Bike2Power iPhone 5 Power Plus User Manual
3. Battery Specifications
1. Input: DC 5V 500 mA (max.)
2. Output: DC 5V 1000 mA (max.)
3. Capacity: 3000 mAh (11.1 Wh)
4. Type: 3.7V Li-ion
5. Operating temperature: -5˚ to 50˚C
6. Storage temperature: -20˚ to 60˚C
4. Battery Pack Usage
1. To start charging the phone with the built-in Lightning connector, press the power button
once. The indicator light will be turned on and stay on.
2. To stop charging the phone, press the power button again. The indicator light will be turned
o.
3. To start charging other devices using the micro USB Power OUT port, continuously press the
power button for 4 seconds. The indicator light will start ashing slowly (once every 2
seconds).
4. To stop charging other devices, continuously press the power button for 4 seconds again.
5. Whenever you start charging any devices or connect the battery pack to a compatible power
source to get it charged, the battery level indicator will be switched on. The indictor will be
in the form of a medium ash (once every 1 second), with the higher number of ashes
meaning the battery power is nearer to full:
- 1 ash: 50% or below
- 2 ashes: 51-60%
- 3 ashes: 61-80%
- 4 ashes: above 80%
After the battery level indicator is shown, the indicator light will return to its normal state.
6. When the battery pack is being charged, the indicator light will ash rapidly (once every 0.3
seconds). When the battery is fully charged, the indicator light will change to another ash
pattern (ash for 0.3 seconds, o for 3 seconds).
7. The battery pack can be charged and discharged simultaneously.
8. The power button, once switched on, can only be manually switched o.
BikeCONSOLE
POWER PLUS
For iPhone 5
Bike Mount with 3000mAh Battery Pack
USER GUIDE
1. Delivery Contents
A. Battery Pack
E. USB to 2.5mm DC (Power In) Cable
C. Mounting Bracket
D. Phone Case
5. Warning
1. Never charge the battery pack with the Power OUT port. Doing so may risk damaging the
battery pack.
2. Always keep the contact pins and contact plates clean.
3. Always switch o the battery pack (with the indicator light o) to conserve power.
4. Do not store or use battery in excess of the designed temperature ranges.
5. Do not place battery in re.
6. Stop using if battery is damaged, excessively hot or showing other abnormalities.
7. Do not disassemble battery or attempt to repair or modify it in any manner.
8. Do not expose battery to moisture or submerge it in liquid. Keep battery dry at all times.
9. Do not charge battery other than using the built-in 2.5mm DC connector.
10. For extended storage, rst charge battery for one hour.
11. Never dispose battery in the garbage.
12. Do not over-tighten mounting bracket to prevent breakage.
13. Do not bend the cover to prevent deformation.
14. The BikeConsole is designed to be splash proof only. Do not immerse it in water.
15. Make sure the BikeConsole is securely locked to mounting bracket before riding.
IPH-2150-M-EN
F. Micro USB to USB Female
(Power Out) Cable
H. Headphone
B. BikeConsole
Case
BikeConsole Power Plus for iPhone 5 is a Made for iPhone product.
“Made for iPhone” means that an electronic accessory has been designed to connect
specically to iPhone, and has been certied by the developer to meet Apple performance
standards. Apple is not responsible for the operation of this device or its compliance with
safety and regulatory standards. Please note that the use of this accessory with iPhone may
aect wireless performance.
G. Rubber Pad
Cable
Passage Plug
I. Allen
Key
www.tigrasport.com
2. Installation
A
Ø20-45mm
D
5
6
1
3
G I
B
2
1
4
2
E
3
4
5
6
H
2
3
2
1
6
5
2
1
1
3
1
2
C
<5°
F
1
3
A. The mounting bracket can be installed on either the handlebar or stem of size Ø20-45mm.
Wrap the strap around the bar, push it inside the slit while rotating the Allen key clockwise
until the mounting bracket stays rmly on the bar.
B. 1. Pull the 2 side levers from the bottom of the case.
2. Open the 2 side latches.
3. Pull the lower latch out a bit to lift up the front cover.
4. Attach the headphone cable passage plug onto the headphone cable by pushing the
stereo connector through the plug (optional).
5. Open the rubber cap on the lower side of the case (optional).
6. Push the headphone stereo connector through the hole and let it stay inside the case
(optional).
C. Gently tilt the Lightning connector up by not more than 5˚.
D. 1. Tilt the phone and gently insert it into the Lightning connector.
2. Push the rest of the phone in until it ts snugly inside the silicone liner.
3. Plug the headphone cable into the phone (optional).
4. Plug in the headphone cable passage plug to prevent water leakage (optional).
5. Close the front cover and position the 2 side latches on the grooves of the cover.
6. Push the 2 side levers down until the front cover is locked.
E. 1. Push the battery pack towards the back of the BikeConsole until the 4 prongs sink inside
the trough.
2
2. Push the battery pack forward until the 4 prongs lock in place.
3. Turn the knob clockwise until the battery pack is rmly locked in place.
F. 1. Place the whole unit on the mounting bracket until the 4 prongs get into the trough at the
back of the battery pack.
2. Slide the whole unit backward until the Quick Release lock in.
3. Turn the knob clockwise until the whole unit is rmly locked in place.
G. Push the power button on the battery pack once to start charging the phone. Push again
to stop.
H. 1. Open the Power IN cap for charging the battery pack. Open the Power OUT cap for using
the battery pack to charge other devices.
2. Screw in the 2.5mm DC connector of the Power In cable to the Power IN port, and connect
the USB connector at the other end of the cable to a compatible power source for charging
the battery pack. Plug in the micro USB connector of the Power Out cable to the Power OUT
port, and plug in the charging cable of the other device to the female USB connector at
the other end of the cable to charge the device with the battery pack. To start charging,
push the power button continuously for 4 seconds.
3. Rotate the Power In cable clockwise to x it rmly on the Power IN port.
I. Rotate the BikeConsole to your desired mounting position.
Loading...