Page 1
KVSP/TKVSP Owner’s Manual
BILLY GOAT KV VACUUM
Owner's Manual
KV600SP, KV650SPH, TKV650SPH
Accessories
ON BOARD
VACUUM
HOSE KIT
4"(102mm) x 7'
(2.13m)
For vacuuming
in hard to reach
areas.
P/N 891125
FELT
DEBRIS BAG
For use in
leaves and
grass in dusty
conditions.
P/N 891126
NOZZLE WEAR
GUARD KIT
For use in
increasing the
life of your
nozzle by
protecting it from
damage
P/N 891127
CASTER KIT
To allow for
easy rolling and
maneuverability
on smooth
surfaces.
P/N 891128
SHREDDER
KIT
Shreds
leaves,
reducing total
volume.
P/N 890209
KV LINER KIT
Increases the
life of the
housing by
protecting it from
damage.
P/N 891134
PROTECTIVE
COVER
Protects the
machine from
the environment
when not in use.
P/N 891136
Part No 891058 Form No F072508B
1
Page 2
KVSP/TKVSP Owner’s Manual
ABOUT THIS MANUAL
THANK YOU for purchasing a BILLY GOAT
manufactured to provide years of reliable and productive service. This manual provides complete operating and
maintenance instructions that will help to maintain your machine in top running order. Read this manual carefully
before assembling, operating, or servicing your equipment.
®
KV Vacuum. Your new machine has been carefully designed and
CONTENTS
SERIAL PLATE DATA AND SPECIFICATIONS 3
GENERAL SAFETY 4
SOUND AND VIBRATION 6
INSTRUCTION LABELS 7
PACKING CHECKLIST & ASSEMBLY 8
OPERATION 9-10
MAINTENANCE 11
TROUBLESHOOTING AND WARRANTY PROCEDURE 12
MAINTENANCE RECORD 13
ILLUSTRATED PARTS & PARTS LISTS 14-15
-5
Part No 891058 Form No F072508B
2
Page 3
SERIAL PLATE DATA
KVSP/TKVSP Owner’s Manual
Record the model number, serial number, date of
purchase, and where purchased.
Purchase Date:
Purchased From:
Specifications
Engine: HP 6.0 (4.47kW) 6.5 (4.85kW) 6.5 (4.85 kW)
Engine: Type B&S Quantum HONDA HONDA
Engine: Model 112K020124E1 GSV190AN1L GSV190AN1L
Engine: Fuel Capacity 1.5 qt. (1.4 L) 1.6 qt. (1.5 L) 1.6 qt. (1.5 L)
Engine: Oil Capacity 0.63 qt. (0.6 L) 0.58 qt (0.54L) 0.58 qt (0.54L)
Total Unit Weight: #129 (58.5 kg) #132 (58.9 kg) 141# (64 kg)
Overall Length 59” (1.5m) 59” (1.5m) 59” (1.5 m)
Overall Width 25.5” (.6 m) 25.5” (.6 m) 25.5” (.6 m)
Overall Height 42.75” (1.1m) 42.75” (1.1m) 42.75” (1.1 m)
Max. operating slope 200 200 200
Sound in accordance with
2000/14/EEC standards
Sound at operator’s ear 88 dBa 89 dBa 91 dBa
Vibration at operator position 0.71 g (6.96m/s2) 0.32 g (3.16m/s2) 0.43 g (4.25m/s2)
KV600SP KV650SPH TKV650SPH
109 dBa 109 dBa 112 dBa
Part No 891058 Form No F072508B
3
Page 4
KVSP/TKVSP Owner’s Manual
GENERAL SAFETY INSTRUCTIONS and SYMBOLS
The safety symbols shown below are used throughout this manual. You should become familiar with them before
assembling, operating, or servicing this equipment.
This symbol indicates important information that will prevent injury to yourself or others.
This symbol indicates ear protection is recommended when operating this equipment.
This symbol indicates eye protection is recommended when operating this equipment.
This symbol indicates gloves should be worn when servicing this equipment.
This symbol indicates that this manual and the engine manufacturer’s manual should be read
carefully before assembling, operation, or servicing this equipment.
This symbol indicates important information that will prevent damage to your BILLY GOAT ®
KV Vacuum.
This symbol indicates the engine oil level should be checked before operating this
equipment.
Read and make sure you thoroughly understand the following safety precautions before assembling, operating or
servicing this equipment:
READ this manual and the engine manufacturer’s manual carefully before assembling,
operating, or servicing this equipment.
EAR PROTECTION is recommended when operating this equipment.
EYE PROTECTION is recommended when operating this equipment.
BREATHING PROTECTION is recommended when operating this equipment.
EXHAUST from this product contains chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
DO NOT operate this equipment on any unimproved forested, brushy, or grass covered land
unless a spark arrester is installed on the muffler as required by Section 4442 of the
California Public Resources Code. The arrester must be maintained in good working order.
Other states may have similar laws. Federal laws apply on federal lands.
DO NOT run engine in an enclosed area. Exhaust gases contain carbon monoxide, an
odorless and possibly fatal poison.
Part No 891058 Form No F072508B
4
Page 5
KVSP/TKVSP Owner’s Manual
DO NOT run this equipment indoors or in any poorly ventilated area. Refueling outdoors is
recommended.
DO NOT refuel this equipment while the engine is running. Allow engine to cool for at least
two minutes before refueling.
DO NOT store gasoline near an open flame.
DO NOT remove gas cap while engine is running.
DO NOT start or operate engine if strong odor of gasoline is present.
DO NOT start or operate engine if gasoline is spilled. Move equipment away from spill until
gasoline has completely evaporated.
DO NOT smoke while filling the fuel tank.
DO NOT check for spark with spark plug or spark plug wire removed. Use an approved spark
tester.
DO NOT operate engine without a muffler. Inspect muffler periodically and replace if
necessary. If equipped with muffler deflector, inspect deflector periodically and replace if
necessary.
DO NOT operate engine with grass, leaves or other combustible material near the muffler.
DO NOT touch muffler, cylinder, or cooling fins when hot. Contact with hot surfaces may
cause severe burns.
DO NOT leave equipment unattended while in operation.
DO NOT park equipment on a steep grade or slope.
DO NOT operate equipment with bystanders in or near the work area.
DO NOT allow children to operate this equipment.
DO NOT operate equipment with guards removed.
DO NOT operate equipment near hot or burning debris or any toxic or explosive materials.
DO NOT operate equipment on slopes greater than specified in Specifications section of this
manual.
DO NOT place hands or feet underneath unit, or near any moving parts.
ALWAYS remove spark plug wire when servicing equipment to prevent accidental starting.
ALWAYS check fuel lines and fittings frequently for cracks or leaks. Replace if necessary.
ALWAYS keep hands and feet away from moving or rotating parts.
ALWAYS store fuel in approved safety containers.
WARNING: Important
Remove all rocks, wire, string, plastic, etc. that can present a hazard during work prior to
starting.
DO identify and mark all fixed objects to be avoided during work such as sprinkler heads,
water valves, buried cables, or clothes line anchors, etc.
Part No 891058 Form No F072508B
5
Page 6
KVSP/TKVSP Owner’s Manual
SOUND
SOUND LEVEL 92 dB(a) at Operator Position
Sound tests were conducted in accordance with 2000/14/EEC, and were performed on 7-25-07 under the
conditions listed below.
Sound power level listed is the highest value for any model covered in this manual. Please refer to serial plate on
the unit for the sound power level for your model.
General Conditions: Sunny
Temperature: 88
Wind Speed: 2 mph (3.8 kmh)
Wind Direction: South South East
Humidity: 44%
Barometric Pressure: 30.07”Hg (764 mm Hg
o
F (31.1oC)
)
VIBRATION DATA
VIBRATION LEVEL 0.34g (3.29m/s2)
Vibration levels at the operator’s handles were measured in the vertical, lateral and longitudinal directions using
calibrated vibration test equipment. Tests were performed on 12-19-2007 under the conditions listed below.
General Conditions: Sunny
Temperature: 50
Wind Speed: 4 mph (6.4kph)
Wind Direction: South Southeast
Humidity: 68%
Barometric Pressure: 30 Hg (101.6kpa
o
F (10oC)
)
INTENDED USE
INTENDED USE: This machine is designed for vacuuming leaves, grass clippings and other types of organic litter.
Debris mixed with cans, bottles and small amounts of sand can be vacuumed; however, it is not this machine's
primary purpose. Vacuuming cans, bottles and sand will affect the longevity of your machine.
Do not operate if excessive vibration occurs. If excessive vibration occurs, shut engine off immediately and check
for damaged or worn impeller, loose impeller bolt, loose impeller key, loose engine or lodged foreign objects.
Note: See parts list for proper impeller bolt torque specifications. (See trouble shooting section on page 12).
Part No 891058 Form No F072508B
6
Page 7
KVSP/TKVSP Owner’s Manual
INSTRUCTION LABELS
The labels shown below were installed on your BILLY GOAT ® KV Vacuum. If any labels are damaged or missing, replace them before operating
this equipment. Item numbers from the Illustrated Parts List and part numbers are provided for convenience in ordering replacement labels. The
correct position for each label may be determined by referring to the Figure and Item numbers shown.
LABEL DANGER KEEP HANDS LABEL EAR EYE BREATHING ITEM #20 DANGER FLYING DEBRIS
AND FEET AWAY P/N 890254 ITEM # 19 P/N 810736
ITEM #18 P/N 400424
LABEL READ MANUAL LABEL EXPLOSIVE FUEL CHIPPER WARNING LABEL LABEL DANGER GUARD
ITEM #17 P/N 890301 ITEM # 16 P/N 400268 ITEM #82 P/N 890152 (TKV ONLY) ITEM #39 P/N 900327
BAG FOLDING INSTRUCTIONS
LOCATED ON BAG
ENGINE LABELS
ENGINE and Transmission CONTROLS
HONDA BRIGGS & STRATTON
Read Owner’s Manual Before Operating.
Lire le manuel d’utilisation avant la mise en route.
Vor Inbetriebnahme Bedienungs - und Wartungsanleitung lesen.
Favor leer las instrucciones de operacion antes de operar el motor.
Consultare il Manuale Uso e Manutenzione prima dell utilizzo.
Las Skotselinstruktionen Innan Start.
Honda Throttle Control Briggs Throttle Control Bail Drive Engage/Disengage label
Part No 891058 Form No F072508B
7
Page 8
KVSP/TKVSP Owner’s Manual
PACKING CHECKLIST
Your Billy Goat KV Vacuum is shipped from the factory in one carton, completely assembled except for the
upper handle, debris bag, and bag quick disconnect.
READ all safety instructions before assembling unit.
TAKE CAUTION
cables and folded over
when removing the unit from the box the Handle Assembly is attached by
PUT OIL IN ENGINE BEFORE STARTING
PARTS BAG &
LITERATURE ASSY
Warranty card P/N- 400972, Owner’s Manual P/N-891058, Declaration of Conformity P/N-891057, Ty-wraps
900407 qty 2.
Quick disconnect
Use Ty-wraps
Boxing Parts
Checklist
Debris Bag
P/N-891132
Literature Assy
P/N-891121
Connector Quick
Disconnect
P/N-890176
Honda 6.5
GSV 190
Briggs & Stratton
6.0 HP Quantum
Fig. 2
ASSEMBLY
1. ASSEMBLE Lift upper handle (item 11), remove items 49, 50, & 51 from lower handle (item 10). Attach and
secure upper handle as shown using same hardware. Use the Ty-wraps from the parts bag to secure the throttle
cable and height adjustment cable at the bends on the upper handle.
2. UNFOLD the debris bag (item 21) and fasten bag neck to bag quick disconnect (item 12). Attach firmly to
housing exhaust (item 1) see fig. 2.
3. ATTACH bag to four posts (item 13), preassembled to upper handle.
4. CONNECT spark plug wire.
Part No 891058 Form No F072508B
8
Page 9
KVSP/TKVSP Owner’s Manual
OPERATION
Like all mechanical tools, reasonable care must be used when operating machine.
Inspect machine work area and machine before operating. Make sure that all operators of this
equipment are trained in general machine use and safety.
PUT OIL IN ENGINE BEFORE STARTING
STARTING
ENGINE: See engine manufacturer’s instructions for type and amount of oil and gasoline used. Engine
must be level when checking and filling oil and gasoline.
ENGINE SPEED
throttle to accomplish your current cleaning task.
FUEL VALVE
CHOKE
Honda-Place remote throttle in choke position
PRIMER
THROTTLE
TRANSMISSION: Engaged by pulling the clutch bail towards handle.
IF YOUR UNIT FAILS TO START:
See Troubleshooting on page 12.
: Briggs-Located on engine and must be controlled manually.
: Push primer per engine instructions (B&S only).
: Controlled by throttle lever on the engine. Under normal conditions, operate at minimum
: Move fuel valve to "ON" position (when provided on engine).
: Move throttle to fast/choke position. Located on handle.
HANDLING & TRANSPORTING:
This unit requires two people to lift it. Lift holding the lower handle and front wheels. Secure the
machine in place during transport. See page 3 for weight specifications
Never lift the machine while the engine is running.
STORAGE
Never store engine indoors or in enclosed poorly ventilated areas with fuel in tank, where fuel fumes may reach
an open flame, spark or pilot light, as on a furnace, water heater, clothes dryer or other gas appliance.
If engine is to be unused for 30 days or more, prepare as follows:
Remove all gasoline from carburetor and fuel tank to prevent gum deposits from forming on these parts and
causing possible malfunction of engine. Drain fuel outdoors, into an approved container, away from open flame. Be
sure engine is cool. Do not smoke. Run engine until fuel tank is empty and engine runs out of gasoline.
Part No 891058 Form No F072508B
9
Page 10
KVSP/TKVSP Owner’s Manual
OPERATION
VACUUMING OPERATION
VACUUM NOZZLE HEIGHT ADJUSTMENT
to reduce tension on the adjuster, and then pulling height adjust trigger on the handle (item 23) up at right rear of
machine. Then select the desired height that fits the task.
FOR MAXIMUM PICKUP: Adjust nozzle close to debris, but without blocking airflow into the nozzle. NOTE:
Never bury nozzle into debris.
CLEARING A CLOGGED NOZZLE & EXHAUST: Turn engine off and wait for impeller to stop completely
and disconnect spark plug wire. Wearing durable gloves, remove clog. Danger, the clog may contain sharp
materials. Reconnect spark plug wire.
: is raised and lowered by pushing slightly downward on handle
DEBRIS BAG
Debris bags are normal replaceable wear items.
Note: Frequently empty debris to prevent bag overloading with more weight than you can lift.
An optional felt bag is available for use where debris will be vacuumed in dusty conditions (see Optional Accessories
shown on page 1).
DO NOT place bag on or near hot surface, such as engine. Be sure engine has come to a complete stop before removing or
emptying bag.
This vacuum is designed for picking up trash, organic material and other similar debris (see Safety Warnings
page 4-5).
However, many vacuums are used where dust is mixed with trash. Your unit can intermittently vacuum in dusty areas.
Dust is the greatest cause of lost vacuum performance. However, following these rules will help maintain your
machine's ability to vacuum in dusty conditions:
• Run machine at idle to quarter throttle.
• The debris bag must be cleaned more frequently. A vacuum with a clean, pillow soft bag will have good pickup
performance. One with a dirty, tight bag will have poor pickup performance. If dirty, empty debris and vigorously shake
bag free of dust.
• Pressure-wash debris bag if normal cleaning does not fully clean bag. Bag should be thoroughly dry before use.
NOTE: Having one or more spare debris bags is a good way to reduce down time while dirty bags are being cleaned.
DO NOT leave debris in bag while in storage.
Part No 891058 Form No F072508B
10
Page 11
KVSP/TKVSP Owner’s Manual
COMPOST
Vacuumed leaves, grass and other organic material from your own yard can be emptied into a pile or composter to
provide enriched soil for later use as fertilizer in gardens and flower beds
NOTE: Allow green chips to dry before spreading around living plants.
MULCH
Wood chips made from branches in your own yard make excellent mulch. A thick blanket of wood chips around
plants and flowers to keeps weeds out and moisture in.
CHIPPER OPERATION (TKV only)
Your TKV chipper is designed to process tree branches and limbs up to 2"
(50.8mm) diameter.
Several small branches can be grouped together and fed together into the
chipper (see figure right).
When feeding forked branches, squeeze forks together and feed into chipper
entrance (DO NOT overload). If forks are too large, use a pair of loppers to trim
forks down to size. A lopper storage bracket is provided on every unit (loppers
are not included)
Clearing a clogged chipper (TKV only)
Under normal circumstances, allow time for machine to clear all wood
from chipper hopper before stopping engine. Otherwise, remaining
pieces of wood will jam inside of chipper when engine stops. (See
Tamper below).
Disconnect spark plug wire.
Remove debris bag quick disconnect from debris outlet on machine.
Wearing durable gloves, access impeller through debris outlet on fan housing
and rotate impeller counter clock wise to dislodge and remove jam and remove
debris from hopper with tongs or equivalent. Reconnect debris bag quick
disconnect to machine.
Reconnect spark plug wire.
TAMPER (TKV only)
Before turning machine off, use the Tamper to slowly push remaining pieces of
wood through the chipper. This can prevent any remaining wood from jamming
in the chipper when machine is turned off.
Do not leave tamper on the ground, store tamper in the chipper hopper.
Part No 891058 Form No F072508B
11
Page 12
KVSP/TKVSP Owner’s Manual
MAINTENANCE
ERIODIC MAINTENANCE
P
Periodic maintenance should be performed at the following intervals:
Maintenance Operation Every Use (daily) Every 5 hrs (daily) Every 25 Hours
Inspect for loose, worn or damaged parts.
Clean Debris bag
Check bag strap tightness
Engine (See Engine Manual)
Check for excessive vibration
IMPELLER REMOVAL
1. Wait for engine to cool and disconnect spark plug.
2. Drain fuel and oil from the engine.
3. Remove bag, quick release and upper handle. Do not kink, stretch, or break control cables, control
housings, or end fittings while removing handles.
4. Remove the transmission cover, idler pulley, transmission and the belt from the transmission.
5. Remove the transmission plate and the housing top plate by removing bolts around outside of housing.
6. Leaving engine fastened to top plate; turn it upside down so the impeller is on top.
7. Remove impeller bolt and lock washer.
8. Lift impeller upward. If impeller slides freely, proceed to (step 10).
9. If the impeller does not loosen, obtain a 3/4-16x3” (Billy Goat part #440192) or longer bolt. Thread bolt by
hand into nut until bolt rests against the shaft. Tighten the bolt slowly, which will pull the impeller away from the
shaft, remove impeller from shaft. Using a penetrating oil can help loosen a stuck impeller.
10. Using a new impeller bolt, lockwasher, and washer, reinstall new impeller in reverse order.
11. Tighten impeller bolt. Torque impeller bolt to 33-38 Ft. Lbs. (44-51 N.m) (see item 45 on page 15).
12. Reinstall engine onto housing in reverse order of removal make sure the belt is inside the two fingers on
the belt plate and that the belt is on the transmission pulley before securing the transmission.
13. Gas and oil.
14. Reconnect spark plug wire.
z
z
z
z
DRIVE CHAIN REPLACEMENT AND ALIGNMENT
1. Wait for engine to cool and disconnect spark plug.
2. To replace a chain, first prop up the rear of the machine with small blocks to get the rear wheels off of the
ground.
3. Remove the transmission cover, and the belt from the transmission.
4. Remove the bolts on both sides of the transmission holding the flange bearings; this should give enough
slack to slip the chain off.
4. Replace the old chain with a new one.
5. Once the chain is on, put the bolts back into the flange bearings and tighten.
6. Finally, make sure the wheels rotate freely. If not, loosen the bearings and shift them to get the chain
running straight up and down.
7. Reassemble the transmission components removed in steps 1-3 in reverse order.
Part No 891058 Form No F072508B
12
Page 13
KVSP/TKVSP Owner’s Manual
p
BELT TENSION ADJUSTMENT
DO NOT ADJUST WHILE THE MACHINE IS RUNNING!
1. Wait for engine to cool and disconnect spark plug.
2. Remove the transmission cover
3. Using two ½” wrenches loosen the two nuts on the cable that connects to the idler arm.
4. The setting of the tension on the belt is controlled by the distance on the threads of the cable. To loosen
tension, move the position towards the end of the threads and in the opposite direction to tighten.
5. Check the travel of the idler arm by engaging the bail, which the drive should start to engage when the bail
is 2 ½ inches away from the handle. The spring, at a relaxed state should be 1.5 inches long on the coil, and
when the bail is in contact with the handle it should be 1.75 inches long. If the belt is too tight it can cause
premature failure and if it is too loose it can come off of the pulley.
6. When satisfied with the position, place the transmission cover back into place and secure. Then run the
machine to make sure the transmission is engaging properly. If the drive will not engage or will not disengage
repeat the previous steps.
Spring length
1.5”- resting
1.75”- bail at
handle
BELT REPLACEMENT
1. Wait for engine to cool and disconnect spark plug.
2. Drain fuel and oil from the engine.
3. Remove bag, quick release and upper handle. Do not kink, stretch, or break control cables, control
housings, or end fittings while removing handles.
4. Remove the transmission cover, idler pulley, transmission and the belt from the transmission.
5. Remove the transmission plate and the housing top plate by removing bolts around outside of housing.
6. Leaving engine fastened to top plate, turn it upside down so the impeller is on top.
7. Remove impeller bolt and lock washer.
8. Lift impeller upward. If impeller slides freely, proceed to (step 10).
9. If the impeller does not loosen, obtain a 3/4-16x3” (Billy Goat part #440192) or longer bolt. Thread bolt by
hand into nut until bolt rests against the shaft. Tighten the bolt slowly, which will pull the impeller away from the
shaft, remove impeller from shaft. Using a penetrating oil can help loosen a stuck impeller.
10. Place the new belt on the shaft.
11. Using a new impeller bolt and lockwasher, reinstall new impeller in reverse order.
12. Tighten impeller bolt. Torque impeller bolt to 33-40 Ft. Lbs. (44-54 N.m) (see item 45 on page 15).
13. Make sure the belt is in the groove on the impeller and feed it through the hole in the top plate.
14. Reinstall engine onto housing in reverse order of removal make sure the belt is inside the two fingers on
the belt plate and that the belt is on the transmission pulley before securing the transmission.
15. Gas and oil.
16. Reconnect s
Part No 891058 Form No F072508B
ark plug wire.
13
Page 14
KVSP/TKVSP Owner’s Manual
f
CHIPPER BLADE REMOVAL AND SHARPENING (TKV ONLY)
Chipper blades are normal replaceable wear items.
DANGER Chipper blade is sharp. Replace any damaged blade.
Depending on the type and amount of wood being chipped, the chipper blade will eventually get dull, losing it’s
cutting ability. Evidence of a dull blade is a noticeably reduced chipping ability or a rough cut on end of branch.
Note: The chipper blade gap is factory set and should be checked each time impeller is removed from engine
crankshaft and reset if required. If reassembly requires a different quantity of shim washers, Billy Goat® shim
washer must be used.
1. Follow the steps 1-6 on the impeller removal instructions.
2. Using a 3/16" Allen wrench and 1/2" open end wrench, remove chipper blade from impeller.
3. Sharpen blade by lightly grinding the cutting edge of the blade at 40 degrees (see figure below). It is not
necessary to remove all nicks from the cutting edge. CAUTION: Be careful to avoid heat buildup in the blade
during sharpening. This will reduce it’s heat- treated hardness properties and will reduce blade life. Evidence o
too much heat build-up is a change of color along sharpened edge.
4. The same chipper blade can be sharpened several times. However, blade replacement is required when
blade no longer overhangs the chip relief hole in impeller back plate or if increased vibration occurs (see fig
below).
5. Chipper blade installation is in reverse order of removal.
Correct Incorrect
Blade
400
Edge of chip
relief hole
Part No 891058 Form No F072508B
14
Page 15
KVSP/TKVSP Owner’s Manual
Troubleshooting
Abnormal vibration. · Loose or out of balance impeller or
Will not vacuum or has poor
vacuum performance
Engine will not start. · Throttle in off position. Engine not in full
Engine is locked, will not pull
When servicing engine refer to specific manufacturers engine owner's manual. Engine warranty is covered by the specific engine manufacturer.
If your engine requires warranty or other repair work contact your local servicing engine dealer. When contacting a dealer for service it is a good
idea to have your engine model number available
for reference (See table page 3). If you cannot locate a servicing dealer in your area you can contact the manufacturers national service
organization.
To reach:
American Honda: 800-426-7701
Briggs & Stratton: 800-233-3723
over.
Nozzle scrapes ground in
lowest height setting.
No self-propelling · Drive bail not engaged · Engage the drive bail.
Self propelled drive will not
release
Noisy or broken chain · No chain lubrication. · Lubricate chain.
Unit does not free-wheel
backwards
Too much dust coming from
bag.
Problem Possible Cause Solution
loose engine
· dirty debris bag. Hose kit cap missing.
·Clogged nozzle or exhaust. Excessive
quantity of debris.
· Improper nozzle height
choke position. Out of gasoline. Bad or
old gasoline. Sparkplug wire
disconnected. Dirty air cleaner
· Debris locked in impeller. Engine
problem.
Nozzle height out of adjustment
· Drive belt worn or broken · Check the drive belt.
· Drive clutch cable out of adjustment or
broken.
· Drive chain off the sprocket. · Check the drive chain (see page 12).
· Improper drive clutch cable adjustment
or cable is kinked.
· Chain misalignment or tension. · Check the drive chain (see page 12).
· None · Push the unit slightly forward then the
· Vacuuming very dry, brittle or small
debris
· Check impeller and replace if required.
Check engine
· Clean debris bag. Shake bag clean or
wash. Check for hose kit cap. Unclog
nozzle or exhaust. Allow air to feed with
debris
· Adjust nozzle height so that it is closer
to the debris
· Check stop switches, throttle, choke
position and gasoline. Connect spark
plug wire. Clean or replace air filter. Or
contact a qualified service person.
· See page 5. Contact a engine service
dealer for engine problems
Adjust nozzle height (See Nozzle height
fine adjustment for hard surfaces on
page 5
· Check the drive clutch cable (see page
12).
· Check the drive clutch cable (see page
13).
unit will free-wheel
· Switch to felt bag (see page 1
accessories)
WARRANTY CLAIM PROCEDURE
Should a BILLY GOAT ® machine fail due to a defect in material and/or workmanship, the owner should make a warranty claim as follows:
• The machine must be taken to the dealer from whom it was purchased or to an authorized Servicing BILLY GOAT Dealer.
• The owner must present the remaining half of the Warranty Registration Card, or, if this is not available, the invoice or receipt.
• The Warranty Claim will be completed by the authorized BILLY GOAT Dealer and submitted to their respective BILLY GOAT
Distributor for their territory Attention: Service Manager. Any parts replaced under warranty must be tagged and retained for 90 days.
The model number and serial number of the unit must be stated in the Warranty Claim.
• The distributor service manager will sign off on the claim and submit it to BILLY GOAT for consideration.
• The Technical Service Department at BILLY GOAT will study the claim and may request parts to be returned for examination. BILLY
GOAT will notify their conclusions to the distributor service manager from whom the claim was received.
• The decision by the Technical Service Department at BILLY GOAT to approve or reject a Warranty Claim is final and binding.
For online product registration go to www.billygoat.com
Part No 891058 Form No F072508B
15
Page 16
KVSP/TKVSP Owner’s Manual
PARTS DRAWING KVSP/TKVSP
TKVSP
handle only
KVSP Top Plate
Assembly
Part No 891058 Form No F072508B
16
Page 17
* Denotes
O.
standard
hardware
item that
may be
purchased
locally.
KVSP/TKVSP Owner’s Manual
PARTS LIST KVSP/TKVSP
Part No 891058 Form No F072508B
ITEM
N
1 MAIN FRAME HOUSING KV 891100-S 1 891100-S 1 891100-S 1
2 NOZZLE ASSEMBLY TKV 891110-S 1 891110-S 1 891110-S 1
3 AXLE FRONT WA KV 891103 1 891103 1 891103 1
4 PLATE TOP WA KVSP 891101-S 1 891101-S 1 891107-S 1
5 IMPELLER SERRATED 14.25 WA KVSP 891104-S 1 891104-S 1 891109-S 1
6 DOOR EXHAUST ASSY RAW 890148-01 1 890148-01 1 890148-01 1
7 WASHER 1/2" SAE Z/P 8172011 4 8172011 4 8172011 4
8 WHEEL ASSY 12" X 2.5" TREAD 900509 4 900509 2 900509 2
9 ENGINE 6.5 HP HO NDA GSV190AN1L - - 8 40069 1 840069 1
10 LOWER HANDLE KV 891050 1 891050 1 891050 1
11 HANDLE UPPER KVSP 891054-S 1 891054-S 1 891054-S 1
12 QUICK DISCONNECT 890176 1 890176 1 890176 1
13 PIN CLEVIS 3/8" x 2.125" LONG 520120 4 520120 4 520120 4
14 RETAINER 360279 4 360279 4 360279 4
15 GRIP HANDLE 1"X 9.5" LG 430342 2 430342 2 430342 2
16 LABEL HOT ENGINE 400268 1 400268 1 400268 1
17 LABEL READ 890301 1 890301 1 890301 1
18 LABEL WARNING DANGE R 400424 2 400424 2 400424 2
19 LABEL DANGER FLYING DEBRIS 810736 1 810736 1 810736 1
20 LABEL EAR EYE BREATHING 890254 1 890254 1 890254 1
21 BAG DEBRIS NO ZIPPER KV 891132 1 891132 1 891132 1
22 CABLE THROTTLE ASSY 42" W/CHOKE 891036 1 8 91027 1 891027 1
23 CABLE HGT ADJ TRIGGER KV 891001 1 891001 1 891001 1
24 CABLE CLUTCH DRIVE ASSY 40" KVSP 891032 1 891032 1 891032 1
25 LABEL CLUTCH VQ 900328 1 900328 1 900328 1
26 BRACKET TRANS MOUNT WA KV 891106 1 891106 1 891106 1
27 ARM IDLER DRIVE WA KV 891105 1 891105 1 891105 1
28 TRANS SINGLE SPEED W/DIFF 891020 1 891020 1 891020 1
29 SPROCKET 8 TOOTH #43 O R #65 891022 2 891022 2 891022 2
30 CHAIN #43 X 58 PITCHES 891023 2 891023 2 891023 2
31 GUARD DRIVE KV 891004-S 1 891004-S 1 891004-S 1
32 BEARING 1/2" PRESSED STEEL HOUSING 891025 2 891025 2 891025 2
33 BRACKET TRANS FIX KV 891012 1 891012 1 891012 1
34 PLATE CHAIN REINFORCE KV 891014 2 891014 2 891014 2
35 PULLEY IDLER 2" OD X 3/8" ID 840087 1 840087 1 840087 1
36 SPRING TENSION 800242 1 800242 1 800242 1
37 BAIL CLUTCH WA KVSP 891102 1 891102 1 891102 1
38 BRACKET IDLER BELT FINGER KV 891028 1 891028 1 891028 1
39 LABEL DANGER GU ARD 900327 1 900327 1 900327 1
40 WHEE L ASSY SP 26T SPROCKET 890242 2 890242 2 890242 2
41 SPACER 1.50OD X .890ID X .5 THK - - 8 40083 1 840083 1
42 WASHER LOCK 3/8 ST MED 8177012 1 8177012 1 8177012 1
43 SQ KEY 2.125 X .187 9201087 1 9201087 1 9201087 1
44 SCREW MACHINE #10-16 X 1 1/2" HW F ZP 891042 1 891042 1 891042 1
SCREWCAP 3/8-24 x 3 1/2 GR. 8 W/PATCH
45
46 SCREW CAP 1/4 - 20 x 5/8 HWH 890 359 26 890359 26 890359 24
47 BOLT IDLER 3/8-16 X 1 1/2 800888 1 800888 1 800888 1
48 W ASHER 1/4" SAE ZP 8172007 17 8172007 17 8172007 21
49 W ASHER 5/16 FLATWASHER Z/P 8171003 19 8171003 19 8171003 19
50 SC REWCAP 5/16-18 X 1.75 ZP 8041031 8 8041031 8 8041031 8
51 NUT LOCK 5/16-18 8160002 8 8160002 8 8160002 8
52 N YLON INSERT LOCKNUT, 3/8-16 UNC 81 60003 2 8160003 2 8160003 2
53 SC REWCAP 1/4-20 X 3/4" 8041004 6 8041004 6 80410 04 4
54 N YLON INSERT LOCKNUT, 1/4-20 UNC 81 60001 15 81600 01 15 8160001 18
55 SC REWCAP #10-14 X 3/4" HW H ZP 891043 3 891043 3 891043 3
56 1/2-13 CAP NUT N P W/PATCH 890530 4 890 530 4 890530 4
57 SCREWCA P 1/4-20 x 1 3/4 HCS ZP 8041009 1 80 41009 1 80 41009 1
58 SC REWCAP 1/4-20x2.25x0.75-N 8041011 1 8041011 1 8041011 1
59 BELT 3L310 891026 1 891 026 1 891026 1
60 SCREW CAP 1/4" - 20 X1 1/2" HCS ZP - - - - 8041008 1
61 NO ZZLE TOP HALF KV 891002 1 891002 1 891 002 1
62 NOZZLE BOTTOM HALF KV 891003 1 891003 1 891003 1
63 PLUG HO USING KD LB 900146-01 1 900146-01 1 900146-01 1
64 SCREW PLASTIC 1/4-20 X 1 891039 8 891039 8 891039 8
65 W ASHER 1.5 OD X .453 ID X .25 THK 440153 1 440153 1 440153 1
66 SCREW SELF TAP 10-24 X 1/2 8123086 1 8123086 1 8123086 1
67 SPROC KET 65A26 26 TOOTH
68
WASHER LO CK 1/4" EXTERNAL TOOTH 8181007 5 8181007 5 81810 07 5
69
70 SC REW TA PTITE 3/8 X 1 1/2 900564 3 900564 3 900564 3
71 SCREW CAP #10-24 X 5/8" - - - - 80 59135 4
72 N YLON INSERT LO CKNUT 10-32 UNF ZINC - - - - 8164005 4
73 SC REW SO CKET HD 5/16-18 X 3/4 GR . 8 - - - - 890103 2
74 NUT KEPS 5/16-18 - - - - 890104 2
75 W ASHER SHIM 0.875 ID X 0.060 - - - - 891065 2
76 W ASHER SHIM 0.875 ID X 0.020 - - - - 891041 0-3
77 BLADE CHIPPER KD501 - - - - 890101 1
78 GUARD FLAPPER - - - - 890119 2
79 PLATE FLAPPER ENTRANC E - - - - 890127 2
80 BR ACKET LOPPER LOOP - - - - 890167 1
81 TAMPER CHIPPER - - - - 890229 1
82 LABEL DANGER CHIPPER - - - - 890152 1
83 CLIP 1/2" 350146 4 350 146 4 350146 4
84 WO ODRUFF K EY 1/8 X 1/2 510180 2 510180 2 510180 2
85 HAIR PIN CO TTER 1/4 900471 1 900471 1 900471 1
86 SPRING COMPRESSION KD HG T 900136 1 900136 1 900136 1
87 LABEL DECAL KV/TKV 891046 1 891046 1 891047 1
88 SC REW SM 1/4 X 3/4 DRILL PT 510208 4 510208 4 510 208 4
89 W ASHER 1/4" SAE BLACK OXIDE 510193 4 510193 4 510193 4
91 BELT FING ER GUIDE 891063 2 891063 2 891 063 2
92 CAR RIAGE BOLT 1/4"-20 X 3/4" 8024021 2 8024021 2 8024021 2
93 SCREW CAP 1/4-20 X 1" HCS ZP 8041006 6 8041006 6 8041006 6
94 KV REINFORC EMENT NO ZZLE BRACKET LFT 891062 1 891 062 1 891062 1
95 KV REINFOR CEMENT NO ZZLE BRACKET RT 891064 1 891064 1 891064 1
96
97 SPRING LEVER G Z 610429 1 610429 1 610429 1
98 TY W RAP 900407 3 900407 3 900407 3
Description
ENGINE 6 BRIGGSAND STRATTON 890622 1 - - - -
SCREW SELF TAP 1/4 x 0.75 900505 5 900505 5 900505 5
KV600SP
PART
440151 1 440151 1 440151 1
890238 1 890238 1 890238 1
17
QTY
KV650SPH
PART
QTY
TKV650SPH
PART
QTY
Page 18
KVSP/TKVSP Owner’s Manual
MAINTENANCE RECORD
Date Service Performed
Part No 891058 Form No F072508B
18
Page 19
KVSP/TKVSP Owner’s Manual
BRUSH CUTTER FORCE BLOWER AERATOR
If you liked this product please feel
free to view our full line of quality lawn
care, renovation, and debris removal
products at www.billygoat.com
DL VACUUM MULTI VACUUM POWER RAKE
Part No 891058 Form No F072508B
19
Page 20
KVSP/TKVSP Owner’s Manual
Part No 891058 Form No F072508B
20
Loading...