!
!
!
!
!
!
GPR Plus
GLOBAL POCKET READER™ PLUS
QUICK START GUIDE
Rev 1.2
Go to www.biomark.com for complete User Manual,
Software and Software User Guide.
DESCRIPTION
GPR+ is a universal portable reader for RFID PIT tags with
the purpose of identifying animals.
The device can read a wide range of technologies: FDXB ISO, HDX ISO and FDX-A (FECAVA). GPR+ can also read
and display the PIT Tag when reading PIT tags with the
Biomark BioTherm13 temperature sensing tags.
In addition to its PIT tag reading functions, the GPR+
scanner can store up to 3000 IDs in its internal memory,
each associated with a time/date stamp, in its internal
memory and transmit them to a PC via an USB cable or
wirelessly using Bluetooth®.
The GPR+ is supplied with the PIT tag Management
Software which enables user to download the reader’s
memory, change the scanner settings or update the
GPR+ firmware. It is available for download at
www.biomark.com with the complete User Manual and
Software User Guide.
982005624300245
37.5°C / 99.5°F
985005624300245
MEM:0008
Bluetooth® indicator
Battery level indicator
ID code
Memory level (when enabled)
or temperature information
GETTING STARTED
GPR+ comes supplied with six AAA rechargeable NiMH
batteries which must be fully charged prior to use, as
diagram below (step 1 through 3).
If preferred, six standard AAA alkaline batteries can also
be used and should not be charged (follow only step 1).
Step 1 – Remove retention screw located on bottom
back of GPR+. Place batteries according to polarity
indicators.
Replace lid and screw.
WARNING! BATTERIES MUST BE INSTALLED AS
PICTURED TO AVOID EXCESSIVE HEAT OR POTENTIAL
FOR PERMANENT DAMAGE TO THE READER WHILE
CHARGING
Step 2 – Remove USB plug and attach cable to GPR+.
Step 3 – Plug the adaptor into power outlet. The battery
level icon will flash while charging and stop flashing when
fully charged. A full charge will take approximately 3
hours.
DO NOT MIX RECHARGEABLE AND STANDARD BATTERIES
DO NOT ATTEMPT TO CHARGE STANDARD ALKALINE
BATTERIES.
CHARGE THE BATTERIES INDOORS ONLY AND BETWEEN 0°C
AND 40°C.
To extend battery life, charge unit at least every three
months, if reader is unused.
READING PIT TAGS
When scanning for PIT tags PRESS AND HOLD BUTTON
DOWN during procedure. The reader will display
“SEARCHING”.
Test reader by placing test chip provided on key chain. If
PIT tag number is not detected, consult USER MANUAL.
Do not attach key chain to reader.
If a PIT tag is detected, the number will appear on the
display. If a PIT tag is not detected it will display “NO ID
FOUND”.
Keep the scanner as close to the animal or item as
possible and move slowly over standard locations for the
particular species.
Note 1 – PIT tag placement may vary per animal.
PIT TAG MANAGEMENT SOFTWARE
GPR+ scanner comes with PIT tag Management Software
only for Windows® operating system. Please refer to PIT
tag Management Software User Guide to install the tool
on your PC.
PIT tag Management Software offers the following
capabilities:
• Change reader settings.
• Download reader memory and export animal
ID’s to Excel.
• Use reader as a virtual keyboard.
• Update reader firmware.
Reader
memory
Download
reader
memory
Configure
your reader
Choose language
Export memory to
Excel
Display
scanned ID
Copy ID
Display of microchip
temperatureä
READER SETTINGS IN PIT TAG MANAGEMENT
SOFTWARE
GPR+ is delivered with Memory and Bluetooth® enabled.
These options can be disabled through the PIT tag
Management Software, as in diagram below:
TROUBLESHOOTING
• PIT tag not detected: Confirm that it is being
operated distant from metal objects and
computer equipment, including metal objects,
such as collar with metal objects and stainless
steel tables.
• Memory cannot be downloaded: Make sure
memory is enabled in reader settings (refer to PIT
tag Management Software User Guide for more
information).
• Bluetooth not visible: Check if Bluetooth icon
appears on the display. If not, enable Bluetooth
by using PIT tag Management Software.
• Bluetooth visible but not connectable: Make sure
your reader is configured to be visible and
connectable in PIT tag Management Software
(refer to PIT tag Management Software User
Guide for more information).
• Incorrect date/time: Connect reader to PIT tag
Management Software. This will synchronize the
date and time with the computer.
Note 2 – For other troubleshooting questions, consult user
manual.
WARRANTY
The Global Pocket Reader Plus is warranted against
defects in materials and workmanship, under normal use
and service for two (2) years from the day of shipment.
This warranty will not apply if adjustment, repair or parts
replacement is required because of accident, neglect,
damage during transportation or causes other than
ordinary use.
Manufacturer’s sole responsibility under this warranty shall
be at its option, to either repair or replace any product
which fails during the warranty period. In no event shall
Manufacturer be liable for any indirect or consequential
damages or loss of profit.
LEGAL INFORMATION
Trademarks
Bluetooth® is a registered trademark of Bluetooth SIG,
Inc.
Windows is a trademark or registered trademark of
Microsoft Corporation in the United States and/or other
countries.
All other trademarks are trademarks of their respective
owners.
Snapshots are according to the latest version at the moment this
document was printed.
Changes may occur without notice.
Loading...