Connecting people through extraordinary audiovisual experiences™
Vidi 100 / 150
Installation and Operation Guide
Features
• 4K High Denition
• Full function USB 3.0 interface
• 120° wide angle eld of view
• Built in microphone array with noise
suppression
• Reduced 2D / 3D image noise
• Easy installation
• Vidi 150 has smart autoframing
technology
Contents
Vidi 100 or Vidi 150
Remote
USB Cable
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
W: www.biamp.com
Installation
1. Mount the camera by placing on a stable at surface or by opening the
stand and clamping the camera on the display/monitor.
Note: The camera can also be mounted to a third party mount utilizing a 1/4"-20
UNC thread. Just unscrew the camera from the attached mount and reinstall on
the new mount.
2. Plug the USB cable into the camera and computer (OS & hardware
requirements on the next page).
Note: A USB 3.0 port is required for 4K resolution. Up to 1080p
resolution is available on USB 2.0 connections. The camera may be
plugged into a USB extender with support for isochronous data transfer.
USB Cable
(supplied)
Vidi 100/150 Install Guide
Safety
Electric Safety - Installation and operation must comply
with applicable local electrical safety standard.
Caution - Avoid stress, vibration or liquid exposure in
transport, storage and installation.
Installation - Mount the camera on a stable smooth
surface (shelf, wall display). The product enclosure is
made from organic material and any contact with
corrosive material should be avoided.
page 2
Vidi 100/ 150 Features
IR Sensor
Stand
Lens
Omni-directional
Microphones
USB 3.0
USB 3.0 port
Type B
Operation Information
USB - Works with the following Operating systems
• Windows® 7 (only 1080p and below are supported)
• Windows 8.1, Windows 10 or higher versions
• macOS ™ 10.10 or higher versions
• Google ™ Chromebook ™ Version 76.0.3809.136 or higher
versions
• Linux (support for UVC needed)
• Android
Hardware requirements:
• 2.4 GHz Intel® Core 2 Duo processor or higher
• 2 GB RAM or more
• USB 2.0 port (USB 3.0 required for 4K)
Operating temperature: -10° C - 40°C (14°F - 104°F)
Avoid the following:
• Do not aim at an extreme bright object for a long period of time, such as
sunlight, light sources, etc.
• Do not operate in unstable lighting conditions, image will icker.
• Do not operate close to powerful electromagnetic radiation, such as radio
transmitters, etc.
Vidi 100/150 Install Guide
page 3
Remote Control
Power / Standby
Number Keys
Camera selection
F Keys
Preset
Home
Return
Zoom
(Slow or Fast)
Left / Right Set
Focus
Reset
Arrow keys
Menu
Backlight
P/T Reset
Remote needs (2) AAA batteries (not included)
Remove rear cover, install batteries observing
correct polarity as indicated, and reinstall cover.
Vidi 100/150 Install Guide
page 4
Remote Control Keys
Power/Standby: Toggles normal or standby operation
Camera selection: 1 is default, but the remote can be used to control up to 4
cameras.
Number keys: 0-9 can be used to set or recall a preset
F keys: IR remote control key. (ie [*]+[#]+[F1]: Address 1) (F1 is the default)
Note: Will also toggle a zoom lock function - Press once returns to the home
screen and disables zoom functions. Pressing again enables the zoom functions.
Pressing the F1 key with the Vidi 150 toggles both the Zoom and Autoframing
functions O (home) and then back On.
Preset: Sets presets. Press Preset followed by a number key will save the settings to
that number.
Reset: Clears presets. Press Reset followed by a number key will clear the settings
assigned to that number.
Home: Conrms menu selection, enters the sub menu, or return the lens to the
middle (straight on) position after zoom press.
Arrow keys: Navigate through the menu.
After zoom key press: pressing the arrow keys will move the lens in that direction.
Pressing Home returns the lens to the middle position.
Return: Goes back one level on the menu.
Menu: Enters or exits the Menu
Zoom Slow: Pressing the + or – key zooms the camera slowly
Zoom Fast: Pressing the + or – key zooms the camera quickly
L/R Set: Sets direction of the Pan/Tilt
Simultaneously pressing the L/R Set +1 will set the pan/tilt turning direction
Simultaneously pressing the L/R Set +2 will set the direction to go the opposite way
Backlight: Toggles backlight compensation
P/T RST: Resets pan/tilt to factory default.
Focus: Not enabled.
Additional information about the Vidi cameras and operation is available on
Cornerstone (Biamp's Technical Support Knowledge Base) - here.
Vidi 100/150 Install Guide
page 5
Menu Settings
MENU
Press [MENU] button to display the main menu on the normal screen. Use arrow
buttons to move the cursor to the item to be set. Press the [HOME] button to select
and enter the corresponding sub-menu.
Note: "SETTING" will only appear in the Vidi 150 menu.
MENU
Color
Setting
Information
Restore Default
Exit
COLOR
From the main menu, move the cursor to [COLOR], and press [HOME] key to select.
Press left/right arrow keys to choose the options
Color menu examples:
COLOR
WB Mode Auto
Return
Menu Options:
WB-Mode: White balance mode: Auto, Indoor, Outdoor, One Push, VAR and Manual.
Adjustment options vary in WB modes (other than Auto) and may include:
Saturation: 0 – 100, or 60 – 200.
Hue: 0 – 14.
R Gain: Red gain: 0 – 255
B Gain: Blue gain: 0 – 255
RG Tuning: -10 to +10
BG Tuning: -10 to +10
Colortemp: 2500K – 8000K
Vidi 100/150 Install Guide
COLOR
WB Mode Manual
R Gain: 225
B Gain: 175
Saturation: 100%
Hue: 7
Return
page 6
SETTING (VIDI 150 ONLY)
From the main menu, move the cursor to [SETTING], and press [HOME] key to
select.
Setting menu example:
Menu Option:
SETTING
Tracking On
Return
Tracking: On, O, Gradual, Demo
INFORMATION
From the main menu, move the cursor to [INFORMATION], and press [HOME] key to
select.
Information menu example:
INFORMATION
Version 1.0.01
Model Vidi 100
Date 2022-05-01
Return
RESTORE DEFAULT
From the main menu, move the cursor to [RESTORE DEFAULT], and press [HOME]
key to select.
Restore Default menu example
RESTORE DEFAULT
Yes
No
Return
Vidi 100/150 Install Guide
Menu Options:
Yes: Conrm restore factory settings.
No: Cancel restore factory settings.
Note: Press [HOME] button to conrm, all
parameters are set back to factory default,
include IR Remote Address.
page 7
Maintenance
• Use soft cloth or tissue to clean the camera cover.
• Only use a soft dry cloth to clean the lens. If the camera is very dirty, use
diluted non abrasive detergent on a cloth. Do not immerse in water. Do not
use solvents which may damage the surface.
CONTACT US
Email: support@biamp.com
Web: support.biamp.com
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA
Warranty: biamp.com/legal/warranty-information
Safety & Compliance: biamp.com/compliance
W: www.biamp.com
17OCT2022
Loading...