Page 1
Source | Mute | 2ch
(HDMI Out Audio)
INSTALLATION
MANUAL
HDBaseT EXTENDER
B-520-EXT-330-RS-IP
Page 2
2
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of re or electric shock, read and follow all instructions and warnings in this
manual. Keep this manual for future reference.
1. Do not expose this apparatus to rain or moisture. Do not expose this equipment to dripping
or splashing, and ensure that no objects lled with liquids, such as vases, are placed on the
equipment. Do not use this apparatus near water.
2. Do not remove cover. No user serviceable parts inside. Refer servicing to qualied service
personnel.
3. Clean only with a dry cloth.
4. Do not block any ventilation openings. Install according to manufacturer’s instructions.
5. Do not install near any heat sources such as radiators, heat registers, stoves or other
apparatus (including ampliers) that produce heat.
6. Do not override the safety purpose of the polarized or grounding plug. A polarized plug has
two blades, one of which is wider than the other. A grounding plug has two matching blades
and a third grounding prong. The wide blade or the third prong is provided for your safety. If
the provided plug does not t into your outlet, consult an electrician for replacement of the
obsolete outlet.
7. Protect the power cord from being walked on or pinched, particularly at the plug end and
where the power cord is attached to the apparatus.
8. Only use attachments and accessories specied by the manufacturer.
9. Refer all servicing to qualied service personnel. Servicing is required when the apparatus
has been damaged in any way, such as when the power supply cord or plug is damaged,
liquid has been spilled on or objects have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, the apparatus does not operate normally, or it has been
dropped.
10. To completely disconnect this equipment from power, disconnect the power supply cord
from the power outlet.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
CAUTION
TO REDUCE THE RIS K OF ELECTRICAL
SHOCK:
DO NOT REMOVE COVER. NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Page 3
3
CONTENTS
1. Product Overview ..........................................................................................................................................................4
2. Features ...............................................................................................................................................................................4
3. Package Contents ............................................................................................................................................................4
4. Device Layout ....................................................................................................................................................................5
4.1. B-520-EXT-330-RS-IP Transmitter ............................................................................................................5
4.2. B-520-EXT-330-RS-IP Receiver ..................................................................................................................6
5. Installation ..........................................................................................................................................................................6
5.1. B-520-EXT-330-RS-IP Transmitter Installation....................................................................................6
5.2. B-520-EXT-330-RS-IP Receiver Installation ..........................................................................................7
6. Applications .......................................................................................................................................................................7
6.1. HDBaseT Link (RJ45) Connection ..............................................................................................................8
6.2. IR Control Connections ..................................................................................................................................8
6.2.1. Point-to-Point IR Control - Stereo (3.5mm) IR Receiver .....................................................9
6.2.2. Control System - Mono (3.5mm) IR Receiver ..........................................................................9
6.2.3. IR Flasher Out-3.5mm Mono – Transmitter and Receiver .................................................10
6.3. RS-232 Control Connections .......................................................................................................................10
6.3.1. RS-232 Control (DB-9) Connection ............................................................................................11
6.3.1.1. RS-232 Operation Mode ..............................................................................................................11
6.3.1.3. Firmware Update Operation .....................................................................................................12
6.4. IP Control Connections ..................................................................................................................................12
6.5. HDMI Out (Transmitter) .................................................................................................................................13
6.6. EDID Conguration ..........................................................................................................................................13
6.6.1. Auto EDID .............................................................................................................................................13
6.6.2. HDBT EDID ...........................................................................................................................................13
6.7. Latch-Locking Power Supply ........................................................................................................................14
7. Specications ....................................................................................................................................................................14
8. Support ...............................................................................................................................................................................15
9. Warranty .............................................................................................................................................................................15
Page 4
4
1. PRODUCT OVERVIEW
Welcome to Binary. This product is engineered to provide years of exceptional reliability. We
appreciate your business and we stand committed to providing our customers with the highest
degree of quality and service in the industry.
This device extends HDMI® over a single category cable using HDBaseT technology allowing
video and audio transmission to remote displays. In addition, the device is equipped with
bidirectional IR, RS-232, and IP over a single category cable.
This unit supports all HDMI dened audio and video formats, including 4K2K@30 Hz.
The Power over Cable (PoC) feature enables the extender to be powered from either end.
Additionally, the design has been improved to solve the clock-stretching issue that can arise
with cable boxes when used with HDBaseT extenders.
2. FEATURES
• Improved design to support clock-stretching issue
• Extends all HDMI formats up to:
Resolution Cat 5e/6/6a/7
1080i/720p 24-bit color 330'
Full HD 1080p 24-bit color 330'
Full HD 1080p 36-bit color 330'
Ultra HD 4K2K@30 Hz 330'
• Supports all HDMI supported audio formats, including DTS-HD Master and Dolby TrueHD
• Two selectable EDID options: Auto and HDBaseT output
• Bidirectional IR, RS-232, and IP
• PoC capable - can be powered from either the transmitter or receiver
3. PACKAGE CONTENTS
• 1x B-520-EXT-330-RS-IP Transmitter
• 1x B-520-EXT-330-RS-IP Receiver
• 1x 12V DC, 2A Power Supply
• 4x Mounting Ears
• 4x Mounting Screws
• 8x Rubber Feet
• 1x Installation Manual
• 1x Power Supply Label
• 2x HDBaseT Labels
Page 5
5
4. DEVICE LAYOUT
4.1. B-520-EXT-330-RS-IP Transmitter
Ethernet
123 4
ON
BA C D E F G H I K LJ M
Back of Transmitter Front of Transmitter
FIGURE 1: Transmitter Layout
A. Thread-locking Power Connector
Connect to the included 12V DC, 2A power supply
B. Power LED
Lights up blue when the unit has power
C. HDMI Out
HDMI Output to connect to the HDMI input of a sink(display)
D. HDMI IN
HDMI Input to connect to the HDMI output of a source
E. IR Flasher
IR output to connect to IR Flasher
F. IR Receiver
IR input to connect to IR Receiver or to output of a control system
G. IR Flasher level
Adjusts the intensity of the IR Flasher output
H. Ethernet (RJ45)
To communicate IP data between Transmitter and Receiver
I. DIP Switches
IR RCVR PWR OFF/ON
OFF to connect to control system | ON to connect to IR Receiver
DCE/DTE
To select if serial (RS232) communication via DB-9 is in DTE or DCE mode
LINK/SERVICE DIP
LINK for passthrough (normal) operation | SERVICE for rmware operation
AUTO EDID/HDBT EDID
AUTO to set EDID to lowest common resolution | HDBT to set EDID to resolution of sink at
other end
J. RS-232
To communicate RS-232 command with the receiver when connected to a control system
K. HDBaseT (RJ45)
To connect to the HDBaseT RJ45 port on receiver
L. Link LED
Lights up green when synced with receiver
M. Update (mini USB port)
To connect mini USB cable when updating rmware
Page 6
6
4.2. B-520-EXT-330-RS-IP Receiver
Back of Receiver Front of Receiver
1ON23
Ethernet
BA C D E F G IH J K
FIGURE 2: Receiver Layout
A. Thread-locking Power Connector
Connect to the included 12V DC, 2A power Supply
B. Power LED
Lights up blue when the unit has power
C. HDMI Out
HDMI Output which could be connected to the HDMI input of a sink (display)
D. IR Flasher
IR output to connect to IR Flasher
E. IR Receiver
IR input to connect to IR Receiver or to output of a control system
F. IR Flasher level
Adjusts the intensity of the IR Flasher output
G. Ethernet (RJ45)
To communicate IP data between Transmitter and Receiver
H. DIP Switches
IR RCVR PWR OFF/ON
OFF to connect to control system | ON to connect to IR Receiver
DCE/DTE
To select if serial (RS232) communication via DB-9 is in DCE or DTE mode
LINK/SERVICE DIP
LINK for passthrough (normal) operation | SERVICE for rmware operation
I. RS-232
To communicate RS-232 command with the transmitter when connected to a control
system
J. HDBaseT (RJ45 )
To connect to the HDBaseT RJ45 port on transmitter
K. Link LED
Lights up green when synced with receiver
5. INSTALLATION
CAUTION: Do not connect power to the device until all other connections are made and the
unit is installed.
5.1. B-520-EXT-330-RS-IP Transmitter Installation
1. Run category cable from the location of the transmitter to the remote location of the receiver.
2. Mount the transmitter in the desired location.
Page 7
7
3. Connect the HDMI Out of a source component using an HDMI cable.
4. Connect the RS-232 DB-9 from a control system if being used.
5. Connect an IR control system to the IR receiver and/or IR asher if being used. Refer to Section 6.2.
6. Connect the patch cable from the router or network switch to the ethernet port (RJ45).
7. Connect the 12V DC, 2A power supply to the latch-locking power jack, unless PoC is being
used to send power from the receiver. DO NOT plug the power supply into an AC outlet
until Receiver Installation is completed.
5.2. B-520-EXT-330-RS-IP Receiver Installation
1. Run category cable from the location of the transmitter to the remote location of the receiver.
2. Mount the receiver in the desired location.
3. Connect the category cable to the receiver.
4. Connect an IR asher and/or IR receiver if being used. Refer to Section 6.2.
5. Connect an HDMI cable from the HDMI Out of receiver to the display.
6. Connect the RS-232 DB9 to an RS-232 controllable source if being used.
7. Connect the ethernet RJ45 to an ethernet enabled device if being used.
8. Connect the 12V DC, 2A power supply to the latch-locking power jack, unless PoC is being
used to send power from the transmitter.
9. Connect the power supply to the AC outlet.
6. APPLICATIONS
HDTV
PLAY
HDTV
Ethernet
123 4
ON
1ON23
Ethernet
FIGURE 3 : Application Diagram
Note: When a power supply is connected to either the transmitter or receiver, the HDBaseT
link sends power to the other unit. Only one unit requires a power supply to be connected.
HDMI Source
AC
Power
Back Front
B-520-EXT-330-RS-IP Receiver
B-520-EXT-330-RS- IP Transmitter
Page 8
8
6.1. HDBaseT Link (RJ45) Connection
This device is specied to operate with category cables for communication between the transmitter
and receiver. The transmission path may include a maximum of two keystones and two patch cables,
as long as the total length does not exceed 330' for category cable.
Pi
n 1White/OrangePin 5White/Blue
Pi
n 2OrangePin 6Green
Pi
n 3White/Green Pin 7White/Brown
Pi
n 4BluePin 8Brown
TIA/EIA Standard 568-B (Gold Pins Facing Up)
FIGURE 4: RJ45 Connections
Note: The HDBaseT Link RJ45 connection includes a 12V signal. Do not connect anything to
this port other than an HDBaseT transmitter or receiver.
6.2. IR Control Connections
Bidirectional IR signals can be transmitted between transmitter and receiver through category
cable. The IR signal can be generated either from a powered receiver or from a control system.
The following section describes these two use cases.
CAUTION: Pinout congurations for IR receivers and control systems vary. Before connecting
to this input, review this section carefully in order to match the pinouts for the device.
IR OutputsIR Inputs
PLAY
HDTV
Ethernet
123 4
ON
1
O
N
23
Ethernet
C A
D
C B
FIGURE 5: IR Connections
Note: Arrow direction indicates signal ow.
IR Receiver In-3.5 mm Mono—See Section 6.2.2
IR Receiver In-3.5 mm Stereo—See Section 6.2.1
IR Flasher Out-3.5 mm Mono—See Section 6.2.3
D HDBaseT Link category cable (RJ45)—See Section 6.1
B-520-EXT-330-RS-IP Receiver
B-520-EXT-330-RS-IP Transmitter
IR Processor/ Controller
HDMI Source
HDBaseT
Back Front
Page 9
9
6.2.1. Point-to-Point IR Control - Stereo (3.5mm) IR Receiver
When using a powered IR receiver, the DIP switch for IR RCVR PWR should be set to ON. In
this case a 3.5mm (1/8") stereo jack has to be used to send 9V DC power to the receiver.
CAUTION: DO NOT connect a mono cable to this connection as damage may occur.
123 4
ON
1ON23
9V DC (Sleeve)
GND (Ring)
IR Signal (Tip)
FIGURE 6: Point-to-Point IR settings
6.2.2. Control System - Mono (3.5mm) IR Receiver
When using a control system which generates the signal through a mono jack, the IR RCVR
PWR switch should be in the OFF position.
123 4
ON
1ON23
GND (Sleeve)
IR Signal
(Tip)
FIGURE 7 : Control System IR settings
TRANSMITTER RECEIVER
Pinout Conguration
TRANSMITTER RECEIVER
Pinout Conguration
Page 10
10
6.2.3. IR Flasher Out-3.5mm Mono – Transmitter and Receiver
The IR Flasher level adjusts the intensity of the IR Flasher output
GND (Sleeve)
IR Signal
(Tip)
FIGURE 8: IR Flasher Out
6.3. RS-232 Control Connections
Bidirectional RS-232 signals are transmitted between the device transmitter and receiver over
the category cable. The transmitter may be connected to a control system and the receiver may
be connected to an RS-232 controllable device.
123 4
ON
1ON23
A
B
A B
FIGURE 9: RS-232 Connections
RS-232 Control (DB-9)- See Section 6.3.1
HDBaseT Link category - See Section 6.1
Pinout Conguration
B-520-EXT-330-RS-IP Transmitter
RS-232 Controllable
Device
Control
System
B-520-EXT-330-RS-IP Receiver
Page 11
11
6.3.1. RS-232 Control (DB-9) Connection
To eliminate the need to make crossover or null modem cables, the RS-232 pinouts can be
congured for DCE or DTE. Set switch 2 to DCE if the connected device is DCE, and to DTE if
the connected device is DTE.
Typically the control system will be DTE and the controlled device will be DCE, however,
devices may vary. Refer to the manual for the connected devices for proper pinout
conguration.
21 21
21 21
PIN FUNCTION
2 RxD (Data Receive)
3 TxD (Data Transmit)
5 GND
PIN FUNCTION
2 TxD (Data Transmit)
3 RxD (Data Receive)
5 GND
235
FIGURE 10: RS-232 Modes and Connections
DTE Mode
RS-232 DB-9 Pinouts
DCE Mode
TRANSMITTER
RECEIVER
Page 12
12
6.3.2. RS-232 Operation Mode / Firmware Update Operation
The RS-232 connection can also be used for rmware updates in addition to sending RS-232
signals. The DTE/DCE switch is used to set the RS-232 Mode.
Note: The SERVICE/LINK switch must set to LINK during normal RS-232 passthrough
operation.
To perform rmware updates, the DIP switches must be set to DTE and SERVICE. Detailed
instructions and updated rmware will be posted to www.snapav.com as they are released.
Note: The DIP switch should be set to LINK during normal operation.
123 4
ON
1ON23
FIGURE 11: Firmware Update settings
6.4. IP Control Connections
Bi-directional Ethernet signals are transmitted between the B-520-EXT-330-RS-IP Transmitter
and Receiver over the Cat5e/6 cable. The most common use is to send Ethernet signals for
Networked TVs or any device in the remote location that has an Ethernet connection. This
connection is only to be used for standard Ethernet signals and cannot be used for other
communication formats.
Ethernet Enabled Device
A A
B
B
Network Router or Switch
Ethernet
1 2 3 4
ON
Ethernet
1 2 3 4
ON
FIGURE 12
Ethernet (RJ45)
HDBaseT Link category - See Section 6.1
Note: This connection is for 10/100 BaseT Ethernet ONLY. DO NOT connect a cable from an
HDBaseT port.
TRANSMITTER RECEIVER
TRANSMITTER RECEIVER
TRANSMITTER RECEIVER
Page 13
13
6.5. HDMI Out (Transmitter)
We recommend using an HDMI cable that is one meter or less to ensure the highest signal
quality. This HDMI Out is used to connect to local TV/displays.
6.6. EDID Conguration
There are two EDID operating modes available for HDMI loopout. The EDID setting
determines if the source connected to the HDMI input chooses the EDID from the display
connected to the HDMI out on the transmitter and/or the display connected to the HDMI out
on the receiver
6.6.1. Auto EDID
When the EDID DIP switch is set to AUTO, the lowest common EDID setting between the
display connected to the transmitter and the display connected to the receiver will be applied
to both displays.
123 4
ON
FIGURE 13: Auto EDID Mode
6.6.2. HDBT EDID
When the EDID DIP switch is set to HDBT, the EDID from the display connected to the receiver
will be applied to both displays.
123 4
ON
FIGURE 14: HDBT EDID Mode
TRANSMITTER
TRANSMITTER
Page 14
14
6.7. Thread-Locking Power Supply
This extender pair is Power over Cable capable and therefore can be powered from either
the transmitter or receiver. When a power supply is connected to either the transmitter or
receiver, the HDBaseT link sends power to the other end.
CAUTION: Do not connect the power supply to the device until it is completely installed
and all connections have been made.
7. SPECIFICATIONS
Technical Transmitter Receiver
HDMI Compliance HDMI 3D
HDCP Compliance Yes
Video Bandwidth 10.2 Gbps
HDMI over UTP Transmission Cat 5e/6/6a/7 1080i/720p 24-bit color: 330'
Full HD 1080p 24-bit color: 330'
Full HD 1080p 36-bit color: 330'
Ultra HD 4K2K@30 Hz 330'
Input TMDS Signal 1.2V (peak-to-peak)
Input DDC Signal 5V (peak-to-peak, TTL)
ESD Protection (1) Human body model: ±5kV (air-gap discharge) & ±8kV (contact
discharge) (2) Core chipset — ±8kV
IR Signal (Bidirectional) Carrier frequency: 20–60kHz
Connections
HDBaseT Link 1x RJ45 1x RJ45
HDMI 1x HDMI Type A
(19-pin female)
1x HDMI Type A
(19-pin female)
IR Receiver (In) 3.5mm Stereo/Mono 1x 3.5mm Stereo/Mono
IR Flasher (Out) 1x 3.5mmMono 1x 3.5mm Mono
RS-232 passthrough DB-9 DB-9
IP pass-through Ethernet Ethernet
Power Latch-Locking
Controls
DIP switch 1 IR RCVR PWR OFF/ON
DIP switch 2 RS-232 Pin Conguration (DCE /DTE)
DIP switch 3 RS-232 Operation Mode (SERVICE/LINK)
DIP switch 4 EDID – HDBT EDID/
AUTO EDID
Mechanical
Housing Metal enclosure
Dimensions 6.25" x 3.1" x 1.3"
Page 15
15
Technical Transmitter Receiver
Weight 1.1 lb
Power Supply 12V DC, 2A
Power Consumption 12W (max)
Operation Temperature 32–104°F
Storage Temperature -4–140°F
Relative Humidity 20–90% RH (no condensation)
Certications and Compliance Product: CE, FCC, RoHS
Power Supply: CE, FCC, RoHS, UL
8. SUPPORT
Need Help? Contact Tech Support!
If you need further clarication, please call tech support at 800.838.5052, or email support@
snapav.com. For more information, instructional videos, support documentation, and ideas,
visit our website and view your item’s product page at www.snapav.com.
9. WARRANTY
2-Year Limited Warranty
This Binary Product has a 2-Year limited warranty. This warranty includes parts and labor
repairs on all components found to be defective in material or workmanship under normal
conditions of use. This warranty shall not apply to products that have been abused, modied or
disassembled. Products to be repaired under this warranty must be returned to SnapAV or a
designated service center with prior notication and an assigned return authorization number
(RA).
Page 16
Rev: 150806-1100
© 2015 Binary
Loading...