Page 1
User guide
Billi B-1000
Page 2
User guide
Billi B-1000.
Contents
Warnings & Important information ........2
General Maintenance.....................3
Features and Modes......................3
Filtration Information.....................4
Changing the filter .......................4
Service Support .........................5
Warnings & Important information
– For continued safety of this appliance it
must be installed, operated and maintained
in accordance with the manufacturer's
instructions.
– Your appliance should be installed by
a suitably qualified tradesperson.
– For correct operation of this appliance
it is essential to observe the instructions
as outlined in this booklet.
– Do not use this appliance with water that
is microbiologically unsafe or with water
of unknown quality without adequate
disinfection before or after the system.
Systems certified for cyst reduction may
be used on disinfected water that may
contain filterable cysts.
– Filter replacement must be performed
at intervals of not more than 12 months.
– Use this appliance only as directed
in these instructions and only for its
designed purpose.
– This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use
of the appliance by a person responsible
for their safety.
– Children should be supervised to ensure
that they do not play with the appliance.
– If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in order
to avoid creation of a hazard.
– New hose sets supplied with the appliance
are to be used. Old hose sets should not be
re-used.
2
Page 3
User guide
Billi B-1000.
General Maintenance
Your Billi B-1000 has been designed to require
minimal maintenance other than replacement
of filter cartridges. During each filter change,
check all water connection fittings for signs
of leakage. Check all tubing for any signs of
damage. Check the cupboard area around
the base of unit for any signs of moisture.
Cleaning the dispenser
Your B-1000 Dispenser is fabricated from
robust metal with a tough protect chrome
plating. Care of dispenser is as with any
chrome plated tapware. Avoid using abrasive
cleaners. Wipe clean using a damp cloth.
Use of a non-solvent, non-smearing cleaner
such as Windex is recommended. Do not
pour water over dispenser.
Unit operation
Slimline Dispenser
To dispense filtered water, the dispenser
tap lever will need to be rotated. The lever
will automatically return to the o position.
The spout can be swivelled to suit your
installation.
3
Page 4
User guide
Billi B-1000.
Billi Filter Cartridges
The B-1000 features the Billi dual stage
filtration system. It is fitted with single
dual stage filter incorporating sediment and
chemical removal elements. All B-1000 filters
are manufactured using bacteria and biofilm
resistant materials for improved water quality.
Premium filters provide a better tasting water
due to the high quality, carbon chemical
removal filter. Sub-micron rated, these
filters have excellent chemical absorption,
removing or reducing chlorine, volatile organic
compounds (VOCs), chemicals, tastes and
odours. All drinking water filtration systems
should be flushed after a period
of non-use.
There are 2 types of filter cartridge sets
oered.
994001 5.0 micron replacement filter
994002 0.2 micron replacement filter
Use only genuine Billi Filter Cartridges as
designed for this system.
If the system has not been used for a period
of 3 days or more, lift the dispenser lever and
flush the system for at least 1 minute.
Filter Cartridges Service Interval
Periodic replacement of your Billi B-1000
filter cartridge is necessary to maintain the
sparkling freshness of your drinking water.
Your Billi Representative will advise you of
an appropriate service interval. As a guide,
the filters should be serviced twice yearly.
In areas where water supply has a high level
of sediment, more frequent replacement of
filter cartridges may be necessary. This will
become evident when a significant drop in
delivery flow rate occurs.
Filter Cartridge Replacement
When you receive your replacement
cartridges, follow the procedure as
outlined below:
1. Turn o water supply to unit.
2. Remove front panel to unit.
3. Turn temperature control to OFF
4. Open tap to release any pressure.
5. Close tap.
6. Grasp the bottom of the filter and pull
towards yourself slowly. The top of the
filter is in a hinged cradle assembly.
It should stop after approximately
30 degrees of travel.
7. The filter can now be released from the
holding cradle by pulling down on the filter.
8. Take care not to spill water in the base
of the tray. If so wipe gently with blotting
paper.
9. Install new filter into the same location
by pushing up into the cradle all the way.
10. Push filter forward until upright and
locked in place.
11. Turn water supply to unit on.
12. Open tap again.
13. Run water for 2-3 minutes to flush all
air out and condition the filter.
14. Close tap.
15. Check for any leaks from around the filter,
hosing or pipe work.
16. Turn temp control to ON & set temperature
to desired level.
17. Close front cover.
4
Page 5
User guide
Billi B-1000.
Thank you for choosing to install a
Billi B-1000 Drinking Water Appliance.
Your B-1000 is manufactured to
exacting standards using high quality
materials and with proper maintenance
and care, should function for many
years.
For information on our filtration
and service contract please contact
Billi Head Oce on 1800 812 321
or email us at service@billi.com.au.
For technical support please call
1800 812 321 and speak to one of
Billi’s experienced technician’s.
To book a service call out request
a filter change or please contact
the Billi Service Centre on
1800 812 321 or book online
at www.billi.com.au
Filter cartridges are also
available for purchase online
at www.billi.com.au
5
Page 6
Page 7
Page 8
Billi Pty Ltd
42 Lucknow Crescent, Thomastown
Victoria 3074 Australia
Telephone +61 3 9469 0400
Facsimile +61 3 9469 0499
www.billi.com.au
Designed and manufactured in Australia.
As Billi Pty Ltd has a policy of continual
improvement, all details are subject
to change without notice. All goods
are sold subject to our published terms
and conditions. Billi is a registered
trademark. 0217
Loading...