Biodrier Biolite BJ09W, Biolite BJ09C, Biolite BJ09S Operating Instructions And Parts Manual
IFS Ltd t/a Intelligent Hand Dryers UK
www.intelligenthanddryers.com
0114 354 0047
1
BioLite
Hand dryer
Automatic
High Speed
BioLite
2
Operating Instructions and Parts Manual (Automatic)
Surface Mounted High Speed Hand Dryer
Technical Specications
Item Category Performance Data
Operating Voltage
220 - 240Vac, 50Hz, 650 - 900 WATTS (heater o/on)
Warm Air Speed Output
64 m/s, 140m³/h
Air Output Temperature
77°F (25°C) - Ambient Temperature 68°F (20°C)
Motor Type
23,000 rpm, 650W, Brush Type, Dual Bearings
Motor Thermal Protection
Auto Resetting Thermostat turns unit o,
240V at 221°F (105°C) - EURO Spec
Heater Element
250W
Heater Thermal Protection
Auto Resetting Thermostat turns unit o at, 149°F (65°C)
Drying Time
Less than 15 seconds
Decibel Rating
76 dba @ 1 mtr
Circuit Operation
Infared Automatic, self adjusting
Sensor Range
100 mm
Timing Protection
60 seconds auto shut o
Drip Proof
IP22
Isolation
CLASS I
Net Weight
4 kg
Shipping Weight
5 kg
Unit Size
W 240 x H 268 x D 176 mm
Approvals
CE, WEEE, Greenspec
Item Code Cover Type/Finish
BJ09W
Die Cast Aluminium; Epoxy Polyester Powder Coating (White)
BJ09S
Die Cast Aluminium; Epoxy Polyester Powder Coating (Silver)
BJ09C
Die Cast Aluminium; Bright Chrome
268mm
176mm
240mm
BioLite
3
Operating Instructions and Parts Manual (Automatic)
Surface Mounted High Speed Hand Dryer
General Safety Information
WARNING
This product is intended for installation by a
qualied service person. Use AWAG No.16 solid
conductor for wiring.
Failure to properly ground unit could result in
electrical shock and/or death.
Disconnect power at the service breaker before
installing or servicing.
NOT FOR HOUSEHOLD USE - MAY CAUSE BURNS
“IMPROPRE A L’USAGE DOMESTIQUE - PUET
OCCASIONNER.”
All units must be supplied with a 3-wire service. The
ground wire must be connected with the dryers
back plate.
NOTE: Do not install dryer over wash basin.
Type Y attachment
If the power supply cord is damaged, it must be
replaced by the manufacturer or its service agent or a
similar qualied person in order to avoid a hazard.
Means for disconnection must be incorporated in the
xed wiring in accordance with the wiring rules.
Installation
Installation must be carried out by a qualied electrician
1. Make sure power supply breaker is switched o.
Installation must be carried out in accordance with the
current edition of the local wiring regulations code
having jurisdiction. Installation should be performed
only by a qualied electrician.
2. Place template against wall at desired height
(see mounting height recommendations) and mark
locations of 4 mounting holes and wire service entry at
knockout (KO) location.
NOTE: For two or more dryers, dryers should be no
closer than 24 inches (610 mm) on centre.
3. Remove and retain 2 cover screws and cover.
4. Connect supply wires to terminal block where
indicated and connect ground wire to baseplate with
ground screw.
Connections:
a. Connect the live wire (coloured red or brown) to
the terminal block marked “L”.
b. Connect the neutral wire (coloured black or blue)
to the terminal block marked “N”.
c. Connect the ground wire (coloured green or green
and yellow) to the green screw marked “ ”.
Note that the colour of live and neutral wires depends
on voltage of supply service.
5. Replace cover. Do not over-tighten screws.
BioLite
4
Operating Instructions and Parts Manual (Automatic)
Surface Mounted High Speed Hand Dryer
Recommended Mounting Heights
Cleaning and Maintenance
All surfaces of the unit should be cleaned daily with a
soft cloth dampened with warm, soapy water. Polish
with a soft dry cloth.
DO NOT use caustic solutions or abrasive cleaning materials on the drier.
Operation
• No touch operation.
• Shake excess water from hands.
• Place hands under the outlet to start operation.
• Rub hands lightly and rapidly.
• Stops automatically after hands are removed.
Men’s Ladies Children, ages 11-17 Children, ages 3-10 Disabled
43” 41” 39” 33” 35”
109 cm 104 cm 99 cm 84 cm 89 cm
From oor to bottom of dryer.
BioLite
5
Operating Instructions and Parts Manual (Automatic)
Surface Mounted High Speed Hand Dryer
Diagram and Parts List
Key Description Product Code
1 Die Cast Cover HD-BL093195-01
2 Motor Housing HD-BL093195-02
3 Rubber Washers HD-BL093195-03
4 Shock Absorber HD-BL093195-04
5 Motor HD-BL093195-05
6 Blower Housing HD-BL093195-06
7 Blower Mounting Plate HD-BL093195-07
8 Mounting Plate Screws HD-BL093195-08
9 Base Plate HD-BL093195-09
10 Cover Screws HD-BL093195-10
11 Nylon Brushes HD-BL093195-11
12 Electrical Thermal Block HD-BL093195-12
Key Description Product Code
13 Cable Clamp HD-BL093195-13
14 Motor Rubber HD-BL093195-14
15 Circuit Board Module HD-BL093195-15
16 Circuit Board Cover HD-BL093195-16
17 Heater Switch HD-BL093195-17
18 Heating Element HD-BL093195-18
19 Sensor Screen HD-BL093195-19
20 Sensor Module HD-BL093195-20
21 Sensor Bracket HD-BL093195-21
22 LED Module HD-BL093195-22
23 Air Outlet Bae HD-BL093195-23
24 Bae Plate HD-BL093195-24
25
Motor Brushes
HD-BL093195-25
Loading...