Billy Goat 350395, 350397 User Manual
N
POWER RAKE SEEDER BOX KIT-350395 AND 350397
PURPOSE: To overseed an existing lawn or start a new lawn.
Tools Required: 3/16" allen wrench, 7/16”, 1/2", 5/8", 3/4", 9/16”, 5/16”, 3/8” wrench, Wood blocks or suitable support for
machine.
"
"
INSTALLATION
Seeder Box Installation:
1. Disconnect spark plug wire.
2. Support Power Rake on blocks to lift left front wheel off ground.
3. Remove 4 screws from front of machine.
4. Remove left front wheel.
5. Install seeder box to front of machine with four 5/16” x 3/4 cap screws,
4 flat washers, and 4 lock washers. Do not tighten at this time (see figure
1).
Wheel:
1. Slide the pulley on until it rests firmly against the hub.
2. Tighten two setscrews.
3. Be sure 3 washers (item 31) are on the axle, slip the belt (item 24) in
the groove on the pulley and slide wheel on the axle.
4. Secure with lock nut (item 35).
NOTE: Replace thick locknut with the thin nut provided in parts bag.
ew units are provided with thin nuts.
Belt alignment:
1. Attach the belt onto the seeder box pulley by turning the wheel and
slowly feeding the belt onto the seeder box pulley.
2. Rotate wheel to insure belt turns freely
3. If the belt seems to be too tight, bump seeder box upward to loosen
belt.
4. Check the pulley alignment then tighten 4 capscrews inside seeder
box.
5.Repeat step 3 to 5 if necessary
6. Remove blocks from under machine & push machine to test
mechanism.
Seeder meter control box installation:
1. Attach the Seed drop control box (Item 2) to the upper handle with the
hardware from the parts bag (Items 17, 28, 35, 36, 39, 40) using a 7/16”
and a 9/16” wrench. Then attach the cable to the bail with hardware items
42 and 43 using 5/16” and a 3/8” wrenches. Secure the cable with a tywrap (item 44) to the upper handle.
2. Reconnect spark plug wire.
Fig. 2
Fig. 3
Fig. 4
Fig. 1
Part No 350398 - 1 - Form No F102207B
POWER RAKE SEEDER BOX KIT-350395 AND 350397
PARTS LIST
ITEM NO. PART NO. DESCRIPTION QTY
1 350366 BOX AND LID ASSEMBLY
2 350390 BRACKET CABLE MOUNTING 1
3 350385 CABLE SEED METERING ASSY 1
4 350320 SHAFT PLASTIC DROP SEEDER 1
5 350271 PLATE DOOR DROP SEEDER 1
6 350272 PLATE DOOR DROP SEEDER END 1
7 350387 PLATE DOOR DROP SEEDER END ARM 1
9 350370 PULLEY 3V GROOVE 0.625" BORE 1
10 8172009 WASHER #10 3/8 SAE 1
11 900321 BEARING CLIP 1.375 OD 4
12 890108 KNOB WING 5/16-18 1
13 400217 SPRING TENSION 2
14 8024040 BOLT CARRIAGE 5/16 - 18 X 1 1
15 8024021 BOLT CARRIAGE 1/4-20 X 3/4" 1
16 8123087 SCREW SELF TAP #10-24 X 3/8" HMS ZP 4
18 350389 BRACKET CABLE SEEDER BOX 1
19 8160002 NUT LOCK 5/16 1
21 350369 PULLEY 3V GROOVE 1.530" BORE 1
22 350280 WASHER 0.906 O.D. X 0.656 I.D. X 0.062 7-8
23 8041026 SCREWCAP 5/16-18 x 3/4 4
24 350372 BELT O-RING 5/16 X 15 9/16" 1
25 8197031 PIN COTTER 1/8" X 1" 1
26 9195106 ROLL PIN 1/8 - 1 1/4 1
27 8172020 WASHER 5/16 FENDER 4
29 350392 LABEL SEED METERING 1
30 350386 LABEL DROP SEEDER BOX 1
33 890456 LABEL HOSE PLUG KD/SV 1
34 350313 LABEL PRODUCT DECAL OS 1
37 440124 PIN CLEVIS .25 X.50 1
38 440193 PIN CLIP HITCH .051 X 3/4" 1
41 350390 BRACKET MOUNTING METERING SEED 1
Part No 350398 - 2 - Form No F102207B
PARTS BAG SEEDER BOX KIT 350396
1
17 8160001 NUT LOCK 1/4 1
20 8177011 WASHER LOCK 5/16 4
23 8041026 SCREWCAP 5/16-18 x 3/4 4
27 8172020 WASHER 5/16 FENDER 4
28 8172007 WASHER 1/4 SAE 1
31 8171006 WASHER 1/2 FC 3
32 8161044 NUT LOCK 1/2" THIN HGT 1
35 8024061 CARRIAGE BOLT 3/8-16 X 1 3/4" 1
36 8024025 CARRIAGE BOLT 1/4-20 X 1 3/4" 1
39 8160003 NUT LOCK 3/8-16 HEX 1
40 8171004 WASHER 3/8 FC 2
42 8059135 SCREW MACHINE #10-24 X 5/8 1
43 8164005 NUT LOCK LT #10-24 HEX 1
44 900407 TY WRAP 1
- 350398 LIT SEEDER BOX 1
Loading...