Page 1
Source | Mute | 2ch
(HDMI Out Audio)
INSTALLATION
MANUAL
HDBaseT EXTENDER
B-540-EXT-330-RS-IPW
Page 2
2
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of re or electric shock, read and follow all instructions and warnings in this
manual. Keep this manual for future reference.
1. Do not expose this apparatus to rain or moisture. Do not expose this equipment to dripping
or splashing, and ensure that no objects lled with liquids, such as vases, are placed on the
equipment. Do not use this apparatus near water.
2. Do not remove cover. No user serviceable parts inside.
3. Clean only with a dry cloth.
4. Do not block any ventilation openings. Install according to manufacturer’s instructions.
5. Do not install near any heat sources such as radiators, heat registers, stoves or other
apparatus (including ampliers) that produce heat.
6. Do not override the safety purpose of the polarized or grounding plug. A polarized plug has
two blades, one of which is wider than the other. A grounding plug has two matching blades
and a third grounding prong. The wide blade or the third prong is provided for your safety. If
the provided plug does not t into your outlet, consult an electrician for replacement of the
obsolete outlet.
7. Protect the power cord from being walked on or pinched, particularly at the plug end and
where the power cord is attached to the apparatus.
8. Only use attachments and accessories specied by the manufacturer.
9. Refer all servicing to qualied service personnel. Servicing is required when the apparatus
has been damaged in any way, such as when the power supply cord or plug is damaged,
liquid has been spilled on or objects have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, the apparatus does not operate normally, or it has been
dropped.
10. To completely disconnect this equipment from power, disconnect the power supply cord
from the power outlet.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of suninsulated dangerous voltage
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
CAUTION
CAUTION: TO REDUCE THE RISK OF
ELECTRICAL SHOCK.
DO NOT REMOVE COVER. NO US ER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Page 3
3
CONTENTS
1. Product Overview ..........................................................................................................................................................4
2. Features ...............................................................................................................................................................................4
3. Package Contents ............................................................................................................................................................4
4. Device Layout ....................................................................................................................................................................5
4.1. B-540-EXT-330-RS-IPW Transmitter .......................................................................................................5
4.2. B-540-EXT-330-RS-IPW Receiver .............................................................................................................6
5. Installation ..........................................................................................................................................................................7
5.1. B-540-EXT-330-RS-IPW Transmitter Installation ...............................................................................7
5.2. B-540-EXT-330-RS-IPW Receiver Installation .....................................................................................7
6. Applications .......................................................................................................................................................................8
6.1. HDBaseT Link (RJ45) Connection ..............................................................................................................8
6.2. IR Control Connections ..................................................................................................................................9
6.2.1. Point-to-Point IR Control — Stereo (3.5mm) IR Receiver ..................................................10
6.2.2. Control System - Mono (3.5mm) IR Receiver ..........................................................................10
6.2.3. IR Flasher Out — Mono (3.5mm) ...................................................................................................11
6.3. RS-232 Control Connections .......................................................................................................................11
6.3.1. RS-232 Control (DB-9) Connection ............................................................................................12
6.3.2. RS-232 Operation Mode / Firmware Update Operation ....................................................12
6.4. IP Control Connections ..................................................................................................................................13
6.5. Thread-Locking Power Connector .............................................................................................................14
6.6 Optional Remote Power (Receiver Only) .................................................................................................15
7. Specications ....................................................................................................................................................................15
8. Support ...............................................................................................................................................................................16
9. Warranty .............................................................................................................................................................................16
Page 4
4
1. PRODUCT OVERVIEW
Welcome to Binary. This product is engineered to provide years of exceptional reliability. We
appreciate your business, and we stand committed to providing our customers with the highest
degree of quality and service in the industry.
This device extends HDMI over a single category cable using HDBaseT technology allowing
video and audio transmission to remote displays. In addition, the device is equipped with
bidirectional IR, RS-232, and Ethernet over the same category cable.
Since many installations are behind at screen TVs, the B-540-EXT-330-RS-IPW receiver is
made to mount in a double gang box and can be optionally powered from the rack to a rear
power connection.
This unit supports all HDMI dened audio and video formats, including 4K2K@30 Hz. The
Power over Cable (PoC) feature enables the extender to be powered from either end.
2. FEATURES
• In wall receiver (double gang box) design for easy installation
• Extends all HDMI formats up to:
Resolution Cat 5e/6/6a/7
1080i/720p 24-bit color 330'
Full HD 1080p 24-bit color 330'
Full HD 1080p 36-bit color 330'
Ultra HD 4K2K@30 Hz* 330'
*Compatible with HDMI 2.0 and HDCP 2.2
• Supports all HDMI supported audio formats, including DTS-HD Master and Dolby TrueHD
• Bidirectional IR, RS-232, and Ethernet
• PoC capable - can be powered from either the transmitter or receiver
• Remote power option
3. PACKAGE CONTENTS
• 1x B-540-EXT-330-RS-IPW Transmitter
• 1x B-540-EXT-330-RS-IPW Receiver
• 1x 12V DC, 2A Power Supply
• 1x Dual Gang Face Plate
• 2x Screws
• 1x Installation Manual
• 1x Power Supply Label
• 2x HDBaseT Labels
Page 5
5
4. DEVICE LAYOUT
4.1. B-540-EXT-330-RS-IPW Transmitter
Ethernet
123
ON
BA C D E F G H I K LJ
FIGURE 1: Transmitter Layout
A. Thread-locking Power Connector
Connect to the included 12V DC, 2A power Supply
B. Power LED
Lights up blue when the unit has power
C. HDMI Input
HDMI Input to connect to the HDMI output of a source
D. IR Flasher
IR output to connect to IR Flasher
E. IR Receiver
IR input to connect to IR Receiver or to output of a control system
F. IR Flasher level
Adjusts the intensity of the IR Flasher output
G. Ethernet (RJ45)
To communicate IP data between Transmitter and Receiver
H. DIP Switches
IR RCVR PWR OFF/ON
OFF to connect to control system | ON to connect to IR Receiver
DCE/DTE
To select if serial (RS232) communication via DB-9 is in DCE or DTE mode
LINK/SERVICE DIP
LINK for passthrough (normal) operation | SERVICE for rmware operation
I. RS-232
To communicate RS-232 command with the transmitter when connected to a control
system
J. HDBaseT (RJ45 )
To connect to the HDBaseT RJ45 port on transmitter
K. Link LED
Lights up green when synced with receiver
Front Back
Page 6
6
4.2. B-540-EXT-330-RS-IPW Receiver
M N
1 2 3
ON
B
A
C
D
FIGURE 2: Receiver Layout
A. HDMI Out
HDMI Output to connect to the HDMI input of a sink(display)
B. IR Receiver
IR input to connect to IR Receiver or to output of a control system
C. IR Flasher
IR output to connect to IR Flasher
D. IR Flasher level
Adjusts the intensity of the IR Flasher output
E. HDBT Link LED
Lights up green when synced with receiver
F. HDCP LED
Lights up green when HDCP link has been established; Blinks when content does not
require HDCP; Off when no HDMI signal is recognized
G. HDBT HPD LED
Lights up green when Hot Plug event is Detected
H. Power LED
Lights up blue when the unit has power
I. Thread-locking Power Connector
Connect to an optional 12V DC, 2A power supply (B-PS-12VDC-2A)
J. Ethernet (RJ45)
To communicate IP data between Transmitter and Receiver
K. RS-232
To communicate RS-232 command with the transmitter when connected to a control
system
L. DIP Switches
IR RCVR PWR OFF/ON
OFF to connect to control system | ON to connect to IR Receiver
DCE/DTE
To select if serial (RS232) communication via DB-9 is in DTE or DCE mode
SERVICE /LINK (RS-232)
SERVICE for rmware operation | LINK for passthrough (normal) operation
Front Back
Page 7
7
M. Optional Remote Power (2 Conductor Removable)
Optional connection for power from a remote power source; 2/18 wire required
Note: Use only when the Latch-Locking Power Jack is not being used. Do not connect both
power sources.
N. HDBaseT (RJ45 )
To connect to the HDBaseT RJ45 port on transmitter
5. INSTALLATION
5.1. B-540-EXT-330-RS-IPW Transmitter Installation
CAUTION: Do not connect power to the device until all other connections are made and the unit
is installed.
1. Run category cable from the location of the transmitter to the remote location of the receiver.
2. Mount the device transmitter in the desired location.
3. Connect the category cable to the device transmitter.
4. Connect the HDMI Out of a source component to the HDMI In of the transmitter using an
HDMI cable.
5. Connect the RS-232 DB-9 from a control system if being used.
6. Connect an IR control system to the IR receiver and/or IR asher if being used. Refer to
Section 6.2.
7. Connect an ethernet RJ45 cable to an ethernet enabled device if being used.
8. Connect the 12V DC, 2A power supply to the thread-locking power connector unless PoC
is being used to send power from the receiver. DO NOT plug the power supply into an AC
outlet until Receiver Installation is completed.
5.2. B-540-EXT-330-RS-IPW Receiver Installation
1. Run category cable from the location of the transmitter to the remote location of the receiver.
2. Mount the device receiver in the desired location.
3. Connect the category cable to the device receiver.
4. Connect an IR asher and/or IR receiver if being used. Refer to Section 6.2.
5. Connect an HDMI cable from the HDMI Out of device receiver to the display.
6. Connect the RS-232 DB9 to an RS-232 controllable source if being used.
7. Connect an ethernet RJ45 cable to an ethernet enabled device if being used.
8. Connect the 12V DC, 2A power supply to either the thread-locking power connector, or
the optional remote power connector, unless PoC is being used to send power from the
transmitter.
9. Connect the power supply to the AC outlet.
Page 8
8
6. APPLICATIONS
PLAY
123
ON
123
ON
Ethernet
FIGURE 3 : Application Diagram
Note: When a power supply is connected to either the transmitter or receiver, the HDBaseT
link sends power to the other unit. Only one unit requires a power supply to be connected.
6.1. HDBaseT Link (RJ45) Connection
This device is specied to operate with category cables for communication between the transmitter
and receiver. The transmission path may include a maximum of two keystones and two patch cables,
as long as the total length does not exceed 230 ft for Cat5e/6 and 330 ft for Cat6a/7.
Pi
n 1White/OrangePin 5White/Blue
Pi
n 2OrangePin 6Green
Pi
n 3White/Green Pin 7White/Brown
Pi
n 4BluePin 8Brown
TIA/EIA Standard 568-B (Gold Pins Facing Up)
FIGURE 4: RJ45 Connections
Note: The HDBaseT Link RJ45 connection includes a 12V signal. Do not connect anything to
this port other than an HDBaseT transmitter or receiver.
HDMI Source
HDMI
CAT5
HDMI
AC
Power
Back
Front
B-540-EXT-330-RS-IPW Receiver
Back Front
B-540-EXT-330-RS- IPW Transmitter
Page 9
9
6.2. IR Control Connections
Bidirectional IR signals can be transmitted between transmitter and receiver through category
cable. The IR signal can be generated either from a powered receiver or from a control system.
The following section describes these two use cases.
CAUTION: Pinout configurations for IR receivers and control systems vary. Before
connecting to this input, review this section carefully in order to match the pinouts for the
device.
IR OutputsIR Inputs
PLAY
or
123
ON
D
C
B
123
ON
AC
FIGURE 5: IR Connections
Note: Arrow direction indicates signal ow.
IR Receiver In-3.5 mm Mono—See Section 6.2.2
IR Receiver In-3.5 mm Stereo—See Section 6.2.1
IR Flasher Out-3.5 mm Mono—See Section 6.2.3
D HDBaseT Link category cable (RJ45)—See Section 6.1
Front
Front Back
B-540-EXT-330-RS-IPW Receiver
B-540-EXT-330-RS-IPW Transmitter
IR Processor/ ControllerHDMI Source
Back
Page 10
10
6.2.1. Point-to-Point IR Control — Stereo (3.5mm) IR Receiver
When using a powered IR receiver, the DIP switch for IR RCVR PWR should be set to ON. In
this case a 3.5mm (1/8") stereo jack has to be used to send 9V DC power to the receiver.
CAUTION: DO NOT connect a mono cable to this connection as damage may occur.
123
ON
1ON23
9V DC (Sleeve)
GND (Ring)
IR Signal (Tip)
FIGURE 6: Point-to-Point IR settings
6.2.2. Control System - Mono (3.5mm) IR Receiver
When using a control system which generates the signal through a mono jack, the IR RCVR
PWR switch should be in the OFF position.
123
ON
1ON23
GND (Sleeve)
IR Signal (Tip)
FIGURE 7 : Control System IR settings
Transmitter Receiver
Pinout Conguration
IR Signal (Tip)
GND (Sleeve)
9V DC(Sleeve)
Transmitter Receiver
Pinout Conguration
IR Signal (Tip)
GND (Sleeve)
Page 11
11
6.2.3. IR Flasher Out — Mono (3.5mm)
The IR Flasher level adjusts the intensity of the IR Flasher output
GND (Sleeve)
IR Signal (Tip)
FIGURE 8: IR Flasher Out
6.3. RS-232 Control Connections
Bidirectional RS-232 signals are transmitted between the device transmitter and receiver over
the category cable. The transmitter may be connected to a control system, and the receiver
may be connected to an RS-232 controllable device.
123
ON
123
ON
A
B
A
B
RS-232 Control (DB-9)- See Section 6.3.1
HDBaseT Link category - See Section 6.1
FIGURE 9: RS-232 Connections
IR Signal (Tip)
GND (Sleeve)
Pinout Conguration
Front
Back
B-540-EXT-330-RS-IPW Transmitter
RS-232 Controllable DeviceControl System
B-540-EXT-330-RS-IPW Receiver
Page 12
12
6.3.1. RS-232 Control (DB-9) Connection
To eliminate the need to make crossover or null modem cables, the RS-232 pinouts can be
congured for DCE or DTE. Set switch 2 to DCE if the connected device is DCE, and to DTE if
the connected device is DTE.
Typically the control system will be DTE and the controlled device will be DCE, however,
devices may vary. Refer to the manual for the connected devices for proper pinout
conguration.
123 4
ON
1ON231ON23
123
ON
PIN FUNCTION
2 RxD (Data Receive)
3 TxD (Data Transmit)
5 GND
PIN FUNCTION
2 TxD (Data Transmit)
3 RxD (Data Receive)
5 GND
235
FIGURE 10: RS-232 Modes and Connections
6.3.2. RS-232 Operation Mode / Firmware Update Operation
The RS-232 connection can also be used for rmware updates in addition to sending RS-232
signals. The DTE/DCE switch is used to set the RS-232 Mode.
Note: The SERVICE/LINK switch must set to LINK during normal RS-232 passthrough
operation.
To perform rmware updates, the DIP switches must be set to DTE and SERVICE. Detailed
instructions and updated rmware will be posted to www.snapav.com as they are released.
Note: The DIP switch should be set to LINK during normal operation.
123
ON
1ON23
FIGURE 11: Firmware Update settings
Transmitter Receiver
DTE Mode
RS-232 DB-9 Pinouts
DCE Mode
Transmitter
Receiver
Page 13
13
6.4. IP Control Connections
Bi-directional Ethernet signals are transmitted between the B-540-EXT-330-RS-IPW Transmitter
and Receiver over the Cat5e/6 cable. The most common use is to send Ethernet signals for
Networked TVs or any device in the remote location that has an Ethernet connection. This
connection is only to be used for standard Ethernet signals and cannot be used for other
communication formats.
FIGURE 12: IP Control Connections
Ethernet (RJ45)
HDBaseT Link category - See Section 6.1
Note: This connection is for 10/100 BaseT Ethernet ONLY. DO NOT connect a cable from an
HDBaseT port.
6.5. Thread-Locking Power Connector
CAUTION: DO NOT connect the power supply to the device until it is completely
installed and all connections have been made.
This extender pair is Power over Cable capable and therefore can be powered from either
the transmitter or receiver. When a power supply is connected to either the transmitter or
receiver, the HDBaseT link sends power to the other end.
Power for the B-540-EXT-330-RS-IPW receiver can be supplied via a remote power source
when use of the Latch-Locking Power Jack is not desired. The connection is a 2 conductor
removable plug located on the rear of the B-540-EXT-330-RS-IPW receiver.
Transmitter
Receiver
Ethernet Enabled Device
B
Network Router or Switch
1 2 3
ON
A A
B
Page 14
14
6.6. Optional Remote Power (Receiver Only)
CAUTION: DO NOT connect the power supply to the device until it is completely
installed and all connections have been made.
Power for the B-540-EXT-330-RS-IPW receiver can be supplied via a remote power source
when use of either PoC or the Latch-Locking Power Jack is not desired. The connection is a 2
conductor removable plug located on the rear of the B-540-EXT-330-RS-IPW receiver. The
recommended cabling is one 18 gauge per leg or two 22/ 24 gauge per leg.
Observe the connections polarity markings. Reversing the polarity may cause damage to the
product.
FIGURE 15: Remote Power Pin Out
The included WPS-ACC-PWR-DC Power Plug can be used to convert the single plug of a power
supply to 2 wires. This eliminates the need to cut the wires on the end of a power supply.
FIGURE 16: Power Plug
-(GND)
+(POS)
Page 15
15
7. SPECIFICATIONS
Technical Transmitter Receiver
HDMI Compliance 4K Ultra HD with Full 3D Support
HDCP Compliance Yes
Video Bandwidth 10.2 Gbps
HDMI over UTP
Transmission
1080i/720p 24-bit color: 330’ (Cat 5e/6/6a/7)
Full HD 1080p 24-bit color: 330’ (Cat 5e/6/6a/7)
Full HD 1080p 36-bit color: 330’ (Cat 5e/6/6a/7)
Ultra HD 4K2K@30 Hz (4:4:4:) 230 ft (Cat 5e/6), 330 ft (Cat 6a/7)
Ultra HD 4K2K@60 Hz (4:2:0:) 230 ft (Cat 5e/6), 330 ft (Cat 6a/7)
Input TMDS Signal 1.2V (peak-to-peak)
Input DDC Signal 5V (peak-to-peak, TTL)
ESD Protection (1) Human body model: ±5kV (air-gap discharge) & ±8kV (contact
discharge) (2) Core chipset — ±8kV
IR Signal (Bidirectional) Carrier frequency: 20–60kHz
Connections Transmitter Receiver
HDBaseT Link 1x RJ45 1x RJ45
HDMI 1x HDMI Type A
(19-pin female)
1x HDMI Type A
(19-pin female)
IR Receiver (In) 1x 3.5mm Mono/Stereo 1x 3.5mm Mono/Stereo
IR Flasher (Out) 1x 3.5mmMono 1x 3.5mm Mono
RS-232 Pass-through DB-9 DB-9
Ethernet Pass-through RJ-45 RJ-45
Power Thread-Locking
Controls
DIP switch 1 IR RCVR PWR OFF/ON
DIP switch 2 RS-232 Pin Conguration (DTE or DCE)
DIP switch 3 RS-232 Operation Mode (SERVICE/LINK)
Mechanical Transmitter Receiver
Housing Metal enclosure
Dimensions 6.25"x3.1"x1.3"
3.48"x2.8"x0.66"
Weight 1.1 lbs.
Power Supply 12V DC, 2A
Power Consumption 12W (max)
Operation Temperature 32–104°F
Storage Temperature -4–140°F
Relative Humidity 20–90% RH (no condensation)
Certications and Compliance Product: CE, FCC, RoHS
Power Supply: CE, FCC, RoHS, UL
Page 16
Rev: 160817-1150
© 2016 Binary
8. SUPPORT
Phone: 866. 838.5052
For SnapAV customers, snapav.com
For Aisle 8 customers, onaisle8.com
9. WARRANTY
2-Year Limited Warranty
This Binary product has a 2-Year limited warranty. This warranty includes parts and labor
repairs on all components found to be defective in material or workmanship under normal
conditions of use. This warranty shall not apply to products that have been abused, modied
or disassembled. Products to be repaired under this warranty must be returned to SnapAV
or a designated service center with prior notication and an assigned return authorization
number (RA).
Loading...