Billion Electric Company 7300VP User Manual

BiPAC 7300VP/7300VGP

VoIP/(802.1 1g) ADSL2+ Router

User’s Manual

Chapter 1................................................................................................................... 2

1.1 Introducing the BiPAC 7300VGP series.............................................. 2

1.2 Features................................................................................................. 4

1.3 Applications of the BiPAC 7300VG P series........................................ 8

Chapter 2................................................................................................................... 9

2.1 Important Notes.................................................................................. 10

2.2 Package Contents...............................................................................10

2.3 The Front LEDs................................................................................... 11

2.4 The Rear Ports.................................................................................... 12

2.5 Cabling ................................................................................................ 14

Chapter 3................................................................................................................. 15

3.1 Before Configuration.......................................................................... 15

3.2 Factory Default Settings .................................................................... 21

3.3 LAN and WAN Port Addresses..........................................................21

3.4 Information from your ISP ................................................................. 22

3.5 Configuring with your (802.11g) ADSL2+ Router............................. 23

Chapter 4................................................................................................................. 26

4.1 Status...................................................................................................27

4.1.1 ARP T able......................................................................................... 30

4.1.2 Wireless Association ...................................................................... 31

4.1.3 Routing Table................................................................................... 32

4.1.4 DHCP Table ...................................................................................... 33

4.1.5 System Log...................................................................................... 34

4.1.6 Security Log.....................................................................................35

4.1.7 VoIP Log........................................................................................... 36

4.2 Quick Start .......................................................................................... 37

4.3 Configuration...................................................................................... 40

4.3.1 LAN (Local Area Network) .............................................................. 41

4.3.2 WAN (Wide Area Network) .............................................................. 48

4.3.3 System.............................................................................................. 55

4.3.4 Firewall.............................................................................................60

4.3.5 QoS (Quality of Service).................................................................. 69

4.3.6 Virtual Server................................................................................... 81

4.3.7 Advanced ......................................................................................... 85

4.3.8 VoIP.................................................................................................101

4.4 Save Configuration to Flash.............................................................111

4.5 Restart............................................................................................... 112

Chapter 5............................................................................................................... 113

5.1 How to obtain a personal phone number?..................................... 113

5.2 BiPAC 7300VGP VoIP Configuration............................................... 117

5.2.1 SIP Settings.................................................................................... 118

5.2.2 LINE Settings................................................................................. 119

5.3 How to make a call from FXS to FXO.............................................. 120

5.4 How to receiving an incoming call from FXO port......................... 121

5.5 General Tone Table........................................................................... 122

Chapter 6............................................................................................................... 124

Chapter 1

Introduction

1.1 Introducing the BiPAC 7300VGP series

Thank you for purchasing the BiPAC 7300VGP series ADSL2+ Router by Billion. Your new router is an all-in-one unit that combines an ADSL modem, ADSL2/2+ router and Ethernet network switch to provide everything you need to get the machines on your network connected to the Internet over an ADSL broadband connection.

The BiPAC 7300VGP series router complies with ADSL2+ standards for deployment worldwide and supports downstream rates of up to 24 Mbps and upstream rates of up to 1 Mbps. Designed for small office, home office and residential users, the router enables even faster Internet connections. You can enjoy ADSL services and broadband multimedia applications such as interactive gaming, video streaming and real-time audio much easier and faster than ever before.

The BiPAC 7300VGP series supports PPPoA (RFC 2364 – PPP (Point-to-Point Protocol) over ATM Adaptation Layer 5), RFC 1483 encapsulation over ATM (bridged or routed), PPP over Ethernet (RFC 2516), and IPoA (RFC1577) to establish a connection with your ISP. Your new router also supports VC-based and LLC-based multiplexing.

The perfect solution for connecting a small group of PCs to a high-speed broadband Internet connection, the BiPAC 7300VGP series allows multiple users to have high-speed Internet access simultaneously.

Your new router also serves as an Internet firewall, protecting your network from access by outside users. Not only does it provide a natural firewall function with Network Address Translation (NAT), it also provides rich firewall features to secure your network. All incoming data packets are monitored and filtered. You can also configure your new router to block internal users from accessing the Internet.

The BiPAC 7300VGP series provides two levels of security support. First, it masks LAN IP

addresses making them invisible to outside users on the Internet, so it is much more difficult for a hacker to target a machine on your network. Second, it can block and redirect certain ports to limit the services that outside users can access. To ensure that games and other Internet applications run properly, you can open specific ports for outside users to access internal services on your network.

The Integrated DHCP (Dynamic Host Control Protocol) client and server services allow multiple users to get IP addresses automatically when the router boots up. Simply set local machines as a DHCP client to accept a dynamically assigned IP address from the DHCP server and reboot. Each time a local machine is powered up; the router recognizes it and assigns an IP address to instantly connect it to the

LAN.

For advanced users, Virtual Service (port forwarding) functions allow the product to provide limited visibility to local machines with specific services for outside users. You can set an ISP (Internet Service Provider) provided IP address on the BiPAC 7300VGP series and then you can reroute specific services to individual computers on your local network. For instance, a dedicated web server can be connected to the Internet via the router and then incoming requests for web pages that are received by the router can be rerouted to your dedicated local web server, even though the server now has a different IP address. Virtual Server can also be used to re-task services to multiple servers. For instance, you can set the router to allow separated FTP, Web, and Multiplayer game servers to share the same Internet-visible IP address while still protecting the servers and LAN users from hackers.

BiPAC 7300VGP serves as a Public Switched Telephone Network (PSTN) handset-to-Ethernet adaptor that enables traditional telephone devices to operate as Internet Protocol (IP) devices. It is the interface between the PSTN world and the IP world acting as a residential gateway, eventually providing Internet Telephony capability. Cost savings and ease of developing and integrating new services motivate most of the interest in Internet telephony. Internet telephony integrates a variety of services provided by the current Internet and the PSTN infrastructure.

BiPAC 7300VGP extracts the maximum benefit from Voice over IP (VoIP) technology. It interfaces analog telephones with IP-based telephony networks. The integration of VoIP technology and ADSL Modem/Router is undoubtedly the most economic and practical solution to modern society.

1.2 Features

Express Internet Access – ADSL2/2+ capable

The BiPAC 7300VGP series complies with ADSL worldwide standards. Supporting downstream rates of 8Mbps with ADSL, the router is capable of up to 12/24 Mbps with ADSL2/2+, and upstream rates of up to 1 Mbps. Users enjoy not only high-speed ADSL services but also broadband multimedia applications such as interactive gaming, video streaming and real-time audio which are easier and faster than ever. The router is compliant with Multi-Mode standard (ANSI T1.413, Issue 2; G.dmt (ITU G.992.1); G.hs (ITU G994.1); G.dmt.bis (ITU G.992.3); and G.dmt.bisplus (ITU G.992.5)

Voice over IP compliance with SIP standard The router supports cost-effective, toll-quality voice calls over the Internet. It complies with the most popular industrial standard, SIP protocol, to ensure the interoperability with SIP devices and major VoIP Gateways. The VoIP ADSL router supports call waiting, silence suppression, voice activity detection (VAD), comfort noise generation (CNG), line echo cancellation, caller ID (Bell 202, V3) and so on.

802.11g Wireless AP with WPA Support (7300VGP only)

With integrated 802.11g Wireless Access Point in the router, the device offers a quick and easy access among wired network, wireless network and broadband connection (ADSL) with single device simplicity, and as a result, mobility to the users. In addition to 54 Mbps

802.11g data rate, it also interoperates backward with existing 802.11b equipment. The Wireless Protected Access (WPA) and Wireless Encryption Protocol (WEP) supported features enhance the security level of data protection and access control via Wireless LAN.

Fast Ethernet Switch A 4-port 10/100Mbps fast Ethernet switch is built-in with automatic switching between MDI

and MDI-X for 10Base-T and 100Base-TX ports, with auto dection allowing you to use either straight or cross-over Ethernet cables.

Multi-Protocol to Establish a Connection The router supports PPPoA (RFC 2364 - PPP over ATM Adaptation Layer 5), RFC 1483 encapsulation over ATM (bridged or routed), PPP over Ethernet (RFC 2516) and IPoA

(RFC1577) to establish a connection with an ISP. The router also supports VC-based and LLC-based multiplexing.

Quick Installation Wizard A web-based GUI and quick installation wizard help you easily install the BiPAC 7300VGP series. Enter your ISP’s information and begin browsing the Internet immediately.

Universal Plug and Play (UPnP) and UPnP NAT Traversal This protocol is used to enable simple and robust connectivity among stand-alone devices and PCs from many different vendors, and it makes setting up a network simple and affordable. UPnP architecture leverages TCP/IP and the Web to enable proximity networking in addition to control and data transfer among networked devices. With this feature enabled, you can seamlessly connect to Net Meeting or MSN Messenger.

Network Address Translation Network Address Translation (NAT) allows multiple users to access outside resources such as the Internet simultaneously with one IP address/one Internet access account. Many application layer gateways (ALG) are supported such as web browser, ICQ, FTP, Telnet, E-mail, News, Net2phone, Ping, NetMeeting, IP phone and others.

Firewall NAT technology supports simple firewalls and provides options for blocking access from the Internet, like Telnet, FTP, TFTP, WEB, SNMP and IGMP.

Domain Name System Relay Domain Name System (DNS) relay provides an easy way to map a domain name with a user-friendly name such as www.billion.com with an IP address. When a local machine sets its DNS server to the router’s IP address, every DNS conversion request packet from the PC to this router is forwarded to the real DNS on the outside network.

Dynamic Domain Name System (DDNS) The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname. This dynamic IP address is the WAN IP address. To use the service, you must first apply for an account from a DDNS service such as

http://www.dyndns.org/.

PPP over Ethernet (PPPoE)

The BiPAC 7300VGP series provides an embedded PPPoE client function to establish a connection. You get greater access speed without changing the operation concept, while sharing the same ISP account and paying for one access account. No PPPoE client software is required for the local computer. Automatic Reconnect and Disconnect Timeout (Idle Timer) functions are also provided.

Quality of Service (QoS)

QoS gives you full control over which types of outgoing data traffic should be given priority by the router, ensuring important data like gaming packets, customer information, or management information move through the router ay lightning speed, even under heavy load. The QoS features are configurable by source IP address, destination IP address, protocol, and port. You can throttle the speed at which different types of outgoing data pass through the router, to ensure P2P users don’t saturate upload bandwidth, or office browsing doesn’t bring client web serving to a halt. In addition, or alternatively, you can simply change the priority of different types of upload data and let the router sort out the actual speeds.

Virtual Server:

You can specify which services are visible to outside users. The router detects an incoming service request and forwards it to the specific local computer for handling. For example, you can assign a PC in a LAN to act as a Web server inside and expose it to the outside network. Outside users can browse inside the web server directly while it is protected by NAT. A DMZ host setting is also provided for local computers exposed to the outside Internet network.

Dynamic Host Configuration Protocol (DHCP) Client and Server On a WAN site, the DHCP client obtains an IP address from the Internet Service Provider (ISP) automatically. On a LAN site, the DHCP server allocates a range of client IP addresses, including subnet masks and DNS IP addresses and distributes them to local computers. This provides an easy way to manage the local IP network.

Rich Packet Filtering

This feature filters the packet based on IP addresses as well as Port numbers. Filtering packets to and from the Internet provides a higher level of security control.

Web-based GUI

A web-based GUI offers easy configuration and management. User-friendly and with on-line help, it also supports remote management capability for remote users to configure and manage this product.

Firmware Upgradeable You can upgrade the router with the latest firmware through its web-based GUI.

1.3 Applications of the BiPAC 7300VGP series

Chapter 2

Product Overview

Standards-Based Technology

The BiPAC 7300VGP Wireless Router utilizes the 802.11g standard. The IEEE 802.11g standard is an extension of the 802.11b standard. It increases the data rate up to 54Mbps* within the 2.4GHz band, utilizing OFDM technology. This means that in most environments, within the specified range of this device, you will be able to transfer large files quickly or even watch a movie in MPEG format over your network without noticeable delays. This technology works by transmitting high-speed digital data over a radio wave utilizing OFDM (Orthogonal Frequency Division Multiplexing) technology. OFDM works by splitting the radio signal into multiple smaller sub-signals that are then transmitted simultaneously at different frequencies to the receiver. OFDM reduces the amount of crosstalk (interference) in signal transmissions. The BIPAC 7300G is backwards compatible with 802.11b devices. This means that if you have an existing 802.11b network, the devices in that network will be compatible with

802.11g devices at speeds of up to 11Mbps in the 2.4GHz range.

Installation Considerations

The BiPAC 7300VGP Wireless Router lets you access your network, using a wireless connection, from virtually anywhere within its operating range. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass

Keep the number of walls and ceilings between the BiPAC 7300VGP and other network devices to a minimum - each wall or ceiling can reduce your BiPAC 7300VGP wireless product’s range from 3-90 feet (1-30 meters.) Position your devices so that the number of walls or ceilings is minimized.Keep the number of walls and ceilings between the BiPAC 7300VGP and other network devices to a minimum - each wall or ceiling can reduce your BiPAC 7300VGP wireless product’s range from 3-90 feet (1-30 meters.) Position your devices so that the number of walls or ceilings is minimized.Be aware of the direct line between network devices. Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better reception. Building Materials can impede the wireless signal - a solid metal door or aluminum studs may have a negative

effect on range. Try to position wireless devices and computers with wireless adapters so that the signal passes through drywall or open doorways and not other materials.4 Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate extreme RF noise.

2.1 Important Notes

Warning

 Do not use the BiPAC 7300VGP series in high humidity or high

temperatures.

 Do not use the same power source for the BiPAC 7300VGP

series as other equipment.

 Do not open or repair the case yourself. If the BiPAC 7300

VGP series is too hot, turn off the power immediately and have it repaired at a qualified service center.

 Avoid using this product and all accessories outdoors.

 Place the BiPAC 7300VGP series on a stable surface.  Only use the power adapter that comes with the package. Using

a different voltage rating power adaptor may damage the router.

2.2 Package Contents

BiPAC 7300VGP Series VoIP ADSL2+ Router

CD-ROM containing the online manual

RJ-11 ADSL/telephone Cable (1.8M)

Ethernet (CAT-5 LAN) Cable (2M Straight)

AC-DC power adapter (12V DC, 1.2A)

Quick Start Guide (130*185mm)

2.3 The Front LEDs

LED Description

1 PWR： Lights when the power is ON. 2 SYS： Lights when the system is ready.

Steady glow when connected to an Ethernet device. Glows green for 100Mbps; Orange for 10Mbps. Blinking light when data is Transmitted / Received.

Lit green when the wireless connection is established. Flashes when sending/receiving data.

3-6

LAN Port 1-4：

WLAN： (7300VGP

only)

8-9 Phone： Lit green when the phone is off-hook.

10 LINE：

Lit when the inbound and outbound calls transmitted

through PSTN.

11 VoIP： Lit when SIP registration is OK. 12 PPP： Steady glow when there is a PPPoA / PPPoE connection.

13 ADSL：

Lights when successfully connected to an ADSL DSLAM

(linesync).

2.4 The Rear Ports

Port Description

Power Switch

2 PWR

3 RESET

LAN

Phone

6 LINE

Power ON/OFF switch. Connect the supplied power adapter to this jack.

After the router is powered on, press this recessed button using the end of paper clip or other small pointed object to reset the router or to restore it to factory default settings.

1. Recovery procedures for non-working routers (e.g. after a failed firmware upgrade flash):

2. Recovery procedures for a lost web interface password: Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the

four LAN ports when connecting to a PC or an office/home network of 10Mbps or 100Mbps.

Connect RJ-11 cable to this port when connecting to an analog phone set.

Connect RJ-11 cable to this port when connecting to the telephone wall jack

7 ADSL

Antenna (7300VGP only)

Connect the supplied RJ-11 (“telephone”) cable to this port when connecting to the ADSL/telephone network.

Connect the detachable antenna to this port.

The detail instruction in Emergency/Failure Recovery Button

1. Recovery procedures for non-working routers (e.g. after a failed firmware upgrade flash): Hold the Emergency/Failure Recovery Button on the back of the modem in. Keep this button held in and turn on the modem. Once the lights on the modem have stopped flashing, release the Emergency/Failure Recovery Button. The modem's emergency-reflash web interface will then be accessible via

http://192.168.1.254/ where you can upload a firmware

image to restore the modem to a functional state. Please note that the modem will only respond via its web interface at this address, and will not respond to ping requests from your PC or to telnet connections.

2. Recovery procedures for a lost web interface password: After turning the router on press the Emergency/Failure Recovery Button on the back of the modem, and hold the button in until all lights on the modem flash and it reboots with factory default settings. The login will be reset to admin and the password will be reset to admin, and the modem will be accessible via its default IP address at http://192.168.1.254/

Before powered on the router to enter the recovery process. please configure the IP address of the PC as 192.168.1.1 and process step by step.

1. Power the router off.

2. Hold the " Emergency/Failure Recovery Button”.

3. Power on the router. Then Router's IP will reset to Default (Say

192.168.1.254)

4. Download the firmware.

2.5 Cabling

One of the most common causes of problems is bad cabling or ADSL line(s). Make sure that all connected devices are turned on. On the front of the product is a bank of LEDs. V erify that the LAN Link and ADSL line LEDs are lit. If they are not, verify that you are using the proper cables.

Ensure that all other devices connected to the same telephone line as your Billion router (e.g. telephones, fax machines, analog modems) have a line filter connected between them and the wall socket (unless you are using a Central Splitter or Central Filter installed by a qualified and licensed electrician), and ensure that all line filters are correctly installed and the right way around. Missing line filters or line filters installed the wrong way around can cause problems with your ADSL connection, including frequent disconnections.

Chapter 3

Installation

You can configure the BiPAC 7300VGP series router through the convenient and user-friendly interface of a web browser. Most popular operating systems such as Linux and Windows 98/NT/2000/XP/Me include a web browser as a standard application.

3.1 Before Configuration

PCs must have a properly installed Ethernet interface and connect to the router directly or through an external repeater hub. In addition, PCs must have TCP/IP installed and configured to obtain an IP address through a DHCP server or a fixed IP address that must be in the same subnet as the router. The default IP address of the router is 192.168.1.254 and the subnet mask is 255.255.255.0 (i.e. any attached PC must be in the same subnet, and have an IP address in the range of 192.168.1.1 to 192.168.1.253). The easiest way is to configure the PC to obtain an IP address automatically from the router using DHCP. If you encounter any problems accessing the router’s web interface you are advised to uninstall any kind of software firewall on your PCs, as they can cause problems accessing the 192.168.1.254 IP address of the router.

Please follow the steps below for installation on your PC’s network environment. First of all, check your PC’s network components. The TCP/IP protocol stack and Ethernet network adapter must be installed. If not, please refer to your Windows-related or other operating system manuals.

ny TCP/IP capable workstation can be used to communicate with o through the BiPAC 7300VGP series. To configure other types of workstations, please consult the manufacturer’s documentation.

Configuring a PC in Windows XP

1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections

2. Double-click Local Area Connection.

3. In the Local Area Connection Status window, click Properties.

4. Select Internet Protocol (TCP/IP) and click Properties.

5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio

buttons.

6. Click OK to finish the configuration.

Configuring a PC in Windows 2000

1. Go to Start / Settings / Control Panel.

In the Control Panel, double-click on

Network and Dial-up Connections.

2. Double-click Local Area Connection.

3. In the Local Area Connection Status window click Properties.

4. Select Internet Protocol (TCP/IP) and click Properties.

5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio

buttons.

6. Click OK to finish the configuration.

Configuring PC in Windows 98/Me

1.Go to Start / Settings / Control Panel.

In the Control Panel, double-click on

Network and choose the Configuration tab.

2.Select TCP/IP ->NE2000 Compatible,

or the name of your Network Interface Card (NIC) in your PC.

3.Select the Obtain an IP address automatically radio button.

4.Then select the DNS Configuration

tab.

5.Select the Disable DNS radio button and click OK to finish the configuration.

Configuring PC in Windows NT4.0

1.Go to Start / Settings / Control Panel.

In the Control Panel, double-click on

Network and choose the Protocols tab.

2.Select TCP/IP Protocol and click Properties.

3.Select the Obtain an IP address from a DHCP server radio button and click OK.

3.2 Factory Default Settings

Before configuring the BiPAC 7300VGP series router, you need to know the following default settings.

Web Interface:

Username: admin Password: admin

LAN Device IP Settings:

IP Address: 192.168.1.254

Subnet Mask: 255.255.255.0

ISP setting in WAN site:

PPPoE

DHCP Server:

DHCP server is enabled. Start IP Address: 192.168.1.100

IP pool counts: 100

3.3 LAN and WAN Port Addresses

The parameters of LAN and WAN ports are preset at the factory. The default values are shown below.

LAN Port WAN Port IP address Subnet Mask DHCP server function

192.168.1.254

255.255.255.0 Enabled

The PPPoE function is enabled to automatically get the WAN port

IP addresses for distribution to PCs

100 IP addresses continuing from

192.168.1.100 through

192.168.1.199

configuration from the ISP, but you have to set the username and password first.

3.4 Information from your ISP

Before configuring this device, you have to check with your ISP (Internet Service Provider) what kind of service is provided such as PPPoE, PPPoA, RFC1483, or IPoA.

Gather the information as illustrated in the following table and keep it for reference.

PPPoE VPI/VCI, VC-based/LLC-based multiplexing, Username, Password,

Service Name, and Domain Name System (DNS) IP address (it can be automatically assigned by your ISP when you connect or be set manually).

PPPoA VPI/VCI, VC-based/LLC-based multiplexing, Username, Password, and

Domain Name System (DNS) IP address (it can be automatically assigned by your ISP when you connect or be set manually).

RFC1483 Bridged VPI/VCI, VC-based/LLC-based multiplexing to use Bridged Mode.

RFC1483 Routed VPI/VCI, VC-based/LLC-based multiplexing, IP address, Subnet mask,

Gateway address, and Domain Name System (DNS) IP address (it is fixed IP address).

IPoA VPI/VCI, VC-based/LLC-based multiplexing, IP address, Subnet mask,

Gateway address, and Domain Name System (DNS) IP address (it is fixed IP address).

3.5 Configuring with your (802.11g) ADSL2+ Router

1. To configure this device, you must have IE 5.0 / Netscape 4.5 or above installed

2. You may configure the router for Internet access in two ways:

Easy Sign-On (EZSO) Web Configuration

Easy Sign-On:

User just installs all of cables and uses the browser to surf Internet. At this time, the EZSO WEB GUI will be popped up and request you to input some basic information you get from ISP. After this, you can surf Internet right away.

PPPoE /PPPoA With EZSO built-in, you can simply plug cables in as first installation and turn on host computer to surf Internet through WEB browser like IE. You do not need to login into the router and search the router’s WEB GUI configuration page to find out the right web page for configuring your PPPoE/PPPoA credentials. EZSO feature in Billion’s routers will do it for you. When you are trying to surf the internet through WEB browser, the PPPoE dialogue will be visible and nothing but that. After you have successfully submitting the credentials, everything will be fine and work neatly.

1. Please wait when the connection is trying. 2.Enter the username and password provide by your ISP.

3. If login failed, Please input the correct

4. Login Successfully.

username and password again.

DHCPWith this method, user does not need to access router to configure it and set lot of

parameters. Besides, it eliminates the complicated way to configure the device and will definitely reduce the service call from users.

1. Please wait when the connection is trying. 2. Login Successfully.

Web Configuration:

Open your web browser, enter the IP address of your router, which by default is

192.168.1.254, and click “Go”, a user name and password window prompt appears. The default username and password are “admin” and “admin”.

Congratulations! You have successfully logged on to your BiPAC 7300 series ADSL2+ Router!

Chapter 4

Configuration

Once you have logged on to your BiPAC 7300VGP series VoIP ADSL Router via your web browser, you can begin to set it up according to your requirements. On the configuration homepage, the left navigation pane links you directly to the setup pages, which include:

Status (ARP Table, Wireless Association, Routing Table, DHCP Table, System Log,

Security Log, VoIP Log)

Quick Start Configuration (LAN, WAN, System, Firewall, QoS, Virtual Server, Advanced and VoIP) Save Config to FLASH

The following sections provide an overview of the settings available for configuring your router by Billion.

4.1 Status

Device Information

Host Name: Provide a name for the router for identification purposes. Host Name lets

you change the router name.

System Up-Time: Records system up-time.

Current time: Set the current time. See the Time Zone section for more information. Hardware Version: Chipset version Software Version: Firmware version Bootrom Version: Bootrom version MAC Address: The LAN MAC address

Home URL: Connects to the Home Website.

LAN

IP Address: LAN port IP address. Sub Net Mask: LAN port IP subnet mask.

DHCP Server: LAN port DHCP role - Server, Relay or None.

WAN

IP WAN: Name of the WAN connection. VPI/VCI: Virtual Path Identifier and Virtual Channel Identifier Connection: Selects “Disconnected” or “Connected” IP Address: WAN port IP address.

Net mask: WAN port IP subnet mask. Gateway: The IP address of the default gateway.

Port Status：User can look up for your connected condition

+ 96 hidden pages