BiPAC 2073N
Wireless-N HomePlug AV 200
Wall Plug Ethernet Adapter
Quick Start Guide
Quick Start Guide
Billion BiPAC 2073N Wireless-N Homeplug AV 200 Wall Plug Ethernet Adapter
FCC Certifications
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Any changes or modifications not expressly approved by the party
responsible for compliance could void the authority to operate equipment. This equipment has been tested and
found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to
operate the equipment.
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used
for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not
be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be
provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure
compliance.
CE Mark Warning
This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class B for ITE,
the essential protection requirement of Council Directive2004/108/EC and Directive2006/95/EC, Standard
EN60950-1 on the approximation of the laws of the Member States relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible that information in this document
is not up-to-date. Please check with your local distributors for the latest information. No part of this document can be
copied or reproduced in any form without written consent from the company.
-1-
Quick Start Guide
Do no
t use the adapter
in high humidity or high temperatures.
Place the
adapter on
a stable surface.
Package Content
BiPAC 2073N Wireless-N HomePlug AV 200 Wall Plug Ethernet Adapter
Quick Start Guide
CD (containing user manual and QSG)
Ethernet (CAT-5 LAN) cable
Do not open or repair the case yourself.
Avoid using this product and all accessories outdoors.
Only “Homeplug AV” compliant Power Line Communication (PLC)
adapter for remote access is necessary
Warning
Attention
-2-
Billion BiPAC 2073N Wireless-N Homeplug AV 200 Wall Plug Ethernet Adapter
ETH:
PLC:
POWER
:
Ethernet Port
:
SYNC
:
* Power line sync
Reset Button
:
* Press the reset button more than 2 seconds
WLAN
:
WPS
:
Hardware Overview
The LEDs and Buttons
* Lit green when the wireless
function is enabled.
* Blinking when data is
transmitted or received.
* Blinking quickly when WPS
is proceeded.
* Lit green when
power is ON.
* Lit green when the power line
sync is established.
* Blinking when networking is
active.
The Ethernet Port and Reset Button
* Lit when connected to an
Ethernet device.
* Blinking when data is
transmitted or received via
Ethernet port.
* Push the WPS button to
trigger the Wi-Fi Protected
Setup function.
to reset device to factory default.
* Connect your device (e.g.: computer, router,
hub/switch , IP pone, IPTV set-top-box,
gaming consoles…) to a Ethernet port, using
the included RJ-45 Ethernet cable.
-3-
Quick Start Guide
Please
DO
NOT
remove or
disassemble the
socket
clip
Clip Socket
:
The Rear Side and Look After Installing with Clip
* Install the clip
into this socket.
frequently as this may cause serious damage to your
HomePlug AV device!
Warning
-4-
Billion BiPAC 2073N Wireless-N Homeplug AV 200 Wall Plug Ethernet Adapter
and direction to
and direction to
Clip Installation
Installing the clip with BiPAC 2073N.
Follow the diagrams
install the clip.
(This is an example of EU clip.
Please check the lock instruction on
your clip. If you got the “Triangle
Lock”, refer to right diagram.)
Follow the diagrams
install the clip.
(This is an example of UK clip.
Please check the lock instruction on
your clip. If you got the “Circle
Lock”, refer to right to diagram.)
-5-
Quick Start Guide
Hardware Installation
1. Power Connection
Plug BiPAC 2073N into the wall outlet/socket.
2. LAN & Wireless Connection
Connect the supplied RJ-45 Ethernet cable to the Ethernet port on BiPAC 2073N and the other
side to the device’s Ethernet interface. You can enable wireless function to connect to the Wi-Fi
devices through WPS configuration interface or by pushing the WPS button of your 2073N.
*For WPS configuration please refer to 2073N User Manual for more detail description.
3. Networking Setup
-6-
Billion BiPAC 2073N Wireless-N Homeplug AV 200 Wall Plug Ethernet Adapter
Configuring Web Browser
Open your web browser, enter the IP address of BiPAC 2073N which by default is 192.168.1.253,
and click “Go”, a user name and password window prompt will appear. The default username
and password are both “admin”.
You are now successfully logon to BiPAC 2073N as the Status screen shows.
Configuring Wireless
1. The WLAN Service is Enable as default setting.
2. The Network Name(SSID) is wlan_ap as default setting. Re-name your SSID if necessary.
-7-
Quick Start Guide
Product Application
Product Support and Contact Information
Most problems can be solved by referring to the Troubleshooting section in the User’s Manual.If you cannot resolve the
problem with the Troubleshooting chapter, please contact the dealer where you purchased this product.
Contact Billion WORLDWIDE http://www.billion.com
Billion Product Registration
Billion is committed to before and after sales customer services. You will get the most out of your Billion's products after registration. Please
register online at http://www.biguard.com/register/ to receive valuable services and support from us.
-8-
BiPAC 2073N V101EN
Loading...