Binary B-100-HDMATRIX-4X4, B-100-HDMATRIX-8X8 Owner's Manual

B-100-HDMATRIX-4X4 / B-100-HDMATRIX-8X8
OWNER’S MANUAL
>>
BINARY HD MATRIX SWITCHER
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of re or electric shock, do not expose this apparatus in or near
1. Read and keep these instructions for future reference.
2. Do not use this apparatus near water.
3. Clean only with a dry cloth.
4. Do not block any ventilation openings. Install according to manufacturer’s instructions.
5. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (Including ampliers) that produce heat.
6. Do not override the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades - one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.
7. Protect the power cord from being walked on or pinched particularly
at plug, convenience receptacles, and the point where it exits from the apparatus.
8. Only use attachments/accessories specied by the manufacturer.
9. To completely disconnect this equipment from the AC mains, disconnect the power
supply cord plug from the AC receptacle.
10. This is CLASS II apparatus with double insulation, and no protective earth provided.
CAUTION
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK.
DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated dangerous voltage within the product’s enclosure that may be of sucient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
TABLE OF CONTENTS
1 OVERVIEW ........................................................................................................... 4
1.1 Features...........................................................................................................................................4
1.2 PACKAGE CONTENTS ..................................................................................................................4
2 FRONT AND REAR PANEL ................................................................................... 5
2.1 Front Panel B-100-HDMatrix-4x4 ...........................................................................................5
2.2 Front Panel B-100-HDMatrix-8x8 ...........................................................................................5
2.3 Rear Panel B-100-HDMATRIX-4x4 ..........................................................................................6
2.4 Rear Panel B-100-HDMATRIX-8x8 ..........................................................................................6
3 INSTALLATION ..................................................................................................... 7
3.1 Installation Considerations ......................................................................................................7
3.1.1 Rack Installation .......................................................................................................................7
3.2 Connections ..................................................................................................................................8
3.2.1 Basic Connections....................................................................................................................8
3.3 Control Ports .................................................................................................................................9
3.3.2 IR Receiver Connection ..........................................................................................................9
3.3.2.1 Stereo to Mono IR Adaptor ...............................................................................................9
3.3.2.2 Custom Cable Construction .............................................................................................9
3.3.3 RS-232 DB9 Serial Connection .......................................................................................... 10
4 EDID CONFIGURATION ...................................................................................... 11
4.1 Basic EDID Conguration ....................................................................................................... 11
4.2 Advanced EDID Conguration ............................................................................................. 12
4.2.1 Embedded EDIDs Defaults ................................................................................................. 12
4.2.1.1 Setting EDID for Single Input ......................................................................................... 13
4.2.1.2 Setting EDID for All Inputs .............................................................................................. 13
4.2.2 Learning EDID .........................................................................................................................14
4.2.2.1 Learning EDID to All Inputs............................................................................................. 14
4.3 EDID Status .................................................................................................................................. 15
5 ADVANCED CONFIGURATION ........................................................................... 15
5.1 PC Conguration Other Settings ......................................................................................... 15
5.1.1 IR Receiver Active ................................................................................................................... 15
5.1.2 Front Panel Power Button Active ..................................................................................... 15
5.1.3 HDMI Input EQ Setting ........................................................................................................ 15
6 OPERATION AND CONTROL .............................................................................. 16
6.1 IR Remote ..................................................................................................................................... 16
6.1.1 Route Inputs to Outputs...................................................................................................... 16
6.1.2 Turn O (Mute) Outputs ...................................................................................................... 17
6.1.4 Resetting to Factory Defaults ............................................................................................ 17
7. SPECIFICATIONS................................................................................................ 18
8. WARRANTY ........................................................................................................ 19
B-100 HDMATRIX Installation and Users Manual 4X4 & 8X8
pg.4
1. OVERVIEW
Welcome to Binary™ - This product is engineered to provide years of exceptional reliability. Binary™ is one of the most highly regarded brands available today and stands committed to providing customers with the highest degree of quality and service in the industry.
The B-100-HDMATRIX-4x4 and B-100-HDMATRIX-8x8 are state-of-the-art HDMI switchers providing true Matrix Routing for HDMI signals. With features such as HDMI 1.4a 3D support, sophisticated EDID handling, IR, RS232 and Ethernet (8x8 only) control, they are ideal for residential and commercial media distribution systems.
1.1 FEATURES
· (4) HDMI Sources by (4) HDMI Outputs {B-100-HDMATRIX-4x4}
· (8) HDMI Sources by (8) HDMI Outputs {B-100-HDMATRIX-8x8}
· Outputs can show the same or dierent sources simultaneously
· Video resolutions up to 1080p/60 with 36bit color
· Digital Audio up to 7.1 Channels
Dolby TrueHD Dolby Digital Plus DTS-HD Master DTS-HD Dolby Digital EX DTS-ES Dolby DigitalDTSLPCM
· Support for HDMI 1.4a 3D formats
· Sophisticated EDID handling including Embedded, Learned and Auto modes
· HDMI or DVI with adapter (not included)
· IR Control from integrated receiver or 3.5mm input
· Home Automation Control via IR, RS-232 and Ethernet (8x8 only)
· PC Setup and Conguration
· HDCP 2.0 Compliant
· CEC Compliant
1.2 PACKAGE CONTENTS
(1) B-100-HDMATRIX-4x4 or B-100-HDMATRIX-8x8 (2) Rack ears for mounting (1) IR Remote (1) Power supply
• B-100-HDMATRIX-4x4, 5V 4A
• B-100-HDMATRIX-8x8, 12V 5A
(1) IR Adapter for Automation Systems (1) User Manual (1) CD Rom containing documentation and software
B-100 HDMATRIX Installation and Users Manual 4X4 & 8X8
© 2011 Binary
pg.5
1 2 3 4
5
1 2 3 4
5
2. FRONT AND REAR PANEL
2.2 Front Panel B-100-HDMatrix-8x8
2.1 Front Panel B-100-HDMatrix-4x4
1. Power: Power ON/OFF switch
2. Source Status (LED on = Source is ON and sending a signal)
3. Output: Displays the last selected Output
4. Input: Displays the last selected Input
5. IR Receiver Window
1. Power: Power ON/OFF switch
2. Source Status (LED on = Source is ON and sending a signal)
3. Output: Displays the last selected Output
4. Input: Displays the last selected Input
5. IR Receiver Window
B-100 HDMATRIX Installation and Users Manual 4X4 & 8X8
pg.6
2.4 Rear Panel B-100-HDMATRIX-8x8
2.3 Rear Panel B-100-HDMATRIX-4X4
1. +12V DC interlocked power jack
2. RS-232 control port (DB9)
3. HDMI Inputs 1 through 8
4. HDMI Outputs 1 through 8
5. External IR Receiver (3.5mm Stereo)
6. Ethernet Port
2
3
4
1
5
6
1 2
3 4 5
1. +5V DC interlocked power jack
2. RS-232 control port (DB9)
3. HDMI Inputs 1 through 4
4. HDMI Outputs 1 through 4
5. External IR Receiver (3.5mm Stereo)
B-100 HDMATRIX Installation and Users Manual 4X4 & 8X8
© 2011 Binary
pg.7
3. INSTALLATION
3.1 Installation Considerations
Binary HDMatrix switchers are designed with unsurpassed technology to provide superior performance. However, where you install the switcher can have a large eect on the performance that you receive, and the life of the unit. Here are some guidelines to follow when installing a B-100- HDMatrix Switcher.
• Be sure that the unit is in a well-ventilated area that provides adequate cooling.
• Do not block the cooling vents located on both sides of the unit.
• Do not place the unit on carpeting or any similar material.
• Do not install the unit near a source of heat, or in an extremely humid or wet location.
• If your installation lacks good air ow (such as solid cabinet doors or wall-mounted
racks), it may be necessary to create ventilation to allow outside air into the space.
• Allow a minimum of 3” of free air space on either side of the unit. (Does not apply to
rack mounting)
• Allow a minimum of 2” of depth behind unit to accommodate cables and connectors.
• When placing on a cabinet shelf, position the unit with all feet resting on a
solid level surface.
3.1.1 Rack Installation
The B-100-HDMATRIX can be mounted in a rack with the front or rear panel facing outward. This allows for easy access to the connections for installations that do not require the front panel of the unit to be accessed. When mounting the rear panel facing out, it is recommended that an IR receiver or Automation system is used.
B-100 HDMATRIX Installation and Users Manual 4X4 & 8X8
pg.8
3.2 CONNECTIONS
3.2.1 Basic Connections
HDMI Sources
• Blu-ray /DVD Player
• Game Console
• Cable/Sat HD DVR
• PC
Video Displays
• HD Flat-Panel
• HD Projector
• HD Flat Panel
• HDMI Extender
Control Devices
• IR Receiver
• Home Automation System
Examples
HDTV
Home Automaon
HDTV HDTV
HDMI Extender
Receiver
HDMI Extender
Transmier
HD Projector
Game
Console
Blu-ray/DVD
Player
Cable/Sat
HD DVR
IR Receiver
PC
B-100 HDMATRIX Installation and Users Manual 4X4 & 8X8
© 2011 Binary
pg.9
3.3.1 IR Receiver Connection
Pin out congurations for IR receivers and Automation Systems vary. Before connecting to this input, review this section carefully in order to match the pin outs for the HDMatrix. Before connecting an IR Receiver or to an IR Automation System, verify that the HDMatrix is OFF to ensure proper operation when connected.
3.3.2 Connecting to an IR Automation System/Connecting block
When connecting to an IR Automation System or connecting block, the 12V DC (Sleeve) must not be connected. Connections of this type require the use of the included Stereo to Mono dongle or a custom cable made. A mono 3.5mm cable should not be used as it will short out the 12 VDC to GND, and will make the connection inoperable.
IR Signal Tip
GND Ring
12v DC Sleeve
IR Signal
(Tip)
GND
(Ring)
12v DC
(Sleeve)
IR Signal (Tip)
12V DC (Sleeve)
GND (Ring)
To B-100-HDMATRIX
To IR Control System/
Connecting Block
IR Signal (Tip)
GND (Sleeve)
IR Signal (Tip)
(Tip)
12V DC (Sleeve)
GND (Ring)
(
Sleeve
)
IR Signal (Tip)
12V DC (Sleeve)
GND (Ring)
To B-100-HDMATRIX
IR Signal (Tip)
GND (Sleeve)
To IR Control System/
Connecting Block
3.3 Control Ports
3.3.2.1 Stereo to Mono IR Adaptor
3.3.2.2 Custom Cable Construction
B-100 HDMATRIX Installation and Users Manual 4X4 & 8X8
pg.10
3.3.3 RS-232 DB9 Serial Connection
The Binary™ HDMatrix receives control data on pin 2 (Rxd - Data Receive) and transmits control data on pin 3 (TxD - Data Transmit). The connection cable between the HD MATRIX and the Automation System will need to be congured so that pin2 (RxD) on the HD MATRIX is connected to the Automation Systems Txd pin, and pin3 (TxD) on the HD MATRIX is connected to the Automation Systems Rxd (Receive Data) pin. See below for details. Conguration for the Automation System control ports can vary. Refer to the documentation for the Automation System you are using to ensure proper connection and conguration. This port is also used to communicate with a PC when using the PC Conguration Utility. Refer to the Conguration Utility manual for details.
PIN FUNCTION
2 RxD (Data Receive)
3 TxD (Data Transmit)
5 GND
3 25
DB9 Female Connection
RxD (Data Receive)
TxD (Data Transmit)
GND
In addition to the RS-232 DB9, the B-100-HDMATRIX-8x8 adds an Ethernet port that can be used to control the device using Telnet Protocol. This port follows TIA 568 A/B standards; refer to these when creating wiring.
B-100 HDMATRIX Installation and Users Manual 4X4 & 8X8
© 2011 Binary
pg.11
4 EDID Conguration
While most HDMI sources can provide full HD, the displays used within an installation may not support the features available from the source. In these cases, the display may not play the content being provided by the source. It is necessary to make sure each source will provide a Video and Audio format compatible with all displays that will view that source. This can be accomplished by managing the EDIDs stored in the HDMatrix for each source. The stored EDID is per source, so all display locations will see the same resolution and have the same audio format when that source is selected.
The following section explains conguring EDIDs via the IR Remote. Before conguring the EDID be sure to refer to the source(s) and display(s) manuals for available features and resolutions for each device.
While all EDID, congurations are available via the remote, a PC utility is also available on the HDMatrix product pages, which can be found on the manufacturer’s website (www.snapav.com).
When conguring EDIDs via IR, the ENTER key must be pressed within 10 seconds of the last command in order to be processed.
Source Setup
Most sources have selections for Audio format and Video resolution that can x the output so that it will not change based on the EDID supplied by the connected display or switch. Check each source and conrm that the audio format and video resolution are set so that they will change based on the EDID
negotiation. Normally this is a setting called “Auto” or similar.
Display Setup
It is recommended that the Consumer Electronics Control (CEC) is turned OFF in all displays when using the HDMatrix. This will provide for proper communications of video/audio signals and allow EDIDs to function at their optimum performance. Refer to the display’s manual for information on how to turn this function OFF.
Verify that all displays are connected to the HDMatrix before continuing with EDID Conguration.
4.1 Basic EDID Conguration
The quickest and easiest method for conguration is to use Auto EDID. When used, the HDMatrix looks at the EDID from each of the connected displays. It uses the lowest common denominator for video resolution and audio format to create a new EDID , which is saved to all Inputs.
Note: Auto EDID sets audio to 2ch for all inputs regardless of the capability of the connected displays. If multi-channel audio is desired, embedded EDIDs or Learned EDIDs will need to be used.
When to Use Auto EDID
• When all sources will be available on all displays.
• Every display in the system accepts the same video and audio resolution from the sources.
• As a rst step to conguration following up with advanced methods for particular displays and
dedicated sources.
For advanced EDID conguration when using legacy display and/or dedicated sources, use embedded EDIDs or learning as described in the following sections:
B-100 HDMATRIX Installation and Users Manual 4X4 & 8X8
pg.12
Sets EDID Based on All Connected Displays
Display Readout (Example)
1. Press DEFAULT
E-
2. Press Number Key 9
AA
4. Press ENTER
A0
Setting Auto EDID via IR Remote
4.2 Advanced EDID Conguration
4.2.1 Embedded EDIDs Defaults
The B-100-HDMATRIX switchers contain 8 representative ‘embedded’ EDIDs that may be assigned to Inputs. These EDIDs dene groups of video and audio capabilities that are useful for conguring sources in most systems.
When to Use Embedded EDIDs
• When audio and video characteristics of displays are known and compatible with
the an Embedded EDID
Explanation of Embedded EDIDs
Video Resolution in the Embedded EDIDs is the highest resolution a connected source
will output; for example, if the source is capable of 1080P@60, it will be required by EDIDs 1-6 to provide that resolution. However, if the source is only capable of 1080i, it will output 1080i, etc. It is assumed that any display that can accept the specied Video Resolution can also accept all standard video resolutions less than that specied.
Color Depth is the maximum number of bits used to encode color. 24bit color depth is 8bits per color (Red, Blue, Green) and 36bit color depth is 12 bits per color. When 36bit color is used, the bandwidth increases substantially. This will dramatically reduce the distance between the switch and the display when using an extender.
3D indicates that the source can output 3D if it is available in the content.
Audio Format indicates the maximum number of audio channels, as well as the audio format that the source is allowed to output. For an Embedded EDID with 7.1ch Audio Format, the source device will output the highest audio possible based on the content. For example, if 7.1ch is not available and 5.1ch is, the output will be 5.1ch. The same holds true if 2ch is the only audio available from the source.
Embedded EDIDs with 2Ch will limit output of the source to 2ch regardless of the formats available in the content.
Embedded EDIDs 7 and 8 are provided for legacy displays that can only accept resolutions up to a maximum of 1080i / 720p. The 1080i is listed rst since almost all older HD displays can accept 1080i, but not all can accept 720p. For these two Embedded EDIDs, (7&8) the source will output 1080i. Should 1080i not be available, the source will output 720p. There is a possibility that 720p may not work for a very small number of displays currently in use. If you have such a display, you will need to use a Learned EDID (see below) from the display to store in the Input EDID of any sources that will be routed to that display.
B-100 HDMATRIX Installation and Users Manual 4X4 & 8X8
© 2011 Binary
pg.13
Embedded EDID Resoluon Color Depth Audio
1
1080p@60Hz 24-Bit 7.1ch
2
1080p@60Hz 24-Bit 2ch
3
1080p@60Hz 24-Bit 3D 7.1ch
4
1080p @60Hz 24-Bit 3D 2ch
5
1080p@60Hz 36-Bit 3D 7.1ch
6
1080p@60Hz 36-Bit 3D 2ch
7
1080i@60Hz / 720p@60Hz 24-Bit 7.1ch
8
1080i@60Hz/ 720p@60Hz 24-Bit 2ch
4.2.1.1 Setting EDID for Single Input
4.2.1.2 Setting EDID for All Inputs
Example: Input =1 Embedded EDID=4
Display Readout (Example)
1. Press DEFAULT
E-
2. Press Number Key (1-8) to select one Embedded EDID
4A
3. Press INPUT
4A
4. Press Number Key (1-8) to select the Input to which the EDID is applied
41
5. Press ENTER
(success) (fail)
-­FF
Example: Input=All Embedded EDID=4
Display Readout (Example)
1. Press DEFAULT
E-
2. Press ALL to select all Inputs
E-
3. Press Number Key (1-8) to select Embedded EDID
4A
4. Press ENTER
(success) (fail)
-­FF
B-100 HDMATRIX Installation and Users Manual 4X4 & 8X8
pg.14
4.2.2 Learning EDID
For more advanced EDID conguration, learning can be used to assign EDIDs. When used ,the EDID from a particular display is assigned to a particular source or all sources. This is useful when the system contains a display that may not output the highest resolution available from the sources.
When to Use Learned EDIDs
• An older display does not work properly with any of the embedded EDIDS.
• When the source is a PC, it may be necessary to use a learned EDID.
• Learning EDID to a Single Input.
Example: Input =1 EDID Learned from Output 4
Display Readout (Example)
1. Press LEARN
L.-.
2. Press OUTPUT
1A
3. Press Number key (1-8) to select the Output the EDID is learned from
14
4. Press INPUT
L-
5. Press Number Key (1-8) to select the Input to which the EDID is applied
1A
6. Press ENTER
(success) (fail)
-­FF
Example: Input=All EDID Learned from Output 4
Display Readout (Example)
1. Press LEARN
L.-.
2. Press OUTPUT
3. Press Number Key (1-8) to select the Output the EDID is learned from
4
4. Press ENTER
(success) (fail)
-­FF
4.2.2.1 Learning EDID to All Inputs
Note that learning the EDID for a display to all sources is the same as using Auto EDID.
B-100 HDMATRIX Installation and Users Manual 4X4 & 8X8
© 2011 Binary
pg.15
4.3 EDID Status
Once EDIDs are congured, the assigned EDID for sources can be reviewed to ensure that the desired output is congured or for troubleshooting.
Example: Input=3
Display Readout (Example)
EDID 5 Assigned from Embedded
EDID Table
EDID Learned from Output 4
1. Press STATUS
-- --
2. Press INPUT
-- --
3. Press Number Key (1-8)to select the desired Input
-3 -3
4. Press ENTER
5.3. 4.3
• If the second digit (the Input being queried) has a dot after it, then the rst digit is
the EDID number from the Embedded EDID table.
• If the second digit (the Input being queried) does not have a dot after it, then the
rst digit is the Output the EDID was learned from.
5 Advanced Conguration
During the installation of an HDMatrix, there are settings that provide Advanced Conguration above the use of the remote. These allow for ne tuning the HDMatrix when used under certain conditions and the settings listed below are not available from the remote.
For more information refer to the Conguration Utility manual available on the SnapAV website
5.1 PC Conguration Other Settings
The following settings can be found in the PC Conguration Utility Other Settings menu.
5.1.1 IR Receiver Active
Use this setting to disable the front panel IR receiver to avoid IR command conicts and prevent IR ooding of the HDMatrix. When IR is disabled, RS232 or IP must be used to control the HDMatrix.
5.1.2 Front Panel Power Button Active
Use this feature to disable/Enable the front panel power button of the HDMatrix when using an Automation System. This will prevent the HDMatrix from being powered OFF and preventing control of the device from an automation system UI.
5.1.3 HDMI Input EQ Setting
Use these settings when an HDMI image contains video noise and artifacts that can occur during switching or viewing some HDMI sources or displays. Each input can be set to High when video noise is present. We recommend that this be set to LOW as a starting point, and only changed should video noise be present on a particular input.
B-100 HDMATRIX Installation and Users Manual 4X4 & 8X8
pg.16
6 OPERATION AND CONTROL
6.1 IR Remote
Key Funcon
1
ON Power on the matrix switcher
2
OFF Enter standby mode
3
Number Keys 1-9 Select a number
4
10+ Not Used
5
All Select all Inputs or Outputs
6
Enter* Enter to trigger the previous seng
7
OUTPUT Begin output selecon
8
INPUT Begin input selecon
9
OUTPUT OFF Turn o/Mute the selected Output
10
STAT US Present EDID or Output status
11
LEARN Learn EDID from one output
12
DEFAULT Begin Embedded EDID Selecon
13
CLEAR Clear the former IR operaon procedure which user just
pressed but has not yet applied by pressing ENTER
*The ENTER key must be pressed within 10 seconds of the last command in order to be processed.
POWER
1
ON OFF
23
OUTPUT
INPUT
OUTPUT
OFF
STATUS LEARNDEFAULT CLEAR
ALL
456
78
10+
ENTER
9
1 2
3
45 6
7
8
9
10 11 12 13
Input to Single Output Example: Output=3 Input=4
Display Readout (Example)
1. Press OUTPUT
--
2. Press Number Key (1-8) to select Output
3-
3. Press INPUT
3-
4.Press Number Key (1-8) to select Input
34
5. Press ENTER
34
6.1.1 Route Inputs to Outputs
Input to All Outputs Example: Output=All Input=4
Display Readout (Example)
1. Press OUTPUT
--
2. Press ALL to select all Outputs
A-
3. Press INPUT
A-
4. Press Number Key (1-8) to select Input
A4
6. Press ENTER
44
B-100 HDMATRIX Installation and Users Manual 4X4 & 8X8
© 2011 Binary
pg.17
6.1.2 Turn Off (Mute) Outputs
6.1.3 Display Status
6.1.4 Resetting to Factory Defaults
This procedure resets the B-100-HDMATRIX to factory defaults: EDIDs - 1080i Stereo (embedded 8), I/O - All Outputs set to Input 1, DHCP (8x8 only) - Enabled.
Note that resetting factory defaults can take up to 2 minutes to complete.
Mute one Output Example: Output=1
Display Readout (Example)
1. Press OUTPUT
--
2. Press Number Key (1-8) to select Output
1-
3. Press OUTPUT OFF
10
4. Press ENTER
10
Mute All Outputs
Display Readout (Example)
1. Press OUTPUT
--
2. Press ALL to select All Outputs
A-
3. Press OUTPUT OFF
A0
4. Press ENTER
40
Example: Input=3
Display Readout (Example)
Example Out-
put=3, Input=4
Example Out-
put=3 Muted
1. Press STATUS
-- --
2. Press OUTPUT
-- --
3. Press Number Key (1-8) to select one Output
3- 3-
4. Press ENTER
34 30
Display Readout
(Example)
1. Press DEFAULT
E-
2. Press DEFAULT
--
3. Press DEFAULT
--
4. Press DEFAULT
DD
5. Press ENTER
D-
B-100 HDMATRIX Installation and Users Manual 4X4 & 8X8
pg.18
7. SPECIFICATIONS
B-100-HDMATRIX-4x4 B-100-HDMATRIX-8x8
Technical
Product Type True 4x4 HDMI matrix True 8x8 HDMI matrix
HDMI compliance Full HD 1080P60, Deep Color (36bit),
3D (1.4a 3D)
Full HD 1080P60, Deep Color (36bit), 3D (1.4a 3D)
HDCP compliance Version 2.0 Version 2.0
Video bandwidth Single-link 225MHz [6.75Gbps total
bandwidth]
Single-link 225MHz [6.75Gbps total
bandwidth]
Video support 1080p / 1080i / 720p /480p / 480i
up to 36-bit color
1080p / 1080i / 720p /480p / 480i up to 36-bit color
Audio support Mul-Channel up to 7.1:
Dolby TrueHD Dolby Digital Plus
DTS-HD Master
DTS-HD
LPCM
Dolby Digital EX DTS-ES Dolby Digital DTS
2ch: PCM
Mul-Channel up to 7.1:
Dolby TrueHD Dolby Digital Plus
DTS-HD Master
DTS-HD
LPCM
Dolby Digital EX DTS-ES Dolby Digital DTS
2ch: PCM
ESD protecon ESD: IEC 61000-4-2 Level 4 (15KV)
Surge: IEC 61000-4-5
ESD: IEC 61000-4-2 Level 4 (15KV) Surge: IEC 61000-4-5
Input 4x HDMI
1x RS-232
1x System IR (3.5mm jack)
8x HDMI
1x RS-232
1x System IR (3.5mm jack)
1x Ethernet Port
Output 4x HDMI 8x HDMI
HDMI Input selecon IR remote or RS-232 IR remote, RS-232 or Ethernet
IR remote control 21 buon remote for Setup and
Operaon
21 buon remote for Setup and Operaon
HDMI connector Type A [19-pin female] Type A [19-pin female]
RS-232 connector 9-pin DB9 female 9-pin DB9 female
Ethernet Connector
N/A
RJ45
Mechanical
HousingV Metal enclosure Metal enclosure
Dimensions (L x W x H)
Switcher 17” x 5.1” x 1.75” 17”x6.375”x1.75”
Package 21” x 10.4” x 3.1” 21”x10.4”x3.1”
Weight 4.4 lbs 5.4 lbs
Mounng 1RU rack-mount. Ears included 1RU rack-mount. Ears included
Power supply 5V 4A DC 12V 5A DC
Power consumpon 20 Was [max] 60 Was [max]
Operaon temperature 32~104°F] 32~104°F]
Storage temperature -20~60°C -4~140°F -20~60°C -4~140°F
Relave humidity 20~90% RH [no condensaon] 20~90% RH [no condensaon]
B-100 HDMATRIX Installation and Users Manual 4X4 & 8X8
© 2011 Binary
pg.19
8. WARRANTY
Two-Year Limited Warranty
This Binary™ product has a 2-year limited Warranty. This warranty includes parts and labor repairs on all components found to be defective in material or workmanship under normal conditions of use. This warranty shall not apply to products which have been abused, modied or disassembled. Products to be repaired under this warranty must be returned to SnapAV® or a designated service center with prior notication and an assigned return authorization number (RA).
© 2011 Binary
120531-1230
Loading...