ ﺔﺠﻟﺎﻌﻤﻟا
ﺔﻳﺰآﺮﻤﻟا
VIA C7-D 1.8G CPU
NanoBGA2
VIA CPU On-board
Execute D isable Bit
ﻞﻗﺎﻨﻟا ﻲﻡﺎﻡﻷ ا ﻲﺒﻥﺎﺠﻟا
ددﺮﺗ VIA V4 BUS 800 ﺰﺗﺮه ﺎﺠﻴﻡ
ﺔﻋﻮﻤﺠﻡ ﺢﺋاﺮﺸﻟا
VX900
ﺔﻗﺎﻄﺏ تﺎﻡﻮﺳﺮﻟا
Chrome9 HD
ﻰﺼﻗأ ﺔﻌﺳ ةﺮآاﺬﻟ ﻮﻳﺪﻴﻔﻟا ﺔآﺮﺘﺸﻤﻟا 512 ﺎﺠﻴﻡ ﺖﻳﺎﺏ
ةﺮآاﺬﻟا ﺴﻴﺋﺮﻟاﺔﻴ
ﺔﺤﺘﻓ DDR3 DIMMدﺪﻋ2
ﻢﻋﺪﺗ ﻞآ ﺔﺤ ﺘﻓ DIMM ﻢﻋﺪﺗ ةﺮآاذ ﻦﻡ عﻮﻥ DDR3 ﺔﻌﺳ /512 ﺎﺠﻴﻡ ﺖﻳﺎﺏ و1/
و2/ و4 ﺎﺠﻴﺝ ﺖﻳﺎﺏ
ﺔﻌﺳ ةﺮآاذ ىﻮﺼﻗ 8 ﺎﺠﻴﺝ ﺖﻳﺎﺏ
ﻢﻋﺪﺗ ةﺮآاﺬﻟا ﻦﻡ عﻮﻥ DDR3 تﺎﻌﺳ 800 / 1066 ﺎﺠﻴﻡ ﺖﻳﺎﺏ
ةﺪﺣو ةﺮآاذ DDR3 ﺔﻳدﺎﺣأ ةﺎﻨﻘﻟا
ﻻ ﻢﻋﺪﺗ ﻖﺋﺎﻗر ةﺮآاﺬﻟا DIMM ﻚﻠ ﺗو ﻲﺘﻟا ﻻ ﺘﺗﻖﻓاﻮ ﻊﻡ ECC
Super I/O
ITE 8728
ﺗﻢﻋﺪ ﺔﻴﻨﻘﺗ Low Pin Count In terface
ﻞﺋﺎﺳو ﻢﻜﺤﺘﻟا ﻲﻓ ﺔﺌﻴﺒﻟا:
ﺐﻗاﺮﻡ ﺔﻓﺮﻌﻤﻟ ﺔﻟ ﺎﺣ ةﺰﻬﺝﻷا
ﺐﻗاﺮﻡ ﻲﻓ ﺔﻋﺮ ﺳ ﺔﺣوﺮﻤﻟا
SATA
ﻢﻜﺤﺘﻡ Serial ATA ﻞﻡﺎﻜﺘﻡ
ﻞﻘﻥ تﺎﻥﺎﻴﺒﻟا تﺎﻋﺮﺴﺏ ﻞﺼﺗ ﻰﻟإ 3 ﺖﺏﺎﺠﻴﺝ/ﺔﻴﻥﺎﺛ.
ﺔﻘﺏﺎﻄﻡ تﺎﻔﺹاﻮﻤﻟ SATA راﺪﺹﻹا 2.0.
ﺔﻜﺒﺵ ادﺔﻴﻠ ﺧ
10/100
Realtek RTL8103EL
ضوﺎﻔﺗ ﻲﺋﺎﻘﻠﺗ 10/100 ﺎﺠﻴﻡ ﺖﻳﺎﺏ /ﺔﻴﻥﺎﺛ
ﻚﻳدﻮآ تﻮﺼﻟا
VIA VT1708S
5.1 تاﻮﻨﻗ جﺮﺨﻟ تﻮﺼﻟا
ﻢﻋﺪﺗ ﺔﻴﻨﻘﺗ تﻮﺼﻟا ﻲﻟ ﺎﻋ ﻒﻳﺮﻌﺘﻟا ﻦﻡ
ﺔﺤﺘﻓPCI دﺪﻋ1
تﺎﺤﺘﻔﻟا
ﺔﺤﺘﻓx1 6 PCI Express Gen2 دﺪﻋ1
ﺬﻔﻨﻡSATA دﺪﻋ2ﻢﻋﺪﻳ ﻞآ ﺬﻔﻨﻡ ﺪﺣاو ﻦﻡ ةﺰﻬﺝأ SATA
ﺔﻴﻡﺎﻡﻷا ﺔﺣﻮ ﻠﻟا ﺬﻔﻨﻡ دﺪﻋ1ﻢﻋﺪﻳ تاﺰﻴﻬﺠﺗ ﺔﺣﻮﻠ ﻟا ﺔﻴﻡﺎﻡﻷا
ﺬﻓﺎﻨﻤﻟا ﻰﻠﻋ ﺢﻄﺳ
ﺔﺣﻮﻠﻟا
ﻲﻡﺎﻡﻷا تﻮﺼﻟا ﺬﻔﻨﻡ دﺪﻋ1ﻢﻋﺪﻳ ﺔﻔ ﻴﻇو تﻮﺼﻟا ﺔﺣﻮﻠﻟﺎﺏ ﺔﻴﻡﺎﻡﻷا
Viotech 3200+
33
تﺎﻔﺻاﻮﻤﻟا
ﺔﻳﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻡ ﺔﻠﺹو دﺪﻋ1ﻞﻴﺹﻮﺘﻟ ﺔﻗﺎﻄﻟا ﺔﺣوﺮﻤﻟ ةﺪﺣو ﺔﺠﻟﺎﻌﻤﻟا ﻊﻡ ﺔﻔﻴﻇو
مﺎﻈﻨﻟا ﺔﺣوﺮﻡ ﺔﻠﺹو دﺪﻋ1ﻞﻴﺹﻮﺘﻟ ﺔﻗﺎﻄﻟا ﺔﺣوﺮﻤﻟ مﺎﻈﻨﻟا
ﺢﺴﻡ ﺔﻠﺹوCMOS دﺪﻋ1
ﺬﻔﻨﻡUSB دﺪﻋ2ﻢﻋﺪﻳ ﻞآ ﺬﻔﻨﻡ ﻲﺘﺤﺘﻓ USB ﺔﺣﻮﻠ ﻟﺎﺏ ﺔﻴﻡﺎﻡﻷا
ﺔﻌﺏﺎﻃ ﺬﻔ ﻨﻡ دﺪﻋ1
ﻲﻠﺴﻠﺴﺗ ﺬﻔﻨﻡ دﺪﻋ1
ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ)24سﻮﺏد( دﺪﻋ1
ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ)4سﻮﺏد( دﺪﻋ1
ﺬﻓﺎﻨﻡ ﻞﺧد/جﺮﺧ
ﺔﺣﻮﻠﻟا ﺔﻴﻔﻠﺨﻟا
ﺣﻮﻟ ﺢﻴﺗﺎﻔﻡ ﺔPS/2 دﺪﻋ1
سوﺎﻡ PS/2 دﺪﻋ1
ﺬﻔﻨﻡVGA دﺪﻋ1
ﺔﻴﻠﺤﻡ لﺎﺼﺗا ﺔﻜﺒﺵ ﺬﻔ ﻨﻡ دﺪﻋ1
ﺬﻓﺎﻨﻡUSB دﺪﻋ4
تﻮﺹ ﺲﺒﻘﻡ دﺪﻋ3
ﻢﺠﺣ ﺔﺣﻮﻠﻟا
170 ﻢﻡ)ضﺮﻋ (X 220 ﻢﻡ)عﺎﻔﺗرا(
ﻢﻋد ﺔﻤﻈﻥ أ ﻞﻴﻐﺸﺘﻟا
Windows XP / Vista / 7
ﻆﻔﺘﺤﺗ Biostar ﺎﻬﻘﺤﺏ ﻲﻓ ﺔﻓﺎﺿإ وأ ﺔﻟازإ ﻢﻋﺪﻟا يﻷ مﺎﻈﻥ ﻐﺸﺗﻞﻴ رﺎﻄﺧﺈﺏ وأ نو ﺪﺏ
رﺎﻄﺧإ.
Motherboard Manual
34
JAPANESE
仕様
CPU
VIA C7-D 1.8G CPU
NanoBGA2
VIA CPU On-board
Execute D isable Bit
FSB
VIA V4 BUS 800MHz
チップセット
VX900
グラフィック
ス
Chrome9 HD 最大の共有ビデオメモリは512MBです
メインメモリ
DDR3 DIMMスロット x 2
各DIMMは 512MB/1GB/2GB/4GB DDR3をサポート
最大メモリ容量8GB
DDR3 800 / 1066 をサポート
シングル チャンネルモードDDR3メモリモジュール
登録済みDIMMとECC DIMMはサポートされません
Super I/O
ITE 8728
低ピンカウントインターフェイス
環境コントロールイニシアチブ、
H/Wモニター
ファン速度コントローラ/ モニター
SATA
統合シリアルATA コントローラ
最高3 Gb/秒のデータ転送速度
SATAバージョン2.0仕様に準拠。
LAN
Realtek RTL8103EL 10 / 100 Mb/秒のオートネゴシエーション
サウンド
Codec
VIA VT1708S
5.1チャンネルオーディオアウト
ハイデフィニションオーディオのサポート
PCIスロット x1
スロット
PCI Express Gen2 x16スロット x1
SATAコネクタ x2 各コネクタは1つのSATAデバイスをサポートします
フロントパネルコネクタ x1 フロントパネル機能をサポートします
フロントオーディオコネクタ x1 フロントパネルオーディオ機能をサポートします
オンボードコ
ネクタ
CPUファンヘッダ x1 CPUファン電源装置
Viotech 3200+
35
仕様
システムファンヘッダ x1 システムファン電源装置
CMOSクリアヘッダ x1
USBコネクタ x2
各コネクタは2つのフロントパネルUSBポートをサポートし
ます
プリンタポートコネクタ x1 各コネクタは1つのプリンタポートをサポートします
シリアルポート x1
電源コネクタ(24ピン) x1
電源コネクタ(4ピン) x1
背面パネル
I/O
PS/2キーボード x1
PS/2マウス x1
VGAポート x1
LANポート x1
USBポート x4
オーディオジャック x3
ボードサイズ
170 mm (幅) X 220 mm (高さ)
OSサポート
Windows XP / Vista / 7
Biostarは事前のサポートなしにOSサポートを追加または削
除する権利を留保します。
2011/05/03
Loading...