Billionton Systems MDCBTASC32 User Manual
MDCBTASC32
1.0
User’s Guide &
Manual
Index
Introduction 1
Features 1
Driver support 2
Driver installation 3
Windows 98 installation 3
Windows ME installation 8
Windows 2000 installation 12
Windows XP installation 18
Installing Bluetooth Software for Windows
20
1
1. Introduction:
The MDCBTAXX32 is designed to provide Modem and Bluetooth functions on a MDC
form Factor card. The Bluetooth function is based on CSR BlueCore03-ROM Single Chip,
which implements the full speed class 2 Bluetooth operations with full 7 slave Pico-net
support. The Bluetooth function of MDCBTAXX32 to host system is USB compliant with
USB V1.1 standard interface. The AZALIA mobile daughter card (MDC) specification
provides a mobile form-factor module and interface for audio/modem codec solutions
based upon the AZALIA Specification, revision 0.7. The MDC specification is open to the
industry to facilitate IHV validation on AZALIA based code.
2. Features:
Data Modem
V.92 / 56 Kbps (K56Flex and V.90)
V.34 (4.8 Kbps to 33.6 Kbps)
V.32 bis (4.8 Kbps to 14.4 Kbps)
V.22 bis (50 bps to 2.4 Kbps)
V21, Bell 103 / Bell 212
V.42 bis/MNP 5 data compression
V.42/MNP 2-4 error correction
Virtual Com port with a throughput of up to 460.8 Kbps
Hayes AT Command set
TIES escape code
Fax Modem Standard
Send and receive rates up to 14.4 kbps, V.17, V.29, V.27ter
ITU-T V.17, V.29, V.27ter, V.21 Ch2 and TIA/EIA 578 Class1 FAX
Bluetooth
CSR BC03 ROM / V1.2 Single chip Bluetooth System
Full speed USB interface support OHCI , UHCI compliant USB V1.1
Full embedded to RFCOMM
Bluetooth specification V1.2
USB specification V1.1
Support BT_ON control Bluetooth ON / OFF feature
Faster Connection
Adaptive Frequency Hopping (AFH)
1
Telephony Services
Country Select function
TAM
System Requirements
Pentium based (233 MHz and above)
Windows 98SE,Windows ME, Windows 2000 and Windows XP
MDC 1.0 / 30 pin Slot
8 Mbytes RAM (Drivers occupy ~ 1MB)
Bus Interface
Modem :Compliant to Intel Mobile Audio/Modem Daughter Card Specification 1.0
Bluetooth : USB 1.1 Compliant
Hardware
MDC Modem support Secondary Operating Modes
Bluetooth V1.2 and USB specification V1.1
Power Management
Supports ACPI Power Management and Modem wake-up on Ring.
3. Driver support:
MDC Modem : Windows 98SE, Windows 2000, Windows ME and Windows XP
Bluetooth : Windows 98SE, Windows 2000, Windows ME and Windows XP
2
4. Driver installation:
Before install this modem driver please make sure your PC or Notebook soundcard
driver is ready.
-Windows 98 installation:
Insert the modem card into your PC or Notebook MDC slot and then power on.
1. After start, please check device manager from control panel, you will see an
exclamation mark on PCI Card this device, please select this device and then click
"Properties".
2. Select "Reinstall Driver".
3
3. System will popup "Update Device Driver Wizard" window, and then click the "Next"
Button.
4. Select "Display a list of all the drivers…" and then click the "Next" Button .
4
5. Insert the driver disk and select the driver location, then click the "Next" Button.
6. Windows 98 will search and recognize the driver of the Device. Click the "Next" Button.
5
7. Windows will automatically copy the driver files and related files into your system. After
copying the driver files, click the "Finish" Button.
8. The modem will be detected, repeat steps from 4th to 6th and then click the "Next"
Button.
6
9. Click on the "Finish" Button to complete the installation.
7
-Windows ME installation:
Insert the device into your PC or Notebook MDC slot and power on.
1. After start, please check device manager from control panel, you will see an
exclamation mark on PCI Card this device, please select this device and click
"Properties".
2. Select "Reinstall Driver".
8
3. System will popup "Update Device Driver Wizard" window, select "Specify the
location of the drivers" and also select "Specify the location", then click "Next".
4. Select "Specify the location of the driver. (Advanced)" Insert the driver CD or
diskette, then select the driver location by keying the driver path.
9
5. Windows ME will automatically copies the driver files and related files into the system.
8. The modem will be detected, repeat steps from 4th to 6th and then click the "Next"
Button.
10
Loading...