Billion Electric Company 400G User Manual

Table of Contents

CHAPTER 1: INTRODUCTION ...............................................................................................................................................1

INTRODUCTION TO YOUR ROUTER.....................................................................................................................................1

FEATURES ................................................................................................................................................................................1

CHAPTER 2: INSTALLING THE ROUTER ...........................................................................................................................3

IMPORTANT NOTE FOR USING THIS ROUTER ...................................................................................................................3

PACKAGE CONTENTS .............................................................................................................................................................3

THE FRONT LEDS ...................................................................................................................................................................4

THE REAR PORTS ....................................................................................................................................................................5

CABLING ..................................................................................................................................................................................6

CHAPTER 3: BASIC INSTALLATION ....................................................................................................................................7

CONNECTING YOUR ROUTER ..............................................................................................................................................8

FACTORY DEFAULT SETTINGS ............................................................................................................................................ 13

Web Interface (Username and Password) .......................................................................................................................... 13

Device LAN IP settings ....................................................................................................................................................... 13

ISP setting in WAN site ....................................................................................................................................................... 13

DHCP server ...................................................................................................................................................................... 13

LAN and WAN Port Addresses ............................................................................................................................................ 13

INFORMATION FROM YOUR ISP ........................................................................................................................................ 14

CONFIGURING WITH YOUR WEB BROWSER .................................................................................................................... 15

CHAPTER 4: CONFIGURATION .......................................................................................................................................... 16

STATUS ................................................................................................................................................................................... 17

ADSL Status ........................................................................................................................................................................ 17

ARP Table ........................................................................................................................................................................... 17

DHCP Table........................................................................................................................................................................ 18

Routing Table ...................................................................................................................................................................... 18

NAT Sessions ...................................................................................................................................................................... 19

UPnP Portmap ................................................................................................................................................................... 19

Email Status ........................................................................................................................................................................ 19

Event Log ............................................................................................................................................................................ 20

Error Log ............................................................................................................................................................................ 20

Diagnostic .......................................................................................................................................................................... 20

QUICK START ........................................................................................................................................................................ 21

CONFIGURATION ................................................................................................................................................................. 24

LAN - Local Area Network ................................................................................................................................................. 24

Bridge Interface ............................................................................................................................................................. 24

Ethernet .......................................................................................................................................................................... 25

IP Alias ........................................................................................................................................................................... 25

Ethernet Client Filter ..................................................................................................................................................... 26

Wireless ......................................................................................................................................................................... 27

Wireless Security ........................................................................................................................................................... 29

Wireless Client / MAC Address Filter ........................................................................................................................... 31

WPS ............................................................................................................................................................................... 32

Port Setting .................................................................................................................................................................... 32

DHCP Server ................................................................................................................................................................. 33

WAN - Wide Area Network .................................................................................................................................................. 34

WAN Profile .................................................................................................................................................................. 34

ADSL Mode ................................................................................................................................................................... 40

System ................................................................................................................................................................................. 41

Time Zone ...................................................................................................................................................................... 41

Remote Access ............................................................................................................................................................... 42

Firmware Upgrade ......................................................................................................................................................... 42

Table of Contents i

Backup / Restore ............................................................................................................................................................ 43

Restart Router ................................................................................................................................................................ 44

User Management .......................................................................................................................................................... 44

Firewall and Access Control .............................................................................................................................................. 46

General Settings ............................................................................................................................................................. 47

(Changed the format only.) ............................................................................................................................................ 47

Packet Filter ................................................................................................................................................................... 48

Intrusion Detection ........................................................................................................................................................ 55

URL Filter ...................................................................................................................................................................... 58

IM / P2P Blocking ......................................................................................................................................................... 60

Firewall Log................................................................................................................................................................... 61

QoS - Quality of Service ..................................................................................................................................................... 61

Prioritization .................................................................................................................................................................. 61

Outbound IP Throttling (LAN to WAN) ........................................................................................................................ 63

Inbound IP Throttling (WAN to LAN) ........................................................................................................................... 64

Virtual Server (known as Port Forwarding) ....................................................................................................................... 69

Add Virtual Server ......................................................................................................................................................... 69

Edit DMZ Host .............................................................................................................................................................. 71

Edit DMZ Host .............................................................................................................................................................. 72

Edit One-to-One NAT (Network Address Translation) .................................................................................................. 73

Time Schedule ..................................................................................................................................................................... 75

Configuration of Time Schedule .................................................................................................................................... 76

Advanced ............................................................................................................................................................................ 77

Static Route .................................................................................................................................................................... 77

Dynamic DNS ................................................................................................................................................................ 78

Check Email................................................................................................................................................................... 79

Device Management ...................................................................................................................................................... 80

IGMP ............................................................................................................................................................................. 83

VLAN Bridge ................................................................................................................................................................ 83

LOGOUT ................................................................................................................................................................................. 83

CHAPTER 5: TROUBLESHOOTING .................................................................................................................................... 84

PROBLEMS STARTING UP THE ROUTER ........................................................................................................................... 84

PROBLEMS WITH THE WAN INTERFACE ........................................................................................................................... 84

PROBLEMS WITH THE LAN INTERFACE ............................................................................................................................ 84

CONTACT TELKOM ADSL SUPPORT .................................................................................................................................. 85

CONTACT SIZWEBROADBAND FOR ROUTER SUPPORT ................................................................................................. 85

Table of Contents ii

Introduction to your Router

Billion 400G Router

Chapter 1: Introduction

Your Billion 400G router is an “all-in-one” ADSL router, switch

, providing everything you need to you connected to the Internet using your ADSL connection.

combining an ADSL

2/2+

modem/router and network

Features

Express Internet Access

The router complies with ADSL worldwide standards. It supports downstream rate up to 12/24 Mbps with

ADSL2/2+, 8Mbps with ADSL. Users enjoy not only high-speed ADSL services but also broadband

multimedia applications such as interactive gaming, video streaming and real-time audio much easier and faster than ever. It is compliant with Multi-Mode standard (ANSI T1.413, Issue 2; G.dmt (ITU G.992.1); G.lite

(ITU G.992.2); G.hs (ITU G994.1); G.dmt.bis (ITU G.992.3); G.dmt.bis.plus (ITU G.992.5)).

802.11g Wireless AP with WPA Support

With integrated 802.11g Wireless Access Point in the router, the device offers a quick and easy access among wired network, wireless network and broadband connection (ADSL) with single device simplicity, and as a result, mobility to the users. In addition to 54 Mbps 802.11g data rate, it also interoperates backward with existing 802.11b equipment. The Wireless Protected Access (WPA1 and WPA2) and Wireless Encryption Protocol (WEP) supported features enhance the security level of data protection and access control via Wireless LAN.

Fast Ethernet Switch

A 4-port 10/100Mbps fast Ethernet switch is built in with automatic switching between MDI and MDI-X for 10Base-T and 100Base-TX ports. An Ethernet straight or crossover cable can be used directly for auto detection.

Multi-Protocol to Establish a Connection

It supports PPPoA, RFC 1483 encapsulation over ATM (bridged or routed), PPP over Ethernet (RFC 2516), and IPoA to establish a connection with the ISP. The product also supports VC-based and LLC-based multiplexing. smart traffic separation.

Quick Installation Wizard

The router can be setup and managed by using the easy setup wizard software included on the CD or the GUI (Graphical User Interface) imbedded on the router accessed using the router’s LAN IP address and a standard web-browser application like Internet Explorer.

Universal Plug and Play (UPnP) and UPnP NAT Traversal

This protocol is used to enable simple and robust connectivity among stand-alone devices and PCs from many different vendors. It makes network simple and affordable for users. UPnP architecture leverages TCP/IP and the Web to enable seamless proximity networking in addition to control and data transfer among networked devices. With this feature enabled, users can now connect to Net meeting or MSN Messenger seamlessly.

Network Address Translation (NAT)

Allows multi-users to access outside resources such as the Internet simultaneously with one IP address/one Internet access account. Many application layer gateways (ALG) are supported such as web browser, ICQ, FTP, Telnet, E-mail, News, Net2phone, Ping, NetMeeting, IP phone and others.

SOHO Firewall Security with DoS and SPI

Along with the built-in NAT natural firewall feature, the router also provides advanced hacker pattern-filtering protection. It can automatically detect and block Denial of Service (DoS) attacks. The router is built with Stateful Packet Inspection (SPI) to determine if a data packet is allowed through the firewall to the private LAN.

Furthermore the device supports multiple PPPoE connections on the same PVC to allow for

Chapter 1: Introduction

Billion 400G Router

Domain Name System (DNS) Relay

It provides an easy way to map the domain name (a friendly name for users such as www.yahoo.com) and IP address. When a local machine sets its DNS server with this router’s IP address, every DNS conversion request packet from the PC to this router will be forwarded to the real DNS in the outside network.

Dynamic Domain Name System (DDNS)

The Dynamic DNS service allows you to alias a dynamic WAN IP address to a static hostname. example, to use the service, you must first apply for an account from a DDNS service like http://www.dyndns.org/. More than 5 DDNS servers are supported.

Quality of Service (QoS)

QoS gives you full control over which types of outgoing data traffic should be given priority by the router, ensuring important data like gaming packets, customer information, or management information move through the router ay lightning speed, even under heavy load. The QoS features are configurable by source IP address, destination IP address, protocol, and port. You can throttle the speed at which different types of outgoing data pass through the router, to ensure P2P users don’t saturate upload bandwidth, or office browsing doesn’t bring client web serving to a halt. In addition, or alternatively, you can simply change the priority of different types of upload data and let the router sort out the actual speeds.

Virtual Server (“port forwarding”)

Users can specify some services to be visible from outside users. The router can detect incoming service requests and forward either a single port or a range of ports to the specific local computer to handle it. For example, a user can assign a PC in the LAN acting as a WEB server inside and expose it to the outside network. Outside users can browse inside web servers directly while it is protected by NAT. A DMZ host setting is also provided to a local computer exposed to the outside network, Internet.

For

Rich Packet Filtering

Not only filters the packet based on IP address, but also based on Port numbers. It will filter packets from and to the Internet, and also provides a higher level of security control.

Dynamic Host Configuration Protocol (DHCP) Client and Server

In the WAN site, the DHCP client can get an IP address from the Internet Service Provider (ISP) automatically. In the LAN site, the DHCP server can allocate a range of client IP addresses and distribute them including IP address, subnet mask as well as DNS IP address to local computers. It provides an easy way to manage the local IP network.

Static and RIP1/2 Routing

It has routing capability and supports easy static routing table or RIP1/2 routing protocol.

Simple Network Management Protocol (SNMP)

It is an easy way to remotely manage the router via SNMP.

Web based GUI

The routers’ web based GUI is used for configuration and management. It is user-friendly and comes with on-line help. It also supports remote management capability for remote users to configure and manage the router.

Firmware Upgradeable

Device can be upgraded to the latest firmware through the WEB based GUI.

Rich Management Interfaces

It supports flexible management interfaces with local console port, LAN port, and WAN port. Users can use terminal applications through the console port to configure and manage the device, or Telnet, WEB GUI, and SNMP through LAN or WAN ports to configure and manage the device. supported, but is normally implemented by Telkom or your ISP.

TR-069 management is also

Chapter 1: Introduction

Important note for using this router

Do not use this router

under

high humidity or high temperatures.

Attention

Warning

Package Contents



 Do not use the same power source for this router as other equipment.

 Do not open or repair the case by yourself. If this router is too hot, turn

off the power immediately and have it repaired at a qualified service

center.

 Avoid using this product and all accessories outdoors.

 Place this router on a stable surface.

 Only use the power adapter that comes with the package.

Using a different voltage rating power adaptor may damage this router.

Billion 400G Router

Chapter 2: Installing the Router

• Billion 400G Router

• CD-ROM containing this online manual

• 2 x RJ-11 ADSL/telephone Cable

• Ethernet (CAT-5 LAN) Cable

• Console tool kit

• Integrated surge and AC-DC power adapter (12VDC, 1.2A)

• A detachable antenna

• ADSL Micro filter

• ADSL Splitter

• Quick Start Guide

Chapter 2: Installing the router

The Front LEDs

2 4 5 6 3

Billion 400G Router

LED Meaning

Lit when power is ON.

1 Power

LAN Port

3 Wireless

4 Mail Lit and flashing periodically when there are emails in the Inbox.

5 ADSL

6 Internet

1X — 4X

(RJ-45 connector)

If lit red it means the system has failed to load. Restart the device or contact router support.

Lit when connected to an Ethernet device.

Green for 100Mbps; Orange for 10Mbps.

Flashing

Green when the wireless connection is established.

Flashing when sending/receiving data.

Lit Green when the device is successfully connected to an ADSL DSLAM (“line synch”).

Lit red when WAN port fails to get IP address. Lit green when WAN port gets IP address successfully.

when data is Transmitted / Received.

Chapter 2: Installing the router

The Ethernet

Port #

4 can be

used as a

console

port

. You need a special console

The Rear Ports

port to

ogin to the router

3 1 2

6 7

tool which already includes in the package to connect with LAN port 4 and PC’s RS-232 port (9-pin serial port).

Billion 400G Router

Port

Antenna Connect the detachable antenna to this port.

ADSL

LAN

1X — 4X (RJ-45 connector)

4 WPS

5 RESET

Power

Use the supplied RJ-11 (“telephone”) cable to connect this the ADSL/telephone wall jack.

To connect your router to a PC or an office/home network of 10Mbps or 100Mbps use a UTP Ethernet cable (Cat-5 or Cat-5e) and connect to one of the LAN ports.

Caution:

not simultaneously.

Press the WPS button to trigger Wi-Fi Protected Setup function.

When the router is turned on Reset the router: press for 1-3 seconds Restore

power cycle the router:

or have forgotten your Username/Password.)

Caution:

you power cycle the device. If the RESET button is pressed for more than 10 seconds, the device will need to be power cycled before normal operation can be resumed.

Connect the supplied power adapter to this jack.

Port 4 can be either a LAN or a Console port at any time but

 the reset button is used to:

factory default

After pressing the RESET button for 6 - 8 seconds, be sure

settings: press for

(useful if you cannot l

6 – 8

seconds, and

Power Switch

Chapter 2: Installing the router

Power ON/OFF switch

Billion 400G Router

Cabling

One of the most common causes of problems is the bad cabling or ADSL line(s). Make sure that all connected devices are turned on. On the front of the product is a bank of LEDs. Verify that the LAN Link and ADSL line LEDs are lit. If they are not, verify that you are using the proper cables.

Ensure that all other devices connected to the same telephone line as your router (e.g. telephones, fax machines, analogue modems) have a line filter connected between them and the wall socket (unless you are using a Central Splitter or Central Filter installed by a qualified and licensed electrician), and ensure that all line filters are correctly installed and the right way around. Missing line filters or line filters installed the wrong way around can cause problems with your ADSL connection, including causing frequent disconnections.

Chapter 2: Installing the router

Billion 400G Router

Any TCP/IP capable workstation can be used to communicate with or

Chapter 3: Basic Installation

The router can be configured with your web browser. A web browser is included as a standard application in the following operating systems: Linux, Mac OS, Windows 98/NT/2000/XP/Me, etc. The product provides an easy and user-friendly interface for configuration.

Please check your PC’s network components. The TCP/IP protocol stack and Ethernet network adapter must be installed. If not, please refer to your Windows-related or other operating system manuals.

You can connect your computer to the router either through an external hub/switch or directly. However, please ensure that your computer has a properly installed Ethernet interface prior to connecting it to the router. You ought to configure your Computers to obtain an IP address through a DHCP server or you can set them up with a fixed IP address that must be in the same subnet as the router. The default IP address of the router is 10.0.0.2 and the subnet mask is 255.255.255.0 (i.e. any attached Computer must be in the same subnet, and have an IP address in the range of 10.0.0.1 to10.0.0.254). The best and easiest way is to configure the PC to get an IP address automatically from the router using DHCP. If you encounter any problem accessing the router’s web interface it may also be advisable to temporarily remove any kind of software firewall on your Computer’s as they can cause problems accessing the 10.0.0.2 IP address of the router. Users should always make their own decisions on how to best protect their network.

Please follow the steps below for your PC’s network environment installation.

through the router. To configure other types of workstations, please consult the manufacturer’s documentation.

Chapter 3: Basic Installation

Billion 400G Router

Connecting Your Router

1. Connect the power adapter as illustrated below steadily.

Connect your network or computer to the router using the LAN (Local Area Network)

Connect the ADSL/telephone (

ADSL)

cable to the router’s DSL port as illustrated below.

and power on the device, m

ake sure that the PWR LED is

cable.

lit

Chapter 3: Basic Installation

Billion 400G Router

Configuring PCs in Windows in Window XP

1. Go to Start / Control Panel (in Classic View). In the Control Panel,

double-click Network Connections.

2. Double-click Local Area Connection. (See Figure 3.1)

3. In the LAN Area Connection Status window, click Properties.

(See Figure 3.2)

4. Select Internet Protocol (TCP/IP) and click Properties. (See

Figure 3.3)

5. Select the Obtain an IP address automatically and Obtain DNS

server address automatically radio buttons. (See Figure 3.4)

6. Click OK to finish the configuration.

Figure 3.1: LAN Area Connection

Figure 3.2: LAN Connection Status

Figure 3.3: TCP / IP

Figure 3.4: IP Address & DNS

Configuration

Chapter 3: Basic Installation

Billion 400G Router

Configuring PCs in Windows 2000

Go to Start / Settings / Control Panel. In the Control Panel, double-click Network and Dial-up Connections.

Double-click Local Area (“LAN”) Connection. (See Figure 3.5)

In the LAN Area Connection Status window, click Properties. (See Figure 3.6)

Select Internet Protocol (TCP/IP) and click Properties. (See Figure 3.7)

Select the Obtain an IP address automatically and Obtain DNS server address automatically radio buttons. (See Figure 3.8)

Click OK to finish the configuration.

Figure 3.5: LAN Area Connection

Figure 3.6: LAN Connection Status

Figure 3.7: TCP / IP

Figure 3.8: IP Address & DNS

Configuration

Chapter 3: Basic Installation

Billion 400G Router

Configuring PC in Windows 95/98/ME

1. Go to Start / Settings / Control Panel. In the Control Panel,

double-click Network and choose the Configuration tab.

2. Select TCP / IP -> NE2000 Compatible, or the name of any

Network Interface Card (NIC) in your PC. (See Figure 3.9)

3. Click Properties.

4. Select the IP Address tab. In this page, click the Obtain an IP

address automatically radio button. (See Figure 3.10)

5. Then select the DNS Configuration tab. (See Figure 3.11)

6. Select the Disable DNS radio button and click OK to finish the

configuration.

Figure 3.9: TCP / IP

Figure 3.10: IP Address

Figure 3.11: DNS Configuration

Chapter 3: Basic Installation

Billion 400G Router

Configuring PC in Windows NT4.0

Go to Start / Settings / Control Panel. In the Control Panel, double-click Network and choose the Protocols tab.

Select TCP/IP Protocol and click Properties. (See Figure 3.12)

Select the Obtain an IP address from a DHCP server radio button and click OK. (See Figure 3.13)

Figure 3.12: TCP / IP

Figure 3.13: IP Address

Chapter 3: Basic Installation

Billion 400G Router

LAN Port

WAN Port

Attention

Factory Default Settings

Before configuring your, you need to know the following default settings.

Web Interface (Username and Password)

Username: admin

Password: admin

The default username and password are “admin” and “admin” respectively.

Device LAN IP settings

IP Address: 10.0.0.2

Subnet Mask: 255.255.255.0

If you ever forget the username/password to login to the router, you may press the RESET button for 6 – 8 seconds to restore the factory default settings.

Caution: After pressing the RESET button for more than 6 seconds, to be sure you power

cycle the device again.

ISP setting in WAN site

PPPoE

DHCP server

DHCP server is enabled.

Start IP Address: 10.0.0.100

IP pool counts: 100

LAN and WAN Port Addresses

The parameters of LAN and WAN ports are pre-set in the factory. The default values are shown below.

IP address

Subnet Mask

DHCP server function

IP addresses for distribution to PCs

10.0.0.2

255.255.255.0

Enabled

100 IP addresses continuing from

10.0.0.100 through 10.0.0.199

The

WAN protocol has been pre-selected and set by Telkom for automated service deployment and delivery.

Chapter 3: Basic Installation

Information from your ISP

Billion 400G Router

Telkom ADSL connections use PPPoE, and automatically assign a WAN IP address to your router. The following information is provided should you wish to connect to an alternative ISP.

Gather the information as illustrated in the following table and keep it for reference.

PPPoE

PPPoE (Multisession)

PPPoE / PPPoE with Pass-through

PPPoA

VPI/VCI, VC / LLC-based multiplexing, Username, Password, Service Name, and Domain Name System (DNS) IP address (this is automatically set by the Telkom network but be set manually should this be required).

VPI/VCI, VC / LLC-based multiplexing, Username, Password, Service Name, Domain Name System (DNS) IP address and multiple-sessions on the same PVC.

VPI/VCI, VC / LLC-based multiplexing, Username, Password, Service Name, and Domain Name System (DNS) IP address (this is automatically set by the Telkom network address can be assigned using PPPoE dialer.

VPI/VCI, VC / LLC-based multiplexing, Username, Password and Domain Name System (DNS) IP address (it can be automatically assigned by your ISP when you connect or be set manually).

but be set manually should this be required). In addition, additional WAN

RFC 1483 Bridged

RFC 1483 Routed

IPoA Routed (IP over ATM)

VPI/VCI, VC / LLC-based multiplexing to use Bridged Mode.

VPI/VCI, Gateway address, is

VC /

fixed

IP address).

VC /

fixed

IP address).

LLC-based

and

LLC-based

and

Domain

multiplexing,

Name

multiplexing,

Name

System

address,

(DNS)

address,

(DNS)

Subnet

address

mask,

(it

mask,

(it

Chapter 3: Basic Installation

Billion 400G Router

Configuring with your Web Browser

Open your web browser, enter the IP address of your router, which by default is 10.0.0.2, and click “Go”, a user name and password window prompt will appear. The default username and password are “admin” and “admin” respectively. (See Figure 3.14)

Figure 3.14: User name & Password Prompt Window

Congratulations! You are now successfully logged on to the Router!

Chapter 3: Basic Installation

Billion 400G Router

Chapter 4: Configuration

At the configuration homepage, the left navigation pane where bookmarks are provided links you directly to the desired setup page, including:

Status

- ADSL Status

- ARP Table

- DHCP Table

- Routing Table

- NAT Sessions

- UPnP Portmap

- Email Status

- Event Log

- Error Log

- Diagnostic

Quick Start

Configuration

- LAN

- WAN

- System

- Firewall

- VPN

- QoS

- Virtual Server

- Time Schedule

- Advanced

Language (provides user interface in English and French languages)

Chapter 4: Configuration

Billion 400G Router

Status

ADSL Status

This section displays the ADSL overall status, which shows a number of helpful information such as DSP firmware version.

ARP Table

This section displays the router’s ARP (Address Resolution Protocol) Table, which shows the mapping of Internet (IP) addresses to Ethernet (MAC) addresses. This is useful as a quick way of determining the MAC address of the network interface of your PCs to use with the router’s Firewall – MAC Address Filter function. See the Firewall section of this manual for more information on this feature.

IP Address: A list of IP addresses of devices on your LAN (Local Area Network).

MAC Address: The MAC (Media Access Control) addresses for each device on your LAN.

Interface: The interface name (on the router) that this IP Address connects to.

Static: Static status of the ARP table entry:



“no” for dynamically-generated ARP table entries.



“yes” for static ARP table entries added by the user.

Chapter 4: Configuration

DHCP Table

Leased: The DHCP assigned IP addresses information.

Expired: The expired IP addresses information.

Billion 400G Router

Permanent: The fixed host mapping information

Leased Table

IP Address: The IP address that assigned to client.

MAC Address: The MAC address of client.

Client Host Name: The Host Name (Computer Name) of client.

Expiry: The current lease time of client.

Routing Table

Valid: It indicates a successful routing status.

Destination: The IP address of the destination network.

Netmask: The destination Netmask address.

Gateway/Interface: The IP address of the gateway or existing interface that this route will use.

Cost: The number of hops counted as the cost of the route.

RIP Routing Table

Destination: The IP address of the destination network.

Netmask: The destination Netmask address.

Gateway: The IP address of the gateway that this route will use.

Cost: The number of hops counted as the cost of the route.

Chapter 4: Configuration

Billion 400G Router

NAT Sessions

This section lists all current NAT sessions between interface of types external (WAN) and internal (LAN).

UPnP Portmap

The section lists all port-mapping established using UPnP (Universal Plug and Play. See the Advanced section of this manual for more details on UPnP and the router’s UPnP configuration options.

Email Status

Details and status for the Email Account you have configured the router to check. Please see the Advanced section of this manual for details on this function.

Chapter 4: Configuration

Billion 400G Router

Event Log

This page displays the router’s Event Log entries. Major events are logged to this window, such as when the router’s ADSL connection is disconnected, as well as Firewall events when you have enabled Intrusion or Blocking Logging in the Configuration – Firewall section of the interface. Please see the Firewall section of this manual for more details on how to enable Firewall logging.

Error Log

Any errors encountered by the router (e.g. invalid names given to entries) are logged to this window.

Diagnostic

It tests the connection to computer(s) which is connected to LAN ports and also the WAN Internet connection. If PING www.google.com is shows as FAIL and the rest show as PASS, you ought to check your PC’s DNS settings is set correctly.

Chapter 4: Configuration

Billion 400G Router

Quick Start

1. Click Quick Start. Select the connect mode you want. There are two options you can choose, ADSL. Select ADSL from Connect Mode drop-down menu, and click Continue.

2. If your ADSL line is not ready, you need to check your ADSL line has been set or not.

3. If your ADSL line is ready, the screen appears ADSL Line is Ready. Choose Auto radio button and click Apply. It will automatically scan the recommended mode for you. Manually mode makes you to set the ADSL line by manual. (If you choose Manually, you will directly go to step 5.)

Chapter 4: Configuration

Billion 400G Router

4. The list below has different mode applied for your choice. Choose 0/33/PPPoE(Recommended) and click Apply.

5. Please enter “Username” and “Password” as supplied by your ISP(Internet Service Provider) and click Apply to continue.

Profile Port: Select the connection mode. There isADSL.

Encapsulation: Select the encapsulation mode. The default mode is PPPoE.

VPI/VCI: Enter the VPI and VCI information provided by your ISP.

Username: Enter the username provided by your ISP.

Password: Enter the password provided by your ISP.

Service Name: This item is for identification purposes. If it is required, your ISP provides you the information.

Authentication Protocol: Default is Auto. Your ISP advises on using Chap or Pap.

IP Address: Your WAN IP address. Leave this at 0.0.0.0 to obtain automatically an IP address from your ISP.

Chapter 4: Configuration

Billion 400G Router

6. Configure the Wireless LAN setting.

WLAN Service: Default setting is set to Enable. If you want to use wireless, both 802.11g and 802.11b device in your network, you can select Enable. ESSID: The ESSID is the unique name of a wireless access point (AP) to be distinguished from another. For security propose, change to a unique ID name to the AP which is already built-in to the router’s wireless interface. It is case sensitive and must not excess 32 characters. Make sure your wireless clients have exactly the ESSID as the device, in order to get connected to your network. ESSID Broadcast: It is function in which transmits its ESSID to the air so that when wireless client searches for a network, router can then be discovered and recognized. Default setting is Enable.

 Enable: When Enable is selected, you can allow anybody with a wireless client to be able to locate the

Access Point (AP) of your router.

 Disable: Select Disable if you do not want broadcast your ESSID. When select Disable, no one will be

able to locate the Access Point (AP) of your router.

Channel ID: Select the ID channel that you would like to use.

Security Mode: You can disable or enable with WPA or WEP for protecting wireless network. The default mode of

wireless security is Disable.

7. Wait for the configuration.

Chapter 4: Configuration

Billion 400G Router

8. When ADSL is synchronic, it will appear “check”.

Configuration

When you click this item, you get following sub-items to configure the ADSL router.

- LAN, WAN, System, Firewall, VPN, QoS, Virtual Server, Time Schedule and Advanced

These functions are described below in the following sections.

LAN - Local Area Network

Here are the items within the LAN section:

Bridge Interface Ethernet IP Alias Ethernet Client Filter Wireless Wireless Security Wireless Client Filter WPS Port Settings DHCP Server

Bridge Interface

Chapter 4: Configuration

+ 61 hidden pages