Page 1
RP-C2 - Remote Panel (Input Connectors)
Instruction Manual
RP-C2
(Biamp #909-0171-00): The RP-C2 is a remote panel, which consists
of one XLR and two RCA input jacks mounted on a grey ‘decorator’ style cover
plate, with a single-gang ‘cut-in’ style PVC electrical back-box and barrier-strip
wiring connector. An internal transformer and resistors provide summing,
balancing, and isolation for the RCA inputs. The RP-C2 may be used to
provide remote inputs as specified for the following BIAMP products:
products
801 Mic/Line Mixer . . . . . . . . . . . . . Mic/Line Inputs
601 Mic/Line Mixer . . . . . . . . . . . . . Mic/Line Inputs
301 Mic/Line Mixer . . . . . . . . . . . . . Mic/Line Inputs
CMA Series Mixer/Amplifiers . . . . . . . . Mic/Line Inputs
IWA250 In-Wall Mixer/Amplifiers . . . . . . Mic/Line Inputs
autoONE Automatic Mixer . . . . . . . . . Mic/Line Inputs
VRAM Automatic Mixer . . . . . . . . . . . Mic/Line Inputs
SPM723 Stereo Preamp/Mixer . . . . . . . Mic/Line Inputs
MSP22e Signal Processor . . . . . . . . . . Line Inputs
PMX84 8x4 Matrix Switcher . . . . . . . . Line Inputs
The RP-C2 includes a single plug-on barrier-strip wiring connector for ease of
installation. See associated product manuals for input wiring specifications.
See next page for back-box installation & block diagrams.
RCA Input Transformer Tap:
set for a 1:1 ratio (output level = input level). A jumper strap (J4) is located on
the circuit board, above the RCA jacks, which allows the transformer input tap
to be changed for a 1:2 ratio. This provides a 6dB increase in output level from
the transformer. For a 1:2 ratio, move the J4 jumper strap one pin towards the
rear of the circuit board, to the "1:2" position, using needle-nose pliers. A 1:2
ratio may help compensate for low-level sources or signal loss in long cables.
Output Connector:
signals from the RP-C2, for connection to inputs on the associated products. A
common ground connection is used for both the XLR and RCA outputs. Each
output connection is balanced, providing both a positive (+) and a negative (-)
terminal. The unbalanced stereo RCA input signals are resistively summed
into mono, then passed through a transformer for balancing and isolation.
functions
From the factory, the RCA Input Transformer is
This plug-on barrier-strip connector provides the output
push
RP-C2
RCA
XLR
transformer
output
connector
Biamp Systems, 10074 S.W. Arctic Drive, Beaverton, Oregon 97005 U.S.A. (503) 641-7287 www.biamp.com
an affiliate of Rauland-Borg Corp.
Page 2
K
y
Back-Box Installation
Remove the back-box from the front panel (controls). Route cables through a
‘knock-out’ hole on the rear of the back-box. Install the back-box in a wall or
panel, in the same orientation as any standard single-gang electrical box.
The mounting surface may be from 1/8” to 1” thick
(3.175mm to 25.4mm)
The mounting cavity must be exactly 3.6” high,
2.25” wide, and at least 2.75” deep
(91.44mm H x 57.15mm W x 69.85mm D)
Insert the back-box into the wall or panel, then tighten the flange screws until
the flanges hold the box securely in place. Wire the remote panel pre-wired
pigtails to the appropriate cable conductors. Soldered connections with heatshrink insulation, or properly sized wire nuts, are recommended. Mount the
front panel to the back-box, being careful not to pinch or short the wires.
NOTE: When an RP-S4 is used with an RIK Remote Interface Kit, the RI
circuit board will not fit inside the standard single-gang electrical back-box.
Therefore, the RIK must be installed external to the back-box (
to be connected using the wire harnesses provided). An alternative is to utilize
a double-wide electrical back-box, which has the additional space for an RIK.
.
.
et close enough
Back-Box
flange
knock-outs
flange
RP-C2 Block Diagram
2
3
1
+
-
+
-
585.9171.00
Biamp Systems, 10074 S.W. Arctic Drive, Beaverton, Oregon 97005 U.S.A. (503) 641-7287 www.biamp.com
an affiliate of Rauland-Borg Corp.
Loading...