Page 1
1
Thank You for Selecting
SV50HR
Operator Owner's Manual
Quiet Vac
R
3
ENGIN E: H.P. 5.5 (4.1kW)
ENGINE: TYPE HONDA OHV
ENGINE: FUEL CAP. 1.2qt. (1. 1 L)
ENGIN E: OIL CAP. 0.63qt. (0.60L)
WE I GH T : UNI T 151# (68.5kg)
WE I GH T : S HIPP I NG 174# (78.9kg)
ENGINE WEIGHT: 36# (16.3kg)
UN IT LENGTH 62" (1.57m)
UN IT WIDTH 26.75" (0.68m)
UN IT HEIGH T 42" (1.07m)
SPECIFICATIONS
SV 50HR
ACCESSORIES
2
HOSE KITS
For vacuuming in hard to reach areas.
Heavy Duty Vacuum
Hose Kit P/N 900998.
NOZZLE WEAR GUARD
(STANDARD)
P/N 890413.
when used along curbs and hard
surfaces.
Extends nozzle life
P/N 890447 For use on
hard surface.
CASTER KIT
4"(102mm) x 7 ' (3.05m)
Hose Extension Kit
P/N 890045.
(Kit contains a connector
and a clamp, Hose is not
included)
BAG LINER OPTIONS
Fe lt Fi l ter P / N 89 0435 Litter L i n er P / N 8 90006 La wn Li n er P / N 8 90009
For use in all dusty c ondit ions . Can be
used wit h ot he r lin ers
PACKAGED SINGLY QTY 5 PER PA CKA GE QTY 5 PER PA CKA GE
Part No. 890049 Form No. F100202A
For us e on ha rd s urfac e where a variety of
debris is pres en t.
Page 1 of 8
Used to collect leaves, thatch & grass.
Page 2
5
IN THE INTEREST OF SAFETY
BEFORE STARTING ENGINE, READ AND UNDERSTAND THE “ENTIRE OPERATOR'S MANUAL &
ENGINE MANUAL.”
THIS SYMBOL MEANS WARNING OR CAUTION. DEATH, PERSONAL INJURY AND/OR PROPERTY
DAMAGE MAY OCCUR UNLESS INSTRUCTIONS ARE FOLLOWED CAREFULLY.
WARNING: The Engine Exhaust from this product contains chemicals known
to the State of California to cause cancer, birth defects or other reproductive harm.
WARNING: DO NOT
1. DO NOT run engine in an enclosed area.
Exhaust gases contain carbon monoxide, an
odorless and deadly poison.
2. DO NOT place hands or feet near moving
or rotating parts.
3. DO NOT store, spill or use gasoline near
an open flame, or devices such as a stove,
furnace, or water heater which use a pilot
light or devices which can create a spark.
4. DO NOT refuel indoors where area is not
well ventilated. Outdoor refueling is recommended.
5. DO NOT fill fuel tank while engine is
running. Allow engine to cool for 2 minutes
before refueling. Store fuel in approved
safety containers.
6. DO NOT remove fuel tank cap while
engine is running.
7. DO NOT operate engine when smell of
gasoline is present or other explosive
conditions exist.
8. DO NOT operate engine if gasoline is
spilled. Move machine away from the spill
and avoid creating any ignition until the
gasoline has evaporated.
9. DO NOT transport unit with fuel in tank.
10. DO NOT smoke when filling fuel tank.
11. DO NOT choke carburetor to stop
engine. Whenever possible, gradually
reduce engine speed before stopping.
13. DO NOT tamper with governor springs,
governor links or other parts which may
change the governed engine speed.
14. DO NOT tamper with the engine speed
selected by the engine manufacturer.
15. DO NOT check for spark with spark plug
or spark plug wire removed. Use an
approved tester.
16. DO NOT crank engine with spark plug
removed. If engine is flooded, place throttle
in “FAST” position and crank until engine
starts.
17. DO NOT strike flywheel with a hard
object or metal tool as this may cause
flywheel to shatter in operation. Use proper
tools to service engine.
18. DO NOT operate engine without a
muffler. Inspect periodically and replace, if
necessary. If engine is equipped with
muffler deflector, inspect periodically and
replace, if necessary, with correct deflector.
19. DO NOT operate engine with an
accumulation of grass, leaves, dirt or other
combustible material in the muffler area.
20. DO NOT use this engine on any forest
covered, brush covered, or grass covered
unimproved land unless a spark arrester is
installed on the muffler. The arrester must
be maintained in effective working order by
the operator. In the State of California the
above is required by law (Section 4442 of
the California Public Resources Code).
Other states may have similar laws. Federal
laws apply on federal lands.
21. DO NOT touch hot muffler, cylinder, or
fins because contact may cause burns.
22. DO NOT run engine without air cleaner
or air cleaner cover.
23. DO NOT operate during excessive
vibration!
24. DO NOT leave machine unattended
while in operation.
25. DO NOT park machine on a steep grade
or slope.
WARNING: DO
1. ALWAYS DO remove the wire from the
spark plug when servicing the engine or
equipment TO PREVENT ACCIDENTAL
STARTING.
2. DO keep cylinder fins and governor
parts free of grass and other debris
which can affect engine speed.
3. DO pull starter cord slowly until resistance is felt. Then pull cord rapidly to avoid
kickback and prevent hand or arm injury.
4. DO examine muffler periodically to be
sure it is functioning effectively. A worn or
leaking muffler should be repaired or
replaced as necessary.
5. DO use fresh gasoline. Stale fuel can
gum carburetor and cause leakage.
6. DO check fuel lines and fittings frequently
for cracks or leaks. Replace if necessary
7. Follow engine manufacturer operating
and maintenance instructions.
8. Inspect machine and work area before
starting unit.
12. DO NOT run engine at excessive
7
speeds. This may result in injury & /or
damage to unit.
6
SAFETY INSTRUCTIONS
GENERAL SAFETY
PARTS BAG
CONTROLS & LABELS
ASSEMBLY
OPERATION
PARTS DRAWING & LIST
MAINTENANCE
TROUBLESHOOTING
WARRANTY PROCEDURE
○○○○○○○○
○○○○○○○○
○○○○○○○○
○○
○○○○○
○○○
○○
○○○○○○
○○○
○○
Sound tests conducted were in accordance with 2000/14/EEC
and were performed on 2/13/2002 under the conditions listed:
NOTE: Sound power level listed is the highest value for any model in this manual. Please
refer to serial plate on the unit for the sound power level for your model.
2
3
3
3
4
5
6-7
8
8
8
109 dB
(SV50H MODEL)
Sound level of 97 dBA at operator position
BAROMETRIC PRESSURE:
Part No. 890049 Fo rm N o. F100 202A
SOUND
GENERAL CONDITION:
TEMPERATURE:
WIND SPEED:
WIND DIRECTION:
HUMIDITY:
Page 2 of 8
Sunny
48° F (8.9° C)
2 MPH (3.2 kmh)
South East
29 %
30.34" Hg (770mm Hg)
8
VIBRATION LEVELS 2.5g
Vibration levels at the operators handles were
measured in the vertical, lateral, and longitudinal
directions using calibrated vibration test equipment.
Tests were performed on 04/02/98 under the
conditions listed:
GENERAL CONDITION:
TEMPERATURE:
WIND DIRECTION:
BAROMETRIC PRESSURE:
VIBRATION
WIND SPEED:
HUMIDITY:
67° F (19.4° C)
5 MPH (8.0 kmh)
29.1" Hg (739mm Hg)
Sunny
East
41 %
Page 3
9
GENERAL SAFETY
For your safety and the safety of others, these directions should be followed:
Do not operate this machine without first reading
owner's manual and engine manufacturer's manual.
Use of Ear Protection is recommended while
operating this machine.
Use of Eye and Breathing protection is recom mended when using this machine, especially in dry
and dusty conditions. Debris bag directs dust toward
ground, away from the operator and the optional Felt
Filter reduces the amount of dust reintroduced into the
environment.
·DO NOT place hands or feet inside nozzle intake opening,
near debris outlet or near any moving parts.
·DO NOT start engine without debris bag connected firmly in
place to exhaust outlet.
·DO NOT start or operate machine with debris bag zipper
open.
11
12
Check
PACKING CHECKLIST
Check
Debris Bag
890351
LITERATURE ASSY P/N 890048
Owner's
Manual
890049
Check
Literature
Accesso-
ries 890380
These items should be included in your carton. If any
of these parts are missing, contact your dealer.
Check
Litter LIner
Check
Installation
instructions
·DO NOT operate during excessive vibration.
·DO NOT remove bag until engine has been turned off and has
come to a complete stop.
·DO NOT remove hose kit cap on nozzle until engine has been
turned off and has come to a complete stop.
·DO NOT operate machine with hose cap, bag or hose removed.
·DO NOT use this machine for vacuuming exclusively sand,
dust, fine dirt, rock, glass, string like material, grain, rags,
cans, metal, bark or water.
·DO NOT operate this machine on slopes greater than 20%.
·DO NOT pick up any hot or burning debris, or any toxic or
explosive material.
·DO NOT allow children to operate this equipment.
Literature Assy
890381
890007
Check
Lawn Liner
Installation
Instructions
890432
Check
Check
Honda Engine
Manual
Warranty
Card 400972
Check
EU Declaration
of Conformity &
EU Distributor
List 890378
13
CONTROLS
Throttle
Control
STOP
SLOW
FAST
Honda - Place
in fast position
to start.
14
INSTRUCTION LABELS
These labels should be included on your Vacuum.
If any of these labels are damaged, replace them
before putting this equipment into operation. Item
and part numbers are given to help in ordering
replacement labels..
WARNING
EXPLOSIVE FUEL
STOP ENGINE AND ALLOW TO
COOL BEFORE REFUELING.
Label Do Not Fill While
Engine Is Hot
Item 63 Part No.400268
DANGER
Label Danger Flying Material
Item 62 Part No.810736
Label Ear Eye Breathing
Item No. 86 Part No.
890254
400268
Label Danger Keep Hands
and Feet Away
Item 29 Part No.400424
810736
890254
Label Read Owner's
Manual Item 84
Part No.890301
15
ENGINE LABELS
Honda
When servicing engine refer to specific manufacturers engine owner's
manual. All engine warranty is covered by the specific engine
manufacturer. If your engine requires warranty or other repair work
contact your local servicing engine dealer. When contacting a dealer
for service it is a good idea to have your engine model number
available for reference(See table above). If you can not locate a
servicing dealer in your area you can contact the manufacturers
national service organization.
To reach:
American Honda:
Phone: 770-497-6000 Fax: 770-497-6011
Part No. 890049 Form No. F100202A
Page 3 of 8
Page 4
10
ASSEMBLY
Your Billy Goat is shipped from the factory in one carton, completely assembled except for the upper
handle and accessories. Included with machine are caster kit (890447), felt filter bag (1 each), lawn
liner (3 each), and litter liner (3 each).
Read all safety and operating instructions
before assembling or starting this unit.
1.
2.
1. REMOVE items 8 locknut & 74
screws from lower handle (item
27). Attach and securely tighten
upper handle item 6 to lower
handle as shown.
2. REMOVE deflector (item 83)
from box. Discard packing
material. Remove carriage
bolts (item 31) and nut (item 4)
from deflector. Install to bag
plate (item 13) as shown
reusing parts removed (nut
should be on side shown).
Failure to attach
deflector may result in
premature wear to bag.
5.
PUT OIL IN ENGINE
BEFORE STARTING
6.
7.
SEE ENGINE MANUFACTURER'S
MANUAL (some engine manufactures' have different oil checking
procedures)
3.
4.
3. UNFOLD the debris bag
(item 1) position bottom of bag
rod below the bag plate and
pull up and rotate the top of the
bag rod up and secure with the
latch.
6. CONNECT spark plug wire.
7. VERIFY fuel valve on.
4. ATTACH bag hanger strap to bag
supports (item 11), preassembled to
upper handle.
4a. Bag hanger straps are designed
for adjustment when more clearance
is required between bag and ground.
Typically the bottom loop of the strap
is used when operating on turf.
Part No. 890049 Fo rm N o. F100 202A
Page 4 of 8
Page 5
16
Operation
INTENDED USE: This machine is designed for vacuuming
leaves, grass clippings and other types of organic litter as
well as debris mixed with cans, bottles and small amounts of
sand; however, vacuuming cans, bottles and sand will affect
the longevity of your machine.
Like all mechanical tools, reasonable care must
be used when operating machine.
Do not operate if excessive vibration occurs. If excessive
vibration occurs, shut engine off immediately and check for
damaged or worn impeller, loose impeller bolt, loose impeller
key, loose engine or lodged foreign objects. Note: See parts list
for proper impeller bolt torque specifications. (See trouble
shooting section on page 7).
Inspect machine work area and machine before operating. Make sure that all operators of this equipment are
trained in general machine use and safety.
PUT OIL IN ENGINE BEFORE STARTING.
16.1
Engine must be level when checking and filling oil and
gasoline.
ENGINE SPEED: Controlled by throttle lever on the handle.
Under normal conditions, operate at minimum throttle to
accomplish your current cleaning task.
FUEL VALVE: Move fuel valve to "ON" position
CHOKE: Operated with throttle control (Honda).
NOTE: Outer bag and rod (items 1 and 3) MUST depress the
bag presence switch (item 17) for the unit to start. See fig.1
IF YOUR UNIT FAILS TO START:
See Troubleshooting on page 8.
16.2
STARTING
ENGINE: See engine manufacturer’s instructions
for type and amount of oil and gasoline used.
(Honda only).
Post to prime (Briggs & Stratton).
VACUUMING OPERATION
VACUUM NOZZLE HEIGHT ADJUSTMENT: The
vacuum nozzle is raised and lowered by pulling slightly
upward on handle and pulling height adjust T-Handle (item
23) at operators left hand. Lift handle up or down to desired
height, then release T-handle.
FOR MAXIMUM PICKUP: Adjust nozzle height as
close to debris as possible, but without blocking airflow into the
nozzle. NOTE: Never bury nozzle into debris.
CLEARING A CLOGGED NOZZLE
& EXHAUST: Turn engine off and wait for impeller
to stop completely and disconnect spark plug wire.
Wearing durable gloves, remove clog. Danger, the
clog may contain sharp materials. Reconnect spark
plug wire.
H
16.3
DEBRIS BAG
Debris bags are normal replaceable wear items.
Note: Frequently empty debris to prevent bag overloading with
more weight than you can lift.
Bag liners are included and available for use in various conditions
where debris will be vacuumed.
DO NOT place bag on or near hot surface, such as engine.
Be sure engine has come to a complete stop
(see Bag Liner Options shown on page 1).
before removing or emptying bag!!
This vacuum is designed for picking up trash, organic
material and other similar debris
Many vacuums are used where dust is mixed with trash. Your
unit can intermittently vacuum in dusty areas. However, following
these rules will help maintain your machine's ability to vacuum in
dusty conditions:
(see Safety Warnings page 2-3).
•Run machine at idle to quarter throttle.
•Machine or pressure-wash debris bag if normal cleaning does
not fully clean bag. Bag should be thoroughly dry before use.
Having one or more spare Felt Filter (890435) is a good way to reduce
int!
down time while dirty bags are being cleaned.
Do not store with debris in bag. Organic
debris generates heat during decomposi-
tion and could damage the bag or start a fire.
16.4
Using two people to lift machine is recommended. Lift holding the
handle and front of nozzle. Secure in place during transport.
16.5
areas with fuel in tank, where fuel fumes may reach an open
flame, spark or pilot light, as on a furnace, water heater, clothes
dryer or other gas appliance.
If engine is to be unused for 30 days or more, prepare as
follows:
gasoline from carburetor and fuel tank to prevent gum deposits
from forming on these parts and causing possible malfunction of
engine. Drain fuel outdoors, into an approved container, away
from open flame. Run engine until fuel tank is empty and
engine runs out of gasoline.
NOTE: Fuel stabilizer (such as Sta-Bil) is an acceptable
alternative in minimizing the formation of fuel gum deposits
during storage. Add stabilizer to gasoline in fuel tank or storage
container. Always follow mix ratio found on stabilizer container.
Run engine at least 10 min. after adding stabilizer to allow it to
reach the carburetor.
HANDLING & TRANSPORTING:
STORAGE
Never store engine indoors or in enclosed poorly ventilated
Be sure engine is cool. Do not smoke. Remove all
16.10
Vacuumed leaves, grass and other organic material from your
own yard can be emptied into a pile or composter to provide
enriched soil for later use as fertilizer in gardens and flower beds
Note: Allow green chips to dry before spreading around living
plants.
COMPOST
SPARK
PLUG
THROTTLE
STOP
BAG PRESENCE
SWITCH
fig 1.
Part No. 890049 Form No. F100202A
Page 5 of 8
Page 6
18
PARTS DRAWING
SV50HR
Part No. 890049 Fo rm N o. F100 202A
Page 6 of 8
Page 7
* Denotes standard hardware item that may be purchased locally.
19
Item PARTS SV50HR QTY
No. LIST Part No.
1 OUTER DEBRIS BAG 890351 1
2 THROTTLE CONTROL 850270 1
3 ROD B A G NO CHANNEL 8900 36 1
4 NUT LOCK (1/4 - 20 ) *8160001 17
5 SCREW CAP ( 1/4 - 20 x 1-1/2 HEX ) *8041008 2
6 HA NDLE UPPER W/GRIP 890439 1
7 AXLE HEIGHT ADJUST 890389 1
8 SCREW CAP 5/16 - 18 x 1- 3/4 *8041031 2
9 CLAMP CABLE 1" I.D. 900813 2
10 TY WRAP *900407 2
11 BAG BAG SUPPORT 900039 1
12 LATCH BAG 890356 1
13 PLATE BAG NO CHANNEL 890039 1
14 BRA CKET HA NDLE SV 890532 2
15 BOLT CA RR. 5/16 - 18 x 3/4 ZP 8024039 2
16 WASHER FLAT 1/2 SAE *8172011 4
17 SWITCH PLUNGER 890440 1
18 BRA CKET - LOWER HEIGHT ADJUSTMENT 890021 1
19 SCREW 3/8 X 1 1/2 TAPTITE 890408 4
20 SPRING-COMPRESSION 900136 1
21 TIRE - ONLY ( PER ASSY) 900507 1
22 PIN - HAIR COTTER 900471 1
23 CABLE HEIGHT A DJUSTMENT 890019 1
24 BOLT - CARRIAGE 5/16 - 18 x 4 1/2 *8024054 4
25 GRIP HA NDLE 4005 70 2
26 NUT LOCK 5/16 - 18 HEX *8160002 6
27 HANDLE LOWER 890346 1
28 PLATE HANDLE SUPPORT 900933 1
29 ENGINE PLATE MOUNT 890337 1
30 WASHER FLAT CUT 5/16 *8171003 2
31 SCREW CARRAIGE 1/4-20 x 3/4 *8024021 12
32 SCREW CAP 1/4 - 20 x 1/2 HWH 890359 6
33 STRAIN RELIEF HAY CO 1244 500282 1
34 WHEEL ASS’Y (incl. items 21) 900509 4
35 WASHER 0.75 “C” 900997 1 - 0
36 PLATE DEFLECTOR SV 890011 1
37 HEIGHT ADJUST ASSY ( incl. items 18,20,22,23,25) 890013 1
38 SEAL BAG 890018 2
39 1/2-13 CAP NUT NP W/PATCH 890530 4
40 SCREW CAP 1/4 - 20 x 1 - 1/4 *8041007 4
41 HARNESS ASSY 890442 1
42 SCREW SELF TAPPING 10 - 24 x 1/2 *8123086 1
43 NOZZLE MAINFRAME A SS’Y ( incl. one of items 29,44,42) 890391 1
44 PLUG HOUSING 900146 1
45 SCREW CAP 1/4-20x 1-3/4 *8041009 2
46 SCREW SM 1/4 x 3/4 TYPE A *812208 2 4
47 PLATE SKID ( incl. items 78) 890413 1
48 IMPELLER ASS’Y (incl. items 49, 50, 51) 890382 1
49 KEY 900162 2
50 WASHER LOCK 3/8 TWISTED TOOTH 400502 1
51 SCREW CAP 3/8 -24 x 1 (HARDENED)( TORQ.50 FT-LBS)(68N.m) 900154 1
52 HOUSING ASS’Y ( incl. items 29, 62, 84, 86) 890388 1
53 ENGINE HONDA 5.5 H.P. GXV160 KN12 900615 1
54 TERMINAL PIGGYBACK 3/16 890010 1
55 LABEL DO NOT FILL WHEN ENGINE IS HOT 400268 1
56 LABEL EAR EYE BREA THING 890254 1
57 LABEL DANGER FLYING DEBRIS 810736 1
58 LABEL READ OW NER'S MANUAL 890301 1
59 LABEL DANGER CUT FINGER 400424 2
60 PLATE UPPER HEIGHT ADJUST 890005 1
Part No. 890049 Form No. F100202A
Page 7 of 8
Page 8
17
MAINTENANCE
Use only a qualified mechanic for any
adjustments, disassembly or any kind
of repair .
WARNING: TO AVOID PERSONAL INJURY, ALWAYS TURN
MACHINE OFF, MAKE SURE ALL MOVING PARTS COME
TO A COMPLETE STOP.
DISCONNECT SPARK PLUG WIRE
BEFORE SERVICING UNIT.
ENGINE: See engine manufacturer
operator's instructions.
RECONNECT SPARK PLUG WIRE,
GUARDS, BAG, CAPS AND / OR
HOSE BEFORE STARTING ENGINE.
Maintenance Schedule
17.2
Maintenance Operation
Engine (See Engine Manual)
Check for excessive vibration
Clean Debris Bag
Inspect for loose parts
Inspect for worn or damaged parts
Follow these hourly
maintenance intervals.
Every
Use
Every 5 hrs
or (Daily)
17.1
IMPELLER REMOVAL
For damaged or imbalanced
impeller
1. Wait for engine to cool and disconnect spark plug.
2. Drain fuel and oil from the engine.
3. Remove engine, impeller and mounting plate by removing nuts
(item 26) around outside of housing.
4. Leaving engine fastened to plate, remove impeller bolt (item 50)
and lock washer and slide impeller off crankshaft ( A puller may be
required).
CAUTION: Do not drop impeller.
5. If impeller does not slide off crankshaft, place two crowbars
between impeller and housing on opposite sides. Pry impeller away
from engine until it loosens. Using a penetrating oil can help loosen
a stuck impeller.
6. If the impeller cannot be loosened, obtain a 1” (25.4mm) longer
bolt of the same diameter and thread type as the impeller bolt.
Invert engine and impeller and support engine above ground to
prevent recoil damage. Thread longer bolt by hand into the
crankshaft until bolt bottoms. Using a suitable gear or wheel puller
against the bolt head and the impeller back-plate (near the blades),
remove impeller from shaft.
7. To reinstall impeller, use a new impeller bolt and lockwasher
8. Tighten impeller bolt. Torque impeller bolt to 50 Ft. Lbs. (68 N.m).
9. Reinstall engine, impeller, and mounting plate onto housing in
reverse order of removal.
10. Before connecting spark plug wire, slowly pull engine starting
rope to insure that impeller rotates freely.
11. Reinstall spark plug wire.
20
TROUBLESHOOTING
Before Requesting Service Review These Suggestions
Proble m Possible Cause Solution
Will not vacuum or has poor vacuum performance. · Dirty or full debris bag or filter. · Clean debris bag and filter. Shake bag clean or
· Nozzle height set too high or too low. · Adjust nozzle height.
· Hose kit cap missing. · Check for hose kit cap.
· Clogged nozzle or exhaust. · Unclog nozzle or exhaust (see page 5)
· E xcessive quantity of debris. · Allow air to feed with debris.
Abnormal vibration. · Loose or out of balance impeller. · Check impeller and replace if required.
Engine will not start. · Throttle in off position. · Check throttle
22.1
Contact your nearest engine manufacturer's authorized
Engine Service and Warranty
servicing dealer.
21
Serial Plate
Record your machine model, serial number and
date-of-purchase and where purchased
1803 S.W. Jefferson
Lee's Summit,
MO 64062 / USA
R
Tel (816) 524-9666
Fax (816) 524-6983
Model Serial No.
109 dB
Purchase
Date
Unit(Weight) Engine Power
lbs. kg kW rpm
Purchased
from
Part No. 890049 Fo rm N o. F100 202A
· Loose engine. · Check Engine.
· E ngine not in full choke position. · Check throttle, choke position
· Out of gasoline or bad or old gasoline. · Check throttle, choke position and gasoline.
· Spark Plug w ire disconnected. · Connect spark plug wire.
· Gas Valve off. · Turn on gas valve.
· Dirty air cleaner. · Clean or replace air cleaner. Contact a qualified
· Safety Interlock disengaged on bag plate. · Bag not fully engaged or Rod in bag is bent.
Please fill in the WARRANTY CARD and send the upper part to Billy Goat.
22
The WARRANTY terms are stated on the lower part which remains with the
user. Whenever a Billy Goat Machine is faulty due to a defect in material
and / or workmanship, the owner should make a warranty claim as follows:
The Machine should be taken to the dealer from whom it was
purchased or to an authorized Billy Goat dealer.
The owner should present the remaining half of the Warranty
Registration Card, or, if this is not available, the invoice or receipt.
The Warranty Claim will be filled in by the authorized Billy Goat Dealer,
who will send it with the faulty part to Billy Goat headquarters.
The Quality / Service department at Billy Goat headquarters will study
the claim and parts and will notify their conclusions.
The decision by the Quality / Service department at Billy Goat
headquarters to approve or reject a Warranty claim is final and
-1
min
Note: To process a Warranty Claim, it is necessary to quote the Model
& Serial number who are printed on the Billy Goat Serial Plate.
Page 8 of 8
wash.
service person.
WARRANTY PROCEDURE
binding.
BILLY GOAT INDUSTRIES INC.
1803 S.W. JEFFERSON LEE'S SUMMIT, MO 64082 / USA
PHONE: 816-524-9666 FAX: 816-524-6983 www.billygoat.com
Loading...