
To secure blower for
transportation on trailer
floors.
Solid flat-free front tire.
Effective and Easy to use to
prevent blower from rolling.
For greater maneuverability
on hard surfaces.
FORCE PUSH BLOWER Owner’s Manual
IMPORTANT- READ CAREFULLY BEFORE USE AND KEEP FOR FUTURE REFERENCE
Patent #6,253,416 and other patents pending
FORCE BLOWER Owner's Manual
F902S, F902H, F1302H, F1402S, F1802V
Beginning Serial #: 110215001
Accessories
Original Instructions
Part No 440313 1 Form No F110215A

FORCE PUSH BLOWER Owner’s Manual
SPECIFICATIONS 3
INSTRUCTION LABELS 4
PACKING CHECKLIST 5
ASSEMBLY 6
OPERATION 7
MAINTENANCE AND TROUBLESHOOTING 8
MAINTENANCE RECORD 9
ILLUSTRATED PARTS AND PARTS LISTS 10-12
DECLARTAION OF CONFORMITY 13-15
CONTENTS
Part No 440313 Form No F110215A

FORCE PUSH BLOWER Owner’s Manual
In compliance with
2000/14/EEC
Standards
Vibration at Operator
Position
General Conditions: Sunny
Temperature: 40.4oF (4.7oC)
Wind Speed: 6.1 mph (9.9kph)
Wind Direction: Southwest
Humidity: 93.6%
Barometric Pressure: 30Hg (101.85kpa)
General Conditions: Sunny
Temperature: 57.2oF (14.3oC)
Wind Speed: 11.8 mph (19.1kph)
Wind Direction: South
Humidity: 46.4%
Barometric Pressure: 30.1Hg (101.96kpa)
SPECIFICATIONS
F902S F902H F1302H F1402S F1802V
SOUND
SOUND LEVEL 97 Db(a) at Operators Position
Sound tests were conducted in accordance with 2000/14/EC, as well as ISO 11094, and were performed on 12-12-2006 under
the conditions listed below.
Sound power level listed is the highest value for any model covered in this manual. Please refer to serial plate on the unit for
the sound power level for your model.
VIBRATION DATA
VIBRATION LEVEL 1.2g (11.9m/s2)
Vibration levels at the operator’s handles were measured in the vertical, lateral and longitudinal directions using calibrated
vibration test equipment. Tests were performed on 12-13-2006 under the conditions listed below.
Part No 440313 Form No F110215A

FORCE PUSH BLOWER Owner’s Manual
HONDA MOTOR CO. , LTD. MADE IN JAPAN
READ OWNER’S MANUAL BEFORE OPERATION.
LIRE LE MANUEL D UTILISATEURAVANT USAGE.
VOR INBETRIEBNAHME UNBEDINGHT BEDIENUNGSANLEITUNG DURCHLESEN.
NO UTILIZAR SINANTES NO HABER LEIDO EL MANUAL
WHEN OIL LEVEL LOW,
ENGINE STOPS IMMEDIATELY.
OIL ALERT
BRIGGS AND STRATTON VANGUARD
LABEL SPARK ARRESTOR
P/N 100252
INSTRUCTION LABELS
The labels shown below were installed on your BILLY GOAT® FORCE Blower. If any labels are damaged or missing, replace
them before operating this equipment. For your convenience in ordering replacement labels, part numbers are included in the
Illustrated Parts List. The correct position for each label may be determined by referring to the Figure and Item numbers shown.
LABEL READ OWNERS MANUAL LABEL SAFETY PROTECT DANGER FLYING DEBRIS
ITEM #44 P/N 890301 ITEM# 45 P/N 100346 ITEM # 46 P/N 810736
LABEL EXPLOSIVE FUEL LABEL THROTTLE CONTROL
ITEM # 43 P/N 100261 ITEM # 42 P/N 810656
ENGINE LABELS
Part No 440313 Form No F110215A

FORCE PUSH BLOWER Owner’s Manual
READ all safety instructions before assembling unit.
TAKE CAUTION when removing the unit from the box the Handle Assembly is attached to the
unit by cables.
Front Air Diverter
(For F902S, F902H, F1302H, F1402S
models only)
Item#38
F9 MODEL P/N-440045-4
F13/F14 MODEL P/N-440045-5
Handle Upper Assembly
Item #30 P/N-440035
Parts Bag & Literature Assy
P/N-440266
PARTS BAG & LITERATURE ASSY
Warranty card P/N- 400972, Owner’s Manual P/N-440313, General Safety and Warnings Manual P/N-100294, Declaration of
Conformity P/N-440022, Handle Hardware-Items #10, #11, #74, #71 and #36
PACKING CHECKLIST
These items should be included in your carton. If any of these parts are missing, contact your dealer. Your BILLY GOAT®
FORCE Blower was shipped in one carton, completely assembled except for the Upper Handle Assembly and Front Diverter.
Mounting hardware for the Upper Handle Assembly can be found in the parts bag.
PUT OIL IN ENGINE BEFORE STARTING
Part No 440313 Form No F110215A